Search Documents

By Harold Markus, Gerhard Derge

The first paper1 of this series described a technique of careful surface preparation by means of which reproducible results may be obtained from potential measurements of the behavior of tin in carbonate solutions with a pH range from 8.4 to 11.2. It then went on to establish the behavior of pure tin electrodes under these conditions and showed that the metal remains active at all times, though the steady potential attained after several hours decreases from 1.12† volts at a pH of 12.6 to 0.6 volts at a pH of 8.4. This behavior may serve as a norm with which all other data can be compared. In the second paper,2 small amounts of other anions were added to the carbonate solutions and the conclusion was reached that the common impurities encountered in alkaline materials packaged in tin do not increase corrosion. In fact, in some cases these anions may actually promote the formation of protective films. The present paper rounds out this survey by presenting data on the influence of cations added to the carbonate solutions, as well as the effect of alloy additions to the tin. In many cases the potential data are supplemented with weight-loss measurements. Information is also presented on the effects of some additional anions, the influence of gases above the electrolyte, the behavior of high-purity tin, and the effect of atmospheric oxidation on the corrosion resistance of the above-named alloys. Analysis of the entire body of data discloses some general rules applicable to corrosion in carbonate solutions. The experimental methods used are the same as those previously described. Experimental Data Cations.—The carbonates of the cations K+, Li+, NH4+, which are soluble, were studied in the same way as the anions, by adding 0.01 mol of the metal carbonate to one liter of 0.1 M sodium carbonate solution, pH 11.2, or to 0.1 M sodium bicarbonate, pH 8.4. The other metallic carbonates are only slightly soluble, of the order of 10-3 mols per liter or less, and the sodium carbonate solutions were saturated by adding excess reagent several days before the experiment, shaking frequently, and filtering just before use. The chemicals were c.p. grade in each case except the indium salt. This salt was prepared by solution of the metal in hydrochloric acid and precipitation by addition of Na2CO3. These cations may be divided into two classes, according to their effect on the potential behavior of the tin: (I) normal, (2) passive. To offer a basis of comparison, curves I of Figs. I and 2 are given to illustrate the behavior of tin in carbonate solutions saturated with CaCO3. These curves are the

Jan 1, 1941

By F. N. Rhines, B. H. Alexander

MUCH attention has been directed to the effects of grain size upon the properties of alloys, but there has been scant study either of the conditions that determine the pattern and dimensions of den-drites in metal systems, or of the influence of their shape and size upon the overall properties of cast-ings. The aim of the research that is about to be described has been to investigate the effect of vari-ous factors upon the mode of formation of dendrites in alloys by measurements of the distance between adjacent dendrite arms (dendrite spacing). Early investigators, including Grignonl and Tschernoff,2 showed that a metal dendrite is com-posed of a tree-like system of stalks and branches arranged in a simple geometrical pattern. North-cott and Thomas3 demonstrated that, in the face-centered cubic solid solutions of copper-base, these stalks and side arms all lie in (100) directions in the crystal. Several investigators, including Sauveur and Chou,0 Sauveur and Reed,' and Martin and Mar-tina have reported that the addition to steel of alloy-ing elements, such as nickel, chromium, and molybdenum, not only makes the dendrites easier to reveal by etching, but makes them coarser. The latter authors8 proposed that the coarsening of the dendrites is roughly proportional to the increase in the temperature range of freezing, caused by adding the alloying elements. Sauveur and Chou6 showed, in addition, that the dendrites are coarsened by a decreased rate of cooling of the casting. Measurement of Dendrite Arm Spacing Among the physical conditions that could be ex-pected to have an influence upon the dendrite arm spacing, that appears in a cast metal, are: composi-tion, rate of freezing, crystal structure, and type of constitution. The relationships obtaining between these variables and the dendrite dimensions have been examined, in the present research, by measur- ing the arm spacing in a wide variety of alloys, listed in tables II through VI. Alloy compositions are recorded in the tables by showing the symbol of the major metal followed by the percentage and symbol of the alloying agent; thus, "Al-10Ag" is an aluminum-base alloy containing 10 pct of silver. Although none of the alloys were analyzed, an im-pression of their degree of purity may be obtained from that of their component metals given in table I. Five hundred grams of each alloy was made by melting in small clay-graphite crucibles in an elec-tric muffle furnace. After alloying the temperature was adjusted to 50" to 75°C above the liquidus and the melts were poured into cast iron molds, at room temperature, the molds having a wall thickness of 1 in. and a cavity 11/2 in. sq in cross-section. Each ingot, thus cast, was sectioned at mid-height and the sectioned surface was polished and etched for metallographic examination. Dendrite spacing meas-urements were made at three positions, namely, ad-jacent to the mold wall, midway between the wall and the center of the ingot, and at the center (desig-nated e, m, and c respectively, in the tables). A typical series of microstructures is presented in fig. 1. For each measurement, the average was taken of the dendrite spacing of several grains covering a zone about 2 mm wide. Only those grains which had a major dendrite axis nearly in the plane of polish were selected in order to eliminate corrections for orientation differences from grain to grain. Although the dendrite spacings were measured to the nearest thousandth of a millimeter, the values listed in the tables are thought to be significant only to the nearest hundredth of a millimeter. The larg-est difference in readings found, when various ob-servers rated the same specimens, was 0.012 mm; the largest difference between corresponding meas-urements upon duplicate specimens was 0.027 mm.

Jan 1, 1951

By G. S. Brooks

The tendency of the oxides of such metals as aluminum, zinc, chromium, and calcium to form compounds at high tempera tures with iron oxide is well established by past investigation. Data of this reaction, as developed in laboratory research, have been contributed by Burleigh, Hofman, and Wells, in America, and by many others abroad. A partial bibliography of the subject is appended. From these authorities we learn that the ferric oxide here has the function of an acid, giving in the case of ZnO a zinc ferrite, with a normal composition of ZnOFe2O3 This formation of zinc ferrite particularly affects the success of such processes as leaching or magnetic separation, and thus becomes practically important to the metallurgist. But the meager existing data do not entirely agree; and quantitative results from muffle-practice are conspicuously absent. Furthermore, it being of some general importance to the zinc smelter in both roasting and reduction, the following few notes of operations oil a commercial scale are contributed: I. Physical Properties of Zinc Ferrite. As formed for the most part synthetically by investigators, zinc ferrite exhibits characteristic physical properties, such as octahedral crystals, dark color, and a density over 5, together with a slight magnetic attractability. In examining with the microscope many products of mechanical muffle-roasting kilns, it is, however, impossible to find individual grains which can be identified as consisting entirely of zinc ferrite. The variety of colors, especially where each grain of blende was mechanically free from marcasite, rather conveys the impression of a partial ferritization of the grain. One side or end, for example, may often have the hard, dense surface and dark red to black color of the ferrite, while the balance shows the usual light yellowish brown of a normal iron-free blende.

Jan 1, 1914

By P. R. Sperry, P. A. Beck, J. Towers

Dahl and Pawlek1 found that electrolytic copper develops extremely coarse grains at 1000°C after about 90 pct reduction by rolling. This coarsening occurs only under conditions of penultimate grain size, deformation, and alloying which lead to the "cube" recrystallization texture.l,2,3,5 The peculiar angular shapes and straight grain boundaries of the coarse grains were noted by several investigator.1,4,5 On the other hand, coarsening in Fe-containing aluminum or in AI-Mn alloys8 does not depend on a "cube" (or any well developed) recrystallization texture. It is true that increasing deformation by rolling, and, therefore, an increasingly well developed re-crystallization texture, are associated with decreasing incubation periods of coarsening.6-7-8 Nevertheless, coarsening readily develops in aluminum even after only 30 pct reduction by rolling, where the recrystallization texture is very weak.6,8 Also, coarsening was observed by Jeffries9 many years ago in sintered thoriated tungsten, which presumably has no preferred orientation. In all these cases coarsening is associated with grain growth inhibition by a dispersed second phase.8,9 The annealing temperature has to be suficiently high to overcome the inhibition at a few locations. But if it is too high, growth starts at many points, and the resulting grain size becomes much smaller.9 Normally, the coarse grains are more or less equiaxed, and the boundaries have a typical ragged appearance.6.8 Cook and Macquarie4 demonstrated that, in addition to the texture-dependent coarsening previously found at 1000°C,l electrolytic tough pitch copper may also coarsen at 800°C after 50 pct reduction by cross rolling. The coarse grains formed under such conditions have rounded shapes and ragged boundaries, like those in aluminum. When the annealing temperature is higher, the tendency for their formation decreases. All these observations suggest that the coarsening at 800°C is associated with inhibition by a second phase. Actually, coarsening at 800°C after 50 pct reduction by cross rolling was observed only in tough pitch copper,4 which contains Cu2O particles. On the other hand, the texture-dependent 1000°C coarsening occurs in both tough pitch and oxygen-free copper;4 it does not appear to depend on the presence of a dispersed second phase. However, the interpretation of the 800°C coarsening in Cu after 50 pct rolling as an inhibition-dependent process, similar to the coarsening in A1-Mn alloys, is somewhat weakened by the fact that this coarsening was reported4 to occur only after cross rolling, and not after straight rolling. It was, therefore, decided to re-examine this question. A 1 in. diam electrolytic tough pitch copper rod, No. 2 hard drawn, was annealed for 20 min at 700°C, rolled to 0.5 in., annealed 10 min at 700°C, and straight rolled to 0.064 in. It was then given a penultimate anneal of 20 min at 500°C and it was cut into four sections, which were given final reductions by straight rolling as follows: A 30 pct reduction of area B 50 pct reduction of area C 70 pct reduction of area D 90 pct reduction of area Specimens cut from the four sections were finally annealed at 800°C in an oxidizing atmosphere. Strip A remained fine grained up to 10 hr, but the specimen annealed 12 hr consisted of only 2 large grains. Strip B had a few scattered large (1/2 to 3/4 mm) grains after 1 min, although the balance of the specimen consisted of fine grains of about 0.02 mm. After 5 min there were several 10 to 15 mm grains present, and after 1 hr strip B was completely coarsened. The coarse grains had the same characteristics (see Fig 1) as those obtained by Cook and Macquarie at 800°C after cross rolling. Strip C had several grains of 0.05 to 1 mm after 1 min, but it was still largely fine grained after 12 hr. After 48 hr it consisted entirely of grains of about 0.5 to 4 mm, with an extraordinarily large number of twin bands. Strip D remained com- pletely fine grained after 4 hr at 800°C. These results indicate that, in the deformation range of 30 to 70 pct reduction, the incubation period for coarsening as well as the rate of growth and the final size of the coarse grains decreases with increasing deformation. Similar

Jan 1, 1950

By Samuel S. Adams

Potash, the generic term for a variety of potassium-bearing minerals, ores, and refined products (Table I), owes its importance as an industrial mineral to the potassium requirement of growing plants. The term "potash" originally referred to potassium carbonate produced by the leaching of wood ashes. This process, for which the first U.S. patent was issued in 1790, was the basis for the largest United States chemical industry in the early nineteenth century. The agricultural use of potash soon eclipsed the chemical applications following the German discovery in 1840 that potassium is essential to plant growth. The initial discoveries of large deposits of soluble potassium minerals, essential for agriculture applications, were made in 1857 in Germany and in 1914 in the United States. More than 90% of the 20.4 million short tons K2O produced in the world in 1970 (Eilertsen, 1971 ) was derived from marine evaporite deposits and approximately 90% was used in fertilizers. The potassium content of an ore, mineral, or product is customarily expressed as % K,O, a unit of measure which is neither a natural nor synthetic compound of potassium (1 .O% K is equivalent to 1.2046% K,O) . Geology Potassium, the seventh most abundant element in the earth's crust, is present in silicate minerals in igneous, sedimentary and meta- morphic rocks. Potassium is also a major constituent of many surface and subsurface brines (Table 2). Economic potash deposits are essentially restricted, however, to widespread, thick accumulations of marine chloride evaporite deposits. These deposits yield high grade, large tonnage ore bodies, many of which are amenable to low cost mining and beneficiation. The products from these deposits are, moreover, ideal for use in fertilizer because of the high relative solubility of the potassium chloride and sulfate evaporite minerals. World potash production and reserves for such de- posits so vastly overshadow other sources of potassium that the following discussion will be limited largely to potash deposits in marine evaporites with brief reference to certain potash-rich brines. Approximately 85% of current domestic production is from bedded salt deposits and much of the balance is from brines. Marine evaporite deposits are accumulations of salt minerals deposited in structural sedimentary basins through the evaporation of sea-water or mixtures of seawater and other brines. The salt minerals are precipitated in assemblages and sequences of assemblages as determined by the compositions of the brines and the solubility relations in the salt systems (D'Ans, 1933). The evaporation of seawater normally yields carbonate minerals as the first precipitates (Table 3). Further evaporation and concentration of the brine leads to the precipitation, in succession, of sulfate, chloride, and supersaline mineral assemblages including the salts of potassium and magnesium. The common minerals, ores, and products of potassium deposits are listed in [Table 1]. Many potash deposits contain accessory evaporite minerals together with a variety of detrital and authigenic silicates (Braitsch, 1971).

Jan 1, 1975

By C. W. Davis, R. S. Dean

AMONG naturally occurring inorganic compounds, magnetite has many unusual and interesting properties, and it is the purpose of this paper to call attention to these properties and review possible uses of magnetite that might be based on them; in other words, to see what uses may be found for magnetite as a physical rather than as a chemical entity, as a mineral rather than as an iron ore. The Mineral Physics Studies initiated in the Metallurgical Division of the U. S. Bureau of Mines a few years ago gathered together much information on mineral properties, and they are therefore the principal source of material for this paper. Magnetic Properties Of Magnetite And Possible Uses As A Magnetic Material Magnetite is unique among minerals for its great magnetic susceptibility, approximately one-third that of soft iron, and some magnetites are permanent magnets, or lodestones. The literature contains many measurements of magnetic properties of individual magnetite crystals, but no systematic survey of the effect of mechanical preparation and heat-treatment was available until the recent investigations of the Bureau of which included not only susceptibility but coercive force and remanence as well. For the purpose of orientation, Table 1 gives the magnetic properties of several samples of magnetite and of a few other substances3. This table indicates that when ordinary magnetite is powdered it decreases in susceptibility and increases in coercive force and remanence, approaching the properties of lodestone. The properties of lodestone are in fact probably due to the development of very large internal surface on fine grain size4.

Jan 1, 1937

By D. W. Hutchinson, W. W. Wen, A. A. Terchick, J. C. Anderson

It is estimated that approximately 3% of the raw coal processed today in coal preparation plants throughout the nation will ultimately report to slurry-tailing disposal (Anderson, 1975). The usual disposal method is to pump refuse slurry containing - 48 mesh (300 pm) refuse into dams or impoundments constructed of coarse refuse. The failure of an impoundment at Buffalo Creek, Saunders, WV (Anon., 1972) resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of federal regulations dealing with the construction, operation, and final abandonment of coal refuse disposal area. As a consequence of these regulations, the use of the landfill/impoundment method of disposal became in some cases economically unfeasible or technically impossible. US Steel has studied a number of alternative methods of refuse disposal. During an investigation of mechanical dewatering with a pressure filter, portland cement was added to the slurry to solidify the filter cake. Because of the success of the cement addition, it was decided to study the stabilization of fine coal refuse slurry through use of cement-type additives. The goal of the investigation is to develop a process that will use cement-type additives to solidify the refuse slurry into a form that can be handled and stacked with the coarse refuse, thus eliminating the need for slurry impoundments.

Jan 1, 1982

By Frederic Benard

PRIOR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow-gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of trans-ferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 114 miles. Although common in steel practice, the transportation of blister copper in this form had not previously been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended oil the design and combination used for the particular experiment. The vessel was filled with approximately 2 ½ tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack oil refractories.

Jan 1, 1938

By R. V. Ramani, C. J. Bise

The potential of deep-mineable coal reserves in the western United States for meeting future energy needs has been recognized for quite some time. However, two of the major constraints tending to limit the development of these underground reserves are the great thicknesses of the coal seams encountered and their high pitch. Although new mining methods may need to be developed to recover these reserves, at least in the short-term the industry has to incorporate presently available equipment not originally designed for thick-seam mining. The purpose of this paper is to present an analysis of the various equipment in use today and their possible application to thick-seam mining. The paper also addresses various ground control and safety considerations unique to thick-seam extraction.

Jan 1, 1984

By J. E. Schiller, S. E. Khalafalla

Due to its unique surface properties, magnesium oxide (MgO) is an excellent medium to filter asbestos and other suspended solids from water. MgO operates up to twice as long as a sand filter before backwashing is required while flow rate and filtrate clarity are as good or better with MgO.

Jan 1, 1984

By Glenn A. Marsh, George Bernard

It is often assumed that aerated oil field brines which are to be injected underground contain dissolved oxygen in amounts which will cause appreciable corrosion. Through the use of a new portable dissolved oxygen meter, accurate determinations were made at three brine conditioning plants. At two older plants, dissolved oxygen concentration in the final treated brine was found to he almost zero In spite of aeration during the conditioning process. At a new plant, dissolved oxygen was initially present but disappeared soon after the brine was "inoculated" with oxygen-free brine from one of the other plants. Corrosion tests at the two older plants have substantiated predictions that the brines would lint be corrosive. These results show that mechanical deaeration may not always be required in brine treating plants. INTRODUCTION The present work was undertaken to add to our knowledge of aeration and deaeration of oil field brines in brine conditioning plants. It is commonly assumed that brines which are exposed to the air soon become more or less saturated with dissolved oxygen. Since oxygen-containing brines are known to be corrosive, precautions are often taken to keep air out of brine through the use of closed systems or mechanical deaeration. The study of oxygen in brine has been seriously hampered in the past because of the lack of a suitable analytical tool. The standard Winkler method for the determination of dis-solved oxygen is satisfactory for use in fresh water, but not in many oil field brines. Corrections have to be made for a number of reducing substances such as ferrous iron and hydrogen sulfide which are commonly present in natural brines. Very often the correction factors are much greater in magnitude than the amounts of oxygen which are to be determined, and consequently erroneous results are obtained. Also. erratic Winkler data are obtained when appreciable concentrations of calcium and magnesium salts are present. The first step in carrying out a systematic study involved designing a portable dissolved oxygen apparatus which would operate in natural brines. Subsequently, this apparatus was used in three brine conditioning plants. Dissolved oxygen data obtained here, and certain corrosion rate data, illustrate the interesting behavior of oxygen in these oil field brines. APPARATUS A portable dissolved oxygen meter described in detail elsewhere,' was developed specifically for use with oil field brines. It is a polarographic apparatus employing a small rotating platinum electrode (cathode) and calomel reference electrode (anode). A potential of 0.7 volts is applied across the electrodes while they are immersed in the brine to be tested. 4References given at end of paper.

Jan 1, 1952

By O. C. Wheeler

The activity in exploration and in the acquisition of prospective oil lands that reached such a high level in Colombia during 1936 gained momentum and reached unprecedented proportions during 1937. Both national and private lands were taken up. In the Magdalena Valley above Puerto Berrio, leases on large tracts of private lands are held by Richmond (Standard of California), Shell and Texas. Tropical also owns leases covering a block of acreage in this area near Honda. From Puerto Berrio to El Banco most of the acreage is of national ownership, and concessions covering parts of this area have been granted to Tropical, Socony Vacuum, Shell and others, while applications for additional concessions are pending. Latterly leases on private lands below the Lebrija River have been taken out by Shell and Richmond. In the drainage basins of the Meta and Guaviare Rivers of the Llanos region of eastern Colombia, several of the major companies have carried on geological exploration and it is understood that some private properties have been leased or optioned. Under Colombian law, subsoil rights are reserved to the nation on all lands that passed from Government ownership after Oct. 28, 1873. Private titles antedating that day carry both surface and subsurface rights. Conditions under which lands may be acquired, explored and

Jan 1, 1938

Jan 1, 1893

By M. J. Hordon, M. A. Wright

The well-defined increase in fatigue life observed o many metals cyclicly strained at vacuum levels below 10-1 to 10-3 torr has been attributed to the critical retardation of oxygen or water vapor chemisorption at the crack tip during crack propagation.1-3 In the absence of strongly adsorbed surface films, crack re-welding during cyclic compression or dislocation escape from the plastic zone around the crack tip has been proposed to account for the observed decrease in the rate of crack growth. The increase in the critical pressure required for the transition in crack growth rate with temperature experimentally determined for aluminum was found to be generally in accord with the adsorption rate model.4 However, although the adsorption mechanism would also predict an increase in transition pressure and fatigue life with increase in cyclic loading rate, and such effects were noted by Snowden5 for lead and Hordon3 for aluminum, the opposite results were reported by Kramer et al.B in studies on aluminum. The present note describes some recent measurements of the fatigue properties of 1100-H14 aluminum at low pressures to determine the specific effect of cyclic strain frequency in the transition pressure range. Flat cantilever-type specimens of 1100-H14 aluminum shaped to produce a uniform strain gradient along the gage length were tested in reverse plane bending at constant deflection amplitudes in two independent multi-specimen vacuum fatigue systems. One series of tests using 2-in. gage length specimens was conducted in an ion pumped apparatus with 107 torr and 50 cps capacity, denoted as Unit I, utilizing fixed mechanical cams to impose the strain amplitude. An independent test series using shorter 1-in. gage length specimens was conducted in a cryopumped apparatus designed for extremely low pressures below 10-10 torr, denoted as Unit II, using an electromechanical vibrator at non-resonant frequencies up to 150 cps to provide the deflection. Both vacuum fatigue units and associated test procedures have been described previously.3'7

Jan 1, 1969

By Corale Brierley

The effect of hydrogen peroxide (H202) on growth and respiration of Thiobacillus thiooxidans and Thiobacillus ferrooxidans, organisms involved in acid leaching of copper sulfide minerals and uarnium oxides, was examined. Oxygen uptake and growth by T. thiooxidans were totally inhibited after contact with 0.82 mM H202. Complete inhibition of oxygen uptake by T. ferrooxidans occurred at 8.75 mM H202, and growth was inhibited after 6 hr exposure to 2.06 mM H202. Higher concentration of H202 can be used without detriment to thiobacilli if it is dissipated prior to reaching the oxidation pond or dump surface.

Jan 1, 1980

By L. H. Ketchum, T. L. Theis, W. H. Engelmann

The use of a suspended growth system of Thiobacillus ferrooxidans attached in a film to individual particles of bentonite and operated as a sequencing batch reactor is shown to be a practical way of oxidizing ferrous iron in acid mine drainage. This component, followed by limestone neutralization, is both a technically and economically feasible approach to treating these waste waters, compared to existing and other proposed methods. The advantages, in addition to less expense, are greater safety, acceptable treatment at a lower pH, lower solids buildup, less danger of overtreatment, and greater flexibility in operational characteristics. In this paper, data on the continuous bench scale operation of the system under a variety of conditions shows sustained levels of oxidation in excess of 98%. Capital and operating costs are projected to be $80/1000 m3 ($80 per 35, 000 cu ft) of waste water.

Jan 1, 1985

By Wido Tilmann

13.6-1. Importance. In Germany there are large tertiary brown coal reserves, most of which are located close to the surface. Therefore, brown coal has been recovered for many years by means of opencast methods. By utilizing a high degree of technology, a rational operation has been achieved, and as a result, the mining techniques have become renowned all over the world. After the war, all the dredgers and overburden spreaders, as well as the means of conveyance, had to be redeveloped for adapting this equipment to the changing conditions of the deposits. Numerous auxiliary machines were adopted from the American earth moving industry and altered according to the different requirements. As a result of such technical developments, the output per man and per shift was increased remarkably in spite of the deterioration of the geological conditions. In the whole of Germany, the total reserves of brown coal amount to 100 billion metric tons, of which 60 billion tons are situated in the Federal Republic of Germany. In the latter area, 8.5 billion tons will be recover- able by opencast means, of which 3.5 billion tons are already developed. The annual output reached 102 million tons in 1965. This total figure comes from four different mining districts: Rhineland, Helmstedt (town at the border of the Soviet occupied zone), Hesse, and Bavaria. The production figures (1965) are as follows: [ ]

Jan 1, 1968

By G. A. Parks, C. Kovacs

The xanthate flotation of chrysocolla can be improved by preheating the ore to 500° to 600°C. Addition of water vapor reduces the preheating temperature required. The temperature range of flotation improvement correlates well with the range over which dehydroxylation occurs. This observation is consistent with changes in the structure and properties of the mineral as detected by measurement of solubility, D.T.A., T.G.A., X-ray diffraction, and infrared absorption and with recently proposed explanations of chrysocolla flotation. A brief experiment by one of the authors several years ago showed that exposure of chrysocolla to high temperature water vapor resulted in increased recovery by subsequent xanthate flotation. Recently renewed interest in flotation and thermal properties of chrysocolla1-5 prompted further study of this effect and more detailed reporting.6 This paper explores the response of pure chrysocolla recovery in Hallimond tube flotation tests to the time and temperature of exposure and to changes in the water vapor pressure. Brief attention is paid to the effects of such treatment on accessory minerals. A single experiment with flotation of chrysocolla from an ore is reported. MATERIALS Chysocolla from Inspiration, Gila County, Ariz. was crushed in a porcelain mortar, cleaned of visible and magnetic impurities, and screened to obtain -48 +65 mesh (Tyler) material for flotation test work. The clean material contained 28.5% Cu and was identified as chrysocolla by comparison of X-ray diffraction, D.T.A., and infrared absorption data with that reported for similar materials by others.4,5,7 Samples of malachite and chalcopyrite, prepared in a similar way, were also identified by X-ray diffraction. The sources of these materials are unknown. A sample of chysocolla-bearing oxidized copper ore from Pima, Ariz. was crushed and dry ground for thermal activation and subsequent flotation. PROCEDURES Activation: The apparatus used for exposure of materials to high temperature water vapor is illustrated in Fig. 1. The furnace temperature was controlled to ±5°C Water vapor pressure was controlled by pre-saturating a nitrogen carrier stream with water in an adjustable thermostatted saturator (multiple bubbler). A water manometer and capillary orifice flow meter were used to measure nitrogen flow rates for activation and for subsequent Hallimond tube tests. Gas flow rate and temperature were adjusted prior to introduction of samples. Exposure time was measured from the moment of introduction of the sample to the furnace, hence includes an initial drop below the control temperature. After heating, the samples were removed from the furnace and stored at room temperature in air. Representative samples of activated materials were examined by X-ray diffraction and infrared absorption.

Jan 1, 1967

By A. J. Langhammer

A. J. Langhammer.—That is rather asking a question of the wrong man. However, I will reply to the question from our point of view. There is a considerable amount of iron powder available but the properties vary over a wide range. Powder metallurgy has progressed to the stage where we recognize certain requirements in powdered iron, and what may be a good powdered iron for one application will not necessarily fit the picture for the next one. Further, I believe that there is room for great improvement in the properties of powdered iron. Also, that there is only a limited quantity of powdered iron available having certain specific properties in which we are at the moment interested. F. P. Peters.—May I have a word? With all possible respect to the contributions of the Chrysler Corporation (and they have been tremendous) to the war effort, I think it is easy to get from part of Mr. Langhammer's discussion a false impression of vaster possibilities than really exist. It would be well if in addition to Mr. Langhammer some other manufacturers of machine parts' might tell us in the next few minutes some of the limitations they have found. For example, what is the maximum tensile strength that is being produced in a commercial part in production today? And what is the actual size limitation on bearings that are in operation and are standing up well? We should always bear in mind the fact—and I think Mr. Langhammer will agree with me— that quoting on a particular part does not necessarily mean placing it in production. In many cases it may be several months before the quotation is resolved and we know whether the part can be made. Let us open up this thing for a little free-for-all discussion of some of the ceilings that do exist in the design of machine parts made by powder metallurgy. The ceiling is not unlimited, and Mr. Langhsmmer will agree with that, 3 am sure. H. Hendriks.*—I do not think that there is so much limitation in the making of powder metallurgic manufactured parts as mentioned. Last year we had the problem of making dies for a special machine used in the manufacturing of slide fasteners. This part was wearing out very fast. It was very hard to make, it had to be hobbed out of a special steel and it was a difficult thing to manufacture in general. The tolerances were one half of one thousandth of one inch on all dimensions. We submitted this die to a manufacturer of powder-metal parts. He thought that it was impossible, but we were not as skeptical as he was and decided to try it anyway. The Canadian General Electric Carboloy Division, in Toronto, gave us then the design for the dies, which we made to their specifications. When the first part was delivered, we submitted it to our Inspection Department and its check showed that all the tolerances were right on the dot. They delivered I9 parts of exact specification, then they went off the beam; they could not keep to the tolerances. It took them a long time to get back again. We do not know what happened, but the main point I want to' make is that if a problem is attacked in the right may, the dies are made right and corrected as to dimensions found out by experiment, I do not think that there is so much diffculty in making powder-metal parts to close tolerances.

Jan 1, 1945

By Milton E. Wadsworth, John N. Ong, W. Martin Fassell

The temperature and oxygen concentration dependence on the reaction of sphalerite in oxygen at pressures from 6 to 640 mm Hg have been investigated in the temperature range 700° to 870°C. Sphalerite has been found to oxidize linearly over this entire temperature and pressure range. At higher rates, considerable self-heating was observed. The dependence of the oxidation rate on the oxygen concentration may be expressed by: Rate = k' where k' is the specific rate constant and 0 = K1[O2]/(1 + KI[O2]), where K1 is the equilibrium rate constant for the adsorption of oxygen on sphalerite. Values of the activation energy and the enthalpy of adsorption were found to be 60.3 and —59.6 kcal per mol, respectively. Data have been presented that indicate conditions under which either a sulphatizing or an oxidizing roast may be obtained. ROASTING processes have been employed in the metallurgy of a great number of basic metals in use today. Until recently, however, little attempt has been made to deduce the fundamental mechanism by which oxidation takes place. Structural changes upon oxidation have been investigated1 = and thorough work has been performed with regard to the reaction products and the thermodynamics of the oxidation reactions. The objective of this investigation was to determine the rate of oxidation of sphalerite and to apply the absolute reaction rate theory in the theoretilcal interpretation of the experimental results." "O Description of Apparatus The apparatus contains the following features: 1—a furnace with gas system, 2—an autographic weighing system, and 3—a temperature control system. Furnace With Gas System—The furnace was mounted by a yoke on each end and was free to travel up and down on steel guide rods, permitting the introduction and removal of samples from the apparatus with minimum difficulty. The furnace was heated by three sections of Kanthal wire wound externally on a zirconia tube and insulated with Fiber-frax. Pure gases or mixtures of gases were introduced into the lower end of the furnace through two flowmeters, a mixing chamber, and a gas-tight sparger, Fig. 1. The gaseous products of the reaction and the unused gases were prevented from escaping to the atmosphere by maintaining a small negative pressure on the system. This procedure permitted air from the outside to enter through the small an-nulus around the quartz suspension fiber and prevented the escape of the internal gases. Autographic Weighing System—The autographic weighing system consisted of an adapted gold balance, a photoelectric circuit, and a weight recorder, Fig. 2. The sample was suspended from one end of the balance beam by means of a platinum chain outside the furnace and a long thin quartz fiber on the inside of the furnace. On the other end of the balance beam, the necessary weights were added to counterbalance the sample. In addition, a calibrated chain was added to the balance which was linked directly to the weight recording unit. Control was effected by means of a photoelectric circuit." A parallel beam of light from a strong source was directed onto a small front-surfaced aluminum mirror mounted in the middle of the balance beam and then to a front-surfaced mirror mounted on the ceiling of the room. The beam was then reflected onto a front-surfaced right prism at a distance of 9 ft from the balance

Jan 1, 1957