Search Documents

By C. S. Smith, K. K. Ikeuye

In an earlier paper1 one of the authors called attention to the significance of the relative free energies of grain boundaries and interphase boundaries in alloys in determining the shape and distribution of micro-constituents. The ratio of the interphase and inter-crystalline boundary energies (that is, —?12, where ?12 is the energy of the interface between a crystal of phase 1 and a crystal of phase 2, and ?11 is the energy of the boundary between two crystals of phase 1) will be denoted by F. It is this ratio that determines, by the simple triangle of forces relation, the dihedral angle, ?, of phase 2 where it adjoins a boundary between two grains of phase 1. On a metallographic sample various angles are actually obtained because of the random orientation of the plane of observation, but the statistically most frequent angle is the true one. These basic principles were discussed in detail in the earlier paper. The experiments described below show the effect of both composition and temperature on ? and T for some alloys containing a liquid phase, and provide data on the rate of approach to the equilibrium angles in both solid and liquid phases. All the alloys were melted in a graphite crucible and cast into ingots 3/4 by 11/8 in. cross-section. Some of the aluminum alloys consisted of two immiscible liquids from which uniform castings could not be obtained. The amount of liquid phase varied locally to a considerable extent and the analyses were meaningless. Nevertheless, the composition of the liquid would not differ from that in an alloy of the intended gross composition, and the synthetic composition of the alloys was therefore used in considering the surface energy results. The ingots were given initial deformation by cold-rolling to 50 pct reduction, annealed, and given a second 50 pct reduction prior to cutting into small samples for heat treatment at the times and temperatures subsequently reported. The resulting micro-samples were carefully prepared metallographically and examined at magnifications of 650, 1280, or 2500. The objectives used were 21X, 0.40 NA (dry); 41X, 0.65 NA (dry); and 80X, 1.40 NA (oil emulsion). The appropriate angles were measured by rotation of the stage of a Bausch and Lomb metallograph to align the appropriate boundaries successively with a cross-hair in a micrometer eyepiece. About 250 angles were measured on each phase. Though the angles were read to 1°, the accuracy is probably not above 3°, because of uncertainty in setting the cross-hair tangent to the sometimes curved boundary. The corners of very small particles, particularly in early stages of adjustment after cold-rolling, were difficult to measure and the results were slightly dependent on the magnification used (compare Fig 1-C and 1-D). With particles of larger size and more nearly equilibrium shape, magnification made no difference (vide Fig 1-F and 1-G). The measured angles were grouped in 10° intervals (5° if ? was less than 20°) and plotted in bar

Jan 1, 1950

By W. O. Philbrook, K. M. Goldman, G. Derge

T. Rosenqvist—The most interesting point in this paper is the observed transfer of iron into the slag in the initial stage of the desulphurization process, after which the iron again is reduced to the metallic state. The authors interpret this observation as showing that the sulphur enters the slag as an iron-sulphur compound which subsequently is decomposed by the slag. The present writer has previously suggested the following equation for the desulphurization process: S + O2- ? S2- + O For equilibrium in the blast furnace the oxygen potential is defined by equilibrium with graphite and CO of 1 atm pressure: C + O ? CO [2] During the desulphurization process the reactions proceed in the direction of the arrows. If one assumes eq 2 to be significantly slower than eq 1, the transfer of sulphur into the slag, in accordance with eq 1, will build up a local oxygen potential at the metal-slag interface very much higher than that corresponding to the value defined by eq 2. This is possible because the equilibrium oxygen potential in eq 1 is high as long as the sulphur content in the slag is low. This oxygen potential will again be able to oxidize some iron: Fe + O ? Fe2+ + O2- and an increase in the iron content of the slag will be observed. Adding up eqs 1 and 3 one obtains: S + Fe ? S2- + Fe2+ The net effect is thus in harmony with the experimental observation but is obtained without assuming any close ties between the sulphur and iron atoms during the process. Furthermore, it follows from eqs 1 and 2 that when the sulphur content in the slag increases, and equilibrium with C and CO is finally approached, the local oxygen potential at the metal-slag interface will decrease, and the iron in the slag will be reduced back into its metallic state. C. E. Sims-—The data and conclusions presented in this paper are thoroughly convincing in establishing the mechanism of sulphur transfer from iron to slag as in a blast furnace. The evolution of gaseous CO in step 3 of the reactions given on p. 1112 makes the process virtually irreversible. Assuming that the process is similar in slag-metal systems other than in the blast furnace, it is readily seen why free CaO and re-ducing conditions so greatly favor desulphurization. On the other hand, the very effective desulphurization obtained in oxidizing slags when strongly basic, must be attributed to the relatively high stability of CaS as compared to FeS. The ease and simplicity with which the reactions of classic chemistry agree with the experimental data and explain the mechanism is noteworthy. The concept of molecules of FeS, soluble in both phases (metallic iron is not soluble in the slag), migrating from the iron to the slag and there reacting with CaO, which is soluble only in the slag phase, is clear and uncomplicated. This is likewise true for step 3. Those who would deny the existence of molecules or molecular-type combinations in liquid iron, must strain to provide a mechanism so lucid. In the absence of molecules, the Fe and S exhibit a remarkable collusion. L. S. Darken—The investigation and interpretation of rate phenomena in the range of steelmaking temperatures is a difficult task. Most of the laboratory investigations of steelmaking reactions have been concerned with equilibrium. Having determined the equilibrium, our attention naturally focuses next on the mechanism and rate of approach to equilibrium. The authors seem to have contributed substantially to our understanding of these factors for the case of sulphur transfer. I should like to ask the authors whether they consider that the sulphur transfer reaction is diffusion controlled as many high-temperature reactions seem to be. If so, it would seem reasonable to suppose that the slow diffusion step of the process is the transfer across a pseudo-static layer or film similar to that considered in heat flow problems. As the diffusivity and fluidity are smaller for the slag than for the metal, it may tentatively be assumed that the sulphur gradient exists in a thin layer in the slag adjacent to the slag-metal interface and that the metal and the main mass of slag are each maintained uniform by convection. On this basis the amount of sulphur transferred across unit area per unit time is D p (?S%)/100 ?1, where D is the diffusivity, p the density, (?S%) the difference in percent sulphur on the two sides of the layer, and ?l is the layer thickness. At the beginning of the experiment the main body of the slag and hence one side of the layer contains no sulphur; therefore (?S%) may be replaced by (S%), the sulphur content of the slag at the slag-metal interface, which in turn is equal to L[S%] where [S%] is the sulphur content of the metal and L is the distribution coefficient. The rate of transfer thus becomes DpL[S%]/100 ?l, which the authors designate K[S%]. Equating these two quantities and setting D = 10-6 cm2 per sec, p = 3 g per cm3, L = 40, and K = lo-+ g cm-2 sec-1, it is found that ?l, the film thickness, is about 0.01 cm—a value of the order of magnitude of that found in heat transfer problems in liquids. The uncertainty of the numerical values used leaves much to be desired, but at least it can be said that this calculation tends to support the proposed model involving diffusion through a film. Although this does not seem to affect the general argument, I should like to call attention to the fact that the diffusivity3 of sulphur in hot metal is found (on conversion of units) to be about 10-4 cm2 per sec rather than 104 cm2 per sec as stated by the authors. The three equations written by the authors to express the steps in the overall process of sulphur transfer may alternatively be written ionically as only two Fe + S = Fe++ + S-- Fe++ + O-- + C (graphite or metal) = CO (gas) + Fe where the underscore is used to designate the metallic phase; ionic species are slag constituents. After the authors have so neatly demonstrated that iron and sulphur transfer together (at least initially), this fact seems almost self evident; from eq 4 it is seen that if sulphur acquires a negative charge during transfer

Jan 1, 1951

By J. Weertman

The paper of Gifkins and Snowden considers the interesting but difficult problem of determining the stress dependence of secondary (steady-state) creep at low stresses. These authors have concluded that at stresses below 250 psi (2 x 107 dynes per sq cm) the secondary creep rate of lead is proportional to the stress (viscous creep) and is not proportional to the stress raised to about a fifth power. The experimental data considered by them were obtained on tests conducted at room temperature and at 50°C. The lowest stress employed was 50 psi (3.5 X 106 dynes per sq cm). The authors pointed out the main difficulty in determining the stress dependence of creep at low stresses. The creep tests must be run for very long lengths of time. However they made no estimates of when an experimental creep rate determination must be rejected because it does not represent a true steady-state or minimum creep rate. In order to be certain that a creep curve is within the steady-state region, the total creep strain should be of the order of 0.1 to 0.2. For a creep test of a year's duration this requirement implies that a secondary creep rate smaller than about 10-3 per hr cannot be measured reliably. The corresponding creep rate for a 10-year test is 10-6 per hr. The creep rates of the tests that were considered by the authors to prove the existence of viscous creep were of the order of or less than 10-6 per hr. One can conclude reasonably that this data does not prove unambiguously that large strain steady-state creep rate of lead is proportional to the stress in the stress range of 50 to 250 psi (3.5 x 106 to 2 X 107 dynes per sq cm). Another technique can be used to obtain the stress dependence at low stress levels. The creep rate is a very sensitive function of temperature. The creep rate can be increased by very large amounts merely by increasing the temperature. We carried out steady-state creep tests on lead single crystals25 at temperatures up to 320°C. We were able to obtain creep rate data down to stresses as low as 35 psi (2.5 x 10' dynes per sq cm). Our smallest creep rate was 8 x 10-5 per hr. Thus we obtained large strain, steady-state creep rates to even lower stresses than were considered by Gifkins and Snowden. No evidence was seen for viscous creep. The creep rate was proportional to the stress raised to about a 4.5 power down to the lowest stresses. Since there is no reason to believe that changing the temperature should change the stress dependence of steady-state creep, we feel that large strain viscous creep does not occur in the stress range quoted by the authors for lead single crystals or large-grain polycrystalline samples of lead. This conclusion does not imply that viscous creep may nat occur in a lower stress range or in the same stress range for fine grain material or at creep strains very much smaller than 0.1. Support by the U.S. Office of Naval Research is acknowledged. Authors' Reply R. C. Gifkins and K. U. Snowden We thank Dr. Weertman for his discussion and although, as we hope to show, we do not agree with his reservations, we do concur in stressing the importance of ensuring that creep rates are reliably obtained. Dr. Weertman appears to be content to accept n = 1 for low stresses with fine-grained material but not for single crystals. We believe our results show that the former result cannot be accepted without also accepting the latter. We will also show that the probable errors in our minimum creep rates are insufficient to alter our conclusions, that the criterion proposed by Dr. Weertman is arbitrarily restrictive and his alternative experimental approach possibly invalid. 1) A principal result of our Fig. 1(a) is that n = 1 for polycrystalline specimens at room temperature and 50°C for stresses below -250 psi. There was evidence that crystal slip and grain boundary sliding contributed approximately equaily to the overall strain in this low-stress regime. This implies that either a) grain boundary sliding controls slip within the grains or b) both grain boundary sliding and crystal slip independently occur according to mechanisms which give n = 1. Alternative a does not seem acceptable, so we were forced to consider b. This led us to reexamine work on bicrystals by Strutt and Gifkins and plot curves Fig. l(b). Previously Strutt et al. (loc. cit.), had merged these points with others using the Zener-Holloman parameter and thus, we now believe, had been led to overlook the behavior where n = 1. Curves C and D in Fig. l(b) did appear to confirm the hypotheses that n = 1 for crystal slip at these low stresses and the sliding curve F was similarly of the expected form. It was comparatively easy to find a quantitative theory to account for n = 1 for sliding and the similarity of curves C and D to curve F (all obtained from the same set of specimens) led us to feel that the single-crystal curves were valid. 2) We believe the secondary creep rates for both the polycrystalline and single-crystal specimens to be in error by factors c2. In Fig. 6 creep curves for polycrystalline specimens of lead(1) and lead(II) are reproduced as curves a and b, respectively, and curve c is for a single crystal at 100 psi. It is clear that, although the attainment of secondary creep rate takes 2 years for a and 150 days for b, thereafter the curve is linear for periods of 7 and -1 year, respectively. The single crystal has a linear portion commencing after 20 and extending to 90 days. Creep extension was measured directly using a traveling microscope reading to 0.01 mm on gage lengths marked on the specimens; the gage lengths

Jan 1, 1968

Executive SIDNEY J. JENNINGS, Chairman GEORGE D. BARRON J. E. JOHNSON, JR. EDWIN LUDLOW ROBERT M. RAYMOND Membership KARL EILERS, Chairman LEWIS W. FRANCIS J. E. JOHNSON, JR. LOUIS D. HUNTOON ARTHUR L. WALKER Finance GEORGE D. BARRON, Chairman CHARLES F. RAND BENJAMIN B. THAYER Library E. GYBBON SPILSBURY,1 Chairman ALEX C. HUMPHREYS3 GEORGE C.' STONE2 J. H. JANEWAY4 BRADLEY, STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 7, 1918

Executive SIDNEY J. JENNINGS, Chairman GEORGE D.-BARRON J. E. JOHNSON, JR. EDWIN LUDLOW ROBERT M. RAYMOND Membership KARL EILERS, Chairman LEWIS W. FRANCIS J. E. JOHNSON, JR. LOUIS D. HUNTOON ARTHUR L. WALKER Finance GEORGE D. BARRON, Chairman. CHARLES F. RAND BENJAMIN B. THAYER Library E. GYBBON SPILSBURY,1 Chairman ALEX C. HUMPHREYS3 GEORGE C. STONE2 J. H. JANEWAY4 BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 9, 1918

By G. Vaux, M. L. Fuller

AN apparatus and procedure for the determination by X-ray reflection of preferred orientation of crystals in rolled metal with the Geiger counter X-ray spectrometer was described by Schulz.' This is an excellent procedure and we have used it continually for several years. In our use of the procedure, two modifications have been made and used during most of this period. One of these provides for automatic scanning and recording of the reflections, and the other makes possible the application of the procedure to coarse-grained specimens and permits measurement of almost all orientations without resort to the transmission technique. The automatic scanning and recording are accomplished by a motor drive of the inner ring of the Schulz apparatus (see R, in Fig. 2 of his paper and R2 in Fig. 1 of this note) in synchronism with the chart recorder of the North American Philips 90" X-ray spectrometer. A rate of 10" per min is used. A scan of 180" is obtained corresponding to poles on the stereographic projection whose locus is a great circle. The modification for coarse-grained material is accomplished by allowing a larger area of the specimen to contribute to the X-ray diffraction. In the Schulz apparatus the incident X-ray beam is confined by a slit system to rays in the plane of the spectrometer. Schulz demonstrated that this restriction of the X-ray beam permits a survey of the X-ray reflections without correction up to about 80" on either side of that specimen position in which the specimen is perpendicular to the plane of the spectrometer. This is the angle + of rotation of the inner ring R2. One of these slits is horizontal and extends across the X-ray source side of the specimen. In the modification this slit is removed, thus permitting greater divergence in the X-ray beam and the irradiation of a larger area of the specimen surface. Fig. 1 shows the apparatus with the motor drive and with the slit removed. Discontinuities in the recorded X-ray intensity plot due to the few participating crystals in coarse-grained metal are much lessened. The increased divergence does not cause reflections from other crystal planes to enter the Geiger counter slit. An important advantage of the original Schulz scheme is thus lost and a system for correction is required. To do this, a compact of atomized copper powder was prepared and tested by the original Schulz method for the absence of preferred orientation. The horizontal slit was then removed and a curve recorded showing the variation of intensity with angle +. In our arrangement the intensity was uniform within the range + equals ±30°. Beyond this the intensity fell off rapidly reaching zero at ±90°. The curve thus produced is then used to correct measurements made on preferred orientation specimens. In practice this is accomplished by constructing from this calibration curve a family of curves which, as a transparency, can be superimposed on the recorder chart to read corrected intensity directly. Not only does this method permit the handling of coarse-grained material but it also makes possible the plotting of intensities almost to the circumference of the stereographic pole figure projection. Thus, nearly the entire pole figure can be plotted without the necessity of using the transmission technique. Moreover, intensities are much greater, an advantage when surveying crystal planes of poor reflecting power.

Jan 1, 1954

Executive SIDNEY J. JENNINGS, Chairman GEORGE D. BARRON J. E. JOHNSON, JR. EDWIN LUDLOW ROBERT M. RAYMOND Membership KARL EILERS, Chairman LEWIS W. FRANCIS J. E. JOHNSON, JR. LOUIS D. HUNTOON ARTHUR L. WALKER Finance GEORGE D. BARRON, Chairman CHARLES F. RAND BENJAMIN B. THAYER Library E. GYBBON SPILSBURY,1 Chairman ALEX C. HUMPHREYS3 GEORGE C. STONE2 J. H. JANEWAY4 BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 11, 1918

By James P. Savely, Victor L. Kastner

Inspiration Consolidated Copper Company is currently mining in four pit areas; Live Oak, Red Hill, Thornton and Joe Bush Extension, near Globe, Arizona. Small satellite orebodies lying outside the main pits have been mined out in a series of small open pits. Major slope instability has affected production in every pit. Some consequences of the instability have been; (1) Serious interruption of mining plans, which resulted in deferred ore production, lost ore, reduced mining rates and increased stripping requirements. (2) Forced replacement of crushing facilities. (3) Serious effects on other production facilities. The introduction of a slope stability monitoring and control function as an integral part of mine planning has been successful in reducing the impact of these failures and will eventually result in economic pit design based on probabilistic slope analysis. This case history presents a brief review of the problems associated with slope instability at Inspiration's mines followed by a more detailed report on one specific failure area in the Thornton pit where the use of horizontal drain holes for slope stabilization appears to be successful. Relationships between slope movement rate, rainfall, and mining activity are shown.

Jan 1, 1983

By C. K. Leith

THE purpose of these conferences has been to find some basic principles to guide us in the chaos which confronts us, to arrive at elements of a national policy. None such exists, nor, as a matter of fact, have there been any concerted efforts by the public or the mineral industry to evolve one. In the absence of such a policy the administrative agencies of the government can hardly be expected to be consistent or really effective in their handling of mineral problems, domestic or foreign. Basic Facts MINERAL reserves are unequally distributed among the nations. The principal world supplies are grouped around the north Atlantic, and nearly three-fourths of the world's total is controlled politically and commercially by English-speaking people. No one nation has a complete supply of the minerals necessary for modern industry; specialization, reciprocity, and large-scale movements between the nations are inherent in nature's unequal distribution of them. The principal sources of supply are relatively few compared with the nations to be served-a fact which determines broadly certain natural outlines of the world flow. National isolation with regard to minerals can be accomplished only through backward steps in industry and lower standards of living even in the nations possessing the most of the mineral supplies. A certain measure of unified commercial control, international in scope, is a natural consequence of the limited number of the large sources of supply. Mineral supplies for the world as a whole are so large that there is little need for concern about early exhaustion, but every nation has important problems of early exhaustion of particular minerals, which must affect their policies.

Jan 1, 1933

By J. L. Rodda, R. L. Wilcox, E. C. Truesdale

In recent years various problems in connection with research work on the preparation and properties of zinc-base alloys have required reliable information concerning the constitution of the zinc-rich portion of the iron-zinc equilibrium diagram. On numerous occasions rather positive indications were obtained that, for example, the solubility of iron in zinc was incorrectly represented on the current equilibrium diagrams. A careful study of all the available literature relating to the iron-zinc system led to the conclusion that much of the early work was unsatisfactory as measured by present standards of experimental accuracy, and as a result it was decided to redetermine the location of the liquidus curve and of adjacent portions of the diagram. Part I of this paper comprises a description of the experimental methods and a summary of the results by means of which the zinc-rich end of- the iron-zinc diagram has been revised in the following ways: 1. Measurements of the solubility of iron in liquid zinc by several different sampling methods, leading to a relocation of the liquidus curve. 2. Microscopic, conductivity, and X-ray studies of the solid solubility of iron in zinc, which, together with thermal analyses, have resulted in new values for the solid solubility and the eutectic temperature and composition. 3. Heating and cooling curves, obtained by a refined differential method, leading to new locations for the two peritectic horizontals. In Part I1 of the paper the attempt is made to review all of the published work having a bearing on the constitution of the iron-zinc system, and to correlate the present results, and some recently published data involving the use of X-ray technique, with the earlier work, much of which was done from 25 to 30 years ago.

Jan 1, 1936

Executive SIDNEY J. JENNINGS, Chairman GEORGE D. BARRON J. E. JOHNSON, JR. EDWIN LUDLOW ROBERT-M. RAYMOND Membership LEWIS W. FRANCIS KARL EILERS, Chairman J. E. JOHNSON, JR. LOUIS D. HUNTOON ARTHUR L. WALKER Finance GEORGE D. BARRON, Chairman CHARLES F. RAND BENJAMIN B. THAYER Library E. GYBBON SPILSBURY.1 Chairman. ALEX C. HUMPHREYS3 GEORGE C. STONE2 J. H. JANEWAY4 BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 2, 1919

Executive SIDNEY J. JENNINGS, Chairman. GEORGE D. BARRON J. E. JOHNSON, JR. EDWIN LUDLOW ROBERT M. RAYMOND Membership KARL EILERS, Chairman LEWIS W. FRANCIS J. E. JOHNSON, JR. LOUIS D. HUNTOON ARTHUR L. WALKER Finance GEORGE D. BARRON Chairman CHARLES F. RAND BENJAMIN B. THAYER Library E. GYBBON SPILSBURY,1 Chairman ALEX C. HUMPHREYS3 GEORGE C. STONE2 J. H. JANEWAY4 BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 6, 1918

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2'3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2'3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

(The following-list contains the names of those members of the Institute of whose connection with military service we have only recently. become acquainted.) ADAIR, ARTHUR C., Corporal, 4th Co., 1st Tr. Bn., 154th D. B., Camp Meade, Md. BATCHELOR, STILLMAN, 1st Lieut., Co. 6, E. 0. T. S., Camp Humphreys, Va. BATES, BENNETT R., 1st Lieut., Engineers, Co. 3, E. 0. T. S., Camp Humphreys, Va. BJORGE, GUY N., Co. 3, E. 0. T. S., Camp Humphreys, Va. BOAS, Ross, H., U. S. A. BRADLEY, . H., JR., Capt., 408th Engineers, Camp Cody, N. M. BRINTON, OWEN F., Capt., Engineers, U. S. A. BROWN, HAROLD C., 2d Lieut., A. S. A.P.

Jan 1, 1919

By J. C. Mertz, C. H. Mathewson

Accurate knowledge of the solid solubilities of the elements that dissolve in the important base metals is needed for guidance in the preparation and heat-treatment of the alloys derived from these components. While there is still difference of opinion concerning the merits of the X-ray and microscopic methods of determining such solubilities, it is certainly true that the recent extensive use of X-ray diffraction to review the existing constitutional data has revealed many glaring inaccuracies and has brought about a much improved knowledge of phase-boundary locations, which will inevitably come to include all of the important alloy systems. When the work is done with all necessary precautions it appears that in the majority of cases where the solubilities extend beyond a few tenths of a per cent the X-ray back-reflection technique is capable of furnishing the best of information in this field. For the most prolonged and thorough studies it is obviously advisable to combine the results of several methods, in particular, to obtain an agreement between X-ray and microscopic data. This paper reviews the work previously done on the solubilities of phosphorus, arsenic, antimony and bismuth in copper and, in consideration of the uncertainties thus made apparent, presents new X-ray data obtained with the first three members of this group. Copper-phosphorus System Heyn and Baurl found that in slowly cooled alloys phosphorus forms a solid solution with copper up to about 0.175 per cent. Huntington

Jan 1, 1937

By Terkel Rosenqvist

THE desulphurization of molten iron and steel is a very complicated process. One way to arrive at a better understanding of this process is to break it down into several simpler chemical processes that can be studied individually in the laboratory. For a study of the different factors that influence the equilibrium distribution of sulphur between liquid metals and slags, several simpler equilibria may be investigated. One very important subject is the determination of the escaping tendency of sulphur in the liquid metal and its dependency on temperature and composition of the melt. Several papers in this field have recently been published.', ' Another subject is the study of the sulphur capacity of the slag. A molten slag is indeed complex, and even if sulphur distribution data for a large variety of molten slags may give empirical data about their desulphurizing power, the importance of the individual components is still not quite clear. It is accepted generally that lime is the most important desulphurizing component in the slag. The present investigation has as its purpose to study the desulphurizing power of lime in its standard state, and to provide a basis for thermodynamic calculations of the desulphurizing power of various lime-containing slags. The standard state of lime at steelmaking temperatures is solid calcium oxide, CaO. It can react with sulphur to form solid calcium sulphide, CaS. The relative stability of calcium oxide and calcium sulphide is expressed by the free energy of the reaction: 2Ca0 (s) + S1 (g) = 2CaS (s) + O2 (g) The existing free energy data for this reaction, listed by Kelley5 nd Osborn,' are uncertain to about 10 kcal and are of limited value for a calculation of equilibrium constants. Under the conditions prevailing in a melting furnace, the sulphur pressure may be expressed conveniently by the ratio H,S/H2 and the oxygen pressure by the ratio H,O/H, (or CO,/CO). The desulphurizing power of calcium oxide may, therefore, be studied by the reaction CaO + HIS = CaS + H2O. A study of this reaction may be complicated by certain side reactions: Water vapor and hydrogen sulphide may react. to form sulphur dioxide, and calcium sulphide may be oxidized to calcium sulphate. A thermodynamic calculation shows that these side reactions will be suppressed to insignificance if the equilibrium is studied in the presence of an excess of hydrogen. The apparatus used is shown in Fig. 1. About 10 g calcium oxide and 20 g calcium sulphide (laboratory qualities) were intimately mixed, and some water was added to make a thick paste. The paste was put into a thimble of zirconium silicate, which was placed within the constant temperature zone of a furnace, and capillary refractory tubes were attached in both ends. After the mixture had been heated in dry hydrogen at 1000°C for several hours all Ca(OH), and CaCO, had decomposed and CaSO, was reduced, so only CaO and CaS remained in the thimble forming a porous plug. The mixture was examined by X-ray diffraction after the initial reduction in dry hydrogen as well as after the subsequent experimental runs up to 1425 °C. It was shown that crystalline calcium oxide and calcium sulphide were always present together in about equal amounts. The unit cell edges were found to be 4.80A for CaO and 5.68A for CaS in good agreement with existing literature values." This shows that the mutual solid solubility is very small, and that the compounds are present in their standard states. Purified hydrogen was passed through water sat-urators kept at constant temperature in a thermostat bath. The amount of water vapor saturation was checked by means of a dew point method, not shown on Fig. 1. The gas mixture was passed through the capillary inlet into the furnace, where it was sifted through the porous plug of calcium oxide and calcium sulphide. The hydrogen sulphide present in the outgoing gas was absorbed in a zinc acetate solution and the hydrogen was collected over water. When one liter of hydrogen had been collected, the amount of hydrogen sulphide was determined by iodometric titration. As one molecule of H,O is used for the formation of each molecule of H,S, the equilibrium ratio H,S/H,O would be , where (H,O) is the molar concentration in the ingoing gas, and (H,S) the molar concentration in the outgoing gas. In the present work (H,S) was always very small compared to (H20). In order for the observed H,S/H20 ratio to represent the true equilibrium ratio the gas flow has to be: 1—Sufficiently slow to give a complete establishment of equilibrium, and 2—sufficiently fast to counteract thermal diffusion. Incomplete reaction would give a value decreasing with increasing flow rate, and thermal diffusion would give a value increasing with decreasing flow rate. When inlet and outlet tubes of about 2 sq mm cross-section were used, the observed gas ratio was independent of the flow rate between 15 and 125 cc per min, Fig. 2. In this range, therefore, the observed gas ratio represents true equilibrium.* For the rest of the in-

Jan 1, 1952

By JAMES J. PURDY

The great majority of stokers used in residential heating installations are of the clinkering type. Because of inherent characteristics of the under- feed combustion process as it occurs in these small stokers, and because of the wide range of operating conditions encountered in residential heating schedules, not all bituminous coals can be used successfully in residential underfeed units. The problem of providing consumer satisfaction has been attacked by the joint efforts of the stoker manufacturers and the coal industry; the stoker manufacturers have been concerned with improving their product to permit the use of a wider range of coals, and coal operators have made every effort to market selected and better prepared coals. In view of the wide range of physical characteristics and chemical properties of bituminous coals, the problems are real and are receiving increased attention.

Jan 1, 1949

By M. Guney, A. R. Bell

In Mindola mine on the Zambian Copperbelt, there is a plan to extend the current production level of 1.2- 1.5 km (3,900-4,900 ft) with five additional production levels. Research work indicated that the present total heat output of 38.6 MW will inevitably increase to 63.2 MW in 25 years. Estimated WE and DB temperatures, representing the total heat generation in stope faces and development headings during these same periods are predicted to increase to 33.8/40.2°C (93/104°F) and 35.3/42.1°C (95/108°F) respectively. It is assessed that the nominal refrigeration capacity needs to be progressively increased to 9,000 M W.

Jan 1, 1984

By R. Taggart, D. H. Polonis, W. C. Gallaugher

In the Ti-Cu system, the a' phase can be produced over a wide range of alloy composition witJwut the retention of measurable amounts of the ß or ? phases. This paper reports on the decomposition of this hexagonal martensite phase front the standpoint of solute corzcentratiorz, tempering temperature, and coherency strain condition. The mechanism of precipitation during tempering comprises localized precipitation which is followed by discontinuous precipitation if sufficient coherency strains are present. The localized precipitation process in hypoeutectoid alloys is described by the generalized Johnson-hiehl equation and an activation energy of 46,000 cal per mole. In hypereutectoid alloys the corresponcEing activation energy is 51,000 cal per mole. The rate-controlling process has been proposed as the difision of copper along a' platelet interfnces. SEVERAL investigations have been reported concerning the kinetics of decomposition of the mar-tensitic a' phase in titanium binary alloys.' In the Ti-Mo system,' two modes of a' decomposition have been observed in the presence of /3 phase; one of these involves the precipitation of fine a from a', and the other involves diffusion across the a'-ß interface. In studies of the Ti-Cr system, Rostoker2 did not detect the formation of TiCr2 during tempering. In Ti-Ni alloys,3 the intermediate phase Ti2Ni has been found to precipitate directly from a' along the interfaces between plates. With the exception of the study of Ti-Ni alloys the previous investigations of tempering phenomena in substitutional martensites are mainly qualitative and do not present a detailed description of the precipitation processes. The following limitations restrict the correlation of the microstruc-tural processes and reaction kinetics during tempering in most binary-alloy systems. 1) A mixture of at least two phases characterizes the constitution of quenched alloys. 2) Difficulties have been encountered in obtaining uniform structures throughout quenched samples. 3) The reaction products, and in particular their morphology. have not been clearly resolved. 4) The martensitic a' phase forms over only a limited composition range for most titanium-base binary alloys. Gomez and polonis4 showed that the Ti-Cu system provides an excellent basis for investigating the tempering of a' over a range of composition without the complication of retained P or the transition w phase. In the present work the effects of solute concentration, tempering temperature, and coherency strain conditions are considered with reference to the over-all precipitation process in quenched alloys of the Ti-Cu system. Both microstructural observations and kinetic data are correlated to define the rate-controlling processes which govern the observed localized and discontinuous precipitation reactions. An earlier paper5 was devoted to a discussion of the modes of heterogeneous nucleation of Ti2Cu from the martensitic a' structure. The present paper will therefore emphasize the progress of the tempering reaction beyond the initial stages. EXPERIMENTAL METHODS The Ti-Cu alloys for this study were prepared by conventional arc-melting procedures. Chemical analysis revealed that the alloy buttons contained approximately 0.02 wt pct 0, 0.04 wt pct N, and within 0.1 wt pct of the intended copper concentration. The progress of the tempering reaction was followed by means of electrical-resistance measurements utilizing a Kelvin double bridge, microhard-ness readings with a 400-g load, and X-ray dif-fractometry patterns to reveal line-broadening effects. Metallographic specimens examined at magnifications greater than X1000 were shadowed with germanium to reveal fine structural details. Direct carbon replicas were prepared for the electron-microscopy studies. EXPERIMENTAL RESULTS Property Changes. The changes of microhardness that accompany the precipitation of Ti2Cu from a' are shown in Figs. 1 and 2. As the solute concentration increases the peak hardness, for a given tempering temperature, increases. In alloys of given composition the time to reach the peak hardness agreed with the time to attain maximum X-ray diffraction peak breadth, as shown in Fig. 3. The maximum hardness and the maximum line breadth increased with lower tempering temperatures, and the time to reach the maximum also increased. The a' peaks broadened during the initial stages of tem-

Jan 1, 1965