Search Documents

By Laurence Delisle, Aaron Finger

THE alloys formed by the addition of nickel to iron by convelltional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.? owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect could be obtained in alloys of iron and nickel prepared by powder metallurgy technique. PROCEDURE Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, 0.001 5 ; lead, 0.035; tin, 0.025 ; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A representative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 3 2 5-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the surfaces of the particles. The reduced powders, slightly caked, were ground in a mortar and screened again through a 325- mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hydraulic presses. The pellets were compacted in a cylindrical die, ½ in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specifed for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By L. G. Schulz

THE possibility of using reflected X-rays to produce images of crystals was explored by Barrettl who developed simple experimental procedures for X-ray microscopy and who showed by numerous examples the great range of information that could be made available. In his method characteris radiation is used to produce an image of a limited area of the sample on fine-grained film, this image subsequently being enlarged approximately X100. A somewhat different method will be described here;' white radiation from a fine-focus X-ray tube-"' is used to produce an image of a relatively large area of a single-crystal surface. part of the sample; therefore, white radiation is needed. The resolution in the image formed on the photographic film will depend on the size of the focal spot of the X-ray tube. If the sample is made

Jan 1, 1955

The industrial might of the Bowen Basin is primarily the result of Utah Development Co.'s work- which has opened up the Blackwater, Goonyella, Peak Downs, and Saraji mines; built the Hay Point port; and is now developing the Norwich Park mine.

Jan 1, 1977

By William A. Mitchell

AN X-ray diffraction pattern for "calcined cold precipitated ferric oxide" is reproduced dia-grammatically along with data for other iron oxides by R. C. Mackenzie.1' This pattern, which shows spacings higher than those for any other form of iron oxide, was obtained from material prepared and photographed at several different times over a period of weeks, but later attempts to reproduce the results were unsuccessful, the pattern of hematite being obtained every time.2 In an attempt to solve this problem, the original photographs showing the strange diffraction pattern were examined and a marked similarity to the hematite pattern was noticed, suggesting that the pattern was in fact due to hematite but corresponded to a shorter wavelength of X-rays than the Cu Ka which was assumed to have .been used. The eight strongest lines were provisionally identified with the strongest hematite lines and, by means of the corresponding hematite spacings, the X-ray wavelength was calculated for each line. This gave an almost constant value, with the exception of the innermost line which was somewhat diffuse, and confirmed the presence of hematite. The value obtained, 0.703 ± 0.015Å, corresponds to the molybdenum Ka wavelength. The X-ray tube used was a four-filament demountable tube with a copper target. Other photographs, mostly of soil clays, taken during the same period gave normal patterns of Cu Ka radiation with one exception. This was a calcined soil clay with a high iron content and also showed Mo Ka lines of the hematite structure. The explanation is almost certainly that the copper target was contaminated with molybdenum, but it is not known how this occurred. Specimens of alumino-silicates gave their normal Cu Ka pattern, but as the K absorption edge of iron is a little longer than the Cu Ka wavelength, specimens with a high iron content greatly reduced the intensity of the Cu Ka diffraction lines relative to that of the lines due to the shorter Mo Ka wavelength. The formation of hematite on calcining cold precipitated hydrated ferric oxide3 is thus confirmed. References R. C. Mackenzie: Investigations on Cold-precipi-tated Hydrated Ferric Oxide and its Origin in Clays. Problems of Clay and Laterite Genesis, p. 69, Fig. 4, F. AIME Symposium, St. Louis, Mo. Feb. 19-22, 1951. Published 1952. 'R. C. Mackenzie: Ref. 1. Note added on proof. V. C. Hansen and L. T. Brownmiller: Equilibrium Studies on Alumina and Ferric Oxide and on Combinations of These with Magnesia and Calcium Oxide. American Journal of Science (1928) 5, No. 15, pp. 225-242.

Jan 1, 1954

By M. Gensamer

A RECENT paper1 described, by means of stereographic pole figures, the preferred orientations produced by cold-rolling low-carbon steel of automobile-body grade. It was found that the surface of the sheet exhibited a deformation texture significantly different from the texture possessed by the inside of the sheet. Efforts to produce the surface texture by buffing a sample exhibiting the normal or inside texture, using a copper lap, have not been successful. In view of the data collected, by Kurdjumow and Sachs2, it was suggested that the surface texture might be the result of partial recrystallization of the normal or inside texture. The recrystallization texture of cold-rolled mild steel was studied by Goss3, but he did not use the pole-figure method, so that his conclusions were in need of verification. For these reasons the work reported in the present paper was undertaken. It had two objectives: (1) to study the general behavior of cold-rolled mild steel on recrystallization below the critical temperature A,, and (2) to attempt experimentally a demon-stration of the genesis suggested above for the surface texture in cold-rolled steel. The material was that used by Gensamer and Mehl, cold-rolled to 97.5 per cent reduction in thickness. Fig. 1 is an X-ray pinhole photo-gram of this material, taken with the beam transmitted perpendicular to the plane of the sheet, using a molybdenum target at 35 kv. with no filter. It is typical of the inside texture, but in it the deformation texture is better developed than in the samples that showed a well developed difference between the inside and surface samples. Specimens from this sheet, which was 0.005 in. thick, were annealed for 5 min. at various temperatures in a lead bath. After about 0.0005 in. had been etched from both surfaces, X-ray photograms were prepared, using the technique described in the earlier paper'.

Jan 1, 1936

By Leo Tarasov

MAGNETIC torque studies of ferromagnetic single crystals have been carried out in a number of laboratories during the last decade1,2 and some work has been reported on polycrystalline material showing preferred orientation. Goss3 used the method extensively in developing electrical sheet with desirable magnetic properties, but he used it as a control rather than as a means of studying the texture. Bozorth4 made a quantitative correlation of a torque curve he obtained from some cold-rolled iron with the texture as determined from X-rays, but did not extend his studies beyond the one specimen. Other studies, which have been reported from time to time 1.5 have also been incomplete in the sense that no effort was made to study a whole series of samples, differing only in degree of cold reduction, or in the annealing temperature, in order to ascertain the effect of such treatments on the texture as revealed by torque measurements. It is the purpose of this investigation to make such a study, mainly in order to see how useful the method can be made when used under favorable circumstances and to find what kind of a correlation can be expected between magnetic and X-ray studies of texture. Before proceeding further, it is desirable to say a little about single crystals, so as to make clear the concepts involved in magnetic torque measurements.

Jan 1, 1939

By Stephen L. Bolivar, Susan H. Balog, Thomas A. Weaver

A data-classification scheme was developed to detect potential uranium mineralization in the Montrose l º x 2º quadrangle, Colorado. The methodology developed is a rapid and efficient method of resource evaluation on a reconnaissance scale. The necessary techniques were developed and refined to digitize, integrate, and register various large geological, geochemical, and geophysical data sets for the Montrose quadrangle, Colorado, using a grid resolution of 1 km. All data sets for the Montrose quadrangle were registered to the Universal Trans- verse Mercator projection. The data sets include hydrogeochemical and stream sediment analyses for 23 elements, uranium-to-thorium ratios, airborne geo- physical survey data, the locations of 90 uranium occurrences, and a geologic map (scale 1:250 000). Geochemical samples were collected from 3965 locations in the 19 200 km2 quadrangle; aerial data were collected on flight lines flown with 3-5 km spacings. These data sets were smoothed by universal kriging and interpolated to a 179 x 119 rectangular grid (each grid block is 1 km2). A mylar transparency of the geologic map was prepared and digitized. All possible combinations of three, for all data sets, were examined for general geologic correlations by utilizing a color microfilm output. Subsets of data were further examined for selected test areas. A classification scheme for uranium mineralization, based on selected test areas in the Cochetopa uranium district, is presented. Areas favorable for uranium mineralization, based on this scheme, were identified and are discussed.

Jan 1, 1982

By J. S. Ll. Leach, M. B. Bever

THE system copper-nickel exhibits complete solid and liquid miscibility1 The thermodynamic properties of such a system would not be expected to deviate greatly from ideality. Although the evidence is conflicting, anomalies in the composition dependence of various physical properties of solid copper-nickel alloys suggest that mixing may not be ideal.' From measurements of the Hall coefficient it has been concluded that clustering occurs in these alloys. ' Considerations involving the phase diagram of the ternary system copper-nickel-chromium have led Mei-jering3 to predict a positive heat of formation for solid copper-nickel alloys. An electrochemical investigation of the activity of nickel in copper-nickel alloys showed unexpectedly large positive deviations from ideality.4 wagner5 has proposed that if the entropy can be considered ideal, these measurements would yield the following equation for the heat of mixing at 700°C H" = 3380 x,vl (l-xVi) cal per g atom [I1 The heat of formation at 722°C of solid copper-nickel alloys of the equiatomic composition has been measured in a reaction calorimeter as 540 cal per g atom. This note reports calorimetric measurements of the heat effects on dissolution of some copper-nickel ndon: in tin. These measurements were preliminary to a larger investigation, which was later discontinued. From them the heats of formation of the alloys can be calculated, if certain assumptions are

Jan 1, 1960

By Winston A. Wong, John J. Jonas

Commercial purity aluminum was deformed by extrusion over the temperature range 320° to 616°C and the strain rate range 0.1 to 10 per sec. Flow stresses and strain rates were calculated from the experimenLa1 ram pressures and speeds. The stress-strain rate-lemperature relationship in extrusion was found to be similar to that in creep. Extrusion, torsion, compression, and creep data extending over ten orders of magnitude of strain rate and over two orders of magnitude of stress were correlated by a single creep equation. It was concluded that hot-working is a thermally activated process, in which the rate-controlling mechanism is either the climb of edge dislocations or [he motion of jogged screw dislocations. The microstructural changes observed during extrusion were consistent with the proposed deformation mechanisms. ALTHOUGH great progress has been made in understanding the technology of extrusion, very little is known about the actual deformation mechanisms operating during flow. Previous accounts describing extrusion have indicated that the relationship between ram speed (V), pressure (P), and temperature (T) can be given as follows:1 V = apb and P = A' exp(-AT). In these equations, a and b are constants which depend on temperature, A' is a constant which depends on ram speed, and A is a "coefficient" with a different value for each metal. Although these equations have fairly wide application, they do not contribute much to a fundamental understanding of the deformation. Furthermore, extrusion has not hitherto been considered as a thermally activated rate process. This lacuna is surprising because hot-working is similar to high-temperature creep in several respects. There is, in fact, a fair body of experimental evidence suggesting that the material response under hot-working conditions is similar to that occurring under creep conditions, in spite of the many orders of magnitude difference in strain rate.2"4 Since creep has been extensively analyzed in terms of dislocation mechanisms, the comparison of hot-working to creep is useful, for it can suggest the possible deformation mechanisms operating during hot-working. In this paper, the hot extrusion of aluminum will be examined from the point of view of thermally activated deformation mechanisms, such as operate during creep. EXPERIMENTAL PROCEDURE The experimental procedure consisted of extruding commercial purity aluminum* over a range of ram velocities and temperatures at constant die reduction by the direct method. Details of the experimental equipment have been published elsewhere.5 Extrusion was carried out at each of the following billet temperatures: 320°, 376°, 445°, 490°, 555°, and 616°C at the following constant ram speeds: 0.002, 0.008, 0.02, 0.1, and 0.2 in. per sec.* All results were obtained using a square-shouldered die with an extrusion ratio of 40:1, giving a reduction in area of 97.5 pct. The ram force was the dependent variable, and was measured by means of strain gages on the ram and was plotted as a function of ram travel. The sequence of events before making an extrusion was duplicated before each run so as to minimize as much as possible variations in experimental conditions. For example, after the equipment had been assembled, the billet was allowed to heat up to temperature inside the insulated container. Once the container attained the desired temperature, a period of 1/2 hr was allowed to elapse before the extrusion was made. This time was found to be required to allow the billet to reach a steady-state temperature, as determined from previous tests. When all was ready, extrusion was carried out without interruption; that is, the billet was upset and extruded in one operation. EXPERIMENTAL RESULTS AND DISCUSSION The two usual experimental approaches for investigating high-temperature deformation exhibit an important common feature. In the first approach, which corresponds to creep, a constant stress (or load) is applied to the material at constant temperature and the resultant strain is recorded against time. After an initial transient stage, a state of constant strain rate exists (secondary creep), in which a steady-state condition is established which is sensitive to variation in either applied stress or temperature. In the second approach, a constant strain rate is applied and the resultant flow stress is recorded. This corresponds to the situation in hot torsion or hot compression, where it is observed that, for a constant test temperature, there is an initial rise in stress to a steady value which is maintained up to very high strains. In tests of this type, a steady-state region is also established in which the stress is sensitive to variation in either the strain rate or the temperature.3,4,6-16 In both types of tests, therefore, a steady-state region is established after an initial transient. In the case of hot-working this region may be called steady-state hot-working, and it is analogous to steady-state creep with which it has many common features. Stress Dependence of the strain Rate in Extrusion. In order to assess the stress dependence of the strain rate under extrusion conditions, and to compare it to that of creep, as well as of hot torsion and hot compression, the extrusion data were analyzed according to power, exponential and hyperbolic sine creep equations.

Jan 1, 1969

By James E. Lawver, Jose M. Pastrana

Some of toe magnetic properties of minnesotaite (general formula: Fe3(OH)2Si4O10) were examined. Toe paramagnetic susceptibility values at various temperatures were determined from toe slope of toe magnetizing curve. These values were then compared with toe theoretical values estimated using toe Bohr magneton numbers for toe paramagnetic ions contained in toe missesotaite.

Jan 1, 1975

By J. J. Kanter

The choice of a nonferrous metal or alloy for a given Application is frequently predicated upon a consideration of properties other than merely the capacity to withstand stress. When ability to withstand stress is the dominant engineering requisite of the material to be used, economic considerations seldom lead to the choice of nonferrous metals and alloys. In most instances where a nonferrous metal is used it is because of some special quality of either corrosion resistance, electrical properties, thermal properties, antifriction, or fabrication advantage that commends its application. The mechanical properties, as a rule, present an incidental engineering consideration entirely secondary to the special quality deciding its use. Indeed, great ingenuity has often been exhibited by engineers and metallurgists in overcoming the mechanical shortcomings of a nonferrous base material. in order to take advantage of some outstanding property. . With this thought in mind, we might better appreciate some of the problems in stress design. encountered with nonferrous metals and alloys pertinent to a symposium on their creep characteristics. Our considerations must necessarily be far from complete because of the broad range of materials in the nonferrous category for which creep properties assume a technical interest. Creep deformation of these metals can be subject for study at temperatures ranging from ambient to incandescent, depending upon which one is under consideration. Whereas the steel metallurgist thinks of creep as an essentially high-temperature engineering consideration, the same is not necessarily true in the field at hand. The diversity of the creep problems in the nonferrous field is perhaps accountable to some extent for its virginity as a symposium subject. Each research has necessarily been sponsored by some organization or group interested either in promoting the use of a certain nonferrous base or in obtaining data toward the solution of a mechanical difficulty encountered in applying a material indispensable for its special attributes. Perhaps as many techniques of creep testing have been used as there are base metals implied under "nonferrous." Some of the creep problems that have occasioned researches are associated with steam-pressure vessels such as tubes, drums, castings, and forgings of copper-base and nickel-base alloys, cable sheathings of lead and lead-base alloys, electrical transmission lines of copper and aluminum, engine parts die-cast from alloys based on zinc, aluminum, copper— soldered and brazed joints-—as well as numerous duties at extremely high temperatures met with alloys based on cobalt, nickel, tungsten, molybdenum, platinum, and other precious or semiprecious metals. Postwar technology will have the benefit of much creep research on nonferrous metals, which for reasons of security cannot be discussed on this occasion. Suitability OF Metals As already intimated, the bulk of the constructional metal that ordinarily is

Jan 1, 1945

By Carl J. McHargue

Rods of 99.99 + pct Al which had initial orientatzons of <001>, <118>, <115>, <111>, and random were swaged at room temperature. Changes in orientation as a function of deformation were studied on axis distribution charts. The <001> orientation appeared to be relatively stable due to the inhomogeneity of the deformation process. near the <100> zone were quickly reoriented towards <001>. Orientations on the <110> zone between <118> and <115> appeared to be stable to reductions of about 50 pct, then were reoriented toward <001>. At very high reductzotzs. movement away from the <111> orientation was observed. the requirement that a circular cross section be maintained. In addition to these mechanical factors, there are grain-boundary effects in poly crystalline materials which are not yet understood. Hartmann and Macherauch conclude, for example, that multiple slip occurs for all orientations in fine-grained aluminum and copper and that the choice of operative slip systems has no simple relationship to orientation.? Many investigators have attempted to avoid problems of interpretation caused by an initial texture by treating the starting material to obtain as ran- IT has been generally accepted that the deformation texture obtained at high reductions, e.g. 90 pct, will not be noticeably affected by a prior texture; whereas, that obtained at reductions of 40 to 50 pct may be significantly influenced by the specimen history.&apos; Some recent studies, however, have been interpreted as showing that an initial texture strongly influenced the deformation textures in rods at reductions greater than 90 pct. Freda and Cullity suggested that the <001> texture in a heavily cold-worked copper rod was due to a <001> texture in the original casting. McHargue, Jetter? and Ogle concluded that the <001> component in an aluminum rod extruded at liquid nitrogen temperature was remanent from a <001> texture in the cast extrusion billet.3 Most of the published work on the effect of initial orientation on deformation textures has been for cold-rolled or compressed single crystals,4-6 The primary interest in these studies was to examine various orientations with regard to their stability under flow? thus determining the possibility of such orientations being stable end orientations. There appears to be no published studies on the effect of initial orientation on fiber textures in polycrystalline specimens. A recent study, however, is concerned with the reorientation of individual grains in polycrystalline specimens pulled in tension.? Although the reorientation of single crystals loaded in simple tension is well known, the movements in the forming of wires and rods would be expected to be different due to the circular array of radial-compressive stresses exerted by the die walls or the rolls, and to

Jan 1, 1962

By Frank W. Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength, consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig. 1 was drawn.

Jan 1, 1928

By T. A. Read, H. K. Birnbaum

Deformation of AuCd alloys having the 8 (orthorhombic) and (3" (tetragonal) structures occurs by the stress induced motion of twin boutdaries. A restoring force acts on displaced twin boutdaries as a result of internal energy increases in the volume through which the boundaries are displaced. The phenomonology of the twin boundary motion is described and a mechanism for twin boundary motion and the restoring force is proposed. A time-dependent stabilization behavior of the twin boundaries, which is observed after the twins are formed by the diffusionless phase transformations, is described. THE AuCd 8 phase (ordered bcc structure) exhibits a transformation to a phase having an orthorhombic structure, 8&apos; (space group D&apos;), for compositions in the vicinity of 47.5 at. pct Cd and to a phase having a tetragonal structure, 8" (point group 4/m, m,m), for compositions in the vicinity 50.0 at. pct Cd. Both transformations are diffusionless, occur on cooling at 60" and 30OC, respectively, and are crystallo-graphically reversible.&apos; They are accompanied by an inhomogeneous deformation which was observed to be twinning in the low-temperature phase. 3&apos;4 The transformations may occur by a "single interface" or by "multiple interfaces."5&apos;6 In the "single interface" transformation, the twinned product phase consisted of two twin orientations as shown in Fig. 1. In the multiple interface transformation the product phase contained "domains" each of which contained two twin orientations, Fig. 2. Deformation of specimens containing transformation twins was achieved by motion of the twin boundaries. Releasing the applied stress resulted in the displaced twin boundaries returning towards their initial positions. This "pseudo-elastic" behavior of the boundaries varied with time after the formation of the twin boundaries by the transformation.

Jan 1, 1961

By J. D. Hanawalt, W. H. Gross

Magnesium has long been known as the lightest of our engineering metals. This metal, silvery white in color, has a specific gravity of only 1.74. Aluminum, the next lightest structural metal, is 1 ½ times heavier; zinc is 4 times heavier; iron and steel are 4 ½ times heavier; and copper and nickel are 5 times heavier. Magnesium does not occur in the free state but is very abundant in nature, constituting 2.5 pct of the earth&apos;s crust in the form of various ores. It is the third most abundant structural metal, being exceeded only by iron and aluminum. Magnesium is unique, however, in that in the form of magnesium chloride it also exists in the oceans. Sea water is the source most widely used for production in the United States but magnesium is also commercially produced from magnesite, dolomite, and other ores as well as from certain inland brines. The vast quantity of magnesium existing in the waters of the oceans can be visualized when it is realized that the removal of one hundred million tons per year (the approximate annual steel production in the United States) for a million years would reduce the magnesium content of sea water only from 0.13 to 0.12 pct, providing no more magnesium had washed into the sea in the meantime. Not only is magnesium potentially very abundant but it is in addition a very versatile metal and can be shaped and worked by practically all methods known to the art of metal working. It can be cast by sand, die, and the various permanent-mold methods;

Jan 1, 1953

By C. F. Tolman

In February 1913, Prof. L. C. Graton and Dr. Joseph Murdochl presented to the American Institute of Mining Engineers a notable contribution to economic geology under the title The Sulphide Ores of Copper. The value of the work was recognized by mine operators, and Mr. Graton was assisted in his plan to extend his investigations, by the organization of a commission to undertake a "secondary enrichment investigation." In this work he secured the cooperation of the Geophysical Laboratory of the Carnegie Institution of Washington. The report2 on the chemical phascs of the investigation has just been published. Incidental to investigations3 carried on in our laboratory of Economic

Jan 1, 1916

By J. C. Shyne, T. D. Gulden

The steady-state creep behavior, in compression, of indium containing a dispersion of atomized glass particles was studzed over a range of temperature, stress, and composition. The observed behavior was not consistent with a simple model of dislocation climb over dispersed particles. From room temperature to about 100°C the temperature dependence could be described by an activation energy about one and a half times that of self-dijfusion in indium while at higher temperatures a much higher ternperature dependence was observed. THE value of dispersion-hardened and precipitation-hardened alloys has long been recognized. The mechanism of hardening, however, is not completely understood, especially at elevated temperatures where dispersed particles increase creep resistance. Following the suggestion of Schoeck1 that the rate of creep in dispersion-hardened materials is controlled by dislocation climb over second-phase particles, Ansel and weertman2 derived steady-state creep equations for dispersion-hardened materials. Their derivation was based on dislocation climb over non-deformable spherical particles in a metallic matrix. For low stresses they predicted a linear relation between applied stress and steady-state creep rate. For stresses large enough to cause dislocations to pinch off around the precipitate particles, the theoretical creep rate was shown to be proportional to the fourth power of stress. For very high stresses an exponential stress dependence was predicted. In all cases the theoretical creep rate is linearly proportional to the diffusion coefficient. This provided the primary temperature-dependent factor. Subsequently, Ansel and Lenel3 reported some experimental data on SAP, a composite of aluminum and aluminum oxide, that was in good qualitative agreement with the above theories. Their experimental creep rates, however, were four orders of magnitude less than the theory predicts. This was attributed to a low density of active dislocation sources in the material; somehow the dispersed particles inactivated the dislocation sources instead of merely interferring with dislocation motion. Meyers and sherby4 have recently reported on the creep behavior of SAP. Their results were inconsistent with a simple dispersion-strengthening model and led them to conclude that a continuous network of oxide controls the high-temperature mechanical characteristics of SAP. Because of the rather complex mechanical behavior of SAP and the lack of agreement about the morphology of its oxide phase, it appeared desirable to study the creep of a dispersion-strengthened material of controlled morphology. For the present work a dispersion of spherical glass particles imbedded in a matrix of indium was chosen. The microstructure of this material was similar to the idealized uniform dispersion of hard spheres in a deforming matrix assumed by Ansel and Weertman in their theoretical treatment. SPECIMEN PREPARATION For experimental convenience, it was decided to use a low melting-point metal in this investigation. It was necessary that the metal not be oxidized readily up to its melting temperature and that it wet the second-phase particles. It was desired that the material chosen for the dispersed phase be available as a fine powder with closely controlled size and shape. The material chosen to satisfy these requirements consisted of a matrix of indium metal containing a dispersion of atomized particles of a soft soda-lime-silica glass ranging from 5 to 30 µ in diam. The glass particles had a highly regular spherical shape. The composite was made by stirring the glass powder into liquid indium maintained at a temperature just above the melting point of indium, 156°C. The creep specimens were prepared by a hot pressing operation. Five to ten g of the mixture were placed in a steel die and pressed at 125°C for 5 min under a pressure of 30,000 psi. The resulting specimens were cylinders about 3/8 in. in diam and ranged from 0.4 to 0.7 in. high. By following this procedure a uniform dispersion was obtained in the creep specimens. Typical microstructures of specimens containing twenty and forty volume percent glass powder are shown in Figs. 1 and 2. Unfortunately, grain size could not be determined by the metallo-graphic techniques used. CREEP TESTING PROCEDURE Creep tests were performed in compression under constant stress. The specimens were placed in

Jan 1, 1963

By W. R. Ingalls

In reviewing the history of the metallurgy of zinc, I shall pass hastily over what is only of antiquarian interest. That has been excellently treated by Dr. Bernhard Neumann in "Die Metalle" (1904) and has been described briefly in my "Production and Properties of Zinc" (1902), in my "Lead and Zinc in the United States " (1908), and in other metallurgical works of more or less the same date. In this present monograph, I have it in mind to confine myself mainly to technical practice, especially to that of the last 75 years, prior to which period advance was slow and of no great moment. The ancients made brass by the cementation process, i.e., embedding copper in a mixture of calamine and carbon and heating, whereby zinc oxide was reduced and zinc was vaporized and combined with the copper. Zinc was isolated by some of the alchemists, who named it and knew something of its properties, but made no use of it. Long before then, however, zinc was produced in India. Later it was produced in southern China. Possibly the Chinese obtained their knowledge from India. The Chinese in remote places still produce small quantities of zinc. I have seen photographs of their furnaces; or pots, for they hardly deserve the dignity of being called furnaces. I imagine that they are the same that were used centuries ago, for I cannot conceive of anything more primitive. Anyway, it is certain that the idea of a commercial production of zinc in Europe was imported from the Orient, where the metal was known in commerce as Speauter and Spiauter, whence speltrum and finally our term spelter. Tutanego and Tuteneague are other old names. Dr. Isaac Lawson went to China about 1730, expressly to discover the method of its production. What connection there was between Isaac Lawson and John Champion we do not know, but the latter obtained in 1739 a patent for a process of distillation downward and at some time between 1740 and 1743 erected a works at Bristol and actually began the manufacture of spelter. A production of 200 tons per annum is mentioned. In about the year 1766, Rishop Watson visited the Champion works and saw the process in operation, which previously had been

Jan 1, 1937

By Frank Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper, wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength; consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig.1 was drawn.

Jan 1, 1928

By Fritz Wald, Martin Weinstein, Herbert E. Bates

ONE of the methods for preparing a fiber-reinforced composite is that of directional solidification of a eutectic melt. Its major drawback lies in the fact that the matrix in this case is a pure constituent (or a terminal solid solution of fixed concentration) and the ratio of fiber to matrix volume is fixed. Only very few, if any, pure metal matrices possess technically useful properties, and the necessity for alloying is the inevitable consequence of this fact. Nevertheless, structures similar to binary eutectic ones can be obtained in higher-order systems by pseudoeutectic reactions of a type where crystallites and a solid-solution matrix are simultaneously precipitated from a liquid.1"3 Trials to solidify such alloys directionally—the matrix consisting of a solid solution of chromium, nickel, and silicon and the reinforcing phase being Cr3C2— will be reported elsewhere.4 This note describes constitutional studies carried out primarily to determine -the position of the pseudoeutectic and further to insure that no undesirable reactions between the reinforcing phase and components of the matrix occur in the solid state at elevated temperatures. In the investigation it was specifically desired to reinforce a matrix which is as close as possible to the 80/20 Nichrome composition with Cr3C2 to insure good oxidation resistance and improve the strength at high temperatures. No konstitutional information on the quaternary C-Cr-Ni-Si svstem in the range of interest was found in the literature. Nevertheless, the two most important ternaries c-cr-Ni5 and have been completely investigated. On C-Cr-Si some investigations have been conducted,7"9 and C-Ni-Si was studied with a few alloys in the course of the present investination 9 Eight alloys were prepared to investigate the changes in the constitution of the ternary C-Cr3Ce-yNi eutectic5 with silicon contents up to 10 wt pct. Five alloys were made with varying chromium and carbon contents around compositions containing -60 to 70 wt pct Ni and 5 to 6 wt pct Si. The latter alloys were designed to locate the y(Ni-Cr-Si-C)-Cr3C2 pseudoeutectic reaction and to determine the maximum chromium content in solid solution compatible with a two-phase equilibrium between y and Cr3C2 only. The alloys were prepared from electrolyte nickel, semiconductor-grade silicon, high-purity chromium (99.999 pct pellets), and semiconductor-grade graphite. They were melted inductively in high-purity alumina crucibles under flowing argon. Twenty-gram charges were prepared and investigated by optical microscopy (including hot-stage investigations), X-ray powder methods, and electronmicroprobe analysis. The alloys were studied in the as-cast condition and also after a homogenization annealing treatment of 48 days at 900°C in evacuated quartz ampoules. The structures of all alloys based on the ternary eutectic plus silicon in the as-cast state consisted generally of an inhomogeneous solid solution and at least two other phases. Annealing of the alloys showed that the solid solution was homogenized but that an incomplete solid-state reaction had taken place in all alloys with silicon contents over 5 wt pct. This reaction is clearly visible in Fig. 1 around the large Cr3C2 crystals (gray areas). Below this concentration, the alloys consisted of a homogeneous matrix and precipitates of Cr3C2 plus graphite, Fig. 2. The Cr3C2 was entirely unreacted here. From these observations and subsequent X-ray and microprobe investigations, it was deduced that the

Jan 1, 1969