Search Documents

By R. I. C. Manning

The Old Dominion Co, at Globe, Ariz., like the: Phelps Dodge Corporation with which it is closely allied, considers safety a major operating problem. Safety is fostered by this company in consideration of both the humanitarian and economic aspects; the officials, take pride in promoting the welfare of employees, and the management has found that the safest way is the most eco¬nomical and that unless an organization is operated economically it can not continue to exist successfully. In planning and operating any safety, organization, terry things must be taken into consideration because an Enterprise can not be operated solely for safety any more than it can for any other single part of the operations. All work must be planned and executed for the common interest.

Jan 1, 1931

By J. W. Hunter, J. H. Jacobs

"Approximately 355 tons of nodules from Chamberlain; S. D., ore were processed in the 1-ton-per-day electrolytic-manganese pilot plant of the Bureau of lanes at Boulder City, Nev., in a continuous 3-month operation. The ore, ground to minus 48-mesh, was found to be amenable to leaching with acid directly or after roasting under reducing conditions in a Skinner muffled multiple-hearth furnace.Unroasted ore gave an acid-leach extraction of 84 to 88 percent of the manganese, which after neutralization showed an over-all extraction of between 81 and 85 percent of the manganese. The amount of iron extracted varied, but it was always,enough to permit the use of ammonia for neutralization.Roasted ore showed an acid-leach extraction of 89 to 91 percent of the manganese. A large amount of iron went-into solution, so that it was not economical to neutralize it entirely with ammonia. By neutralizing with calcine to a pH of 5.0 and completing -neutralization with ammonia to a pH of a.5 an over-all manganese extraction of 84 to 86 percent was obtained. The slight increase in. extraction on roasted ore probably would not justify the cost of roasting.Acid consumption averaged 1.75 pounds per pound of manganese extracted. Settling rates of the residue in leach solution were to slow to permit clarification in thickeners, but a Moore vacuum leaf filter proved to be satisfactory. Purification of raw leach solution was .accomplished readily by hydrogen sulfide with a low gas consumption. Electrolysis was normal, without difficulty, and with -current efficiency ranging between 62 and 66 percent.The use of Chamberlain modules for the production of electrolytic manganese would result in an operating cost of 0.8316 cent per pound higher than the cost of producing electrolytic manganese from Three Wids ore."

Mar 1, 1946

By Jochen Wans

BCT® - Belt Casting Technology is the new horizontal near-net-shape casting process to produce flat steel products. BCT is the revolutionary leap in casting technology, designed for the production of special and conventional steel grades. Within a partnership between Salzgitter Flachstahl GmbH and SMS Siemag AG, the worldwide first caster is now in operation. SMS Siemag AG (in cooperation with Salzgitter Flachstahl GmbH) has erected the first industrial-scale casting machine located at Peine steelworks. The lecture will start with an overview about the highlights of the BCT® process with regard to the mechanical engineering aspects, while the second part will present current commissioning results and operation experiences. Since December 2012, the BCT plant is running. Up to March 2015 more than 90 casts have been carried out, 26 with FeMn-alloys. Never before flat steel was casted in dimensions of 1000 mm * 15 mm and with casting speeds more than 14 m/min.

Aug 16, 2017

By D. Potter

In 1990, Freeport Exploration began regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the republic of Indonesia (Fig. 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work that totaled 2.6 million hm2 (6.4 million acres). The company was subsequently awarded additional concessions that added 1 million hm2 (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments, Freeport’s current land position totals 1.9 million hm2 (4.7 million acres). Freeport began the exploration program to locate additional Grasberg deposits, the largest deposit in the Ertsberg district. But the company recognized that other types of deposits could be present in the largely unexplored area of Irian Jaya.

Jan 1, 1999

By Shuie Li, Taibai Li, Tao Hu, Zhongjie Wang, Xiang Ge

As one of the main power sources, lithium-ion batteries (LIBs) will continue to be applied on a large scale in the future market. Commercialized LIBs cathode materials contain various valuable metal elements including Li, Co, and Ni. The development of green and efficient recycling technology is essential. Deep eutectic solvents (DESs) have recently emerged as a new class of green solvents that could potentially be applied for the LIBs recycling industry due to their capability to leach the active materials without the introduction of environmentally hazardous reagents as used in conventional hydrometallurgy process. Considering the rapid progress, a critical review focusing on the progress and fundamentals about the overall efficiency has practical significance for the further advancement of this field. Herein, we briefly introduce the overall process of using DESs for LIBs recycling and specifically focus on the efficiency of each step. Current fundamental understandings and new experimental approaches to enhance the efficiency of the leaching process, the extraction process, and reusability are summarized. We expect this review article to inspire scientists to use DESs as powerful tools for advancing the frontiers of LIBs recycling.

Jul 30, 2022

By Serge Rudchenko

A study to determine the potential use of retaining structures in open pit backfilling. Research and review of the open pit mine environment, mine waste disposal, and past and current use of retaining structures. A development of specific structures, the culvert/ tunnel concept, and an anchor block retaining concept. The cost benefit of retaining structures used for in-pit backfilled waste.

Jan 1, 1981

By Arun .. J. Basu

The paper introduces Intelligent Air Management (IAM) as the core activity of M&I Group of Companies (M&I) for providing a total solution to any air management problems for mining and mineral processing operations implementing a comprehensive systems approach through a world-wide network of strategic alliance partners and in-house engineering team and manufacturing facilities in Mississauga, Ontario, Canada. Recommendations for energy-efficient ventilation in a vibration and noise free environment are made with the patented and innovative solutions supported by extensive computational fluid dynamics (CFD) studies. The solution scope extends from an intelligent and integrated exhaust silencer to a complete ventilation sys-tem solution including inlet and outlet control design and ducting for diffusers and silencers.

Apr 1, 2005

By Robert L. Lappi

Volume I of this report described the demonstration of cross-ridge mountaintop coal mining. This document, Volume II, is intended for use as a supporting document to Volume I. This report describes the MATHMINE Mine Simulation System, a modularized software system used to support the demonstration of cross-ridge Mountaintop coal mining. The MATHMINE Mine Simulation System was used to generate mine plans for coal extraction at lowest cost. The functional details, data requirements and output of the software system are detailed here. The computer program was written in FORTRAN. One module which generates resource location data required the use of SAS?.

Jan 1, 1984

By T. L. Joseph

The Bureau of Mines gas been studying the blast furnace for a number of years and has published detailed reports on various phases of its investigations. Inquiries frequently received for information of a more general character than that given in the detailed reports have promoted the preparation of an information circular to cover in a general way the important features of the Bureau of Mines blast-furnace investigations. SHAPE AND DIMENSIONS OF FURNACE The modern blast furnace approximate a refractory-lined steel cylinder about 90 feet in height and 25 feet in diameter. It actually consists of a number of cylinders and truncated cones superimposed upon each other. The shape and dimensions of a modern furnace are shown in figure 1. The bottom section, commonly referred to as the hearth or crucible, is a cylindrical section about 12 feet high. Liquid metal and slag collect in this part of the furnace and are withdrawn at regular intervals; iron is removed at a level about 2 feet above the bottom of the furnace and slag at a level about 5 feet higher. Depending upon on the size of tie furnace, 40,000 to 75,000 cubic feet of preheated air per minute is introduced through from 10 to 16 tuyeres equally spaced around the periphery of the hearth.

Jan 1, 1934

By L. F. Willmott

The Bureau of Nines at Morgantown, W. Va., has been investigating, on a pilot plant scale, various methods of gasifying bituminous coal with oxygen and superheated steam to produce synthesis gas, as part of the broader program of finding new uses for coal. Differences in the pressure gasification methods used have depended on differences in the manner in which the pulverized coal is fed to the gasifier. One of the methods of feeding the coal that was investigated was the continuous, integrated coal-water slurry system. Goal and water were first mixed to produce a slurry; then the slurry was pumped through a heated coil. to evaporate the water fraction; the resulting steam was superheated, and some of it was separated so as to adjust the ratio of the residual steam to the coal fraction and make the resulting mixture suitable for partial combustion with oxygen in a pressure gasifier. Both before and during this reported3 developmental work it was necessary to make an extensive literature search into the technology of aqueous slurries in order to establish design criteria for the pilot plant and to correlate results of various phases of the work with that of other investigators, The pilot work coincided with the commercial development of a long-distance pipe- line for the transportation of coal as a coal-water slurry, and this fact tended to broaden the scope of the pilot plant work and the extent of the literature search. This bibliography is the compilation of the material that was collected.

Jan 1, 1963

By G. Swan, E. Nordlund, P. Zhang

"SynopsisThe most widely used support design damage criterion for rockburst-prone mines is based upon kinetic energy, which is proportional to the square of the ejection velocity and is commonly expressed in terms of peak particle velocity (PPV). Field monitoring and back-analyses have shown that ejection velocities of the order of 10 m/s and higher can result from seismic events of moderate magnitude. Such velocities are much higher than those predicted using PPV obtained from scaling laws. It has also been found that the peak ground motion (i.e. PPV) on the surface of an excavation is preferentially amplified (by four- to tenfold) compared to the motion in solid rock at a similar distance from the source. However, the wave propagation and interaction processes involved within the fractured rock in generating high ground motion are very complex and are not well understood at this time.In this paper, velocity amplification was investigated by modelling the dynamic interaction between fractured rock and a free surface using a 2D discontinuum-based numerical program, UDEC (Universal Distinct Element Code). A 1D model with a fractured zone was used to represent the fractured rock. Velocity amplification, quantified by PPV, predicted at the free end of the model was 2.0–3.6 times higher than the input velocity. It was found that the wave frequency, fracture stiffness, fracture spacing, and thickness of fractured zone are the main factors that affect the velocity amplification. The results have proved that the interaction of the seismic wave and multiple fractures near the free surface strongly influences the ground motion.IntroductionSince mining-induced seismicity is almost inevitable in deep mines, ground support is generally employed to mitigate the risk of seismically-induced damage. The most widely used support design criterion for seismicallyprone mines is one that seeks to maximize the absorption of the kinetic energy (plus potential energy if a gravity component is considered) of key rock blocks. Based on this criterion, design methods for rock support were first proposed by Wagner (1984) in South Africa and later improved, among others, by Roberts and Brummer (1988) and Kaiser et al. (1996)."

Jan 1, 2015

By Dimitrios Litsas, Michael Kavvadas, Panagiotis Sitarenios

"The paper discusses the results of 3D finite element analyses to investigate the effect of face support pressure and soil permeability on face stability conditions in EPB tunnelling. Two main types of face behavior are identified: Undrained conditions ahead of the tunnel face, typically occurring in soils with permeability less than about k=5·10-7m/s, are shown to be favourable for face stability; analyses show that an applied face pressure comparable with the initial hydrostatic pore pressure is sufficient for adequate face stability, even for soils of relatively low strength. Drained or partially conditions, typically occurring in soils with permeability higher than about k=5·10-6m/s, show that face stability is strongly dependent on the horizontal effective stress of the muck in the excavation chamber; the presence of even a small effective stress in the muck is very beneficial for face stability conditions and can be a possible explanation of successful EPB tunnelling through relatively permeable soils. INTRODUCTION Face stability is probably the most important aspect in urban tunnelling. Usually, Earth Pressure Balance (EPB) machines are utilized, to ensure that a reasonable amount of face pressure is exerted on the advancing excavation face, reducing ground loss and preventing potential instability of the face core, thus controlling the amount of disturbance caused by tunnel excavation to surface structures. However, the ideal amount of face pressure depends on several factors (ground and groundwater conditions, tunnel size and depth, muck conditioning, etc.) which are difficult to include in analytical calculations. For many years, conventional empirical or analytical methods (e.g. Anagnostou & Kovari 1996) were the only available tools for quantifying face stability and selecting the required face pressure. In the last few years, however, numerical analyses have gained power over conventional methods, allowing more accurate designs and providing useful information about the anticipated ground deformations due to tunnelling. Numerical analyses have also been used in assessing safety against face instability using face extrusion (horizontal face displacement) calculations (e.g. Prountzopoulos 2012)."

Jan 1, 2016

Jan 1, 1992

By Bern Klein, Randy Blaskovich, Reem Roufail

"Morphology is a tool that is rarely used for mineral breakage mechanism evaluation. Ground particles are typically assessed for their size distribution. They are also visually analyzed using image analysis. However, image analysis is not a comprehensive evaluation of the particle surface texture. It evaluates particle’s size parameters such as area, diameter, and perimeter amongst other features. On the other hand, morphology analysis takes the particle assessment to another level of detail. Morphology analysis evaluates particles’ roundness, elongation and angularity that would indicate the degree of roughness of the particle. According to Roufail and Klein (2009), rougher surfaces are generated due to breakage along grain boundaries – intergranular breakage. Mill operation, particularly mill speed, dictates the dynamics in the mill. Stirred mills are known to break the particles via abrasion under standard operation. However, if the dynamics of the grinding media in the mill are changed, the particles could be more exposed to impact and compression loading that would lead to a different mode of breakage.In this paper, the effect of material properties and mill operating conditions on particle morphology will be studied. Hard non-sulfide versus soft sulfide minerals are compared, namely quartz and galena, respectively. Extreme mill speeds are tested covering the range of 1000 to 2000 rpm for a 4-litre Netzsch (ISA) mill. In addition to particle size distribution, micro-analysis is executed in the form of morphological analysis using a tested manual roughness point counting technique.INTRODUCTIONGrinding in general and stirred milling in particular are processes that are used to break particles to liberate metal-bearing minerals for further separation downstream. The energy required to achieve the target particle size versus maximum possible liberation has been studied intensively and it is usually the breaking point for the grinding system chosen in a process flowsheet. Operating conditions are dictated by the energy consumption. Becker et al. (2001) related different forms of energy such as input, specific, volume/mass specific energies to stress intensities and final product fineness. Other research studies focused on energy input in a stirred mill (Zheng, Harris and Somasundaran, 1996)."

Jan 1, 2011

By T. Hadley, E. Catovic

"Northern Minerals Limited’s (ASX: NTU) flagship project is the Browns Range Rare Earth Project (the Project) located in Western Australia, consisting of a number of deposits with high value, heavy rare earth elements, in particular yttrium, terbium, and dysprosium. The deposits are dominated by xenotime mineralisation, which occurs within hydrothermal silicified and hematitic breccias. The Company delivered an initial JORC compliant resource estimate for the Project at the end of 2012 of 10,500 t of contained total rare earth oxides (TREO), which was increased to 28,084t of contained TREO in October 2013 and further enlarged to 47,997 t of contained TREO in February 2014. Concurrent with the growth of the Project resource base, significant progress has been made in developing the metallurgical process for the beneficiation and extraction of rare earth elements (REE’s) from the xenotime mineralisation. Development of the beneficiation circuit evaluated several process options and selected whole-ore flotation and magnetic separation, followed by flotation (hybrid circuit) as the two preferred flowsheets to pilot, following encouraging results on the bench of 83% and 86% recovery to a 20% TREO mineral concentrate respectively. Several downstream hydrometallurgical extraction flowsheets were evaluated. However, the following two preferred process flowsheets were ultimately selected for further detailed investigation during the prefeasibility study: 1. Sulphation bake, water leach, purification, oxalate precipitation, and/or calcination to produce a mixed RE oxide; 2. Sulphation bake, water leach, phosphate precipitation, caustic conversion, HCl leach, and oxalate precipitation to produce a mixed RE oxalate. Excellent heavy rare earth oxide (HREO) extractions (~ 90%) from beneficiation concentrates were achieved on the bench for both circuits, however flowsheet 1 was ultimately selected as the preferred flowsheet to pilot due to lower capital and operating cost. A mixed rare earth oxalate (42% TREO) or oxide (92% TREO) can be produced with low levels of Th and U of 3 ppm and 6 ppm respectively."

Jan 1, 2014

By T. F. Mitchell, B. K. Shibler, J. V. Batty, W. G. Sandell, G. M. Potter

"INTRODUCTION The Park City district, situated 30 miles east of Salt Lake City, Utah, in the Wasatch Mountains, Is a well-known producer of lead, zinc, and precious metals. Nearly continuous production has been maintained from the dis¬trict since its early discovery about 1870. For approximately 50 years, gravity milling methods were employed to beneficiate Park City ore, and during that time tailings from the mills were sluiced down Silver Creek and deposited on lands below the camp for 7 miles.Owing to the large tonnage of tailings deposited along Silver Creek, considerable work was done in the past in the attempt to develop a low-cost concentration method for re-treating this material, but no-method was found that was economically feasible. The Bureau of Mines was asked to conduct beneficiation tests on Park City tailings in November 1944, and metallurgical studies were initiated at that time. This report summarizes the results of laboratory ore-dressing studies made on samples from the Grasselli deposit."

Dec 1, 1947

By Briggs H.

The illustrated device uses the principle that the lamp can burn with a smaller inlet passage if the air is rich in O2 and that the size of the inlet can be made a measure of O2 percentage. The appliance consists of an adjustable cut-off applied to the inlet of a safety lamp of the improved Gray pattern. Precision is assessed from tables of calibration tests in air contaminated with blackdamp of CO2:N2 composiiton 1:5.67 at temperatures of 40-70 degrees F. Results are presented of tests at St. Germain's colliery, of tests in air contaminated with pure CO2 and of air contaminated with both blackdamp and inflammable gas; published ranges in mine-air blackdamp compositions are tabulated as ranging from 90.06% N2 to 43.90% CO2. When firedamp is present at 1.25-2.5%, its content must first be estimated by means of the cap and a fifth of its value then deducted from the lamp reading for O2

Dec 1, 1916

By A. J. Monhemius

"This paper reviews the history of modern iron-control processes in hydrometallurgy. Attention is paid to processes developed in the electrolytic zinc industry for removal of iron from zinc sulfate leach liquors and the problems faced by the industry in the safe disposal of the iron residues produced by these processes. Past lessons learned are projected onto current efforts to develop hydrometallurgical processes for treatment of copper sulfide concentrates. It is argued that any attempt to create a “hydrometallurgical copper smelter” will fail, unless methods are developed that can recover iron in a form that can be directly used by the steel or pigment industries.RÉSUMÉ Cet article passe en revue l’histoire des procédés modernes de contrôle du fer en hydrométallurgie. Il accordera une attention particulière aux procédés développés dans l’industrie du zinc électrolytique pour l’élimination du fer dans les liqueurs lixiviantes de sulfate de zinc anhydre, ainsi qu’aux problèmes rencontrés par l’industrie en termes d’élimination sans danger des résidus ferreux générés par ces procédés. En projetant les leçons tirées du passé sur les efforts actuels, on pourra développer des procédés hydrométallurgiques pour le traitement de concentrés de sulfure de cuivre. Beaucoup prétendent que toute tentative de créer une « fonderie de cuivre hydrométallurgique » échouera à moins de développer des méthodes permettant de récupérer le fer sous une forme pouvant directement être utilisée par les industries sidérurgique ou des pigmentsINTRODUCTIONThis paper resulted from an invitation to the author from the CIM’s Historical Metallurgy Committee to give a presentation on the early developments of iron control in hydrometallurgy. This was to take the form of a plenary lecture at the 4th Symposium on Iron Control in Hydrometallurgy, which formed part of the 28th International Mineral Processing Congress, held in Quebec City in September 2016.I was naturally flattered that the invitation was to give the lecture at an IMPC, the prestigious conference series that has been held since the 1950s. That this particular IMPC was to include the 4th Symposium on Iron Control in Hydrometallurgy, a conference series held only every 10 years, made the invitation even more appealing and appropriate. This was because I had been co-chairman of the First Symposium on Iron Control, together with my erstwhile colleague, John Dutrizac, which was held 30 years ago in Toronto."

Jan 1, 2017

By Xuemei Zheng, Aiyuan Ma, Chao Liu, Guojiang Li, Chenyu Sun, Jinhui Peng, Libo Zhang, Yongguang Luo

In this paper, the removal of fluorides and chlorides from blast furnace dusts by water vapor enhanced microwave roasting was investigated, combined with the advantages of microwave selective heating and based on a thermodynamic analysis of zinc and lead halides. According to proposed reactions in the process, detailed experiments were systematically conducted to study the effect of roasting temperature, holding time, air flow, water vapor flow rates, and stirring speed on the efficiency of the removal of F and Cl. The results show that 97.26% of F and 64.23% of Cl could be separated when the condition of the roasting temperature of 650°C, stirring speed of 80 rpm, holding time at 60 min, air flow of 350 L/h and water vapor flow rate of 8 mL/min was optimized.

Jan 1, 2016

The Annual General Meeting of the Branch was held in the Witbank Golf Club on Thursday, 28th August, 1969 at 5.00 p.m. Mr C. G. Sowry (Chairman) was in the Chair. There were also present: Ten Members: Messrs J. Meintjes (Vice-Chairman), J. E. van Aswegen, A. C. Hofmeyr, I. Botha, B. F. v. d. Merwe, C. H. Coxon, R. Canny, R. C. J. Goode, A. Bain, G. E. Carlyon. Six Associate Members: Messrs B. T. Hosking, R. E. Powell, W. Weber, T. Bulloch, E. J. Jackson, P. J. Muller. Fourteen Visitors. Total Present: 31. The Chairman declared the meeting open and extended a welcome to all visitors including Mr R. C. J. Goode, President of the Institute. MINUTES OF PREVIOUS GENERAL MEETING The Minutes of the General Meeting held on the 26th June, 1969, were read and adopted. CHAIRMAN'S REPORT The Chairman presented a report outlining the activities of the Branch during the past year. Membership of the local Branch had increased from 80 to 99 during the year. DECLARATIONOF OFFICEBEARERS The Chairman announced that owing to his transfer out of the Witbank area, he was unable to accept the nomination as Chairman for a further year of office. The outgoing committee had elected Mr J. Meintjes Chairman and Mr A. Bain Vice-Chairman for the ensuing year. Mr J. Meintjes then took the chair. Mr J. Meintjes thanked Mr C. G. Sowry for his successful steering of the Branch during its period of inauguration. ELECTION OF COMMITTEE MEMBERS The Chairman then read the Scrutineers' Report and declared the following eight members elected as Committee Members for the 1969-1970 year: Messrs I. Botha, A. W. Brereton, G. E. Carlyon, B. T. Hosking, E. J. Jackson, B. D. McNeice, P. J. Muller, B. F. van der Merwe. TALK The Chairman then called upon Mr A. Bain to present his talk and film show on 'Impressions of the mining and metallurgy congress tour to Australasia'. CLOSURE After thanking the speaker for an interesting talk, the Chairman declared the Meeting closed at 8.40 p.m.