Search Documents

By Panshi Xie, Xicai Gao, Yi Luo, Youfu Zeng, Yongping Wu, Shenghu Luo

This research investigates roof deformation and failure characteristics, as well as mechanical interaction between the panels of the roof strata above two adjacent working faces in a steeply inclined coal seam. Physical modeling with photogrammetry measurement method has been employed in this investigation. The movement of roof strata and section pillar, as well as the stratum morphological characteristics, was quantitatively analyzed. Results show that the roof movement direction above the two panels has zoning characteristics, especially in the lower panel. Roof migration in the lower panel of the working face is larger than that in the upper panel. The roof to floor closure perpendicular to the seam direction is larger than the sliding along the seam. The maximum roof concave and convex bending occurred at the middle and upper parts of both panels; the roof bending in the upper panel mining area indicates a larger mining disturbance induced by lower panel mining. The void ratio contour of the lower panel is an asymmetrically arched shape, which is different from that of the upper panel area. The higher roof strata above the upper panel exhibit separation and breaking, whereas the lower roof exhibits compression due to mining in lower panel. The section pillar is compressed and slides slightly, which aggravates the mechanical interaction between the panels and increases the caving height of the roof over the lower panel and the periodic weighting intensity

By W. J. Miles

At the beginning of the 20th century, barite was a mineral of minor importance in the United States. Its primary use was to extend lead oxide in white paint. Barite also added the special qualities of hiding power and flatness to paint. Because white lead sometimes turns black or yellow and barite does not, ground barite became a pigment on its own merit. Barium chloride was added to bricks before fi ring to stop efflorescence when exposed to weather. Barium carbonate or nitrate added luster and brilliance to glass. Barium chemicals were added to refining sugar, enameling iron, making oilcloths and paper collars, and in the manufacture of paper, artificial ivory, rubber and lithopone. Lithopone became a major paint ingredient in the 1920s; its use lasted until the 1950s, peaking at 150 kt (165,000 st) of barite in 1937 and 1947 for the manufacture of lithopone. Later in the 20th century, titanium dioxide replaced lead oxide, barite and zinc oxide in the coatings industry. In the 21st century, barite is used as a filler, extender or weighting agent in products such as paints, plastics and rubber. Some specific uses include its use in brake and clutch pads for automobiles, automobile paint primer for metal protection and gloss, to add weight to rubber mud flaps on trucks and to add weight to the cement jacket around petroleum pipelines under water. In the metals casting industry, barite is part of mold release compounds. Because barite significantly blocks X-ray and gamma ray emissions, it is used as aggregate in high density concrete for radiation shielding around X-ray units in hospitals, nuclear power plants and university nuclear research facilities. Ultra-pure barite consumed as liquid is used as a contrast medium in medical X-ray examinations. Barite is the raw material for barium chemicals, such as barium carbonate, which is an ingredient in faceplate glass in the cathode-ray tubes of televisions and computer monitors. In the 21st century, barite industrial uses accounts for an estimated 78 kt/a (86,000 stpy) in the United States.

Jan 1, 2009

By N. Niemuth

Strong demand for copper in developing nations such as China and India, plus the additional demand for industrial minerals to supply the Arizona construction market, brought about a record-setting year for the state?s mining industry. The value of Arizona?s copper production set a new high of $5.5 billion and pushed the total value of mineral production to $7.58 billion. This was also a record. As it has for many years, Arizona ranked first in nonfuel mineral production in the U.S. In addition to leading the nation in copper, Arizona ranked in the top five in molybdenum, sand and gravel, gemstones, perlite, silver, zeolites and pumice. Generally strong and rising prices, especially toward year?s end, fostered a bullish atmosphere that encouraged significant levels of acquisition and exploration. This activity has spread beyond the normal commodities to include some, such as manganese and fluorspar, that have not been mined in Arizona for decades.

Jan 1, 2008

INTERNATIONAL conferences on safety in mines originated in 1912 when, in response to an invitation issued by the United States, representatives of Austria-Hungary, Belgium, France, and Germany participated in a conference held in Pittsburgh, Pa The record shows that a permanent organization was proposed to be developed through. diplomatic channels. However, the advent of war 2 years later prevented this proposal from coming to fruition. No further cooperation between the Bureau of Mines and a group having: similar interests in a foreign country took place until 1924, when formal cooperation with the Safety in Mines Research Board of Great Britain was established. Interchange of personnel and results of research under that arrangement have resulted in a number of publications in both countries and more rapid advance in knowledge than could have been obtained through the same efforts exerted independently.

Jan 1, 1950

The problem of ventilating an advancing drive which finally reached 5,550 ft from the fresh air base in rock with virgin temperature of 83°F was solved economically by the use of two 15 h.p. electric fans forcing ventilating air through 281/2 in. dia. fiexible polythene tubing of wall thickness 0·010 in. The saving in cost over conventional metal duct was estimated to be £3· 24 per ft of drive.INTRODUCTIONAs described by Dutton (1965) and Newton (1965) the existing 1,480' ft level drive at the South Mine, Broken Hill, was extended in two stages. The first extension was 3,790 ft, the face then being 4,790 ft from the fresh air inlet. Later, after a vertical ventilation connection was made 1,000 ft back from the face, the drive was extended a further 4,550 ft. The rate of face advance in both stages was about 15 ft per day (3 shifts of 5 ft), 5 days per week. Drive size was 8 ft by 9 ft 6 in. high.The Mines Inspection Act of New South Wales requires 6 hr shifts (instead of the normal 7 in Broken Hill) to be worked if the wet bulb temperature exceeds 80°F. Virgin rock temperature on the 1,480 ft level was 83°F. Inlet air temperature varied with seasons from 58 to 72,oF wet bulb.To adequately ventilate the face, a flow of air of about 11,000 c.f.m. was thought to be necessary.Re-entry time was about 75 min, being governed by the 7 hr length of shift (3 shifts per day) and travelling time.Blasting was permitted only at the end of the shift, in accordance with local industrial restrictions.

Jan 1, 1965

By D. J. Parker

In attempting to discuss a subject of this character it should be clearly understood at the outset that the purpose is not to emphasize the mere fact of occurrence of such catastrophes, the memory of which time has largely relegated to oblivion, but rather to stress the means of their prevention, available not only subsequent to but also at the time of occurrence. A careful, conscientious, unbiased study of the causes of mine explosions leads inevitably and definitely to the conclusion that the human element is the most important factor. The human factor should however, be evaluated in terms of responsibility--responsibility on the part of the employer to recognize the existing hazards and take the necessary remedial action, and on the part of the employee to perform his duties faithfully, diligently, scrupulously, and in strict conformity with State mining laws and company rules or other regulations.

Jan 1, 1933

By Kenneth L. Bickel

During an underground mine fire, the importance of controlling the spread of smoke and toxic gases with suitable ventilation structures has been proven. However, under certain conditions, control of the propagation of the fire itself may be even more critical in insuring a safe mine evacuation. Fire doors offer the means for accomplishing both objectives. In 1978, the Bureau of Mines initiated research to evaluate the state of fire-door technology and develop and test a fire door suitable for large openings (10 by 12 ft or larger) in noncoal underground mines. This report discusses current fire-door technology in the context of the underground mine environment and the design, fabrication, lab testing, and in-mine field testing of a mineworthy fire door. This door has a 1.5-h fire resistance rating and limits temperature rise across the door to 2500 F during the first 30 min of fire exposure.

Jan 1, 1987

By Fookes R. A, Gardner K. J, Gravitis V. L, Watt J. S, Steffner E. J

Two radioisotope techniques suitable for the rapid laboratory determination of the ash content of coal have been tested ou unwashed coal samples from four Australian coal seams. In one techniqne, measurements of backscattered 238Pu L X-rays and iron K X-rays from finely ground coal samples have been combined to determine ash content in uuwashed coals to ±0.5 weight per ce111 ash (ls) for three seams and 0.9 weight per cent ash for the fourth.The second technique, which involves measurements of the transmission by the coal of narrow beams of 241Am 60 keV and 123Ba 356 keV ? rays, requires less sample preparat ion. The ash was determined to within the range of 0.8 to 2.6 weight per cent for the four seams (unwashed coal). For washed coals, errors are expected to be < ±0.5 weight per cent ash.

Jan 1, 1982

Overexposure to noise is a widespread, serious health hazard in the mining industry, and causes hearing losses to a large percentage of the mining population. Recognizing this fact, the Bureau has a major on-going research effort to address this problem area. These proceedings include an overview of the Bureau noise control program and summarize nine selected noise control research programs.

Jan 1, 1984

By Janet Torma-Krajewski

Research has shown that an ergonomics process that identifies risk factors, devises solutions to reduce musculoskeletal disorders (MSDs), and evaluates the effectiveness of the solutions can lower worker exposure to risk factors and MSDs and improve productivity. A review of the Mine Safety and Health Administration (MSHA) injury/illness database indicated that 46% of illnesses in 2004 were associated with repetitive trauma and 35% of nonfatal lost days involved material handling during 2001? 2004. Even though these statistics show that MSDs significantly contribute to occupational illnesses and injuries in the U.S. mining industry, few mining companies have implemented an ergonomics process. Despite the many unique challenges in the mining environment, three mining companies partnered with the MSD Prevention Team at the National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory to demonstrate that an ergonomics process could be systematically implemented and effectively integrated with existing safety and health programs. Because these three mining companies were very different in organization, culture, and size, the ergonomics processes had to be modified to meet the needs of each company. A description of how these three companies applied ergonomics and the tools and training used to implement their processes is given. Prior to discussing the case studies, general information on the elements of an ergonomics process is provided.

Feb 1, 2009

By Chen Lin

Tectonic stress is an important parameter for understanding the dynamics of underground engineering and for the exploitation of coalbed methane. Multiple-period structural features usually have complex spatial relationships in tectonic superposition areas, which provides evidence for identification of the sequence of the tectonic stress period. Conjugated joints and slickensides are used to reconstruct the tectonic stress of the No. 8 Mine in Pingdingshan. Based on the geological unit division and field measurements, data on hundreds of joints and slickensides are collected from 33 stations. The tectonic stress results indicated by the conjugated joints show that there are mainly four directions of tectonic stress: NEE-SWW, NW-SE, NE-SW, and NNESSW. The tectonic stress results of the slickensides indicate that there are mainly four directions of tectonic stress: NNE-SSW, NNW-SSE, NEE-SWW, and NW-SE. According to the systematic analysis of the joints and slickensides, this paper separates the superposed joint and slickenside sets and identifies the tectonic stress periods with their abutting relationships. Three tectonic stress periods are determined and the sequence of the tectonic stress periods is NE-SW, NW-SE, and NEE-SWW. The results are consistent with other tectonic stress measurements for both the region and the locality.

By Chen Lin

Tectonic stress is an important parameter for understanding the dynamics of underground engineering and for the exploitation of coalbed methane. Multiple-period structural features usually have complex spatial relationships in tectonic superposition areas, which provides evidence for identification of the sequence of the tectonic stress period. Conjugated joints and slickensides are used to reconstruct the tectonic stress of the No. 8 Mine in Pingdingshan. Based on the geological unit division and field measurements, data on hundreds of joints and slickensides are collected from 33 stations. The tectonic stress results indicated by the conjugated joints show that there are mainly four directions of tectonic stress: NEE-SWW, NW-SE, NE-SW, and NNESSW. The tectonic stress results of the slickensides indicate that there are mainly four directions of tectonic stress: NNE-SSW, NNW-SSE, NEE-SWW, and NW-SE. According to the systematic analysis of the joints and slickensides, this paper separates the superposed joint and slickenside sets and identifies the tectonic stress periods with their abutting relationships. Three tectonic stress periods are determined and the sequence of the tectonic stress periods is NE-SW, NW-SE, and NEE-SWW. The results are consistent with other tectonic stress measurements for both the region and the locality.

By GA Harrison

The introduction of Extra Low Profile (XLP) mechanised equipment within Anglo Platinum is aligned with the overall New Mining Technologies strategy to focus on continuing modernization of our mining operations to achieve injury free sustainable production and cost effective mining technologies. The method allows for the introduction of a suite of XLP and Low Profile (LP) equipment in a narrow reef (1,2m) mining environment. For the first time it is now possible to achieve total trackless mechanisation at these stoping widths and XLP Breast mining has the potential to add more value when benchmarked with conventional mining and other mechanised methods. Various types of XLP equipment were tested at different sites within Anglo Platinum and this paper describes the XLP equipment evolution to-date. It concludes with recommendations on our future strategy regarding implementation and roll out of the XLP technology within Anglo Platinum.

Jan 1, 2008

By A. E. Raddatz

The Federal Bureau of Mines, as part of its goal to minimize undesirable environmental impacts associated with mineral processing, has investigated a soda-smelting technique for processing ilmenite into pig iron and a titanium slag that is suitable for a feed to a sulfate-process titania pigment plant. By this procedure, the generation of ferrous sulfate waste and its associated disposal problem is obviated. Molten titania slag was quenched, water leached, and filtered to yield a sodium titanate intermediate product containing about 70 wt-pct Ti02, 1 wt-pct Fe, and 20 wt-pct Na20. This intermediate product, high-soda titanate (HST), was mixed with H2S04, calcined, quenched, and water leached to produce a low-soda titanate (LST) product that contained only 2 wt-pct Na20. Both the HST and LST were evaluated as feed materials for preparing titania by the sulfate process. About 95 pct of the Ti02 was extracted from HST and LST by digestion in concentrated or 50-wt-pct-H2S204 solutions. About 95 pct of the solubilized Ti02 was subsequently recovered from the titanyl sulfate solutions by hydrolysis. Barren solutions from hydrolysis, containing about 26-wt-pct H2S04, were upgraded by vacuum-thermal evaporation or electrodialysis. The regenerated acid solutions were used to digest additional HST and LST.

Jan 1, 1979

By K Prendergast, P Dale, I Taylor, A J. Vigar, B Lueck

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Kainantu Project is located within the New Guinea Thrust Belt in northern Papua New Guinea. The area has a long history of exploration and production, with the discovery of alluvial gold in 1928 followed by the discovery of vein deposits of gold and copper at Kora in the 1950s and the current Irumafimpa vein gold mine. Current resources on the Kora-Irumafimpa Vein System (KIVS) stand at 1.5 Moz Au, 5 Moz Ag and 217 Mlb Cu.Mineralisation in the region includes gold, silver and copper associated with mid-Miocene age mafic to felsic intrusions. The KIVS occupies a broad north-west-trending mineralised zone more than 2.5 km long and 200 m wide, with the Kora, Eutompi and Irumafimpa veins on the western side and the Judd and Upper Kora veins on the eastern side. Economic mineralisation occurs in two closely related events occupying the same strongly structurally controlled shearing (quartz-Au-telluride veins and sulfide Au-Cu-Ag veins with free Au) and is best described as a significant intrusion-related event with both epithermal and mesothermal facets that does not appear directly related to known porphyry Cu-Au systems as seen at the surface. Significant wolframite is associated with vein quartz of a slightly older age but also occupies the same shear system.The KIVS occurs within a larger mineralised area of approximately 5 × 5 km. It has complex multiphase intrusions, breccias and diatremes that are only partly delineated by drilling and comprises multiple occurrences of Au-bearing veins and porphyry Cu-Au mineralisation. The area is considered to have high potential for extending the current resources and is being actively explored. The proposed recommencement of mining activities recognises the complexity of the KIVS and later disruptive faulting and will require tighter grade control systems, targeted mining techniques and a gravity circuit to maximise free Au recovery.CITATION:Vigar, A J, Lueck, B, Taylor, I, Prendergast, K and Dale, P, 2015. Kainantu gold-copper system, Papua New Guinea, in Proceedings PACRIM 2015 Congress, pp 601–606 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By N Clarke, G R. Ballantyne, M S. Powell, P Elms, A Anyimadu

AngloGold Ashanti Ltd nominated Sunrise Dam Gold Mine as a case study via their involvement with the long-running Australian Mineral Industry Research Association (AMIRA) International P9P research program (AMIRA, 2015) . A group of researchers from the Global Comminution Collaborative (GCC) conducted a comminution circuit survey and review together with a large group of graduate metallurgists, senior metallurgists and operators. Fundamental and applied research understanding was used to identify productivity and efficiency improvements around the crushing and grinding circuits. The limitations of current scientific knowledge were identified through this process and this will allow future research to be more focussed on what is required by industry.The comminution circuit at Sunrise Dam comprises three stages of crushing followed by two stages of ball milling. The secondary crusher and primary ball mill classification were identified as the primary limitations of the circuit. The secondary crusher was found to be underperforming through overall equipment efficiency (OEE) analysis and an improved chamber design was identified by Chalmers University. This improved design will promote higher power utilisation, choke feeding and a finer crushed product for the milling circuit. The primary ball mill product is classified by a combination of a trommel, 3 sieve bends and a hydrocyclone. The combination of poor classification and coarse, competent feed led to a situation where the primary mill was overfilled with rocks, reducing grinding rate due to cushioning of impact. Size specific energy (SSE) benchmarking methodology was used to identify that a 10% increase in throughput could be achieved with improved primary classification.CITATION:Ballantyne, G R, Clarke, N, Elms, P, Anyimadu, A and Powell, M S, 2015. Application of research principles to identify process improvement at Sunrise Dam Gold Mine, in Proceedings MetPlant 2015, pp 221–229 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By A. Eltringham

Operations downstream of mining and beneficiation are still being subjected to increasing scrutiny as highly capitalized projects have been either slow to achieve their targets or have actually failed to do so. Leaching and smelting projects have fundamentally high calls on capital and technology as reaction rates are increased and the capture and disposal of unwanted products are subjected to greater restrictions. Separating value from waste inherently becomes riskier as the purification of the desired product imposes greater demands on the process to produce benign wastes. When we superimpose on the chemistry of the project severe predictions of throughput rates, that bring in facets of manufacturing, we are introducing complexities that the records show are not handled well. This paper discusses some of the more common challenges that operators face and what methods are available and are likely to be successful in preventing the loss of value as projects are brought on-stream. This thinking needs to start much earlier and at greater intensity than our industry has normally chosen to employ.

Jan 1, 2011

By B. D. Pandey, D. Bagchi, Premchand

During the separation and recovery of metals from the ammoniacal leach liquor of Indian Ocean nodules by solvent extraction-electrowinning (SX-EW) in close-loop operation, the copper electrolyte containing ~40g/L Cu, 20 g/L Ni and 180 g/L sulphuric acid is bled-off to control the impurities. The recovery of copper and nickel as powders has been examined from the copper bleed solution following partial decopperisation, crystallization of mixed sulphate of the two metals and aqueous hydrogen reduction. From the dissolved sulphate solution containing 17.68 g/L Cu, 18.83 g/L Ni and 0.03 g/L Fe, the copper powder was precipitated at initial hydrogen pressure of 26 bar in an autoclave in 90 min at 140 °C. The residual copper from the spent solution was removed as sulphide and nickel powder was then recovered (99%) in two stages from a solution of pH 4.5 at 40 bar pressure and 190 °C. However, 98% nickel recovery in one stage was achieved when hydrogen reduction was carried out from an ammoniacal solution in the pH range 9-11. Copper and nickel powders were produced from the bleed solution with acceptable purity and specifications suitable for P/M applications.

Jan 1, 2004

By Jorge Castillo

This paper presents a dynamic analyses of heap leach pad stability under high phreatic levels and various levels of seismic loading. The dynamic analysis were conducted as fully non-linear two dimensional analyses with fully coupled liquefaction triggering using the Fast Lagrangian Analysis of Continua (FLAC) computer code. Also, the geotechnical parameters, appropriate earthquake record selection and modification, model calibration, numerical analyses and results are discussed.

Sep 12, 2005

The Australian Gas Light. Company was established in 1837, the first gas being sent out from the Kent Street Works, then the headquarters, in 1841. Mortlake Works were opened in 1886, and has since grown to the vast undertaking inspected by members of the Institute.The Kent Street Works were closed in 1921. The area of the, company's property at Mortlake is 117 acres.Some interesting figures from the statistics of the company's activities for 1937 are:-

Jan 1, 1938