Search Documents

By William H. Pomroy

The potential for large-scale fires in underground fuel storage and fuel transfer areas prompted the Bureau of Mines to study fire hazards in these areas and devise improved fire safety technology for use in these areas. This report describes the Bureau's research to characterize and quantify fire hazards in fuel storage and fuel transfer areas, develop guidelines for safe and efficient fueling system design, prepare specifications for automatic fire sensing and suppression systems for these areas, test prototype systems in the laboratory and in underground mines, and perform cost-effectiveness evaluations of the devised technology.

Jan 1, 1985

By David J. Hoadley

This report describes the development and limited testing of a semi-automatic, raise climber, Compact Service Hoist System designed for stope access in underground metal and nonmetal mines. Demonstrated capabilities of the system include a 1,000-lb payload capacity, control from the traveling cage and from up to three remote stations, operating in vertical or inclined raises 3 ft in diameter and up to 300 ft in length and a travel speed of 50 ft/min. The system has the capability of operating in crooked raises because the conveyance climbs two stationary wire ropes suspended down the raise. The drive unit is electrically powered with power and control signals supplied to the drive unit through an umbilical 'cable also suspended down the raise. The system has been designed for portability, ease of installation and minimum raise development. The hoist has been demonstrated successfully in an above ground test tower. This report provides a detailed description of the hoist design and its demonstrated performance to date.

Jan 1, 1985

By J. D. Davis

THIS-report gives results of in investigation of the carbonizing properties of 18 coals, including 2 from Alaska, 12 from British Columbia, 3 from Washington, and 1 from Utah. Each coal was carbonized in the standard 13-inch Bureau of Mines-American Gas Association (BM-AGA) retort at 900° C. Plastic properties were determined by the Gieseler and Davis methods, and agglutinating and free-swelling properties were determined by standard methods. Expanding properties were measured in the Bureau of Mines sole-heated oven. From the results of the tests on these single coals, three coals from the Crowsnest area in British Columbia, representing Elk River Nos. 4, 9, and 10, were selected for blending with the Utah coal, which was from the Lower Sunnyside bed, Horse Canyon mine, Emery County. Lower Sunnyside also was blended with Wilkeson -Nos. 2 and 3 (Washington) coals, Pocahontas No. 3 from McDowell County, W. Va., and the Oklahoma low-volatile coal used in the blend carbonized at, the Provo, (Utah) coke plant at the time this investigation was started. Most of the blends contained 3 percent hard pitch, which is the proportion used at the Provo plant. The blends were also carbonized in 13-inch BM AGA retorts at 900° C. High-volatile B coal from the No. 3 bed, Evan-Jones mine, Lower Matanuska, Valley, Alaska, yielded poorly fused coke or char. M-bed coal from the Chickaloon mine, Upper Matanuska. Valley, Alaska, ranked as medium-volatile bituminous and coked strongly. It expanded 39.6 percent in the sole-heated oven at a. charge density of 55.5 pounds per cubic foot..

Jan 1, 1952

U.S. Gold Commission Established. - The President, with the authorization of Congress, has named a gold commission made up of 17 individuals, most of them Government officials, to study U.S. policies related to the role of gold in domestic and international monetary systems and report its findings and recommendations to Congress. U.S. Lead Exposure Ruling. - On June 29, the Supreme Court upheld the Government's right to set lead exposure levels for employees at the workplace. The Court ruled in favor of the Occupational Safety and Health Administration (OSHA) in a challenge by a group that alleged that OSHA had failed to conduct a cost-benefit analysis prior to issuance of the lead standards. It was the Court's contention that Congress did not require such an analysis when it empowered OSHA to establish workplace standards. The petition to the Court was made by the Lead Industries Association Inc., Battery Council International Inc" American Iron and Steel Institute, St. Joe Minerals Corp., and other lead mining and consuming firms.

Jan 1, 1981

By D. Harrington

When the word "gas"' is mentioned in connection with mining almost invariably it is inferred that the explosive gas, methane, is in mind and that the reference is to coal mining. Although methane is likely to occur in any coal mine the metal mines of the world contain by far a greater variety of gases than do the coal mines. Often the gases in metal mines are as dangerous as the gases likely to be found in coal mines, and sometimes are even more deadly. A coal mine is more likely to contain methane than a metal mine. In rare instances it may contain high percentages of nitrogen or carbon dioxide or it may be deficient in oxygen where the air is confined in a blind end or in a sealed region. Much more rarely relatively small percentages of ethane or other hydrocarbons with an odor of ether, gasoline, or kerosene, or minute percentages of hydrogen sulphide are found in a coal mine. During a coal-mine fire or explosion carbon monoxide content is likely to be high (4 per cent or more), and if the coal contains much sulphur the high fumes may contain some sulphur dioxide.

Jan 1, 1931

By E. G. Kearnery

Introduction It is believed that the present paper will be of some interest, not because of any outstanding features of Renabie milling practice but because Renabie is the first gold mining property in a newly explored area - in Leeson and Rennie townships, Sudbury district, Ontario - to reach the production stage. The Renabie mill was originally designed by the General Engineering Company (Canada), Limited, as a 300-ton plant and went into operation in June, 1947, treating an average of only 128 tons a day for the balance of that year. Toward the end of 1948 the capacity of the plant was expanded to 450 tons a day, and the tonnage treated was gradually increased from the 1947 figure to the point where 420 tons a day was averaged for the first nine months of 1949. Description of Ore In general, the outstanding gangue component of Renabie ore is white quartz, which comprises at least 80 per cent of its total bulk and in some sections considerably more. Virtually all the gold occurs in very finely divided state; only very rarely has free gold coarser than 325 mesh been observed. The ore has a very low sulphide content, ranging from about 0.50 to 1.00 per cent by weight. The gold occurs both free in the gangue and ? locked in sulphides, the proportion of one to the other varying considerably from one orebody to the other. Pyrite is by far the most abundant sulphide, followed by galena, which, however, appears to be entirely absent in some of the orebodies. Minor amounts of pyrrhotite, chalcopyrite, chalcocite, and sphalerite have been noted. The ore appears to be entirely free, or almost so, of minerals containing arsenic, antimony, or molybdenum, and in general it could be described as free milling. The various hindrances to extraction of the gold which have been met with are believed to be due largely to the very finely divided state of the metal and to its intimate association with the sulphides and gangue. The ore contains silver, with the gold-silver ratio about 3:1.

Jan 1, 1950

By A. F. Marques

The Azores islands are located on a triple junction where the American, African (AFR), and Euroasian (EUR) plates meet. The Mid-Atlantic Ridge (MAR), oriented N-S, represents two branches of the T; an E-W branch defines the EUR/AFR boundary called the Terceira Rift. The nature and structure of this plate boundary, as well as the dynamics of the interaction of tectonics and volcanism remain unconstrained. The Azores plateau is seated on a mantle domain of anomalously low seismic S-wave velocities, and gravity and geoid anomalies, where the apparent thick crust is thought to relate to larger degrees of melting initiated at greater depths [1]. The cause of these anomalies is controversial but many authors consider the presence of an anomalously hot/wet enriched mantle probably supplied by a plume [2]. The geochemistry of the subaerial and most submarine lavas from the plateau reinforces the plume model beneath the Azores [3-4]. The origin, size and present location of the plume is under debate but an area near Terceira is the favoured plume centre [5]. [ ] SEAFLOOR HYDROTHERMAL SYSTEMS IN THE AZORES AREA (36ºN ? 40ºN) More than 150 active and fossil hydrothermal systems are known in the oceanic seafloor [6]. Many more are yet to be found on vast oceanic areas that haven?t been explored [7]. Ever increasing knowledge shows that modern seafloor hydrothermal systems can be hosted in felsic to ultramafic rocks, vary in size and shape and exhibit diverse amounts of sediment cover

Jan 1, 2011

The mineral Industry, following the economy as a whole, experienced little growth in 1992. However, with modernized plants, efficient workforces, and lower operating costs, the industry is well positioned to take advantage of possible improvement in the national economy during 1993. In addition to the significant 1992 events highlighted below, important events, trends, and issues within individual mineral industries are addressed in the commodity sections that follow. The value of processed materials of mineral origin is estimated to have been about $310 billion in 1992. The value of U.S. raw nonfuel minerals production in 1992 is estimated at approximately $32 billion, a 3% increase over 1991. The value of domestic minerals production has increased in all but 4 of the last 32 years.

Jan 1, 1993

By C. W., Davie

"DEFINITIONDiatomaceous earth consists almost entirely of the silicious remains of minute flowerless aquatic plants known as diatoms. The name diatomaceous earth, therefore, is to be preferred to others such as trade names, inappropriate terms, or names correctly applied to some other product. The following names should, therefore, not be used for diatomaceous earth,-- kieselguhr, infusorial earth, diatomite, celite, moler, bergnehl, English rottenstone, tripoli, tripolite, fossil earth, desmid earth, white peat, tellurine, randanite, ceyssatite, or any trade name.FORMATIONDiatoms live in practically all kinds of water, fresh or salt, hot or cold, still or running and under different conditions of depth and pressure. These minute plants assimilate inorganic salts from their environment and produce skeletons of silica much as mollusks secrete lime and form their Shalls. When the diatoms die they settle to the bottom together with anything else which may be present, such as sand, clay or volcanic ash. The organic matter gradually disappears leaving the silicious skeletons of the diatoms which, with impurities, make up the deposits of diatomaceous earth. These deposits which are still being foamed at the present time and which were produced throughout very different epochs, were more prolifically formed in the Tertiary, so that the thickest beds so far discovered are of that Age."

Nov 1, 1925

By S. L. Weber, D. E. Banks

"Silicosis was first reported by the ancient Greeks and is apparently as old as human history. The prevalence of this illness peaked in the last half of the 19th century and the early part of this century, when mechanized industry was developing and the relationship between dust exposure and disease was less well understood. Yet, even today in devel-oped countries, sporadic outbreaks of silicosis occur when workers are consistently exposed to silica particles of respir-able size (0.5 to 5.0 µm in diameter) at levels exceeding those recognized to be safe.Silicon dioxide or silica. is the earth's most abundant mineral. Silica is considered to be either free (i.e.. unbound to other minerals) or combined. Minerals with high amounts of free silica include quartz (including granite) flint. Chert, opal, chalcedony, and diatomite. Combined forms of silica are called silicates and include, among others, asbestos talc and kaolin.In the crystalline form, silica exists as quartz, cristobalite, and tridymite (Fig. 28). Of these quartz is ubiquitous in the environment and occurs as sand and as a part of many rocks. Cristobalite and tridymite occur naturally in lava and can be formed by the heating of quartz or amorphous silica. Cristo-balite is more tibrogenic than quartz. Amorphous silica is noncrystalline and, therefore, is relatively nontoxic and does not cause silicosis. It occurs as diatomite (skeletons of pre-historic marine organisms) or as vitreous silica (glass), the result of carefully melting and then quickly cooling free crystalline silica. Heating diatomite with or without alkali (a process known as calcining), forms cristobalite and adds the respiratory toxicity of free crystalline silica.There are many opportunities for occupational exposure to respirable crystalline free silica. Some of the commonly en-countered occupations in which the risk of silicosis exists are reported in Table 20.Silicosis. the pulmonary disease caused by the inhalation of silica particles of respirable size, is most commonly cate-gorized by findings on the chest radiograph. The most typical presentations simple silicosis and progressive massive fibrosis appear different radiologically but are grouped under the category of classic silicosis because they are a part of the radiographic spectrum of this illness. Radiographically, simple silicosis appears as small (less than 10 mm in diameter), rounded opacities, typically predominant in the upper lung zones. Progressive massive fibrosis is the result of the coalescence of these small nodular opacities and appears as larger opacities (more than 10 mm in diameter), again typicallydistributed in the upper lung zones."

Dec 1, 1995

By F. Habashi

The pioneer work on pressure hydrometallurgy was conducted in Russia at the end of the nineteenth, and the beginning of the twentieth centuries, by Karl Josef Bayer (1847-1904) and Vladimir Nikolyevitch Ipatieff (1867-1952), both working independently in Saint Petersburg. Bayer was studying pressure leaching while Ipatieff was studying the precipitation of metals and their compounds by hydrogen under pressure. Gradually, industrial applications took place first in the aluminium and later in the nickel industry. Today, the technology is well established in a large number of industries, such as uranium, gold, zinc, titanium, tungsten, and more recently copper.

Jan 1, 2004

The U.S. economy showed further strength during the third quarter of 1983, continuing the upward trend discussed in the last two issues of Minerals and Materials. The National Association of Purchasing Management composite index increased to a 10-year high of 67. 1 in July. (A value of 50 or greater indicates expanding industrial activity.) The index, a weighted composite of new orders, production, employment, vendor performance, and inventories, is derived from a survey of purchasing agents for about 250 industrial firms. Investment and Other National Economic Indicators The strong consumer surge of second quarter 1983 was reinforced during the third quarter by the performance of private investment. Because of this, many analysts became more optimistic about the strength of the recovery and its potential for being sustained. Capital investment growth, negative since 1980, was positive for every investment component in the third quarter of 1983. Preliminary estimates indicate a real increase of $1.4 billion (at an annual rate) in private investment expenditures on nonresidential structures, an increase of $4.3 billion (at an annual rate) for producers' durable equipment, and an increase of $4.8 billion (at an annual rate) in real inventory levels. The second quarter 1983 increase in expenditures on producers' durable equipment was the first indicator that investment recovery would occur during the rest of the year (table 1). Corporate profits in total manufacturing increased $6.5 billion from first quarter to second quarter 1983 (table 2).

Jan 1, 1983

Arsenic.--Inorganic arsenic has been added to the Environmental Protection Agency's list of hazardous air pollutants because of a high probability it can cause cancer. EPA estimates that inorganic arsenic emissions into ambient air total more than 6,000 tons per year, with about 65;L of this coming from the operations of copper, lead, and zinc smelters. Asbestos Detection.--In June 14, the President signed S. 1658 providing $172.5 million to detect and remove asbestos hazards in schools. Asbestos Use Must be Reported.--All firms using asbestos in the manufacture of some 30 categories of products must describe in detail how they use the mineral to the Consumer Product Safety Commission, for all manufactures since January 1, 1977.

Jan 1, 1980

A unity of viewpoint emerged from the workshop. The concept that transmission is via characteristic modes was a common theme in many of the presentations. Also, the confusion an the meaning of monofilar and bifilar to describe these dominant modes was cleared up. But, there was still a healthy divergence of opinion on what constitutes an optimum system. It was generally agreed that further analytical and experimental work is definitely needed. In particular, it was stressed that independent measurements of the constitutive properties of the electromagnetic environment are needed. Also, there was considerable concern that laboratory measurements of rock samples could lead to misleading results for the effective conductivities. Also, there was a general recognition that over simplified propagation theory should not be used to interpret field data. From a theoratical and practical point of view, it was realized that mode coupling plays a vital role in the transmission channel. One must not only understand which and how many propagation modes are excited by the transmitting antenna, but the conversion of energy from one mode type to another must be accounted for. This conversion can either be done intentionally (by fixed mode convertors) or non intentionally (by random wall roughness). In fact, mode conversion can be quite complicated when various propagation paths exist such as when insulated cables, leaky feeders, grounded rails, coal seams, etc. all convey portions of the electromagnetic energy. However, this state of affairs should be regared as an. opportunity for extended communication coverage in mines rather than a limitation of a desig. procedure based on preconceived notions of the dominant propagation mechanism.

Jan 1, 1978

By H. E. James

Much has been said and written about the need to reduce South Africa's dependence on gold. To compensate for the decline in the country's foreign-exchange earnings resulting from the phasing out of gold, which must inevitably occur at some future date, a far higher priority will have to be placed on the mining, beneficiation, and export of the 59 other mineral commodities produced in South Africa. The basic strategy of the mining and metallurgical industries should be to move from the traditional approach of establishing a resource base to the establishment of a market base; to turn from production orientation to market orientation; and to rely less on exploration and economies of scale and more on process innovation and product development. The enthusiasm, entrepreneurial spirit, and commitment of the leaders in the mining and metallurgical industry will clearly be of decisive importance in the establishment of new industries for the beneficiation and export of added-value mineral-based products. The State can make a significant contribution by the provision of a welldeveloped and efficient infrastructure, including rail and harbour facilities, communications and health services, roads, and of electricity and water supplies. In our search for a new development strategy for the beneficiation and export of South Africa's minerals, we need to recognize that no one nation has all the mineralresources that it needs. Commercial and strategic manipulation of mineral supplies should no longer be tolerated. The future of the human species lies in international cooperation and in a greater understanding of the limitations of the world we live in.

Jan 1, 1985

By Allen G. Gray

It's not news to you that the United States is highly vulnerable to potential problems in supply of critical and strategic metals, and that these metals - chromium, for example - are employed in important bearing alloys. It's also not news to you that there is a significant challenge to improve durability and life of bearing systems which contribute to conservation as well as productivity. The objectives of this workshop are to identify available technologies and opportunities for new technologies in conservation, substitution, and displacement of critical and strategic metals in bearing systems. These considerations are among the most viable options for reducing vulnerability to a cutoff of chromium and other critical metals and action should be taken to identify and develop those technologies now rather than after a crisis is upon us.

Jan 1, 1984

On April 5, the potlines at Consolidated Aluminum Corp.'s 35,000 ton-per-year primary aluminum smelter at Lake Charles, La., were frozen when natural gas lines were accidently cut by a dredge. Full production is expected to resume in 3 to 4 months. Three primary aluminum producers announced plans to restore much of the idled capacity in the Pacific Northwest as a result of a special power allocation by the Bonneville Power Administration. Reynolds Metals Co. planned to bring a total of 40,800 tons per year of capacity back onstream at Troutdale, Oreg., and Longview, Wash. The Aluminum Company of America (Alcoa) will restart half of a 23,500 ton-per-year potline at Vancouver, Wash. Kaiser Aluminum & Chemical Corp. planned to restart a 27,500 ton-per-year potline at Mead, Wash., and to bring an additional 10,000 to 20,000 tons per year back onstream at Mead and Tacoma, Wash.

Jan 1, 1980

CONTENTS PAGE INTRODUCTION AND ACKNOWLEDGMENTS. By George M. Fowler 2 Question 1-Is Structural Deformation of Some Character Always Necessary for the Migration of Mineralizing Solutions, Especially in Limestone or Other Dense Rock? DISCUSSION by: A. M. Bateman 10 S. F. Kelly 15 C. H. Behre, Jr 8, 13 G. B. Langford 13 T. M. Broderick 11 H. E. McKinstry 6 R. H. Clarke 13 D. H. McLaughlin 8 J. D. Forrester for M. H. Gidel . . . 4 W. H. Newhouse 13 G. M. Fowler 2, 6, 11 R. H. Sales 6 L. C. Graton 11 Edward Sampson 12 R. D. Hoffman 10 J. S. Stevenson 7 I. B. Joralemon 11 L. B. Wright 2 Question 2-What Are Some of the Chemical and Physical Characteristics in Cer¬tain Beds within a Limestone Formation that Determine Their Favorable or Unfavorable Aspects as Reservoirs for Ore and Other Introduced Minerals? DISCUSSION by: G. W. Bain 17 G. M. Fowler 21 C. H. Behre, Jr 21 L. C. Graton 18 J. S. Brown 16 G. F. Loughlin 18 E. L. Bruce 19 R. H. Sales 19 R. H. Clarke 20 A. K. Snelgrove 20 Question 3-Are There Any Criteria by Which One Can Determine When Min¬ing Operations Have Reached the Roots of an Ore Deposit? DISCUSSION by: J. M. Boutwell 29 G. B. Langford 29 T. M. Broderick 28 G. F. Loughlin 25 E. Y. Dougherty 27 R. H. Sales 24 G. M. Fowler 22 F. A. Thomson 26 I. B. Joralemon 22 Edward Wisser 30 General S. F. Kelly 35 References 36

Jan 1, 1940

1. Domestic Production and Use: In 1983, 12 companies operated 27 primary aluminum reduction plants, with 4 firms accounting for 65% of production. Washington, Oregon, and Montana accounted for 35% of the production; Indiana, Kentucky, Maryland, New York, Ohio, and West Virginia 35%; Tennessee, Alabama, South Carolina, and North Carolina 14%; other central States 16%. Based on published producer prices, output of primary metal in 1983 was valued at over $5.7 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Packaging accounted for an estimated 37% of domestic consumption in 1983, transportation 19%, building 17%, electrical 9%, consumer durables 8%, and other uses 10%.

Jan 1, 1984

By Louis, Jordan

THIS paper presents in an abbreviated form the chief points of interest in an investigation of the tarnish-resistant qualities of silver alloys, an investigation which has been carried out as a joint research by the Bureau of Mines and the Bureau of Standards and will later be reported in detail in an official publication from these bureaus. In 1923 a Commission of Gold and Silver Inquiry was created by a Resolution of the U. S. Senate to study the causes of the depressed condition of the gold and silver industry. In cooperation with this commission the Bureau of Mines made a preliminary survey to determine in what ways, if any, it might be possible to increase the uses of silver. One of the possibilities indicated by this survey was the development of silver alloys which should be non-tarnishing, or at least less-tarnishing, than the usual sterling silver (copper-silver). The preparation of a rather wide variety of silver alloys and the determination of their behavior under accelerated tarnish tests in the laboratory was therefore undertaken by the Bureau of Mines and Bureau of Standards as a joint investigation.

Jan 1, 1927