Search Documents

By J. E. Wey

Extraction of cobalt from cobalt sulfide and cobaltite flotation concentrate from the Blackbird Mine, Idaho, was investigated using an adapted strain of Thiobacillus ferrooxidans. Cobalt extractions as high as 100% were realized in the inoculated experiments, whereas only 4% extraction was obtained in the sterile run. The influence of pulp density on the rate and extent of cobalt extraction was also determined. It was found that the extraction of cobalt followed predominantly the indirect mode of bacterial activity. In this process, ferric iron oxidizes cobaltite to cobalt sulfate and ferric arsenate while being reduced to its ferrous state; the bacteria continuously re-oxidize ferrous to ferric iron. Electrochemical measurements using cyclic voltammetry suggested that cobaltite oxidation involved a number of intermediate reactions.

Jan 1, 1993

By Christina V. White

An experimental study was undertaken to investigate the feasibility of utilizing vapor transport for the treatment of heavy metal contaminated smelter soils. The focus of this project was to develop process chemistries that would make incineration a viable process for the treatment these soils. The experimentation concentrated on the elimination of arsenic, cadmium, and lead, and was performed in a laboramry scale rotary kiln setup. Three soil samples from non¬ferrous smelter sites, which contained various concentrations of contaminants, were utilized in the experimentation. Three chemistries were investigated for the volatilization of the heavy metals: Chloridizing volatilization, ferric chloride vapor complex formation, and the use of oxygen potential control. The samples were analyzed for residual heavy metals so that the extractions could be determined. However, the ultimate test was the leachability of the residual arsenic, cadmium, and lead, as determined by the TCLP test. The results firmly establish that incineration is a feasible process for the treatment of metal contaminated soils. It was found that no one process chemistry is suitable for all different soil samples. A two-step process consisting of a reducing step followed by a hydro-chlorination step was required to make Soil Sample-B pass the TCLP tests for all three heavy metals. Soil Sample-A passed the TCLP tests for arsenic, cadmium, and lead using a hydro-chlorination process at a minimum temperature of 700°C. In addition to passing the TCLP mm for Soil Sample-A and Soil Sample-B, 70 to 80 percent removal of the impurities was accomplished. This demonstrates that the leachability of the impurities was decreased primarily due to the removal of a large fraction of the contaminants, Soil Sample-C possessed very high levels of cadmium and lead and only moderate extractions of the impurities were generated from this soil. The arsenic TCLP test was passed at 500'C using a process gas containing ferric chloride and at temperatures of 700°C and above using chlorination of hydro-chlorination.

Jan 1, 1996

By Jennifer Mager, G. P. Martins, Dean Mussatti

"The role of lead, at low concentrations in high pH cyanide-electrolytes, on the dissolution behavior of gold, has been a topic of scientific and industrial concern for well over a century. The recent paper by Kondos et al [1] at CANMET (1995) this continuing interest and apparent importance. Nevertheless, the mechanism(s) by which this (and other heavy metal) component influences the electrodics of this electrochemical system has still not been unequivocally demonstrated. Instead, several plausible hypotheses, by pioneering researchers in this field, have been advanced and reiterated OVer the ensuing years. While it is generally accepted, based on equilibrium elctrode-potential calculations, that reduction (or co-reduction when oxygen is present in the electrolyte) of lead on the gold surface may occur due to cementation (contact reduction), the cemented lead has never been characterized. The work presented has reexamined the role of lead in this system, by delineating the species distribution of these system components and by interpreting the results of potentiodynamic studies in conjunction with SEM analyses of a gold electrode.1. INTRODUCTIONThe leaching of gold ores in cyanide electrolytes has been practiced for well over a 100 years. Research conducted on this topic has been primarily focused on the effects of operating parameters such as concentrations of oxygen and cyanide, and the pH of the electrolyte; or the leaching behavior of carbonaceous and sulfitic gold-bearing materials.Mechanisms by which pure gold is leached in alkaline cyanide media, with oxygen serving as the oxidant, have been subjected to continual examination and re-examination in the published technical literature during this century. Recently, it has been speculated that without the presence in the electrolyte of trace heavy metals, such as lead or mercury, that gold would not be leachable. Researchers who have tackled this topic, have either considered heavy metals to be a natural occurrence in these systems and ignored the role they may serve in the leaching process, or they have deliberately focussed on controlling their concentrations in the system to undetectable limits. As a result, conflicting findings have been reported for what would appear - depending on the details provided in these reports - to be identical systems."

Jan 1, 1997

By D. C. Foguel, J. L. R. Bravo

For several years, Caraiba Metais S.A. (CMSA) had to stock the arsenic sludge generated from the electrolyte purification process of its tankhouse. The amount stocked · reached approximately 3,500 tonnes, as the effects of its recycling during the smelting process and consequently in the sulfuric acid plant were unknown. Besides, it had as limiting factors the high content of arsenic in the copper concentrates supplied by foreign countries as well as the reduced capacity of the tankhouse's purification plant. The choice for selling the mentioned residue, which generally contains more than 50% of Cu, was attractive, but the environmental policies and regulations had not allowed this option. Other alternatives, such as the production of bicupric arsenic by means of a solvent extraction process or arsenic trioxide, were considered but the economic feasibility was not attractive due to the absence of a domestic market and a poor international market. After a study of the arsenic partition in the metallurgical process, it was verified that the residue could be recycled without causing any operational problems or damage to the environment. To make this possible, the capacity of the purification plant was increased and the way of removing the arsenic sludge from the cells was modified from manual to mechanical, therefore avoiding the direct contact of the workers with this poisonous substance. Moreover, procedures for recycling in the smelter were established and tolerance limits were set for both the smelter and the sulfuric acid plant. The main amount of arsenic to be recycled is released with the smelting furnace off-gas, which is washed during the purification stage of the sulfuric acid plant. The acid water, rich in arsenic, is then treated in the waste plant and the arsenic, in its stabilized condition, is confined in an appropriate area.

Jan 1, 2000

By Animesh Jha

Univariant diagrams are constructed for the reduction of nickel and cobalt oxide and sulphide minerals. The results from the carbothermic and hydrogen reduction of sulphide minerals are compared. The importance role of lime and calcium sulphate in controlling the emission of sulphurous- gases during reduction reaction is also explained. The mechanism of carbothermic reduction of nickel sulphide is explained by examining the sulphur exchange and reduction reactions. The phase equilibrium relationships that determine the formation of multicomponent liquid are characterised. Also the governing equilibria for inert atmosphere calcination- roasting of nickel and cobalt sulphide minerals are also described for the metallization of nickel and cobalt.

Jan 1, 1993

By Chikabumi Yamauchi, Masami Tashiro, Toshiharu Fujisawa, Hiroyuki Snano

"Rare earth metals usually contain large amount of oxygen because of their reactiveness, and therefore oxygen removal is one of the major problems on the purification of rare earth metals. In the present research work, halide flux treatment at high temperature under inert gas atmosphere was applied to the oxygen removal from neodymium. NdF3 was used as a halide flux. Deoxidation reaction and its mechanism were discussed based on the experimental results. Halide flux treatment is very effective for oxygen removal from rare earth metals.IntroductionSolid Sate Electrotransport (SSE) process has been successfully applied for the elimination of interstitial gaseous impurities from chemically active metals[l]-[5]. However, to achieve a higher effectiveness of the SSE process, it is required a very low initial impurity content in the metal. In case of rare earth metals, it is known that they usually contain large amount of oxygen that should be lowered as much as possible before applying the SSE process. In addition, if effective oxygen removal is achieved by simple process, it is significant also from the industrial viewpoint. In the present work, the application of a halide flux treatment is investigated to remove oxygen from neodymium by using NdF3 as a flux. At first, deoxidation reaction and its mechanism were discussed based on the phase diagram of the Nd-NdF3-Ndp3 quasi-ternary system. Based on the results, oxygen content in deoxidized neodymium was calculated theoretically and it was verified by deoxidation experiments."

Jan 1, 1998

By R. C. Hubli

Copper (II) chloride has proven to be an efficient lixiviant for copper sulphide ores and secondary sources of copper such as scrap. Nickel sulphides are generally associated with copper ores and copper-nickel matte is an intermediate product of processing mixed sulphides. While the copper species in aqueous chloride media are present as chlorocomplexes, the presence of nickel as Ni++ offers effective separation between the two by solvent extraction techniques. Oxidation of millerite by cupric chloride in sodium chloride solutions has been studied as a function of rate of agitation, leaching time, temperature, acid concentration and total initial cupric concentration. The reaction has a 1/2 order of dependence on initial cupric concentration in the range of 0.0 to 0.5M. The activation energy for the temperature range 333 -363 K has been found to be 59.2 kJ/mol with chemical reaction at the unreacted mineral surface as the rate controlling step. The rate expression, according to the shrinking-core model, for initial cupric concentrations between 0.0 to O.5M, is evaluated as

Jan 1, 1996

By Chao Lian, Hongxu Li, Hao Bai, Wei Wei

"Application of high-emissivity coating on inner walls in industrial furnaces increases the furnace thermal efficiency. The coating with high emissivity strengthens radiation heat transfer in the furnace, however, according to Wien's displacement law and Planck's radiation law, under heating temperature, the wavelengths of the radiation transfer are mostly between 1-5 µm, implying that increasing emissivity of the coating in near infrared band is more effective for higher thermal efficiency. In this paper, a new CuO-ZnO-based coating material sintered at 1600K was developed. The emissivity of the samples were measured and the result shows that, in near-infrared band, the emissivity of the sample reaches 0.98 at 773K with 13at.% of CuO doped in ZnO. In addition, the effects of CuO doping and use temperature on emissivity were also discussed. Furthermore, crystallization behaviors of ZnO-CuO sintering were investigated by DTA,XRD and SEM-EDS etc., which offered information for possible optimal design of the material.1. IntroductionIndustrial furnaces are widely used in various industrial heating. For example, the metal smelting furnace, ore sintering furnace in metallurgical industry; the distillation furnace, cracking furnace in petroleum industry etc,. The research on efficient energy saving technology has important significance. High emissivity coatings are widely used in many high temperature applications to effectively transfer the heat by radiation [ 1]. The theoretical calculation and experimental studies have shown that, coated high emissivity coating in the heating surface is an effective method to enlarge the infrared radiation power [2].At present, the infrared high emissivity coating has been widely used in China, and have been achieved remarkable energy saving effect. According to Wien' s displacement law and Planck' slaw, most energy of the black body at high temperature is radiated in the wavelength range of l-5µm; however it happens that many materials have the low emissivity within this range. Thus, it is important to improve the near-infrared band emissivity of materials [3]."

Jan 1, 2013

"In this paper, a mobile heat treatment furnace from Akkermans Gloeitechniek, a Dutch company, was simulated with Computational Fluid Dynamics (CFD). The furnace is cylindrical with four oil burners, and large metal products such as dredging pumps and impellers can be flexibly heat treated to obtain required microstructure and mechanical properties through stress relief, annealing, hardening and tempering. The furnaces are exposed to the open air, and thus the heat loss becomes significant and varies from day to day and from season to season. Since the temperature of the metal products to be heat treated can only be measured on the surface, the temperature evolution inside the metal could not be tracked in practice. CFD simulation provides a useful tool to predict the temperature evolution within the metal pieces and within the combustion space of the furnace. Energy distribution and heat loss can be subsequently estimated. An overall energy balance through temperature measurement indicted relatively low energy efficiency. Especially during the soaking period, the high energy supplied is barely used to compensate the heat loss of the furnace to maintain a constant temperature of the metal piece. The current CFD modeling aims to give advice on how to modify the design and optimize the operation to reach higher energy efficiency and low heat loss. The CFD model consists of turbulent combustion model, radiation model in participating media, and conjugate heat transfer between the combustion space and solid metal. Temperature measurement was carried out to provide thermal boundary conditions and overall energy balance of the operation. After the model validation with temperature measurement within the combustion space and metal surfaces, furnace optimization will be conducted.IntroductionHeat treatment is a common practice in metal production and manufacturing industries. Through heat treatment at certain temperatures with special patterns, unique mechanical properties of the metals and the metallic products could be obtained. ""Akkermans Gloeitechniek"" is a company situated in K.inderdijk, at location of LHC-Holland (www.ihccaland.com), the Netherlands. Heat treatment of metals is its core business. Various type of heat treatment are applied, such as stress relieving, soft annealing and hardening (quenching), tempering, transformation and precipitation. At the company 6 furnaces are in operation and the 7th is being built"

Jan 1, 2004

By David N. Hanlon

The effect of high-temperature plastic deformation of the austenitic phase (y) on the subsequent phase transformation to ferrite (a) has been experimentally investigated, and modelled using a physically-based model. The effect is of importance for steel sheet, in view of me significance of the phase transformation with respect to the eventual properties of the material. In this paper the kinetics of the y ? a phase transformation has been studied after different degrees of prior deformation. The degree of deformation is varied by applying different deformation temperatures and strain rates, and by allowing a varying extent of recovery and recrystallisation. Consequently, both dynamic and static recovery and recrystallisation have been involved. The dilatometric observations on the phase transformation have been modelled using an interface-mobility model, in which the effect of the dislocation structure is introduced as an additional driving-force term. The effect of the stored energy on the nucleation process, which appears to be affected more strongly than the growth of ferrite, is examined in terms of the classical nucleation theory.

Jan 1, 2001

By Ray Y. Lin

Chemical vapor deposition of tungsten carbide on the surface of steel has been investigated at temperatures between 400 and 550C in an atmosphere containing tungsten hexafluoride, hydrogen and benzene. The tungsten fluoride flow rate was maintained at 20 ml/min. The hydrogen flow rate was at 100 ml/min. The benzene concentration varied from 1.15 to 5.56% in the reaction gas. It was observed that the higher the temperature, the faster the deposition rate for tungsten carbide. But the dependence of the deposition rate on the benzene concentration was not systematic. From the x-ray diffraction analysis, it was observed that W, W2C and WC are all presented in the coating. The amount of each phase presented in the coating depends on the temperature and, to a less extent, on the benzene concentration. The microhardness measurement has also been done for all CVD carbide coatings obtained in this study.

Jan 1, 1992

By Gordon A. Irons, Diancai Guo

"Uneven movement of scrap during melting in an Electric Arc Furnace causes operation problems: cave-ins interrupt electric power input. The movement also influences the radiation heat loss to water-cooled side panels and roof. An apparatus has been built to simulate the flow of scrap that may be interlocked. It has been observed that flow starts at the point where the suspended length of the pile bottom reaches the average scrap size, and proceeds in the form of cave-ins, but scrap pieces slide with each other as ordinary granules. After a cave-in, the pile angle usually remains much larger than the normally observed angle of repose. The force balance of a partially suspended scrap pile has been analyzed, and the equivalent cohesion due to interlocking estimated. A numerical model has been developed to simulate the scrap flow. Simulated results agree reasonably with observed phenomena.IntroductionWhen one considers the melting of steel scrap in an electric arc furnace (EAF), it is helpful to understand the movement of the material during meltdown. As industrial experience demonstrates, scrap movement greatly affects EAF operation. In a typical operation, scrap is dropped into the furnace from scrap buckets. The roof and electrodes are swung into position, and power is applied to the electrodes situated over the scrap. The electrodes ""bore"" into the scrap by melting into the steel in the immediate vicinity of the electrodes as they are lowered. If solid scrap pieces gradually slide towards the arc area, the electric power supply can be maintained at a high level, with few interruptions or drastic electrode adjustments. This results in a high production rate and low power consumption per tonne of steel produced. On the other hand, if the charge moves down unevenly, i.e. in large surges, usually called cave-ins, the electrodes must be drastically raised, and power supply frequently interrupted. This is also accompanied by a high level of harmonics induced in the power network, deteriorating the quality of electricity supplied to other users.In addition, the movement of scrap in an EAF also influences the furnace heat efficiency, as the scrap pile is much closer to the electric arcs compared to the furnace wall and roof, and absorbs more radiated heat. Early exposure of the wall and roof to the arcs will increase the heat loss due to radiation, and reduce the service life of the furnace."

Jan 1, 2004

By Larry B. Fiske

Elimination of dust and processing of fines for both thermal and metallurgical coals is addressed. The efficiency of treatment with lignosulfonates compares favorably to oil in thermal coal. Effect of treatment with various lignosulfonates upon cokability of metallurgical coal was determined by Free Swelling Index, Gieseler Plasticity and Arnu Dilatation.

Jan 1, 1992

By T. T. Chen, J. E. Dutrizac

"Grooved cast Pb-Ag anodes are used by some zinc refineries to improve current efficiency. It was found that the manganese oxide scale formed on a grooved Pb-0.75% Ag anode consists mainly of MnO2, which occurs characteristically in rhythmically banded colloform structures and adheres to a layer of ""Pb02+PbS04"" that oxidized from the anode. The relatively homogeneous and nearly fracture-free morphology of the ""Pb02+PbS04"" layer suggests the relatively uniform corrosion of the anode. Deposition of the Mn oxide initially follows the contours of the anode surface, but the grooves eventually become filled with Mn oxide and gypsum. Hydrous Mn oxides and amorphous Mn oxides are believed to be also present in the manganese oxide scale. Tiny particles of PbS04 and SrS04, together with gypsum, other impurities and micro-pores, tend to concentrate in the grooves.IntroductionManganese is a common impurity in hydrometallurgical zinc processing circuits. The manganese originates from sphalerite (Zn,Fe,Mn)S and from the Mn02 added to the leaching circuit to oxidize ferrous ions [1]. Manganese in the sphalerite follows Zn through the roasting, leaching and purification processes, and is present as Mn(II) in the purified ZnS04 solution. The Mn in the added Mn02 is reduced to Mn(II) during the oxidation of the ferrous ions present in the leach solutions. In both cases, MnS04 is generated, and the MnS04 accumulates in the purified solution. In the cellhouse, Zn is plated at the cathodes to produce high quality metal. The Mn(II) is partly oxidized at the anode surface to Mn(IV), and the Mn(IV) precipitates as a scale on the surface of the anode and as a sludge on the bottom of the electrolysis cells. The presence of a thin layer of manganese oxide scale on the surface of the Pb-Ag anode can minimize the corrosion of lead and, accordingly, reduce the contamination of the electrodeposited zinc. However, a heavy manganese scale build-up can cause ""staining"" of the zinc deposits and reduced current efficiencies. Consequently, periodic anode cleaning to remove excess manganese oxide scale is carried out routinely in commercial operations."

Jan 1, 2011

By Y. Y. Sheng

Plume flows created by gas injection into liquid metals have been studied extensively, however the dynamics of bubbles within the plume have not received adequate attention, particularly for large, irregular bubbles, characteristic of the processing of liquid metals. The present model uses a combined Eulerian-Lagrangian approach in which an estimated void fraction distribution is used to calculate the liquid flow field with a conventional Eulerian scheme. The trajectories of bubbles are then computed in a Lagrangian manner using the estimated flow field, and experimentally measured information on bubble drag coefficients', lateral migration due to lateral lift forces and interaction with turbulent eddies, and variation in bubble size due to break-up. Turbulence in the two-phase zone is modeled with a modified k-e model with extra source terms to account for the second phase which have been recently determined by the present authors. The computed void fraction and turbulent liquid flow field distributions are in good agreement with experimental measurements.

Jan 1, 1993

By G. W. Barton

Process Systems Engineering (PSE) can be defined as the integrated usage of computer-based design and analysis tools. As such, PSE is becoming increasingly important in the chemical and petrochemical industries. This paper shows how a range of PSE techniques have been applied to the zinc electrowinning process. Topics discussed include model development, parameter estimation, steady-state and dynamic model applications, steady-state optimisation and neural network modelling.

Jan 1, 1994

By P. T. Velu

Solubility of metal oxides in the molten salt electrblytes is an important parameter in the electrochemical processing of metals and alloys. The efficiency of an electrochemical process primarily depends on the quantity of metal oxide present in the electrolyte in the dissolved form and its thermodynamic properties. The activity of CeO2 was calculated using the free energy of fusion of CeO2,{ AG°m, CeO2. The AGOm,CeO2 }was deduced from the values of enthalpy, heat of fusion and melting point of Ce02. The activity coefficients of CeO2 as a function of temperature and melt composition were calculated. The thermodynamic data such as integral molar enthalpy, entropy and Gibbs energy of formation were calculated as a function of composition and temperature.

Jan 1, 1994

By Kent D. Peaslee

When supersonic oxygen jetting is used in electric furnace steelmaking, the lance jet axis is typically inclined at larger angles to the vertical than is used in basic oxygen steelmaking. The supersonic jet is important not only for refining the steel, but for sustaining the foamy slag in the electric furnace. Physical modeling was carried out using a room temperature, two-dimensional slice apparatus in which mercury represented the metal and water-glycerol the slag. High speed video photography with image analysis was used to study the effects of the angle of inclination on the slag/metal bath. Mathematical modeling using FLUENT provided a method of predicting flow patterns and the trajectories of drops injected at various points in the flowfield. A one-half scale water model of the system, in which lance heights, angles, and flowrates simulated those encountered in steelmaking operations, was used to provide a better understanding of some aspects of the oxygen blowing process in electric furnace steelmaking.

Jan 1, 1994

By A. M. Blount

In 1983, a final ruling of the U.S. Occupational Health and Safety Administration (OSHA) specified that chemicals containing >0.1 % of a carcinogenic substance or > 1 % of a substance hazardous to health must be labelled. Amphiboles of the fibrous or asbestos-type must be quantified at levels of 0. I % whereas the status of non-fibrous types is not finally determined at this time. Tremolite and actinolite can possibly be measured to 0.1 % by XRD, but anthophyllite cannot be so measured. Recently the International Agency for Cancer Research (IARC) has designated quartz as a suspected carcinogen, and its quantity must be measured to the 0.1 % level. Thus, it has become Increasingly important to be able to detect and quantify minerals in bulk samples down to low or "trace" levels. It has been found that minerals needing to be quantified can often be concentrated by microcentrifuge and counted by means of polarized-light microscopy. For example, amphiboles in talc samples can be separated by using a heavy liquid (thallium formate-malonate) of density 2.810. Talc floats, and amphiboles sink. After centrifuging, the denser particles are removed from the bottom with a Pasteur pipette and placed in a clean centrifuge tube. Distilled water is added to the tube containing the denser minerals and the tube centrifuged again. After several washings with distilled water, the sample is removed along with a drop of water to a clean glass slide. A drop of 1 .584 refractive index liquid and a cover glass are placed over the dried sample. The slide is scanned for particles greater than 5 um in length and having an aspect ratio greater than 1:3. These are checked for refractive index, sign of elongation and extinction angle to differentiate them from talc particles on edge and other minerals. Amphiboles have all indices greater than 1.584, and talc has all indices equal to or lower than this value. Alternately the heavies at the bottom of the centrifuge tube can be filtered through a nucleopore filter. After the filter has been washed with distilled water and dried, a 1.584 refractive index liquid renders the filter transparent in two of the four extinction positions so that a count of amphibole particles can be made directly on the filter. The refractive index-density method which is so useful for talc powders should be equally useful for other nonsoluble industrial minerals.

Jan 1, 1989

By R. David Prenganan

RSR has developed a new environmentally superior process to recover lead as high purity electn:1o'i0!1 cathode from battery scrap. The process involves crushing the batteries, separating the lead bearing material from the plastic, ebonite and separators, and separating the active material (paste) from the metallic lead fraction. The paste is desulfurized using Na2C03 to convert the PbS04 to PbC03 and produce a sodium sulfate solution. The paste is further treated to decompose the PbO2 and PbC03 to Pbo. The PbO from the treated paste is easily leached, using H2SiF6 and electrown from solution using Pbo2?coated graphite anodes. The electrown lead has a purity exceeding 99.99%. RSR is in the final design stages of a plant to produce 36,000 tons per year of electrcwon cathode from battery paste in a new plant adjacent to the present Indianapolis refinery. This paper describes the work of a pilot facility operated in the early 1980's. The paper describes the patented process in detail and compares the newly designed environmentally clean electrolytic plant to present recycling plants.

Jan 1, 1990