Search Documents

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. This project is concerned with the determination of the effects of operating variables on the reaction of the particles. Experiments were carried out in a large laboratory-scale flash furnace with 72 wt-% Cu matte by varying initial particle size, temperature, oxygen partial pressure, oxygen-to-matte mass ratio and residence time. Chemical analysis was used to study the oxidation extent and copper volatilization. Particle fragmentation was examined. Fractional conversion and sulfur removal slightly decreased with initial particle size, while a higher oxygen-to-matte mass ratio mainly resulted in higher fractional conversion and more efficient sulfur removal. The fractional conversion values represented the overall extent of oxidation more closely than degree of sulfur removal.

Jan 1, 1997

By Rodney J. Ishak

The reduction of Mn3O4 to MnO has been investigated in a thermobalance apparatus. The charge was composed of manganese ore (decomposed by heating/calcination or pre-reduction to mainly Mn304) and coke. The material was charged to a crucible, which was suspended in the balance. CO-gas was distributed through a grid in the bottom of the crucible. Two sizes of ores were used; 2.4-4.8 mm and 6.7-9.5 mm. Coke particles were in the size range 4.8-6.7 mm. Experiments were conducted in the 900-1100°C temperature range. The composition of the product gas was monitored continuously. External mass transport between bulk gas and particle surface does not seem to limit the rate of reduction. Assuming that both diffusion through product layer and chemical reaction at the interface between MnO and Mn304 are rate controlling, the data was tried both in a shrinking core model and in a grain model using regression. The grain model gives the best physical description of the process, because the reactant is in fact a porous medium. With this model the effective diffusivity was calculated to be in the 1.5-6.10-5 m2/s range. The pore size was mainly between 0.1 and 10 um.

Jan 1, 2003

By M Kolbe

Co-Cu exhibits a metastable miscibility gap in the region of the undercooled melt. Specimens have been undercooled and solidified containerlessly into the metastable miscibility gap in an electromagnetic levitation facility (EML) and in drop tube (DT) experiments. Due to the high undercooling the velocity of the solidification front is very high and the microstructure is frozen in instantaneously. The microstructure of samples processed in the EML is influenced by the electromagnetic stirring due to the induction of electrical currents into the melt. A variety of microstructures has been observed. After undercooling below the binodal the liquid melt separates into the Co-rich L1-phase and the Cu-rich L2-phase. Two basic morphologies of the L1-phase can be observed, they can be attributed to the transition in dendrite growth from diffusionally and thermally controlled to only thermally controlled growth. Transient microstructures are observed after solidification in the vicinity of the binodal. Drop tube experiments, which lead to a rapid solidification of a distribution of droplets under reduced gravity conditions, in contrary allow for the observation of the early stages of demixing: the microstructure shows a homogeneous distribution of spherical particles of the minority phase in the droplets. The cooling rate of the droplets and its dependence on the droplet radius has been calculated. The solidification velocity as a function of undercooling has been measured in the EML for the composition Co-lB.Bat%Cu. The data are analysed in the framework of the LKTlBCT model with a velocity-dependent distribution coefficient as well as within a model of Galenko and Danilov using a kinetic growth coefficient of u=0.22 m/Ks.

Jan 1, 2002

By Kimio Itagaki, Makoto Ohtsuka, Kouki Chiba, Minoru Matsumoto

"The properties of Ni-Mn-Ga films such as chemical composition, crystal structure, microstructure and transformation temperature were investigated with respect to sputtering conditions in the present study. The Ni-Mn-Ga films were deposited on a polyvinyl alcohol substrate with a radio-frequency magnetron sputtering apparatus using the NisoMn2sGa2s and Nis2Mn:«1Ga24 targets. After separating from the substrates, the films were annealed at the temperature between 873 and 1273 K for 3.6 ks. The chemical composition of the films depended on the radiofrequency generating power, however, there was no dependence on the heat treatment temperature. Each deposited film had a columnar grain structure. After heat treatment, the width of columnar grains widened and then became indistinct with increasing heat treatment temperature. The Heusler type cubic crystal structure of the fi4n with heat treatment at 1073 K changed to the tetragonal one through the martensitic structural transformation during cooling. The martensitic structural transformation temperature increased with increasing nickel content of films, while the Curie temperature decreased. The film obtained at 200 W using the Nis2Mn24Ga24 target after heat treatment at 1073 K showed one-way shape memory effect through the reverse martensitic structural transformation during heating.IntroductionThe ternary intermetallic compound NiiMnGa has a Heusler-type crystal structure and is an intelligent material, which has a shape memory effect and a ferromagnetic property. The martensitic structural transformation occurs within the ferromagnetic temperature region. The cubic crystal structure of L21 at high temperature changes to a tetragonal one through the martehsitic structural transformation during cooling. The films of this compound can be applied for an actuator of micro-machines."

Jan 1, 2000

By Hongxu Li, Pu Liu, Hao Bai, Daqiang Cang, Lihua Zhao

"Coal, as the main energy in ferrous metallurgy, is consumed on a large scale and great amount of CO2 is emitted likewise. In this paper, a model, based on carbon balance, was developed for CO2 emission analysis, with data obtained from a typical integrated steelworks in China. The result shows that, CO2 emissions increase almost constantly with the growth of steel production. However, coals of different classes and product variety in the steelworks exerted an influence on CO2 emissions. Furthermore, three scenarios, including natural gas instead of coal for power generation, EAF process partly replacing integrated steelmaking, and feasible techniques applied to achieve lowest process energy consumption (FLPEC), were assumed to seek possible ways of carbon emission reduction. The result proves that the second scenario is most effective. If 40% of the steel product could be from EAF process, CO2 emissions would be reduced by 45.07%.IntroductionGlobal warming has become a global environmental problem, which is generally caused by excessive emission of greenhouse gases, such as CO2, generated from human activities and industrial processes. It is estimated that about 7% of global CO2 emissions was from iron and steel industry. Further, if the ore and coal’s mining and transportation are included, the CO2 emissions would reach 10%[1]. In general, the relationship between energy saving and CO2 emission reduction is positive correlation. However, in iron and steel enterprises, due to different types of energy resources like coal, heavy oil, natural gas, the consumption of which will generate different amount of CO2, are used, different energy consumption structure in iron and steel enterprises will lead to difference of CO2 emissions.In order to assess the CO2 emission reduction potential of China’s steel industry, Ke Wang etc.[2] developed a model using LEAP software to generate 3 different CO2 emission scenarios for the industry from 2000 to 2030. LEAP is a scenario-based software tool for integrated energy-environment and greenhouse gas mitigation analysis. The amount of CO2 emissions was obtained by the following equation:"

Jan 1, 2011

By T. Wang, R. G. Reddy

"The corrosion of stainless steel SS316L in a low melting point novel LiNO3-NaNO3-KNO3- NaNO2 eutectic molten salt mixture was investigated at 695K. After long-term isothermal dipping corrosion experiments, the SS316L samples were analyzed using scanning electron microscopy (SEM) equipped with energy dispersive spectrometer (EDS) to determine the topography and corrosion products. Dense and protective lithium iron oxide scale formed on the surface and prevented the SS316L sample from further severe corrosion. Therefore, SS316L is considered to be suitable construction material for solar thermal energy storage materials containers.IntroductionMolten salt mixtures have been considered as potential candidates for thermal energy storage and heat transfer media in solar energy applications. To apply the molten salt in the energy transfer process, the standard pipes made of stainless steel must be utilized to carry the molten salt mixtures in parabolic trough system of solar power production. The pipes encounter continuous flow of hot and cold molten salt every day. Thus corrosion of stainless steel in molten salt mixtures becomes extremely essential for the long-term utilization of the thermal energy storage media. The corrosion of passivity materials inside high temperature molten salt systems have been studied which gives fundamental understanding of basic mechanism about the corrosion process [1-8].The corrosion behavior of Fe-Ni-Cr alloys in an equi-molar LiNO3–NaNO3–KNO3 mixture was studied [9]. According to the XRD analyses, the major phases in the oxide scales were identified as LiFeO2, Fe3O4 and Cr2O3. A HITEC® salt mixture (NaNO3–NaNO2–KNO3) was also tested as a corrosion medium for stainless steel [10] and the corrosion rate was found to be affected by the protective oxide layer. In most cases, the alloys having more than 10wt% chromium show high resistance to corrosion in molten salts."

Jan 1, 2014

By Xuerong Wen

The oxidation behavior of TiAl3 intermetallics was investigated as a hnction of time at 1273K in pure dry oxygen. The oxidation experiments were carried out using TGA method. The oxidation scales were analyzed using SEM, EDS and X-ray diffraction methods. The structures of oxides formed at the different oxidation times were analyzed. The mechanism of oxidation of TiAl3 intermetallics was discussed.

Jan 1, 1998

By Xie Hao

According to its raw materials orthogonal test scheme is designed and a large number of systemic experiments were carried out in order to study the sintering characteristics of three types of fine ores in Kunming Iron&Steel Co.Ltd(KISC). The effects of carbon mixture ratio and basicity on sintering time, agglomeration ratio, physical properties and utilize coefficient were researched via single factor analysis and range analysis. The experimental results show the best mixture ratio of each fine ore. Analysis found that the influence of the carbon mixture ratio is more significant than which of the basicity on the sintering process except agglomeration ratio of foreign ore.

Jan 1, 2009

By Takao Yasugi

The majority of copper in the raw material migrates to the de-copperized dross that forms when the crude lead produced in the blast furnace is treated in the de-copperizing process. The de-copperized dross is treated in the electric furnace producing matte, speiss, and crude lead. The de-copperized dross also contains the silver. Therefore, it is important to improve the rate of silver migration to the crude lead. For this reason, the behavior of silver between the matte, speiss and crude lead phases was examined. At the same time, several tests to improve the percentage of silver migrating to crude lead were conducted.

Jan 1, 2003

By Jianjun Wang, Jiaqing Peng, Lingen Luo, Zhenbang li, Yinghe Lin

Copper removal from ferronickel by FeS has been exploring studied. It is found that the decopperizing agent FeS makes the copper removal in ferronickel effectively. The effects of FeS addition amount, carbon content in ferronickel and experimental temperature were investigated. The results showed that the removal rate of copper in ferronickel increased with the amount of FeS increasing. When the dosage of FeS is 20% (mass percentage)，the removal rate of copper can reach higher than 11%. The rate of copper removal rises with the amount of carbon content increasing in ferronickel. When the amount of carbon content is 1.86%, the removal ratio of copper is 41.3%. Higher experimental temperature promotes the copper removal reaction in certain extent. The flux is acidity and weak oxidative can also promote the reaction of copper removal.

Jan 1, 2015

By Jong-Jin Pak

The present work reports the commercialization of a recycling process of spent acid to recover molybdenum. The process consists of ammonia gas neutralization of spent acid containing molybdenum, crystallization and filtration of ammonium molybdate, roasting and hydrogen reduction of molybdic oxide to produce a commercial grade molybdenum metal powder. The mother liquor, highly nitrogeneous residual solution after the filtration of ammonium molybdate, can be utilized to produce chemical fertilizers.

Jan 1, 2006

By Marc Liebman

We present the results of a telephone survey of electric arc furnace (EAF) steel producers. This report characterizes the current status of EAF dust generation, treatment and disposal. It indicates the quantity generated, zinc content, other relevant constituents, and plans and trends that will impact on the quantity and characteristics of the dust generated. The survey covers EAF based steel producers in the United States and Canada. It identifies the processors currently employed, opinions about the use of these processors and services, as well as new technologies being considered.

Jan 1, 2000

By B. R. Baldock

The converting of high-grade nickel matte for production of low-sulphur matte or nickel metal is a process which has eluded metallurgists in the past because of the limitations of conventional converting furnaces. The high temperatures required and the refractory nature of nickel oxide has prevented practical success in a process which has been known to be theoretically feasible for a long time. The Ausmelt top submerged lancing system is capable of operating under close control of the smelting conditions. High temperatures and both rapid oxidation and rapid reduction can be achieved. These features have provided the basis for successful pilot plant trials of the desulphurisation of high-grade matte from the Kalgoorlie Nickel Smelter. Sulphur level in product was lowered from 20 to 25% to as low as 0.2%, with iron levels in matte in the range of 1.0 to 3.5%. The theoretical background of matte desulphurisation is surveyed and the pilot plant operations described. The implications of the results in relation to commercial plants and possible refinery operations are summarised.

Jan 1, 1993

By Chengxian Lui

Detailed mineralogical and metallurgical investigations were carried out on a phosphorous-bearing manganese carbonate ore from the Huayuan manganese mine, Hunan, China. Microprobe analyses indicate that the Manganese occurs mainly in calc-rhodochrosite and in rhodochrosite. The cOll'pOsitional range of these manganese carbonate minerals is 50 -80 % MnOJ3, 0 -35 % CaOJ3, 5-35 % MgC03 and 0 -15 F~. The manganese carbonate minerals are very fine grained, IOOSt are between 4.6 and 9.4 1m in diameter. The small grains are clustered into aggregates that form bands 0.5 to 10 rnn wide. The phosphorous-bearing mineral in the ore is fluorapatite and is in grains that are generally smaller than 6 1m in diameter. Metallurgical tests show that it is possible to concentrate the aggregates of manganese carbonate minerals by high intensity magnetic separation, and to reduce the phosphorous content by rpasting the concentrate to convert the manganese carl::x>nates to insoluble hausmannite, and then leaching the roast product with HCI to dissolve the fluorapatite.

Jan 1, 1989

By Jan Smit

Sulphidic copper concentrates are generally processed by pyrometallurgical means; while oxidative pressure leach processing of such materials has been shown to be technically feasible, there has traditionally been little incentive to choose this route in favour of a smelting option. However, for concentrates with elevated arsenic levels, oxidative pressure leaching offers distinct advantages, as smelter air emission standards and restrictions on concentrate importation have tightened. The current state of pressure leach technology allows for high copper extractions from arsenical copper concentrates, while producing an environmentally stable process residue, without atmospheric emissions of sulphur dioxide or arsenic. In its studies on pressure leaching of copper concentrates, Sherritt has shown that arsenical feed materials can be converted into environmentally stable residues, with excellent copper extractions. The results of recent batch and pilot plant test work are discussed, including the deportments of copper, arsenic and precious metals.

By Heikki K. Jalkanen

Thermodynamic properties of copper-iron mattes and slag-matte distribution of copper and some minor matte constituents (Ni, Co, Mo, As, Sb and Bi) are discussed on? the basis of equilibrium measurements: a change from. oxidic to sulfidic solubility as the predominant form of dissolution of copper takes place as matte grade decreases. Distribution coefficients of minor matte constituents are complex functions of sulfur and/or oxygen potentials?. The distribution behaviour of different? metals can be qualitatively derived from their affinities to copper and stabilities. of their sulfides and oxides. The equilibrium results are compared with commercially observed values. from Outokumpu.Oy flash smelting furnace.

Jan 1, 1983

By Lori Bassman, Cassandra George, Cullen McMahon, Md. Zakaria Quadir, Michael Ferry

"Complete and accurate analysis of subgrain microstructural features must include three-dimensional information. Three-dimensional electron backscatter diffraction (EBSD) data can be used to characterize these features; however their boundaries first must be determined. This cannot be accomplished simply with pixel-to-pixel misorientation thresholding because many of the boundaries are gradual transitions in crystallographic orientation. Fast Multiscale Clustering (FMC) is an established image processing technique that we have combined with quaternion representation of orientation to segment this kind of data. Segmentation algorithms often have issues handling images with both distinct and subtle boundaries. Our implementation of FMC addresses this by using a novel distance function and statistical analysis to take into account the variance in orientation of each feature. Although FMC was originally a twodimensional image processing algorithm it can be generalized to analyze threedimensional data sets. As an example, a segmentation of microbands in cold-rolled aluminum is presented.IntroductionThree-dimensional electron backscatter diffraction (3D-EBSD) is a method for mapping the local crystallographic orientations of points in a volume. The technique uses a dual beam platform consisting of a focused ion beam (FIB) and SEM with EBSD, where FIB is used for serial sectioning and EBSD for orientation mapping of 2D slices. These 2D slices may then be stacked to create a 3D volumetric data set.Typical uses of such a data set include characterizing the geometries and crystallographic orientations of surfaces between structures in 3D [1-5]. This involves identifying boundaries accurately, either in 2D slices with subsequent 3D reconstruction (as illustrated in Figure 1) or in the 3D data set. All such data sets present the challenges of i) aligning data slices to correct for instrument drift, ii) identifying relevant boundaries, and iii) implementing appropriate smoothing or interpolation algorithms. The focus of this paper is boundary identification."

Jan 1, 2011

By Yapeng Zhang, Zhiwen Shi, Chaoquan Yao, Fei Wang, Xinyu Li, Jianliang Zhang

A great deal of iron ores which have special elements have been applied in the sintering process with the decreasing of high-grade quality iron ores resources. In this paper, the laterite nickel ores were added into three different kinds of iron ores respectively to make liquid phase formation research by software of Factsage and high temperature characteristic sintering experiments. The results showed that the adding proportion of laterite nickel ores should be less than 15% when the high temperature properties of the mixing ores were well. Increasing the mixing ration of laterite nickel ores in the sintering blending would play an important role in the reduction of the sintering cost.

Jan 1, 2015

By M. A. Gimenes

The utilization of chlorination in extractive metallurgy and advanced ceramics areas has been widely investigated as a preparative route in order to obtain intermetallic compounds, which are used as precursors in the development of new materials and process. The major processes of decomposition of rare-earth ores use sulfuric acid and sodium hydroxide at high temperatures, however there is not much work concerning chlorination. In this work, a systematic study of the reaction between xenotime (REPO4), chlorine and carbon has been performed. Particular emphasis was on kinetic studies to establish optimized conditions for the reaction. The kinetics of chlorination of xenotime raw material by rare-earth elements/compounds has been studied over a temperature range from 600°C to 950°C. The influence on the rate of conversion of xenotime to RECl3 on temperature, partial pressure of chlorine, carbon content, and particle size were investigated. A global rate equation that includes these parameters has been developed. The results show that the process follows the unreacted core-shrinking model with a formation of a porous product layer. The powder X ray-diffraction technique corroborated this model showing clearly the patterns related to the formation of yttrium oxychloride (YOCl), indicating that the reaction mechanism involves the presence ofan intermediate step before the formation of lanthanide chloride.

Jan 1, 2000

The present work is mainly focused on developing intermetallic inert anodes for aluminum electrolysis. The anode alloy based on Al-Ti-Cu system was prepared by casting, followed by the application of a protective coating. Behaviour of corrosion and the passivation under anodic condition was characterized using the electrochemical and microscopic techniques. The results obtained clearly demonstrate that the oxide coating can provide good corrosion resistance via surface passivation of alloy anodes, rendering them inert in cryolite melt.

Jan 1, 2006