Search Documents

By Christopher J. Bise

PRINCIPLES OF MINE PLANNING During the initial planning stages, all mining operations are analyzed and evaluated in a similar fashion. This similarity holds true because the mine-planning procedure can be reduced to a network of interrelated systems that are tied together by a common philosophy of mine planning: namely, that the resource is to be extracted in a manner which is safe, efficient, and profitable. The success of the mining operation cannot be guaranteed unless each of these three requirements is met. Fig. 1 shows a flowchart for the initial planning of any mining operation. Notice that there is a preplanning stage that leads to the planning of four interrelated systems. The preplanning stage includes property exploration, estimation of production and manpower requirements, and the establishment of construction timetables. The four systems, evaluated after the pre-planning stage, are broken down into the following: (1) Excavation and handling system, (2) Strata control system, (3) Operating support system, and (4) Service support system. The Excavation and handling system includes the selection of all the equipment for the removal of the resource from its in-place deposit (e.g., draglines, continuous miners, rock drills, etc.) and for the transportation of the mined material from the face (e.g., belt conveyors, trucks, etc.). The Strata control system incorporates all those considerations which maintain the integrity of the roof, ribs, floor, and overburden both during and after the extraction phase; typical considerations in this area include pillar sizing, artificial support of the immediate roof in mine entries, and subsidence protection. The Operating support system contains the "necessary evils" of mine planning; the system consumes a large percentage of the mining engineer's planning time but does not contribute to the actual extraction of the resource. However, if proper attention is not paid to the various components of the system, such as ventilation, drainage, and power, then the mining operation will not perform to its capabilities. Finally, the Service support system is composed of those operations which keep the mine running efficiently; typical examples of these include maintenance and sup- ply. One important concept that Fig. 1 is designed to emphasize is that the four systems are interrelated; typically, a slight alteration of one can affect the performance of another. If these interrelationships are ignored, the effects on the system can be disastrous. The mine preplanning stage and the four subsequent system evaluations constitute the Analysis portion of the mine planning flowchart. After this portion of the study is completed, the overall projected operation can be evaluated by techniques such as financial analysis. This last step in the study is referred to as the Synthesis of the previously calculated parameters into an overall plan. Much has been written about the overall evaluation of mining properties, but, over the past thirty years, very little has been written about the analysis of mine- planning systems in a coordinated manner. Further, those texts which attempted this topic have failed to give sufficient examples for successful implementation, thus supporting the operating engineers' lament that it is easy to discuss theories but difficult to show applications. This text is intended to bridge this gap. Examples of the various stages of the analysis portion of the mine planning flowchart shown in Fig. 1 will be covered in this text, with the exception of the Service support system, since this system is oriented more toward day-to-day planning than long-term mine planning. INTERNATIONAL STANDARDIZATION The benefits that can be derived from an international standardization of the units used in mining engineering calculations are numerous. The interchange- ability of equipment parts and the ability to analyze and compare performance and design specifications on an equal basis are just two of the goals desired by both manufacturers and mine operators. Unfortunately, conversion to an international standard has not been rapidly achieved by engineers in the United States, due to their training under the English system. The Society of Mining Engineers of AIME has made the commitment for the adoption of the Systeme International d'Unites (SI) in all mining engineering calculations. Since many practicing mining engineers and students in undergraduate programs still find difficulty in relating to SI units, the calculations in this textbook will use the English system, with Table 1 available for conversion into SI units.

Jan 1, 1986

The Mining Foundation of the Southwest (MFSW)promotes public understanding and education related to the mining industry. Towards this goal, the Foundation has funded several projects from donations and fundraising activities. The MFSW was incorporated in 1993 by combining the Mining Club of the Southwest and the Mining Club of the Southwest Foundation. The Mining Club began in 1971 as a social organization. It provided members of the mining community an opportunity to meet. The club also provided a means for public education about mining. In the early 1990s, the club’s efforts were directed mainly toward educational activities. And in 1992, discussions began concerning incorporation into a non-profit foundation to further the public understanding of mining. In 1983, the American Mining Hall of Fame was inaugurated to honor significant contributors to the industry and profession. The Hall of Fame serves to educate people about prominent persons associated with the mining industry, present and past. The honorees number 75. Plaques commemorate their induction and are on display at the Arizona Historical Society’s Museum in Tucson, AZ. The combined honors ceremony and banquet have remained one of the fund raising activities.

Jan 1, 1999

By Steve Chorley

Open-type, or main beam, tunnel boring machines (TBMs) can achieve impressive rates of production. This type of TBM typically outperforms other types of TBMs currently in use around the world. In good ground conditions, main beam machines have achieved production rates of more than 1 km/month (0.6 miles/month). However, installing effective ground support in poorer rock conditions on main beam machines can be a major cause of concern. The design of main beam machines is such that installation of ground support equipment, particularly at the front of the machine in what is commonly known as the L1 support zone, has traditionally been limited to rock drills and basic working platforms. Personnel working in the L1 zone have, until recently, been protected by roof supports and extended fingers, often with restricted access to working areas.

Jan 1, 2011

By Antonio Rivera

On Nov. 13, 1985, Colombia's Ruiz volcano erupted, killing an estimated 25,000 people and burying several villages. Damages were estimated to be about $US300 million. The following is an account by SME member Antonio Rivera of the volcanic activity that led to the eruption. His account also includes a description of the geography and some geology of the affected area. Mining operations in the area were mostly unaffected, although some operations were forced to close until the roads leading to them could be repaired. Introduction The Ruiz volcano is located on the Central Cordillera of Colombia about 28 km (17 miles) southeast of Manizales, the capital of the state of Caldas. Ruiz is one of nine volcanoes that form a complex volcanic chain within the middle portion of the Central Cordillera. The Cordillera has 30 other volcanoes in the southern part of Colombia. Ruiz volcano Ruiz's elevation is 5200 m (17,060 ft). It is covered by an ice cap estimated to be 20 m (66 ft) thick at its summit, an area that covers 17 km2 (6.5 sq miles). Drainage is composed of several rivers that flow into the Magdalena River on the east and Cauca River on the west. The rivers flowing to the east are Guali, Azufrado, Lagunillas, and Recio. The rivers that flow to the west are Claro, Molinos, and Chinchina. There is a road from Manizales to El Refugio, a ski area located on the northeast flank of the volcano at 4800 m (15,750 ft) in elevation. The Ruiz volcanic complex was built in two stages. The first is a shield type of volcano (mainly lavas) formed about a million years ago. The second is a younger stratovolcano overlaying the ancient one. It consists of lavas and pyroclastics and was built over the past 500,000 years. Twenty-four eruptions of Ruiz are known to have occurred during the last 14,000 years. Its products mainly consist of lava flows, pyroclastic flows, mudflows (lahars), and directed lateral explosions. Historic eruptive record 1595 - Debris avalanche, blast, pyroclastic flows, mudflows, ash flows, and ash fall. 1828-1829 - Ashes (phreatic). 1831-1833 - Gas emissions and ashes. 1845 - Mudflows and pyroclastic flows. 1985 - Sept. 11- Fumarolic activity, phreatic eruption, ash fall, and small mudflows. 1985 - Nov. 13 - Ash and pyroclastic fall, major destructive mudflows (magmato-phreatic eruption). From 1845 through 1984, Ruiz volcano always had a slight fumarolic activity. It was restricted to the crater area. In November and December 1984, the fumarolic activity increased and the first ash emission and vapor-sulfur formation started. Small local earthquakes accompanied these volcanic activities. The volcano had a small erup¬tion on Sept. 11, 1985. It was manifested by phreatic explosions that ejected fragments of the vent and formed ash deposits 25 mm (1 in.) thick around an area 2.5 km (1.5 miles) from the crater. Fine material was blown by the wind and reached Manizales and neighboring areas, producing a small layer of ash up to 10 mm (0.4 in.) thick.

Jan 2, 1986

By A. B. Cecala

Video technology coupled with data logging exposure monitors have been used to evaluate worker exposure to different types of contaminants. However, previous application of this technology used a stationary video camera to record the worker?s activity while the worker wore some type of contaminant monitor. These techniques are not applicable to mobile workers in the mining industry because of their need to move around the operation while performing their duties and tasks. The Helmet-CAM is a recently developed exposure assessment tool that integrates a person-wearable video recorder with a data logging dust monitor that are worn by a miner in a backpack, safety belt, or safety vest to identify areas or job tasks of elevated exposure. After a miner performs his or her job while wearing the unit, the video and dust exposure data files are downloaded to a computer and then merged together through a NIOSH-developed computer software program called EVADE (Enhanced Video Analysis of Dust Exposure). By providing synchronized playback of the merged video footage and dust exposure data, the EVADE software allows for the assessment and identification of key work areas and processes, as well as work tasks that significantly impact a worker?s personal respirable dust exposure. The Helmet-CAM technology has been tested at a number of metal/nonmetal mining operations and has proven to be a very valuable assessment tool. Mining companies wishing to use this technique can purchase a commercially available video camera and an instantaneous dust monitor to obtain the necessary data, and the NIOSH-developed EVADE software will be available for download at no cost on the NIOSH website.

Feb 27, 2013

By G. C. Presley

Estimated domestic production of pumice and pumicite in 2004 increased about 23 percent since 2003, according to the U. S. Geological Survey (USGS). The USGS estimate of domestic production of 687 kt(757,000 st) for 2003 turned out to be 870 kt (959,000 st)of actual production. The USGS estimated the value of pumice and pumicite sold or used in the United States to be $26 million in 2004, up $4 million from the value in 2003. There was an estimated decrease in the mine, or mill, average price to $24.14/t ($21.90/st) in 2004 from $25.19/t ($22.85/st) in2003.

Jan 1, 2005

By Peter White

The Hemlo Gold District, located on the north shore of Lake Superior, was discovered in 1981 and will become one of the largest gold mining camps in Canada. Three major Canadian mining companies are presently developing large orebodies and are scheduled to commence production at various times through 1985 and 1986. This paper describes the types of shaft sinking equipment and technology being used by contractors in constructing the required shafts to depths below 1000 metres. The principal shaft design criteria, types of shaft sinking machinery and relevant manpower allocations are discussed.

Jan 1, 1985

By M. Rossi

Geologic ore controls are usually interpreted and modeled from cross sections and plans, as they are critical to construct meaningful and accurate ore reserves models. The geologic boundaries are often modeled as two-dimensional surfaces or three-dimensional solids and used as hard boundaries to constrain the grade estimates. In many cases, the geologic model is the most important factor in estimating the mineralized tonnage predicted by the reserves model, since it is generally drawn to separate the volumes of mineralized and waste material within the deposit. Because geologic models are interpreted from widely spaced drill hole data, the accuracy of the contacts of the different zones modeled could be poor. The lack of accuracy in the definition of geo-logic zones can have a significant impact on a resource model. In this paper it is shown that the geologic interpretation can and should be checked for potential biases. In particular, an unbiased overall volume of the original drill hole information with respect to the resulting solids and codes assigned to the block model is sought. In addition, geostatistical conditional simulations can be used to simulate the geologic attributes modeled, thus providing an alternative view of the geology, and a measure of the uncertainty of the geologic boundaries. The simulated geologic model provides an assessment of the impact of alternative geologic interpretations on the over-all uncertainty of the reserves model. In the case study presented here, the uncertainty of the geologic model is quantified for a difficult-to-model, high-grade copper deposit in northern Chile.

Jan 1, 2004

By Ralph van Rijswick, Erik Vlot

"Anglo American operates 18 Weir GEHO piston diaphragm pumps (PD) in the two pump stations of the 52-km (32-mile) long Minas Rio iron ore concentrate pipeline. The pipeline is designed to transport 26.5 Mt/a (29.2 million stpy) of concentrate from the mine to the export terminal at the coast.During the commissioning of the pipeline in the fall of 2014, high pressure pulsation levels were experienced, with peak-to-peak levels as high as 20 bar. Based on pressure readings it was concluded that hydraulic resonances were present in the system, which were excited by the third and sixth harmonic of the flow pulsation generated by the pumps.Based on this observation, Weir Minerals Netherlands, manufacturer of GEHO PD slurry pumps, recommended installing a phase shift controller that controls the phase shift between the crankshafts of the individual pumps, thereby minimizing the effect of the hydraulic resonances.GEHO piston diaphragm pumps and pressure pulsation analysisPiston diaphragm pumps are used worldwide to transport abrasive and/or aggressive slurries against high discharge pressures in the mining, mineral processing and power industries. The basic operating principle of a piston diaphragm pump is shown in Fig. 1.A crankshaft is driven by an external electric motor via a gearbox. The crank mechanism transfers the rotating motion of the crankshaft into a reciprocating motion of the piston. The piston displaces a hydraulic fluid, called the propeling liquid, which displaces an elastic rubber diaphragm. When the piston moves to the right, the pressure in the pump chamber drops below the suction pressure and the nonreturn valve on the suction side will open, allowing the pumped fluid to flow into the pump chamber. When the piston moves to the left, the fluid is compressed, and when the pump chamber pressure rises above the pipeline pressure, the nonreturn valve on the discharge side will open allowing a displacement of fluid into the discharge line. The main objective of the diaphragm is to isolate the piston and the drive mechanism from the abrasive and/or aggressive fluid and create a hermetic seal between the pumped fluid and the ambient environment. Piston diaphragm pumps as shown in Fig. 1 are among the largest positive displacement pumps in the world and have been produced with stroke volumes of up to 100 L (26 gal) per pump chamber for flow rates up to 800 m3/h, discharge pressures up to 250 bar and hydraulic outputs over 2 MW per unit (van Rijswick et al., 2010)."

Jan 9, 2017

By B. McNulty

The Niblack polymetallic volcanogenic massive sulfide deposits are located on Prince of Wales Island in southeast Alaska, approximately 50 km southwest of Ketchikan. The property hosts a number of polymetallic volcanogenic sulfide occurrences within the folded Lookout rhyolite volcanic succession. The Lookout deposit is the primary focus of current resource delineation and contains an indicated resource of 4,136,000 tonnes at 1.13% Cu, 2.32 g/t Au, 2.27% Zn, 38.70 g/t Ag and an inferred resource of 1,736,000 tonnes at 1.09% Cu, 1.77 g/t Au, 2.02% Zn, and 25.52 g/t Ag as of March 2011. Sulfide mineralization is interpreted to have formed sub-seafloor, within permeable felsic fragmental volcanic rocks. Sulfide minerals of economic interest include chalcopyrite and Fe-poor, Zn-rich sphalerite. Of considerable importance, the Lookout deposit contains elevated gold that occurs as inclusions within the base metal sulfides.

Jan 1, 2012

By C. Bazin

Grinding circuits are operated in the presence of disturbances due to ore changes and equipment malfunctions. One of the challenges faced by the operators is the detection of a disturbance, the identification of its origin and of the action to correct the problem. Hydrocyclones overloading, worn or partly plugged apexes of the units of a nest, surging and internal liner detachment may cause a loss of classification capacity and quality leading to a less efficient grinding operation. A dynamic simulator is used to assess rules for the diagnosis of hydrocyclone faults from the trends produced by sensors.

Jan 1, 2009

By John A. Breslin

The year 2010 will mark the 100th anniversary of the beginning of the research efforts by the U.S. government to improve the health and safety of miners working in the United States. This research began in 1910 with the establishment of the U.S. Bureau of Mines (the Bureau) and it has continued during the past 10 decades, even after the closure of the Bureau in 1996. The research on safer mining technology, formerly done by the Bureau, has now been combined with National Institute for Occupational Safety and Health (NIOSH) studies of miners? health to form a unified federal research program to improve the health and safety of miners. This article describes this research and places some of the accomplishments into perspective with other activities in the U.S. Mine Safety and Health Time Line (insert).

Jan 1, 2010

By Keith Schaeffer

This paper presents a history of the planning, engineering and construction completed for the railroad tunnel crossing part of the West Elizabeth Avenue Storm Drainage Project, undertaken to relieve flooding within the West Elizabeth Avenue area in Linden, NJ. The Railroad Crossing Contract is part of the larger Linden Drainage Improvements Project consisting of a new gravity storm sewer system. The improvements are required to provide additional storm drainage for the City of Linden and the Merck Pharmaceuticals manufacturing facilities in the City of Linden.

Jan 1, 2008

By Steve Kral

MINExpo INTERNATIONL 2000 was a good place for companies to introduce new products, technologies and services to the mining industry. Caterpillar took that a step further. The company hosted a one-day preview of its mining products at its Tinaja Hills Training and Demonstration Center near Tucson, AZ. About 30 members of the trade press spent the day at Tinaja Hills before heading on to Las Vegas for MINExpo INTERNATIONAL 2000. Dozens of Caterpillar professionals provided the editors with a first-hand look at Caterpillar’s mining trucks, loaders, excavators, road graders, water trucks and engines. In addition, these Cat experts explained the intricacies of each piece of equipment, the latest technology that led their improvement and their value to the company’s mining customers.

Jan 1, 2000

By V. L. Franzen, Z. J. Hladysz, C. A. Kliche

The Wharf Resources mine, located in the Bald Mountain Mining District approximately 6.4 km (4miles) west of Lead, South Dakota, has operated a surface gold and silver mine and heap leaching processing facility since 1983. Wharf Resources intends to mine and process gold and silver ore from the Wharf Expansion area which is located on the eastern flank of the currently permitted Foley Ridge Mine. The Trojan Pit for the Wharf Expansion area was initially designed with an overall highwall slope angle of 45o. During mine permit presubmission meetings with personnel from the SD Department of Environment and Natural Resources (SD DENR), the question arose as to whether a detailed slope stability analysis of the proposed Trojan Pit highwalls was completed to justify the 45o slope. Wharf’s response was that the highwall design was based, in part, upon studies completed in1987 on the Annie Creek and Foley Ridge Mines; and, in part, upon subsequent slope stability analyses conducted by Wharf mine personnel through 1996. It was suggested by the SD DENR that the stability study be updated to reflect structural geological conditions in the Wharf Expansion area.

Jan 1, 2000

By B. A. Ridolfi, S. M. Alvarez

The Moon Creek Reclamation Project provides a case study in the development of creative cleanup solutions for an abandoned lead and zinc mine and mill site located in northern Idaho. Innovative design features include construction of a 88,000cubic yard combined waste containment facility on soft in-situ tailings, water-balance cap, limestone gravel drains, a geocell mattress for stability, and a below-grade scour protection berm. The stream, including a wetlands buffer, will be relocated within an existing road alignment and rehabilitated to provide trout habitat. These elements allow for the integration of reclamation and stabilization measures into an effective site design.

Jan 1, 1999

By S. Rupprecht

"This article addresses the prevalence of poor public reporting practices of coal exploration results, coal resources and coal reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or saleable tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal — therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (ROM) and saleable coal tonnage, their associated qualities and other material and relevant information.Competent or qualified persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provided. “Companies are encouraged to provide information in their public reports, which is as comprehensive as possible (CRIRSCO, 2013).” However, too often this isn’t the case, and material matters are either not reported or inadequately disclosed.According to the South African National Standard (SANS) 10320:2014 draft document, “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the saleable coal reserve must be stated. The moisture basis of reporting shall be stated.” An example as to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are detailed in the followint paragraphs. The Kendal power station, commissioned in 1988, operates at a calorific value (CV) range of 19 to 20 MJ/ kg, an ash content between 29 and 34 percent and volatiles between 20 to 21 percent. Other power stations, such as Kriel or Hendrina, may require different qualities, such as a CV range of 22 to 23 MJ/kg, an ash content between 20 and 28 percent and volatiles between 22 to 23 percent. Thus, in terms of domestic saleable coal, it is not just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station (Chetty, 2010).” Sulfur content is another important quality with the ideal coal content having a quality of less than 1 percent sulfur."

Jul 1, 2019

By O. Konovalov, M. Zhuravkov

In report the results of performance of research works on building up of the connected geoecological and geomechanical monitoring system for modelling and study of a state of mining massif in a region with large-scale underground mining works are discussed. The connected geoecological monitoring requires radical change of methodology of carried out works. To carry out modelling and researches it is impossible without construction of the integrated connected information model of region. Basis of construction of information systems and databases for all sections of Earth Sciences is the set of the approaches, among which, for example, methods of remote sounding, GIS- and GPS-technology etc. Computer technologies are basis on the "supercomputer" technology. The results of performance of some researches for regions of excavation of deposits of potash salts in Russia and Belarus are presented.

Jan 1, 2005

By M. K. Larson, R. G. Wade

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time-dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct-shear tests on mud-stoneovercored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

Jan 1, 2000

By F. -J. Wodopia

Sustainability of energy supplies has been an issue of general interest for a long time. Whilst in the past the continuous productive use of natural commodities was in the fore, its compatibility with the environment and climate and ultimately also social aspects have recently gained more and more attention. Today many discussions focus on the climate compatibility of individual options to act. Fossil fuels, in particular coal and lignite, are generally challenged because coal use makes a significant contribution to global man-made CO2 emissions. The drastic increase in the consumption of fossil fuels is not explained by the fact that coal utilisation technologies are not or cannot be sustainable but rather by the growing world population and the endeavours numerous national economies trying to catch up economically. Coal is the world’s No. 1 fuel and, in the view of many experts, will keep this position also in the foreseeable future. The access to its deposits plays a significant role for the economies of the emerging countries. Consequently the aspects of energy security and economic efficiency need to be considered at eye level with climate compatibility. In Germany, however, the public acceptance of fossil fuels and of large industrial projects is in the focus of attention.

Jan 1, 2011