Search Documents

By Vijenac Quarry, A. Iljazagic, t. Knezicek, T. Omeragic

Limestone quarry Vijenac, is one of the key limestone producers in B&H. Conventional massive drilling and blasting is the technique applied for limestone exploitation. Utilized blasting scheme causes appearance of large oversize stone pieces, uncontrolled flying stone and undesirable seismic effects. In order to reduce or eliminate exposed disadvantages and to improve environment in the area of Vijenac quarry, an innovative blasting scheme was tested. Conventional blasting scheme was changed from single row, deep inclined blast holes combined with two lines short horizontal holes to multi row, inclined blast holes combined with a single line short horizontal blastholes. Applied innovative blasting scheme reduces negative blasting impact on the environment through safer working conditions, reduced amount of dust after blasting, reduced explosive and energy consumption, reduced appearance of explosive gasses and reduced earth and air vibrations as the result of seismic effects.

Jan 1, 2005

By P. Rusin

Many oxide silver and molybdenum deposits remain undeveloped because chemical extraction yields poor recoveries or is environ-mentally unacceptable. Bio-reductive leaching of such ore samples at MBX resulted in high recoveries of silver and molybdenum. When baseline 3-day cyanide bottle roll tests were conducted on manganiferous oxide silver ore, 13.7% of the silver was extracted. In contrast, 86% of the silver was microbially solubilized into the organic growth medium by bio-reduction with 99.8% dissolution of manganese. A follow-up cyanide bottle roll test yielded an additional 8.5% silver recovery for a total recovery of 94.5%. Baseline 3-day acid bottle roll tests of the iron oxide molybdenum ore yielded 1.8% moly. However, bio-reduction solubilized 93.3% of the moly into the growth medium. An additional 0.3% moly was recovered during the follow-up acid bottle roll test. Microbial treatment of refractory oxide ores with bio-reductive bacteria resulted in higher recoveries of silver and molybdenum than conventional chemical leaching. The bioleaching process occurred at a near-neutral pH at ambient temperatures. The bacterial solubilization of silver and moly was achieved without the use of cyanide or sulfuric acid.

Jan 1, 1992

By L. P. James, W. W. Atkinson

Utah has produced about 31.7 kt (1 billion oz) of silver, more than any state in the United States except Idaho. Several high-grade ore systems in Utah, where the mines are now closed, occur within large polymetallic limestone-hosted districts related to plutonic complexes. These mines fed several major lead smelters for nearly a century. Interaction of magmatic chloride-rich fluids with carbonate rocks localized significant bonanzas within these districts. A low sulfidation state was produced in the fluids by their passage through limestones. The Bingham openpit mine has also yielded more byproduct silver than other porphyry copper-molybdenum-gold systems. Away from exposed intrusive rocks, some large silver-only systems occur in Mesozoic sandstone and in caldera-related veins in volcaniclastic rocks. Thick permeable latest-Proterozoic basement metaquartzite sequences present beneath western Utah may have been important, as perhaps they were in the Coeur d'Alene district of Idaho, in providing chloride and silver-rich ore fluids. However, it is clear that specific Tertiary magmatic events played an essential role in the evolution of the Utah silver-rich metallogenic province. The largest silver districts in the state are genetically related to Tertiary porphyritic plutonic rocks.

Jan 1, 2003

By Daniel J. Dobbels, Eric R. Drooff, James R. Wheeler

Construction of Boston’s C11A1 Section of the Central Artery (I-93)/Tunnel(I-90) Project beneath the existing MBTA Red Line Subway at South Station required excavation to depths in excess of 33.5 m (110 ft) through permeable sand and gravel subject to almost 27.4 m (90 ft) of hydrostatic groundwater pressure. As tacked drift tunnel underpinning system was designed to provide positive support to the active station prior to mainline tunnel construction. As part of this system, a permeation grouting program was developed to facilitate tunnel excavation. This paper describes the design and implementation of the grouting program, in sit testing, and the overall performance of the grouted soil mass.

Jan 1, 1999

By P. M. Soupios

An integrated suite of environmental methods was used to characterize the hydrogeological, geological and tectonic regimes of the study area, to determine the geometry of the landfill (depth and spatial extent of electrically conductive anomalies), to define the anisotropy caused by bedrock fabric fractures and to locate potential zones of electrically conductive contamination. The study area which covers an area of about 0.08 Km2 is a municipal solid waste site (MSW), located 20Km West of Herakleion in the central part of Crete (S. Greece). The landfill is located in a northwest oriented valley with highlands to the northeast and southwest. The combination of geophysical methods and chemical analysis are commonly implemented for characterization and management of land-fills. At the particular site, geophysical methods were focused on studying the electrical insolating properties of the materials, electrical con-ducting properties of fluids (leachates) and electromagnetic properties of the disturbed regolith materials in the burial zones. Three different types of geophysical surveys were performed: 1) 2D electrical tomography (ERT), 2) electro-magnetic measurements using very low frequencies (VLF) and 3) electromagnetic conductivity (EM31). Furthermore, in order to calibrate the geophysical methods dielectric spectrometry measurements are conducted. To evaluate the environmental degradation of the area, soil and liquids samples were collected.

Jan 1, 2005

Introduction The frigid regions of Canada's high arctic islands are well-known for major oil and gas explorations. But mining leads the way in development. Cominco Ltd.'s Polaris mine is in its second full year of commercial production, and outstripping the rated production capacity foreseen by its planners. The Polaris mine is located on the shore of Little Cornwallis Island, near the settlement of Resolute Bay. The mine property is compact. It occupies about 3 km2 (0.5 sq miles) of the vast Arctic landscape. A number of mining and technological firsts were necessary to bring a mine into production at this 76° North latitude. Development constraints that had to be overcome included climate, remote location, and the limited ice-free shipping season. Construction of the entire process plant and ancillary facilities took place on a barge in the South where labor and supplies are plentiful. The plant was towed through ice-strewn waters to its permanent location at the mine site 1450 km (900 miles) from the North Pole. Freighters moved the first shipments to the South during ice break-up in late summer 1982. Most of the zinc concentrate is sold to European smelters. The remainder is tolled at a custom smelter in Europe, and the resulting metal is sold by Cominco. Lead concentrate is sold to European smelters. The mine was designed to produce 177 kt/a (195,000 stpy) of zinc concentrate and 41 kt/a (45,000 stpy) of lead concentrate. Actual production in 1983 was considerably greater, with both mill throughput and feed grades being higher than forecast. Production was 217 kt (239,300 st) of zinc concentrate and 51 kt (56,300 st) of lead concentrate. Average milling rate was 2.3 kt/d (2500 stpd), well above the designed capacity of 2.1 kt/d of (2300 stpd). Arctic Climate Extremes The climate is typical of the Arctic: very dry with short, cool summers and long, cold winters. From November through February, there is continuous darkness. Continuous daylight prevails from April to August. Precipitation is light, rivaling the Sahara desert at about 127 mm (5 in.) of rain and snow a year. An almost continual wind forms deep snow drifts against any obstacle on the ground. Temperatures range from a winter low of about -50°C (-58°F) to a relatively pleasant 15°C (59°F) during sunny days in August. Freeze-up begins in September and ice thickness increases from less than 0.3 m (1 ft) in early October to a maximum of about 2.1 m (7 ft) in May. The permanently frozen ground extends to a depth of about 427 m (1400 ft). Only a few inches of surface ground thaws in the summer. Exploration Activity Zinc-lead mineralization was

Jan 10, 1984

By R. L. Guerguerian

Hydrostatic trunnion bearings were recently provided on large Semi-Autogenous Grinding (SAG) mills driven by wraparound motors assembled on the head to shell flanges. A conventional SAG mill would have a ring gear driven through one or two pinions. The effects of the magnetic air gap forces from this new SAG mill drive arrangement on the performance of the bearing are discussed. A step-by-step systematic analytical de-sign of the hydrostatic trunnion bearing is presented, followed by a discussion of grinding mill erection requirements to conform with the design. A brief comparison with other bearing types and their response to the effects of magnetic air gap forces are also presented.

Jan 1, 1992

This paper examines the feasibility of combining network modeling and computational fluid dynamics for modeling of underground mine ventilation systems. Both simulation methods have specific advantages and disadvantages for analysis of mine systems. Network modeling is widely utilized by many operations and allows for assessment of current systems and simulation for planning purposes. Alternatively, CFD has been utilized only marginally by operations and is typically a research tool, requiring considerable computational power, complex models, and careful analysis and calibration of results. Network modeling allows for a holistic approach to the ventilation system, giving quantity, velocity and pressure in every branch, but CFD modeling can resolve the flow regime in 2-D or 3-D, which is idea when examination of an area on a more detailed basis is useful, such as dust and gas control. Integration of the two can allow for more flexible systems analysis. The feasibility of integration, along with application to limited underground mine data are examined.

Feb 23, 2014

By J. G. Groppo

In 1992, 48 million tons of fly ash (not including bottom ash, boiler slag and FGD material) was produced in the United States, according to the American Coal Ash Association. Of this amount, 27.2% was utilized; although the percentage of fly ash utilized increased from 20% in 1980, there is significant potential to increase utilization. One of the primary driving forces behind increased utilization is increased disposal costs due to more stringent environmental controls and regulation. Fly ash is classified as a natural pozzolan and finds significant use as a cement additive. It has been found to increase the plasticity of the cement mixture while lowering the amount of mix water needed. In addition to improving leveling and finishing properties, fly ash improves pumpability as well as decreases the heat of hydration of the concrete mix which is particularly important in massive concrete structures such as dams where the concrete needs to cool as quickly as possible. The Loss on Ignition (LOI) of fly ash is an important quality when considering utilization. The LOI is primarily due to the presence of unburned carbon and the standard specifications for the use of fly ash as a mineral admixture in Portland cement concrete are given in ASTM C618-89a. which sets an LOI limit of 6%. However, many states have set a more stringent limit of 3%. The primary reason for the lower LOI specification is that carbon adsorbs air entraining agents which limits freeze-thaw resistance. This is particularly important in climates such as the midwestern US where multiple cycles of freezing and thawing are typical in winter.

Jan 1, 1995

By I. Sanchez

The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites. The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites.

Feb 23, 2014

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

Manufacturers have improved various stirred mill types to be well adapted to fine and ultrafine grinding applications. These stirred mills, which are operated in wet or dry conditions, may be classified as horizontal — such as AHM-horizontal agitated media mill, IsaMill and Drais mill — or vertical — such as tower mill, Vertimill, Maxmill, Stirred Media Detritor and ATR vertical agitated media mill. The main difference between vertical and horizontal structures is in their operational variations. Additionally, the scaling-up of mills is also an important parameter for selecting the suitable orientation [1]. The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch-type stirred mill. The experimental results were evaluated using stress intensity analysis. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1 × 10−3 to 5 × 10−3 Nm at 750 and 1,500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value.

By RALPH BALTES, AMIR EHSAN KIANFAR, FABIAN UTH, ELISABETH CLAUSEN

  Underground positioning and communication are essential technologies for the future of underground mining operations. In contrast to other positioning and communication technologies such as wireless local area network (WLAN) or radio frequency identification (RFID), ultra-wideband (UWB) radio technology provides significant benefits like accurate and robust positioning of mobile machine equipment, which is indispensable for future autonomous systems in underground mining processes, such as production, transportation and auxiliary operations. Among these technologies, UWB offers many advantages, including higher accuracy, robustness, resistance against noise and multipath effects, and low power consumption [1,2]. Underground automation and localization systems benefit from these advantages and use the technology to improve efficiency and safety. There are many studies being carried out on this technology to increase the results’ accuracy, energy sufficiency and more. Two robust UWB modules that were developed for underground positioning and collision avoidance with regard to human safety in underground mining operations are introduced. The measurement results of tests carried out in an underground mine are discussed as well to confirm the functionality of the system.

By L. K. Holder

The White King / Lucky Lass Superfund site consists of two former uranium mines in south-central Oregon. The remedy included consolidating two large mining overburden stockpiles that contained low levels of radioactivity and heavy metals by moving over 700,000 cubic yards of material and then capping the combined stockpile. An innovative armored cap design was used to minimize the stockpile footprint and thereby prevent disturbing existing wetlands. In addition, the stockpile was designed to merge into the surrounding topography. The remedy also included stream restoration and development of new wetlands. The stream was returned to its pre-mining channel, with the addition of hydraulic features to create new wetlands. The wetlands have greatly enhanced the ecological value of the remedy and the site.

Feb 23, 2014

By W. A. McKinney

The U.S. Bureau of Mines, Kennecott Copper Corp., and New Mexico Institute of Mining and Technology are cooperating on a research project to improve extraction of copper from previously leached waste dumps that are in part compacted and impervious to leach solutions. The field work is being done at the "J" leach dump, Chino Mines Division, Kennecott Copper Corp., Santa Rita, N. Mex. The laboratory percolation leaching tests were made at the U.S. Bureau of Mines Salt Lake City Metallurgy Research Center on drill core samples from the "J" dump to determine how much copper might be leached if permeability could be restored by explosive heaving or other means. The core samples from nine drill holes on "J" dump contained from 0.06 to 0.14 percent copper. Copper extractions ranging from 15 to 3 percent were obtained in 75 days by percolation leaching of minus-1-inch material with dilute sulfuric acid. The tests results indicate that about 2'7 percent of the copper remaining in the "J" dump could be extracted under ideal leaching conditions.

Jan 1, 1970

By Thomas M. Lynberg

WIDCO is a surface coal mine located near Centralia, Washington. The WIDCO preparation plant processes over 7 million tons of run- of-mine coal each year with a product yield averaging 72%. In the jig type preparation plant the fine refuse amounts to approximately 130 dry tons per hour of 28mesh by 0. This fine refuse material is thickened in a 160ft. diameter static thickener with the use of lime as a coagulant and organic polymer as a flocculant. Once thickened the fine refuse, which is predominately bentonitic clays, has been dewatered and disposed of using several different methods. These methods will be discussed and include vacuum disc filters, ponds, solid bowl centrifuges, belt filter presses and experiments with electrokinetic dewatering.

Jan 1, 1981

By D. A. Robbins

The application of remote sensing for environmental measurements is already being utilized. Aircraft mounted imaging spectroscopy has been utilized to evaluate areas of historical mining operations as well as active mine sites. To the extent that remote sensing can provide more sensitive, cost effective, and timely monitoring potential, the technology is of interest to the industry. Questions remain about the application and validation of the data and the availability of the technology in the private sector. This presentation will discuss some of the potential uses, benefits, and concerns related to remote sensing and efforts to monitor the technology's development.

Jan 1, 1999

By K. Fleck

Energy West Mining Co. (EWMC) has implemented a geologic program for improving stability and support requirements along deep two-entry longwall gateroads at its Deer Creek Mine operations located near Huntington, UT. Together with geotechnical monitoring and concurrent review of mine seismicity in cooperation with MTI staff, it has become possible to improve longwall layout designs for two seam extraction of the Hiawatha and Blind Canyon seams. The geologic program consists of surface and in-mine exploration drilling, surface and in-mine geologic mapping, rock mechanics testing and detailed measurements of changes in depositional and structural conditions during development of every longwall gateroad. The geotechnical program consists of underground measurements at seven locations in two neighboring mining districts located in the Hiawatha and Blind Canyon coal seams under moderate to deep cover. Within the last five years, additional measurements, including data on seismicity and face conditions, have been incorporated into the data collection program for verifying the in situ coal strength and load transfer mechanisms for improving two-seam designs and support systems.

Jan 1, 2012

By S. C. Lamey, P. A. Hesbach

This study evaluated the use of regionally produced coal combustion products to neutralize and remove metals from acid mine drainage (AMD). Synthetic AMD mixtures were treated with a number of fly ashes and fluidized bed combustion (FBC) ashes. All of the ashes reduced the volume of the sludge produced and gave a faster settling rate than the sludge produced by treatment with lime. Faster settling allows greater throughput rates. In addition, the FBC ashes, which generally contain alkaline components used for sulfur capture, completely neutralized the acidity and, if desired, raised the pH above 10. The fly ashes, on the other hand, reduced the final volume of sludge but required additional neutralizing agents to attain a pH >5. The pH of the AMD can be taken to above 10 to insure complete removal of manganese, or it can be taken to a more neutral pH of 7 or 8 to allow for the safe introduction of the aqueous phase into ponds or streams. The process combines two industrial waste products to reduce the disposal volume of one of the waste products and to produce an environmentally safe aqueous discharge.

Jan 1, 2002

By J. Potter, A. Anani, C. Antonio

This research aims to test the hypothesis that the low retention rate of women in the mining industry is caused by workplace culture and policies established due to gender segregation. A quasi-experiment is developed to determine the cause-and-effect relationship between gender segregation-inspired culture and the retention of women. The experiment considers the impact of the job type and the operational environment. The analysis provides information on factors that cause low retention of women in the industry, the extent to which gender segregation plays a role, and insights that allow actionable and measurable changes in the industry.

Feb 1, 2023

By Adam Bedell, Paul Derby, Brad Crenshaw

Modified contact grouting was introduced almost 15 years ago as a methodology combining traditional contact grouting and consolidation grouting to address groundwater infiltration into hard rock tunnels that utilize cast-in-place concrete as permanent tunnel support. This process has been used on additional tunnels (since initially presented) as a measure to mitigate both groundwater infiltration and exfiltration. During this time, self-sealing grouts have been developed and have been added to the process to further reduce groundwater infiltration that occurs through cracks and discontinuities within the concrete liner itself. This modification is presented and additional results from the grouting process are discussed.

Jun 13, 2021