Search Documents

By Harry C. Verakis

A conveyor belt fire presents a serious safety hazard in an underground coal mine. A review of underground coal mine fires involving conveyor belts which occurred within the past two decades was made by the Mine Safety and Health Administration (MSHA). Belt fires that occurred during this period of time have burned as much as 610 m of belting before the fire was extinguished. In an effort to improve safety, MSHA has undertaken a program to study the flammability of conveyor belts in large and small-scale tests. Large-scale tests were conducted on various types of mine conveyor belts using a range of airflows from 0 to 6.1 m/s. Data were obtained to evaluate the effect of airflow on flame spread and other combustion properties of the conveyor belts. The results from the large-scale tests were utilized to develop a new MSHA laboratory-scale test for evaluating the flame resistance of conveyor belts used in underground coal mines. Agreement of results based on a pass/fail criterion was obtained between the large-scale test and new laboratory-scale test. A summary of test results from the new test is shown for different conveyor belt formulations. MSHA also performed a series of fire tests with wood samples using the new laboratory-scale tunnel apparatus. These tests were conducted at airflows from 0.5 to 5.1 m/s to determine the effect on flame spread and burn damage. The data were also analyzed to determine if wood could be used as a calibration standard. The results indicate the flame spread behavior of the wood follows trends similar to results obtained with conveyor belts. The data did not show the precision needed to use wood as a calibration standard. MSHA intends through rulemaking procedures to replace the "20g" conveyor belt acceptance test with the new laboratory-scale test. MSHA also plans to implement a voluntary acceptance program. Under this program, a. conveyor belt manufacturer could obtain an MSHA acceptance for belts meeting the new test criterion. A belt accepted under the voluntary program could then be used underground. Use of conveyor belts meeting the new test would limit the propagation of fire and reduce the probability of igniting other combustibles in the belt entry.

Jan 1, 1991

By E. R. Spencer

National Institute for Occupational Safety and Health (NIOSH) researchers conducted an investigation to quantify sound levels and to determine the amount of sound reduction provided by engineering noise controls installed in a talc processing plant. Baseline sound level and sound intensity measurements were performed at the plant and the measurement locations were recorded for comparison to post-control measurements. Follow-up measurements were then made at the same locations after the initial noise controls were installed. The plant subsequently decided to implement additional noise controls and the researchers returned to conduct measurements for a final analysis of all noise controls. The most significant results showed a sound level reduction in the main mill area from a range of 93-104 dB(A) down to 90-94 dB(A), and a total sound power level reduction of 21 dB(A) for air classifying mill 3.

Jan 1, 2008

By D. J. Kunz

Myanmar Ivanhoe Copper Company Ltd. (MICCL) has been operating the Sabetaung- Kyisintaung (S&K) Project producing LME Grade A Copper Cathode using the Heap Leach-SX-EW Process since 1998. The mineralization is mainly Chalcocite and the mine has a life of 20 years at the designed annual production of 25,000 tonnes of cathode copper. Design capacity was achieved within two of months of start-up. The mine is among the world’s lowest cost, Heap Leach-SX-EW operations. Information regarding plant design and operation are presented along with the challenges lying ahead and the latest developments. Daniel Kunz is President and Chief Operating Officer of Ivanhoe Mines, and a director of MICCL. He has more than 20 years’ experience in mining, construction and engineering. Prior to joining Ivanhoe Mines in 1996, Mr. Kunz was Vice President and Controller of Morrison Knudsen Corporation, a major international mining and construction company. He was also President and Chief Executive Officer of MK Gold Company, a public mining company listed on NASDAQ.

Jan 1, 2001

The 18th annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held on Saturday, Dec. 2, 2000 at The Westin La Paloma in Tucson, AZ. The 2000 inductee, guest of honor and featured speaker at the banquet will be Ronald C. Cambre, chairman and chief executive officer of Newmont Mining. He will be honored for his role in positioning Newmont as an innovative and key player in the gold mining industry.

Jan 1, 2000

By N. Aouad

Dump truck operators are exposed to whole-body vibration (WBV) levels that exceed the International Standard Organization (ISO) 2631-1. The WBV level measured by RMS acceleration value, for operator comfort, and long-term health and safety is under 0.315 m/s2 by these standards. However, fundamental research by Frimpong and Aouad (2009, 2012) and field experimental study by Kumar (1999) have shown that operators are exposed to extreme WBV levels exposing them to injuries and musculoskeletal diseases in the long-term. These extreme WBV values in the vertical direction are equal to 3.56 m/s2, 1.12 m/s2 and 0.87 m/s2 for the operator?s seat, lower-back and cervical regions, respectively. This paper will outline current research to solve these problems. Keywords: WBV, Truck Vibrations, MSC.ADAMS, Virtual Prototyping

Feb 27, 2013

By R. T. Langland

The U.S. Bureau of Mines has conducted underground tests and computer analyses to study coal mine roof behavior. Southern Ohio Coal Company provided test sites it) their Heigs mines located near Athens, Ohio. Testing apparatus was adapted for monitoring roof behavior at the face of mining from a remote surface location. Finite element analyses were applied to study the structural conditions present. Test sites were located at three different intersections of entries and crosscuts of the room-and-pillar mine. Electrical read-out instruments were used to record roof bolt loads, roof sag, and roof-floor convergence. They were installed during the roof bolting cycle of a conventional mining section and data was recorded for several months. Normal mining operations continued throughout the test period with minimal interruptions due to the installation and monitoring of the instruments. A computerized data acquisition system, partly underground, partly on surface, permitted continuous monitoring of data and its retrieval, display, manipulation, and storage. The finite element code used to model the test sites accounted for three-dimensional geometry, nonlinear material behavior, and the mining excavation and bolt installation sequences. Results of the test are highly variable. Comparable values between test and analysis results were obtained by applying statistical averaging of. roof test data. Results of the analyses indicate that bolts have a lesser effect on the gross behavior of mine roofs than has been indicated and that bolt load changes are strongly influenced by mining excavation sequence, bolt-placement sequence, and face distance

Jan 1, 1977

By K. Awuah-Offei

An aggregate plant may have difficulty balancing product stockpile inventories if hot mix asphalt (HMA) design engineers do not account for aggregate inventory during mix design. Yet HMA design engineers do not, often, take this into consideration during asphalt mix design. This is due to the lack of tools that enable the lab technician or engineer to optimize the mix for good performance while helping the aggregate plant manage its stockpile inventory levels and reducing the aggregate cost. This work presents a linear programming model of the asphalt mix design problem that helps aggregate plants manage their inventory levels while meeting HMA customer demands. The algorithm is implemented in MATLAB as an Asphalt Mix Design Optimization (AMIDO) program. The program is successfully validated with real-life data. The results show that AMIDO can be used to successfully produce any mix design while reducing the cost of aggregates by using the cheapest stockpile materials. The application of AMIDO will increase aggregate plant profitability when serving HMA customers and could potentially be modified for concrete aggregate customers too.

Jan 1, 2009

Membrane technology has been available for over 36 years, but has been used sparingly in the general mining industry. However, recent developments in polymer chemistry, spiral wound element construction, pretreatment equipment and techniques and an expanded understanding of membrane fouling and cleaning techniques have dramatically improved the reliability and robustness of membrane based systems in the mining industry. Harrison Western has expanded the use of this “new” technology to enhance the use of membrane technologies to separate metals from large volume heap leach mining solutions containing copper, zinc, and iron, gold or silver. Moreover, membrane technologies are ideally suited to fractionations that add value to processing fluids from refineries like separating metals from acids or concentrating acids and producing high quality process fluids. Finally, wastewater from Acid Mine Drainage (AMD) or, as in the case of the Newmont Yanacocha Mine in Peru, the treatment of excess barren leach solution created during the rainy season, can be cost effectively processed to meet World Bank Standards for surface discharge. Polymeric membranes, specifically thin-film composites, have been developed that will purify, fractionate or concentrate gold, silver, copper, zinc or nickel. Recent applications have been developed for spiral wound modules that operate across the pH spectrum from 0 to 14. Systems using membranes have been constructed that operate on feed streams from 140° C to 300 centipoise. Opportunities exist to apply membrane technology to concentrate gold, silver, copper, zinc or nickel using thin film composite membranes. Engineered membrane types can operate across the spectrum from low pH (<2) acid applications to high pH > 10 cyanide applications. Incorporating HW EMS™ membrane technologies into current mining operations could allow one to increase production because the membrane technology would be used to pre-concentrate heap leach solutions, and therefore, increase utilization of existing extraction and refinery capabilities.

Jan 1, 2007

By K. L. Lownie

For research and test data to serve a useful purpose, it is essential that it be derived from some known standard test procedure that allows for comparative analysis as well as independent replication and verification. Fan performance data provided by manufacturers is not absolute, and is influenced by the geometry of the test installation. For these reasons, fan test standards have been prepared in order to establish a clearly defined test procedure that allows for comparison of different fan designs, and also allows for the independent verification of test data. Internationally recognized Standards such as BS848, ISO5801, and AMCA 210 etc. are highly prescriptive, and precisely specify test duct configurations, measurement procedures, measurement planes and instrumentation to be used. Provided the laboratory tests are conducted strictly in accordance with the relevant Standard, the performance data will accurately reflect fan performance within the appropriate tolerances for efficiency, pressure and flow when tested in the defined configuration. Major differences in performance exist between a fan tested in accordance with a Fan Test Standard, and an identical fan installed in a mine ventilation system. The aerodynamic performance of any fan will be influenced by the quality of the fan manufacture, the flow system within which it is operating, the location of measurement planes, and the system stability. The flow distributions present in a standardized Laboratory test are unlikely to be repeated in mine ventilation systems, and this will also disadvantage fan performance. Unless the fan supplier takes all of these influences into account, there will an inevitable reduction in fan aerodynamic performance, and the end user will experience a shortfall in expected flow through the mine. The effect on fan performance can range from minor inconvenience to catastrophic fan failure resulting in major rectification costs and significant loss of mine production.

Jan 1, 2009

By F. S. Kendorski

Several startup or longtime underground stone mines have experienced unanticipated roof control difficulties due to the variable geologic character of the roof strata. Careful mapping of roof conditions, and identification of controlling geologic and mine geometric factors, lead to an understanding of the mechanisms causing roof problems. Factors such as unexpected rolls of the roof strata resulting in a gradual change from strong to weak roof; encountering open water-filled master joints; roof strata delamination due to internal water pressures; local karst features with mud, sand, and water hazards; and sudden loss of limestone roof due to paleo-channel erosion are some recent problems described. Strategies for overcoming these problems are discussed and detailed.

Jan 1, 2002

By P. C. Thakur

Frictional ignitions (also called face ignitions) is defined as the rapid oxidation of a mixture of methane and air with a visible flame that could last from a few seconds to several minutes. These ignitions have a potential to turn into a mine explosion and eventually a large-scale mine fire. Over the last 22 years, U.S. coalmines have had 1566 frictional ignitions. There were no fatalities but serious injuries have occurred. Every effort, therefore, should be made to prevent frictional ignitions. The preventative measures fall under four categories: (a) degasification of coal seams prior to mining, (b) adequate ventilation, (c) wet cutting or water-jet assisted cutting and (d) machine design to minimize ignitions. The paper discusses each of these techniques in detail.

Jan 1, 2006

By A. Cole, F. Porretta

Barrick Gold recently implemented an oxygen roasting process to treat carbonaceous ore from its Goldstrike property in Nevada. One of the key project challenges was the design of the roaster gas cleaning system, which was driven by the requirements of a strict air permit and the need to achieve very high reliability. The roaster gas systems include multiple stages of wet particulate collection, a dual alkali SO2 scrubber, mercury scrubbing, CO oxidation and NOx reduction. This paper describes the gas system, the influence of regulations on project implementation, and performance of the system.

Jan 1, 2002

By M. Botz

Anatolia Minerals Development Limited (AMDL) is constructing the Çöpler Gold Project in eastern Turkey and commenced mining in the fourth quarter of 2009 with gold production scheduled to begin in the fourth quarter of 2010. The project is a 15,500 tonnes/day oxide heap leach with three-stage crushing, agglomeration, carbon adsorption and electrowinning for final metal recovery. Leach solution copper levels are expected to be relatively low during the first two years of production but will increase in later years due to higher copper content in the mined and processed ore. Over the mine life approximately 40 million tones of ore will be placed on the leach pad, which will contain about 35,000 tonnes of copper. Metallurgical testing indicates copper extraction will vary by ore type and, if controls are not implemented, may lead to copper levels exceeding 1,000 mg/L in pregnant solution. High copper levels in leach solution have the deleterious effect of increasing cyanide consumption and potentially overwhelming the ability of the carbon circuit to effectively adsorb the principal economic metals, which in this case are gold and silver. Using data obtained from laboratory leach column testwork, the heap leach facility was modeled using METSIM process simulation software to estimate the build-up of copper in leach solution over the mine life. Laboratory testwork was also performed to evaluate process conditions for treating a portion of pregnant leach solution via sulfide addition to precipitate saleable copper as copper sulfide (Cu2S).

Jan 1, 2011

By A. Tobey Yu, W. Joseph Schlitt, Alfred Weiss, Frederic L. Kadey, Louis Kuchinic

Introduction The February and April 1984 issues of MINING ENGINEERING have already provided introduction to the long-range planning efforts of the Society of Mining Engineers (SME). These efforts are intended to provide the basis for effectively maintaining and improving the Society in the face of the changes that are besetting the mineral industry. This requires that SME recognize what changes are occurring and determine how these will impact the membership. Then a plan must be developed and implemented so that the Society successfully meets the challenges of the next decade. The Board of Directors has charged the Long Range Planning Commission with the responsibility for meeting these goals. This article provides a summary of the work done by the Management and Organization Committee of the Long-Range Planning Commission. This committee&apos;s task was to analyze the Society&apos;s current organizational structure and management process. Then a set of recommended improvements was to be developed. In doing this, the Committee has been careful to operate under that popular axiom, "If it ain&apos;t broke, don&apos;t fix it." Thus, changes were not proposed simply for the sake of change, but only where the present system appeared to be less effective than desired. Bases For Action The Committee began by establishing a set of premises about SME and its membership. These premises provided the bases for subsequent actions and recommendations by the Committee. Highlights from the premises included: • The Society should be run on a business-like basis. However, its "business" is that of a not-for-profit scientific, technical, and educational public institution. SME enables professionals involved in or associated with the mineral industry to serve the public purpose of benefitting mankind. • The Society operates as a national (US) organization with transnational (worldwide) interests. It recognizes its obligation to make its goods and services available to minerals professionals throughout the world. In addition, the Society recognizes its obligation to translate technology for the "lay" public, who then also become users of its goods and services. • The Society&apos;s Board of Directors is the policy-making body of SME and has final approval of all programs. These responsibilities will become greater when the Society becomes a separate corporation. • At present, the Society provides the following goods and services: publications, meetings/programming/short courses, academic education support, information dissemination - internal and external, and individual member services. • Planning is an ongoing process. It is best performed on a decentralized basis. That is, each major service category should have a responsible group authorized to conduct planning for that category, subject to the Society&apos;s master plan and the Board&apos;s approval. • The Society is privileged to have highly qualified and motivated members who volunteer their time and efforts on behalf of the Society. The best of these volunteers should rise to the highest positions of leadership - the Presidency of the Society and Institute (AIME). • The Sooiety is strongly committed to the protection and promotion of the history, traditions, and identity of AIME and the use of AIME as the unifying forum for the Constituent Societies. Identification of Potential Problems Once the premises about the Society and its membership were well in hand, the committee began examining the many facets of SME&apos;s organizational structure and management process. This was done in order to identify problems or potential problems in these areas. After considerable review and discussion, 10 areas of potential concern were called out for more detailed study and possible recommendations for improvement. These 10 areas include: • A lack of continuity at the Board level and among officers due to the established turnover policy. • A series of subboards that serve, by practice, to diffuse management authority and accountability, rather than enhance it. • A question as to whether the dissemination of information has been adequately planned, organized, and staffed. • An apparent illogical divisional organization. Two divisions are discipline oriented and two are commodity oriented. • A regional organization that does not adequately fulfill its purposes. • Uncertainties about the per-

Jan 6, 1984

By T. J. Nelson

Natural aggregates, primarily stone, sand and gravel, are recovered from widespread, naturally occurring mineral deposits and processed for use primarily in the construction industry. They are mined, crushed, sorted by size, and sold loose or in concrete products to build roads, houses, buildings and other structures. Smaller quantities are used in agriculture, cement manufacture, and chemical and metallurgical processes. The growth of cities, their buildings and the highways that connect them have created demand for enormous quantities of aggregates. Consumption has now reached 9 t (10 st) per person and continues to grow faster than population. The aggregates industry is the largest mining industry in the United States in terms of production by weight, by volume and by number of active operations. About 80 percent of the concrete pavement and more than 90 percent of the asphalt pavement is composed of aggregates.

Jan 1, 2006

By E. M. Spokes

Starting in 1980, a committee of the National Research Council studied the question of why some underground coal mines are safer than others and what could be done to improve the ones with poorer performance. The results indicated that safety is improved by management commitment to safety, by cooperation between labor and management on safety matters, and by quality training of employees and managers. Younger miners have higher accident frequencies, but are less likely to be killed or permanently disabled by a lost-time accident. Methods for improving safety performance are proposed.

Jan 1, 1987

By Fernando Humberto Muge

One of the problems that arises in the early stages of the mine planning before the determination of the mining exploitation method is to predict what will be the recoverable ore reserves in tonnage, grade and metal quantity, if the select ion is based upon block grades. The estimation of these recuperation or recoverable functions can act as an important planning tool in what concerns the appraisal of the consequences of ore-waste discrimination of individual blocks in a selective mining operation. Estimation methods of all these functions are discussed together with cross validation tests using the available information concerning a preliminary drilling campaign accomplished during the exploration stage of an iron orebody located in the North of Portugal (Moncorvo Orebody).

Jan 1, 1982

By Z. Konstantinovic, M. Ahrens

Due to the large installed electrical power and the large number of electric drives in minerals and mining plants power factor compensation and harmonic filtering has always been an important issue. For the design of harmonic filter and power factor compensation installations several approaches can be taken. The paper describes different concepts and their advantages and analyzes special requirements and design considerations for minerals and mining plants. It also highlights areas where problems can occur and which points need to be addressed carefully. Optimized designs and solutions are discussed in case studies and the resulting energy savings and benefits for the plant operation are shown.

Jan 1, 2007

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sinktimes were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1%, and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying, and dumping of coal products by comparison to airborne dust capture from sprays.

Feb 27, 2013

In practice, frothers are selected following general guidenlies and verification by laboratory and/or plant flotation tests. The terms “powerful” or “selective,” which are commonly used to characetrize frothers, have intuitive rather than scientific meaning. A research program has been set out to study fundamental properties of the flotation frothers and to identify the tests which can provide information needed to characterize and classify such flotation agents.

Jan 1, 2004