Search Documents

By Rodrigo Jerez

Advances in inexpensive computer automation led to the development and use of a computerized ore control system at the Cyprus Copperstone Gold Mine near Parker, AZ. These new ore control practices improved accuracy, performance and productivity of the ore control effort. An automated system for data collection, including bar coding of blasthole samples, laboratory analysis, data management, grade estimation, cut delineation and ore zone stake out, plays a major role in ore control practices. This is of particular interest because of the large amount of blasthole information being processed, analyzed and reported daily. Copperstone Gold management has been progressive toward new, efficient methods regarding ore reserve estimation, long-term mine planning, short-term mine planning, ore control and surveying. Technological advances, including powerful personal computers, applicable mine planning software and surveying instrumentation, have become readily available and affordable. The computerized ore control procedures used at Copperstone include sample data collection, laboratory automation and computerized data management. These have reduced the time to complete ore control on a blast pattern by 50% to 75%. The final product - ore control - is generated in a more timely and accurate manner.

Jan 1, 1991

By Ravi Ray, Kostas Kaklis, Zach Agioutantis

"Modern underground mining is becoming more complex and geotechnically challenging. The engineer uses numerical, analytical, and data-driven methods (empirical and/or experimental) or their combination to overcome these challenges. Each method has its advantages and disadvantages. Nevertheless, given the amount of innovation and experience involved in developing each of these techniques, it will be prudent to use all their benefits rather than favoring one technique over the other. Pillars are the most important support element in an underground mine. A holistic geo-mechanical solution needs to be determined to design mine pillars using a proper sequence and exact mix of the three methods. A combination of these methods, in sync, can encompass the several advantages of the three methods while eliminating their disadvantages. This paper presents a conceptual three-tier solution to the pillar design problem, to improve its design pedigree, using a proper combination of numerical, analytical, and data-driven methods. At the focus of this proposed method lies the Ground Reaction Curve (GRC) concept.INTRODUCTIONAlthough the stability analysis of underground excavations is a challenging problem, its understanding has improved tremendously over recent years through the use of improved tools and techniques. The trial and error method was replaced with more scientific methods like the empirical and analytical methods that are still in use today. Empirical methods were developed based on large data sets obtained from experiments and observations (e.g., coal pillar strength equations). Analytical methods were developed based on mechanical understanding of stability (e.g., safety factor for vertical pillar loading, Convergence Confinement Method). Improvement in computing power and numerical techniques led to the development of several numerical methods (e.g., finite difference, finite element) suitable for geo-mechanical analysis.Each of these methods have certain advantages and limitations. Nevertheless, the user is often puzzled over the proper method selection and over the proper sequence of using them. This exercise becomes more challenging when different methods are combined, where, for example, one has to estimate the pillar strength based on empirical equations (e.g., Mark-Bieniawski coal pillar strength equation), determine the factor of safety based on an analytical approach (e.g., tributary area load divided by pillar strength), and analyze pillar-strata interactions using numerical analysis (see Esterhuizen, Mark, and Murphy, 2010b).Challenges increase when current pillar design methods are designed as passive structures to balance the fixed dead weight of the overburden. This classic suspension design approach does not recognize the self-stabilizing capacity of the overburden (Frith and Reed, 2018). A practical solution to address these issues is the use of numerical analysis. However, one should always keep in mind that the numerical modelling approach may have certain practical limitations."

Jan 1, 2019

By J. D. Miller, C. L. Lin

As the techniques and resolution for 3-D spatial analysis have advanced in the last decade, it is now possible to map in detail the microstructure of multiphase materials in three-dimensional digital space. In this regard, three-dimensional x-ray microtomography offers a unique imaging capability. Spatial resolution on the order of ten microns can be achieved with the use of microfocus x-ray generators. Recently, a state-of-the-art cone beam x-ray microtomography system has been installed at the University of Utah for the quantitative analysis of multiphase materials in three dimensions. This facility has been designed to obtain 2048 x 2048 pixel reconstruction over a 10-mm diameter, while also allowing for the imaging of somewhat larger (40-mm) objects. The system is capable of handling high-density materials, even materials having a density as high as 8.0 g/cm3. This unique, one-of-a-kind, instrument will be used to obtain three-dimensional spatial reconstruction for such applications as specific examples 3D liberation analysis, pore structure analysis of particle beds during filtration and air-void system of concrete structures. The utilization of x-ray microtomography not only will allow for quantitative analysis of multiphase systems but also allow for textural characterization and the determination of phase continuity. In this paper, we present information regarding the current use of this new facility and reviewed potential applications for the advanced analytical system.

Jan 1, 2001

By L. K. Marshall

Last month's engineering fundamentals article discussed some general considerations of underground mine ventilation. This month's article takes a look at auxiliary ventilation-brattice, fans, and ducting-in underground mines. The need for good, efficient auxiliary ventilation increases as mines get deeper and move farther from ventilation shafts. New mining methods and equipment resulted in faster work area advances, liberating more dust, gas, and heat. As a result, worker health and safety requirements in the face area have become more stringent. For all these reasons the safety and efficiency of any underground mine depends heavily on its auxiliary ventilation. The purpose of such ventilation is to supply sufficient quantities of clean air to the face of the drift and to maintain air quality within desired limits until expelled from the mine.

Jan 2, 1982

By K. R. Gardner, P. B. Altringer, R. H. Lien, B. E. Dinsdale

The Bureau of Mines, U.S. Department of the Interior, is investigating chemical and biological decontamination of complex wastewaters such as tailings pond water containing 280 ppm CN and 5 ppm Se as well as significant concentrations of arsenic, copper, iron, silver, and zinc. The most effective chemical procedure involves cyanide oxidation using hydrogen peroxide or sodium hypochlorite followed by selenium reduction using ferrous hydroxide. The effluent contains ?1 ppm CN and 20 ppb Se; concentrations of other - major contaminants meet National Drinking Water Standards. Preliminary research indicates that biological cyanide oxidation is possible even in highly alkaline solutions (pH 10.5) containing high cyanide concentrations; indigenous bacteria destroyed 85% of the cyanide. Exploratory research shows that other bacteria removed up to 79% of the selenium from chemically oxidized, low- cyanide water. These promising results may lead to a final processing scheme that involves a combination of chemical and biological techniques.

Jan 1, 1990

The administration came on as a strong supporter of the mining industry in April of 1982 when President Reagan delivered his long-awaited minerals policy statement. He promised to reduce America's minerals vulnerability, and called for spending billions on meeting stockpile goals for strategic minerals, opening up federal lands for mineral exploration, elimination of barriers to deep sea mining, and regulatory relief. He defended the favorable tax incentives in the Economic Recovery Act as a stimulus to private research and development that would ensure the availability of materials essential to the nation's economy and national defense. But the administration just didn't seem to get anywhere. Congress, environmentalists, and even foreign governments fought White House-proposed legislation on all fronts, delivering the ultimate coup in forcing Environmental Protection Agency Administrator Anne Burford's resignation and the subsequent EPA staff house cleaning in early 1983. Anti-Reaganites scored victory after victory against Reagan's efforts to stimulate the minerals industry. Congress was stalemated on so many mining-related issues that not much was done either for or against the industry. And the US was not to get its way on the issue of sea mining either. Most of Reagan's mineral policy objectives failed to be met. Three months after the National Materials and Minerals Program Plan was presented and the Cabinet Council on Natural Resources and the Environment was made its coordinator, the head of the Cabinet Council James Watt blamed lack of progress in reviving the mining industry and creating a better strategic stockpile on the weak economy and the House of Representatives, which repeatedly thwarted efforts to open wilderness lands to mining. Congress The 97th Congress spent much of its time saying no in 1982-to the Reagan administration's deep cuts in energy and environment programs, to major changes in clean air and water laws, to oil and gas leasing in wilderness, and to killing the Department of Energy. Most of 1982 (and 1981) was spent in heated budget disputes. Some things that did not happen: • The administration and industry failed to get changes in controls of hazardous air pollutants and sulfur dioxide emissions that are implicated in the phenomenon known as acid rain. Industry had wanted to relax requirements for new industries building in clean air regions where the air act demands prevention of significant deterioration (PSD) of air quality, and to relax requirements tightening up the regulation of emissions of hazardous air pollutants. The air battle is expected to continue on five major fronts-acid rain, hazardous air pollutants, PSD, automobile pollution, and nonattainment. • Regulatory reform legislation to overhaul the way government carries out the law died a slow death last year. Business groups and the administration said federal agencies should be required to consider cost-effective measures of reaching regulatory objectives of protecting public health, safety, and the environment. Opponents, including environmentalists, feared such action would delay, weaken, or scuttle important regulations. • Congress turned thumbs down several times on proposals for oil and gas leasing in wilderness but could not agree on any new wilderness recommendations (see The Wilderness Battle). • Congress refused to open the door to the Reagan administration's plan to raise up to $4 billion a year from sales of federal lands. The administration identified surplus and excess federal lands, mostly obsolete buildings or isolated tracts of land, that could be sold by the General Services Administration (GSA) to help out the federal budget deficit. Congress took no action. Some things that did happen: • Congress extended the Defense Production Act (DPA) for six months through March 1983 without changing the 32-year-old law. That came after it failed to resolve sharp differences over proposals for critical minerals programs. Differences concerned both the amount of funds and the scope of programs that would be authorized under the DPA's Title III. Some proponents pressed for $5 billion in funding for loan guarantees or purchase commitments to spur domestic production of minerals such as cobalt. Other members of Congress wanted smaller amounts of funding, and the Reagan administration, until about November, had opposed any use of federal funds for strategic mineral programs. These measures were certain to come up again before the DPA extension expired in March. • House supporters of the Critical Materials Act of 1982 were unable to come up with the twothirds majority needed to pass the bill, so it died on the House floor in December. The bill proposed that a council be established with responsibility for coordinating federal materials research and development. The administration opposed the council creation contending that the Cabinet Council

Jan 5, 1983

This paper was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bumps in the prevention of fatalities and accidents in highly stressed, bump-prone ground conditions. Changes of failure mechanism with increasing confinement, from extensional- to shear-dominated failure, are widely observed in the rupture of intact specimens at the laboratory scale and in rock masses. In the previous analysis conducted in 2018, both unconfined and triaxial compressive tests were conducted to investigate the strength characteristics of some specimens of a Utah coal, including the spalling limits, the ratio of apparent unconfined compressive strength (AUCS) to unconfined compressive strength (UCS), the damage characteristics, and the post-yield dilatancy. These mechanical characteristics were found to be strongly anisotropic as a function of the orientation of the cleats relative to the loading direction.

Jan 7, 2020

By B. Boberg

Annual requirements of uranium to fuel the 441 currently operating nuclear reactors in the world is 170 million pounds U3O8 (65,385 tonnes U). 2005 global production was 108 million pounds (41,595 t U), of which only 2.7 million pounds U3O8 (1,039 t U), was produced from US uranium deposits. US nuclear utilities represent 26% of the global nuclear capacity but only obtain 2.5% of their supply from US uranium mines. Since 2002 annual global production increased from 93 million pounds U3O8, a 15% increase and the US production increased from 2.3 million pounds to 2.7 million pounds, a 17% increase. Reasonably Assured Resources (RAR) of 12,332 million pounds U3O8 (4.7 million t U) are reported from a wide variety of countries and types of uranium deposits. This RAR suggests that there are significant global uranium resources potentially producible at a price of $50 per pound U3O8 ($130 per kg U). Table 1 shows the distribution of global uranium resources. This table, prepared from historic data maintained by the World Nuclear Association, does not include some areas of the world that are currently considered to contain significant resources of uranium such as Mongolia. Table 1 suggests that the United States contains the fourth largest uranium resource in the world with 890 million pounds U3O8, behind Australia, Kazakhstan and Canada in resources that are producible at a price of $50 per pound U3O8 ($130 per kg U). Within the US, the states that demonstrate the greatest amount of uranium resource are Wyoming, New Mexico, Texas and the Four Corners Area of Arizona, Colorado and Utah.

Jan 1, 2007

By Kira Mizell, James R. Hein, Tracy Conrad

"The Ninetyeast Ridge (NER) extends roughly N-S as a topographic feature for 5000 km, from 31° south to 10° north (Fig. 1) where it becomes buried beneath the Bengal Fan at its northern end. These two geographic characteristics make the NER an ideal natural laboratory for determining the influence of latitude and terrestrial input to ferromanganese (Fe-Mn) crust formation and composition. In addition to study of geographic controls on crust composition, the NER is the largest feature in the Indian Ocean that may host crusts of economic interest.Crusts were collected from 9 of 33 dredge sites from 1.4° north to 26° south latitudes during the 2007 R.V. Roger Revelle Knox06 cruise. Nineteen samples were analyzed for 69 elements each. Nine bulk crusts and 10 layers from four crusts were analyzed. Three of the crusts sub-sampled for layers did not have the bulk crust analyzed and the weighted means for those layers were calculated to obtain bulk compositions. One sample was left out of the statistical analyses because it is phosphatized and chemically quite different from the other samples (Table 1).In order to determine changes in composition with latitude, Pearson product-moment correlation coefficients were calculated for the chemical dataset and latitude of dredge sites, as well as water depth. At the 95-99% confidence level, the following elements increase in crusts moving north along the NER: Mg, Ti, S, Cd, Ni, Tl, Mn, Ba, Co, Cu, In, Li, and Zn; and the following elements decrease northward: Fe, Fe/Mn, P, As, Sc, the rare earth elements plus yttrium (REY), Bi, Ge, and Pb. These correlations indicate that the iron oxyhydroxide component and its associated elements are more prevalent to the south, and the manganese-oxide phase and associated elements increase toward the north end of the NER. This change occurs between dredges D20 and D14 (Fig. 1), with crusts from D20 and south having Fe/Mn !1.0 and those north of D20 ""1.2, with the exception of the phosphatized crust. Crust composition also changes with water depth: Th, Ge, Pb, and the middle rare earth elements (REEs) increase with increasing water depth. Thorium commonly increases in deeper water crusts, which explains the higher Th concentrations in Atlantic and Indian ocean crusts in general compared with Pacific crusts (Fig. 2 and Hein et al., 2012), including the samples analyzed here with a mean water depth of 3584 m. However, water depth does not explain the latitudinal changes because the mean water depths of samples along the northern and southern segments of the NER are roughly comparable. Surprisingly, Si and Al, representing the aluminosilicate/detrital phase, do not correlate with latitude; that is as the ridge approaches and is buried by the Bengal Fan the Si and Al contents do not increase. However, overall, Si and Al have higher concentrations in NER crusts than in central Pacific crusts. Ba can be used as a proxy for primary productivity and statistically does increase to the north along the ridge in the direction of the equatorial zone of high biological productivity. Correlations of Mg, Li, and Zn with latitude may also reflect increased primary productivity at lower latitudes."

Sep 1, 2014

By W. Hustrulid

In the mid-to-late 1800’s the U.S. mining industry was on the threshold of nearly a century of golden times. Nearly every state had a prosperous and growing mining sector. The importance of the industry was reflected in the creation of the state school of mines. Today, with the depletion of readily available mineral reserves, much of the U.S. metals mining industry is considered to be in a sunset phase. The same is true with the mining schools that serve the industry. However, the United States is still a major consumer of the world’s minerals and requires a dependable supply of both minerals and minerals professionals. In his 2002 Jackling Lecture “You Can’t Make a Silk Purse Out of a Sow’s Ear” the author presented a list of concerns, propositions and recommendations. In this follow-up paper, the author further explores the subject through the presentation of a detailed case example focusing on the iron mining industry of Minnesota and minerals education at the University of Minnesota.

Jan 1, 2004

By D. C. Dahlin, W. K. O’Connor, G. E. Rush, C. A. Summers, S. J. Gerdemann

The Albany Research Center (ARC) conducted studies of mechanical activation by conventional and ultra-fine grinding techniques to enhance olivine reactivity in mineral carbonation reactions. Activated olivine is one of several solid feed materials used at ARC in reactions with carbon dioxide to form carbonate minerals. This paper compares grinding techniques via energy demand data and product characteristics, including particle size distributions, surface areas, full width at half maximum (FWHM) XRD analyses, and particle morphology by SEM analyses. Reactivity was gauged by percent conversion to carbonate in subsequent carbonation tests.

Jan 1, 2004

By Donald W. Foss

The Shiloh Church deposit is a very significant molybdenum occurrence in an ususual, perhaps unique, geologic environment. Work done to date indicate that several million tons of "ore" may be present, occurring as a matrix in limestone and dolomite breccias. Mineralized rocks cored to date are at or near the surface and the deeper resource potential has not been tested. The prospect is located in Polk County, north- western Georgia (Fig. 1). The "ore zone" was outlined by North American Exploration, Inc. (NAE) using geochemical prospecting techniques. Extensive geological work, including core drilling, has been conducted on the properties, together with geochemical and geophysical surveys. The geology, geochemistry and geophysics of the prospect are discussed. It is hoped that these data can be used to formulate exploration programs in similar terranes located elsewhere in the eastern U.S.A.

Jan 1, 1983

By Arif Emre Dursun, Ali Aras, Hakan Özşen

Specific energy (SE) is defined as the amount of work required to cut a unit volume of rock and is used to estimate the performance of excavation machines. Generally, the SE value is produced from full-scale or small-scale rock cutting tests. However, these tests require expensive equipment and experienced personnel, and the testing procedure is time consuming and impractical. Therefore, for estimation of SE, this study aimed to find a solution to estimate SE using rock mechanics test results and Bond work index values (BWi), which can be produced in a more practical, less time-consuming manner and with inexpensive test equipment. Small-scale rock cutting, rock mechanics and Bond work index tests were carried out on seven rock samples, which can be grouped into two different type of rocks: marble and travertine. In addition, the instantaneous cutting rates (ICR) of a selected roadheader were calculated using SE values. Rock mechanics tests performed in this study were uniaxial compressive strength (UCS), Brazilian tensile strength (BTS), ultrasonic velocity (Vp), Schmidt rebound hardness (RL), corrected point load index (Is(50)) and density (ρ). The simple regression method was used to estimate SE from rock properties and BWi. As a result of this simple regression, a significant and highest correlation was found between SE vs. UCS and Is(50). A good correlation was found between SE vs. BTS, RL and BWi values. A moderate correlation was found between SE vs. Vp and ρ.

Jul 28, 2021

By D. R. Spears

As part of its mission to develop technology to assure a continuing supply of minerals, the US Bureau of Mines has investigated the flocculation of a Stillwater, MT, chromite ore. The ore was flocculated at different solids contents and at different stirring speeds to determine the importance and effect of hydrodynamic factors. In acidic and basic pH, the chromite ore was flocculated with high molecular weight polyacrylamides differing in the degree of hydrolysis. Polyacrylamides were found to bind to chromite ore particles through hydrogen bonding. The anionicity of the polymer and the pH affected the degree of polymer-particle interaction, which in turn affected polymer conformation at the surface. A polymer conformation with many loops and tails was used to explain high flocculation efficiency. It was found that such a conformation could compensate for poor hydrodynamic conditions.

Jan 1, 1992

By J. -G. Swanson

Dust control in longwall coal mining depends primarily on the prevention of dust at the source and secondarily on the suppression of airborne dust. One of the primary methods for the prevention of dust is the wetting of the coal face prior to extraction, which can be achieved with water spray systems installed on the shield supports. The spray droplets must travel across the airway to the longwall face, where high ventilation air speeds can entrain water droplets and prevent them from reaching the face thus minimizing the dust control at the source. Through an evaluation of spray plume characteristics in a wind tunnel, the droplet size and droplet drift behavior was determined. This drift behavior was examined by evaluating the spray plume concentration drop and the droplet size shift near the nozzle exit at varying air speeds. Based on these evaluations, CFD modeling was applied to simulate the spray behavior for varying geometries. These results led to the selection of appropriate spray nozzles capable of carrying water droplets to the face at higher air speeds, resulting in an adequate wetting of the coal face and reduced dust generation.

Jan 1, 2012

By Priscilla P. Nelson

Many concepts concerning equipment selection, performance prediction, and evaluation of support requirements for tunnel construction in soil or hard rock tunnels cannot be extrapolated directly for application in soft rock (compressive strength between 1.0 and 35.0 MPa). Case histories for small diameter (less than 3.5 m) tunnels in Austin, Texas, are analyzed to gain insight into particular problems encountered during tunnel excavation in weak sedimentary rock, and the performance of different excavation systems are compared.

Jan 1, 1987

By Georgene Renner, William R. Yernberg, Steve Kral

Allmand exhibited its LSC 100Light Sequence Commander, the mining industry’s first automatic lighting and command control system. The system is available with all of Allmand’s portable light towers. The LSC100 uses a preset photocell sensor that allows the light tower to be automatically turned on or off. At dusk, the sensor engages the power unit and then activates the light. At dawn, the sensor automatically shuts off the light. The unit also features an eight-event digital timer that allows eight separate sequences daily. The LSC100’s sequenced light control ensures that the engine is started before the lights are turned on or off. This prevents possible generator damage that can occur if the unit is powered down under load. Also, a low-fuel shutdown sequence helps protect the generator from damage by automatically shutting down the unit when the fuel level reaches 10 percent. And the LSC100’s smart circuitry senses engine water temperature during startup, determines the glow-plug time requirement and schedules repeat intervals, if necessary, to start the diesel engine.

Jan 1, 2004

A glance at the accompanying table reveals that for the first time in many years the industrial minerals field did not post significant gains in production. Gypsum, cement, sand and gravel, and crushed stone production-which are very sensitive to construction industry performance-barely managed to stay even, or in fact, declined slightly. Even barite production, in spite of increased oil and gas drilling, was off 5% in 1979 from 1978. Domestic fluorspar production continued to decline while imports, primarily from Mexico, South Africa, and Spain, rose 11%. Worldwide production of iodine (which is used primarily as a catalyst, animal feed additive, and in ink and colorants, stabilizers, pharmaceuticals, photographic film, and disinfectants) grew about 9% on a worldwide basis-from 10.75 Tg to 11.16 Tg. This does not include US production. The two US producers increased demand as apparent domestic production increased about 5%. Increasing energy costs and the transportation situation have had a prohibitive effect on the industrial minerals field. The critical shortage of railroad cars, according to consultant Neil Johnson, is due to several factors: • High capital investment rind interest rates needed to build new equipment, • Accidents, obsolescence, and failure to repair equipment reduced car availability, •Reduction in some train schedules due to fuel economy, and •Increased turnaround time as a result of new safety regulations. Railroad rates have increased an average of 7% per year for the past 10 years. Last year's increases were about 11.1% due to fuel costs and surcharges. Truck shipments have increased their penetration in certain areas of the southeast because of the shortage of box cars and the producers' demand for quick shipment. Some producers report a 15-20% increase in truck use. In the feldspar-mica area, which formerly made most shipments by rail, trucks are now used for about half the shipments. Marketing prices, as expected, increased due to higher costs for energy, power, labor, and supplies used in production. Estimated average price increases were about 10% which, in many cases, did not cover increased production costs. These factors-rising energy costs and the critical transportation situation-resulted in an unsatisfactory year for industrial minerals. Stanley J. Lefond Cnntrihuting Editor

Jan 5, 1980

By Christopher J. Bise

INTRODUCTION The principal means for transporting men, supplies, and mined material in an underground or surface mine are rail systems, conveyor belt systems, or a combination of the two. Typically, large underground mines use rail haulage from the mining sections to the hoist, with conveyor belts being used within the sections. Small mines use conveyor belts in the mains and sub- mains as well as in the panels. The size and layout of surface mines also contribute to variations in the way these haulage systems are applied. The following sections address the typical problems confronting mining engineers in designing these haul- age systems. For rail, these include rail selection and turnout design, locomotive tractive-effort calculation, and motor sizing. Belt haulage calculations include belt width and speed specifications, tension and take- up requirements, idler spacings, and motor sizing. TRACK LAYOUTS Introduction The adequacy of mine track layouts is dependent upon such factors as rail weight (Table l), suitable ties, a well-drained roadbed, and properly designed curves, grades, and track alignment. As long as the installation conforms to the manufacturer's recommendations, good service can be expected from the rail system. Typically, mining-engineering calculations for rack layouts have dealt almost exclusively with the design of turnouts. As such, the following section provides the necessary information for computing the theoretically correct dimensions of turnouts. Turnout Design Fig. 1 shows a typical turnout with an identification of the component parts. Fig. 2 identifies the variables that are used to determine the turnout dimensions. The formulas that concern the mining engineer are those listed: [ ]

Jan 1, 1986

Introduction The Homestake Mining Co. has always been big on gold. After 108 years in the business, the company and its principal product are almost synonymous. The relationship continues. On Sept. 28, 1985, Homestake held formal dedication ceremonies for its newest gold mine - McLaughlin. The McLaughlin open-pit operation is located in northern California, some 113 km (70 miles) northeast of San Francisco. It lies near the boundaries of three counties - Napa, Yolo, and Lake - and a portion of its facilities are located in each. McLaughlin was originally the site of the Manhattan mercury mine that produced nearly 80,000 flasks of the quicksilver from the 1860s to 1978. At the September dedication, Homestake renamed the mine in honor of the late Donald H. McLaughlin. McLaughlin was with Homestake for nearly 60 years. He rose from exploration geologist to his ultimate positions of chief executive officer, director, chairman of the board of directors, chairman emeritus, and chairman of the executive committee. The discovery of the McLaughlin deposit occurred in 1978, the last year of operation for the Manhattan mine. Homestake geologists used a newly developed model and found surface gold at the mine site. That same year, Homestake signed an agreement with the property owner and began a two-and-a-half year exploration program. An initial discovery announcement of 31.1 t (1 million oz) of gold was made in 1980. In 1981, this was revised to 93.3 t (3 million oz), or 18 Mt (20 million st) of ore grading 5.2 g/t (0.152 oz per st). Expected mine life is 20 years. Construction began in September 1983, following the issuance of stage one permits. Start-up of operations took place in early 1985 and the first gold-silver dore bar was poured on March 4. Since then, more than 540 kt (600,000 st) of ore has been milled, producing about 1.6 t (50,000 oz) of gold. Of special interest at McLaughlin is the use of three autoclaves for gold extraction. According to Homestake, this is a first. The autoclaves are designed for a 90% gold recovery rate. Early results have proven yields at this rate and higher. Geology The McLaughlin deposit is about 1.5 km (5000 ft) long. It occurs as a wedge-shape, narrowing to a verti-

Jan 1, 1986