Search Documents

By Paul L. Russell

Interest in the western oil shales of the US began in about 1908, with the first retort in Colorado constructed in 1917. The most successful early developments were near Elko, NV, where the Catlin Shale Products Co. produced more than 1.9 dam3 (12 000 bbl) of shale oil during 1920-1924 and at Rulison, CO, where a US government operation produced about 570 in 3 (3 600 bbl) of shale oil during 1926-1929. Plentiful low-cost crude oil was developed about this time and shale oil was of little or no interest until after World War II. From 1944 to about 1972, several companies, and the US government, operated shale oil mines and recovery plants in Colorado. While technical successes were achieved and an estimated 40-56 clam' (250 000-350 000 bbl) of shale oil were produced, economics were not favorable and commercial production was not achieved. In recent years domestic production of crude oil supplies has not kept pace with US consumption. The growing shortfall has been met with imports. The cost of imported oil has continued to escalate and increased US dependence on petroleum imports are national concerns, because of the negative impact on US balance of payments and an increasing dependence on other nations for US energy needs. In 1978, petroleum imports equaled about 44% of demand, up from 23% in 1970, but down from 48% in 1977 because of availability of Alaskan North Slope crude oil. Reduced domestic consumption and other factors have reduced current imports to about 40-45% of de¬wand-but at ever increasing cost. The growing shortage of crude petroleum and its increasing cost have resulted in renewed worldwide interest in oil shales. In the past, the main obstacle to oil shale development (progress toward commercial production) has been economics-shale oil cost too much to develop and thus could not compete with conventional petroleum crudes. Even with today's inflated energy prices, some experts say the production of synthetic crude oil from oil shale is, at best, marginally economic. The 1973-74 Arab oil embargo and increased crude oil costs-along with the federal government's offer to lease oil shale lands-resulted in renewed

Jan 1, 1981

By P. H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior around underground excavations made in the mine. The aim of this study was to investigate the geotechnical behavior around a tunnel excavated in a metal mine in China at the three-dimensional level. Using the information available on lithology, geological structures, in-situ stress measurements, physical and mechanical properties of intact rock, discontinuities and interfaces between different rocks, a three-dimensional numerical model was built by using the 3DEC software to simulate a tunnel excavation under a high in-situ stress condition. Effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or continuum material and rock support system on the deformation, stress, failure zone and stability around the tunnel was investigated. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses.

Jan 1, 2012

By Luzheng Chen

Pulsating high-gradient magnetic separation (PHGMS) of fine hematite from tailings was studied using a pilot PHGMS separator to investigate the possibility of its application in industry. The results of this investigation indicate that PHGMS is effective for recovering fine hematite from the tailings and greatly improved the separation performance compared with the conventional high-gradient magnetic separation at the same conditions. By applying the pilot separator with a 1-mm rod matrix to a tailings containing 28.76% Fe, a concentrate assaying 54.35% Fe with 35.89% recovery was achieved. It was found that the separation performance of the pilot separator closely correlates with the main pulsating parameters, i.e., pulsating stroke and frequency. It was also found that a change in the wire diameter of the rod matrix from 2 to 1 mm causes a weak drop in concentrate grade but results in a considerable rise in recovery. This finding proves that the improved performance achieved by the pilot separator is attributed to the pulsating of slurry and to the use of a 1-mm rod matrix. When the first commercial SLon-2500 PHGMS separator with a 1-mm rod matrix was applied to recover fine hematite from the tailings, the results duplicated those achieved with the pilot PHGMS separator.

Jan 1, 2009

By F. Freme

Coal production in the United States increased in2004 by 36 Mt (39.7 million st) to end the year at 1 Gt(1.11 billion st), according to the U.S. Energy Information Administration (EIA). This was a 3.7-percent in-crease from 2003’s 971.6 Mt (1.07 billion st) (Table 1).(All percentage change calculations are done at the short-tons level.) Although U.S. coal consumption rose in 2004, not all coal-consuming sectors had increased consumption for the year. Coal consumption increased in the electric power sectors by 1 percent and declined slightly in the other industrial sector, while coking coal consumption dropped by 2.4 percent. U.S. coal exports rose for the second consecutive year, while coal imports again increased to record levels. Coal stocks declined during the year, as electric generators used their stockpiles to helpmeet increased demands and missed shipments. Coal producers used their stockpiles to supplement their production levels.

Jan 1, 2005

By Thomas A. Simpson

Traveling through the moors and valleys of Cornwall, England, one is reminded of the extensive mining activities of the past. Abandoned shafts, remains of granite block wheel houses and engine houses, battered brick stacks, old calciners, overgrown water wheel pits, count house remains, overgrown waste pits, and old portals are gaunt monuments to a once flourishing mining industry. Cornwall is bordered on the north by Devon and occupies the south-western most tip of Great Britain. The Atlantic Ocean borders the promontory; to the north, the mouth of the famous Bristol Channel faces the open sea; and to the south, the English Channel separates the land masses of Great Britain and Europe. This part of England is probably the most extensively mined ground in all of Europe. Such great mines as Dolcoath and Wheel Vor, Consols and South Carodan, Levant and Bottalack, remain legendary in the annals of metal mining in the nineteenth century. Many US mining districts hold close ties with Cornwall, Devon, and Wales through ancestors who emigrated from there to work in US mines in the eighteenth and early nineteenth centuries. Their descendants can be found in many major US mining districts, and their terms, expressions, customs, and methods have left an impact on the US mining scene that remains with us today.

Jan 9, 1981

By M. Z. A. Bakar

A series of full scale laboratory linear rock cutting tests was carried out with a long bladed single disc cutter (292 mm diameter, 11mm wide constant cross-section blade) on dry and water saturated sandstone blocks using a linear rock cutting machine (LRCM). The muck collected from the cutting tests has been analyzed to establish a link with the specific energy (SE) of the operation. Coarseness index (CI), a non dimensional parameter, has been found to be a useful indicator of the relative efficiency of the cutting operation. An inverse relationship of the form SE = k CI-n is observed between SE and CI with very high CI usually corresponding with the lowest values of SE. The power n of the relationship for both dry and saturated rock tests is much less than the values found in the previous studies using constant cross section disc cutters and is believed to be dependent on the strength of the rock and the cutter type used. Although the average CI is found to be lower for saturated rock than for dry rock, at the same time saturated rock cutting is found to be less energy intensive (in terms of SE) than dry rock cutting. Moderate correlation exists between the production rate or yield and the SE of the cutting operation for both dry and saturated rock, which can provide some useful information about the field production rate discounting the effect of discontinuities in the rock mass.

Jan 1, 2012

By Levent Ozdemir, Robert J. Evans, Russell J. Miller, William Sharp

This paper describes the specifications and capabilities of a 6 ft (1.83 m) diameter laboratory rotary cutting machine which was designed and fabricated under a Bureau of Mines (USBM) contract awarded to the Colorado School of Mines (CSM). The machine will be used for carrying out research and development programs aimed toward improving the design and operation of mechanical tunnel, raise and shaft boring equipment.

Jan 1, 1983

By Ian Martin

A precious metals refinery’s switch to personal computer-based, three-dimensional piping design saved many hours in the design of a South African precious metals refinery. Bateman Minerals and Industrial provided engineering, procurement and construction management services for Impala Platinum Limited-Refineries’ new $60 million refinery in Springs, South Africa. This project is one of the largest platinum refineries in the world. Bateman evaluated a new design method during this project that involved developing a three-dimensional model for the project. The new method saved time by reducing the man-hours required to generate complete project documentation, including plans, sections, isometrics and material takeoffs. The new method also saved design and construction time by allowing designers to detect clashes before construction began.

Jan 1, 2000

By W. James Marold

The New Croton Aqueduct (NCA) was the first major water supply tunnel for New York City. The 50-km (31-mi) long tunnel has 33 open shafts 6 m (20 ft) to 121 m (397 ft) deep. The tunnel and shafts are lined with brick and mortar, with cast iron lining and pressure covers in six pressurized shafts. Details of the 1895 construction are provided and compared to modern construction techniques. The paper provides rehabilitation techniques for the shafts and pressure covers, including grouting, epoxy lining, temporary bulkhead design and installation and placement of tremie concrete 98 m (320ft) below the water level in a 122 m (400ft)deep shaft using a Remote Operated Vehicle (ROV) to monitor the placement.

Jan 1, 2008

By T. M. “Mike” Gurr

"U. S. marketable phosphate rock production for the 2018 crop year (July 1, 2017 to June 30, 2018) showed an increase to 27.7 Mt (30.5 million st) from the 2017 crop year production of 27.1 Mt (29.8 million st), as reported to the U. S. Department of the Interior by the mining companies operating in the United States during crop year 2018 (Table 1). Domestic consumption decreased in the 2018 crop year to 23.9 Mt (26.3 million st), as compared to the 27.2 Mt (30 million st) consumed in crop year 2017. U.S. imports of phosphate rock increased to 3 Mt (3.3 million st) for the 2018 crop year from the 1.81 Mt (1.9 million st) for crop year 2017. Imports of phosphate rock were from Peru and Morocco. There was an increase of 2.85 Mt (3.1 million st) in producers’ stocks from 7.45 Mt (8.2 million st) in crop year 2017 to 10.3 Mt (11.3 million st) in crop year 2018 (Table I).For calendar year 2018, Florida and North Carolina phosphate rock production accounted for 75 percent of the total U.S. production, with the balance being produced in Idaho and Utah. The Florida and North Carolina percent of U.S. production is declining. U.S. production of 25.7 Mt (28.3 million st) in calendar year 2018 was produced by five companies at 10 mines in four states and accounted for approximately 9.6 percent of the world production of 267.7 Mt (295 million st) for calendar year 2018 (Table 2).In calendar year 2018, U.S. phosphate production decreased by 2.2 Mt (2.4 million st), while companies increased stocks of phosphate rock by 1.7 Mt (1.9 million st). The domestic production for calendar year 2018 of 25.7 Mt (28.3 million st) represents 78.4 percent of the domestic production capacity of 32.8 Mt (36.1 million st).At present, China reportedly produces more than 50 percent of the world’s phosphate rock. As a result of planned expansions, Morocco production has increased from 27 Mt (30 million st) in 2017 to 33 Mt/a (36 million stpy), which is approximately 12.3 percent of the world’s production, moving ahead of the U.S. production. In calendar year 2018, the U.S. phosphate rock production was 25.7 Mt (28.3 million st), which is less than 10 percent of the world’s production of phosphate rock (Fig. 1)."

Aug 1, 2019

By Dale Matthews

The Getchell Mine, near Winnemucca, NR, was discovered in the 1930s and was initially mined to recover gold from oxide ores. During the 1940s and 1950s, gold was recovered from the highly refractory arsenic sulfide ores using horizontal kilns to roast the ores. During the 1960s, fluid bed roasters were used to oxidize the ore and recover the gold. The mine was shut down from 1968 through 1985. In 1985, heap leaching was started on the low-grade oxide ores that were available. In 1989, a pressure oxidation circuit was started to recover gold from the higher grade sulfide ores. Flowsheet The basic plant flowsheet of the Getchell Mine are shown in Figs. 1 and 2. The plant was designed to process a nominal 2.7 kt/d (3000 stpd) of ore with about an 85% onstream availability and a gold production of 15.5 kg/d (500 oz/ day). Run-of-mine (ROM) ore is fed directly to a wet semiautogenuous grinding (SAG) mill after the +457-µm (+18in.) rock is removed on a stationary grizzly. From the SAG mill, the ore goes to a ball mill where it is ground to 80% -75 µm (-200 mesh) and is then sent to a thickener. The SAG and ball mill operate in closed circuit using cyclones.

Jan 1, 1994

By D. Pappas

Over the past decade the number of contractors working in underground coal mines has nearly doubled; however, the effect this has had on the industry?s injury rates has been the subject of much speculation. The confusion exists because the U.S. Mine Safety and Health Administration (MSHA) database does not assign contractor hours to the individual mining operations where they worked. To better understand the safety record of the contractor segment of the industry, the National Institute for Occupational Safety and Health (NIOSH) undertook a comprehensive analysis of the data contained in the MSHA database. The first part of the study compared overall contractor and operator trends from 1983 to 2009 related to employment, hours worked, injury rate, and days lost. One unexpected finding was that the larger contractors tended to have higher injury rates than the smaller ones. The second part of the study directly addressed the role of contractors on the safety record of 10 large underground coal mines. A detailed analysis provided both injuries and estimated contractor hours worked at these mines for the period 1992?2007. Comparison between the estimated contractor injury rates and the reported operator injury rates at these mines indicated that the contractor injury rates were significantly higher at most of the operations studied. However, the industry-wide data indicates that contractor and operator injury rates have converged since 2005 and are now equivalent.

Jan 1, 2011

By L. W. Saperstein

Public Law (PL) 95-87 contains explicit demands for land use planning in its reclamation and designation sections. Both sections require recognition of local land use plans; however, they are not well integrated. Accommodation to these planning requirements affords an opportunity to create better links among local land use planners, the state's permitting authority and designation office, and mine designers. Mining companies should take a more positive interest in local land use plans and in resource inventories. States should consider handing down to local government the responsibility for accepting mine permit applications and designation of unsuitability petitions.

Jan 12, 1983

By George K. Schenck

INTRODUCTION Recent advances in high-pressure water jet technology can be effectively employed in mining and tunneling. The new equipment is based on available industrial hardware such as pumps, nozzles, and rotary swivels and seals, and is compatible with present mining and tunneling techniques. Principal advantages of water-jet assisted cutting relative to standard cutting are higher production rates, lower dust levels, and reduced fines. When used on rock and coal miners, water jets mean that relatively smaller and cheaper machines can be purchased. If properly applied, the combined effect is lower cost and significantly improved health and safety. While commercial use of high-pressure water blast cutting and extraction of rock (and concrete) already has a firm foothold in Europe, application of this new technique is just beginning in America. This paper begins with current American applications of high-pressure water jets for drills, for slotting and channeling machines, and then discusses the emerging technology for initiating rock failure in conjunction with drag bits on coal plows, continuous miners and boom-type miners (roadheaders). The focus of this paper is use of high-pressure water jets for cutting rock. High-pressure water jet cutting utilizes water above 70 MPa and currently reaches to 300 MPa and above. Some informatfon is included on low pressure "wethead" coal shearers and boom miners with water pressure to about 15 MPa.

Jan 1, 1983

By J. Finch, R. McIvor

This paper presents the development of a new grinding circuit steady-state modeling system. It is fundamentally based on the “functional performance equation”, which has now been used to improve the performance of numerous grinding circuits. This equation characterizes the two distinct efficiencies that are at work in a ball milling circuit, and how these relate to overall circuit productivity. It does so based on the particle size chosen to distinguish between coarse and fine (product size) material. Now, by applying it to all the material size classes, a simple yet reliable ball mill model was created. Combined with cyclone recoveries, the complete, detailed grinding circuit performance can be exactly reproduced mathematically by the computer program. It can then be used with separate process equipment application engineering methods to systematically engineer grinding circuit improvements. The development, features, uses and limitations of the system are described.

Jan 1, 2007

China has made great progress in thick coal seam mining, commonly characterized by longwall top-coal caving mining and single-pass longwall mining with a large cutting height. At present, the maximum mining thickness of longwall top-coal caving reaches 20 m while that of single-pass longwall mining approaches 8.8 m. The top-coal caving–related technologies have significantly improved the mining efficiency of thick coal seams and have also made a great contribution to the centralized underground mining of coal. Thus, the number of underground coal mines is greatly reduced in China. However, due to the increase of the mining height and the changes in mining operations, the overburden movement caused by the mining of thick coal seams is more intense, and the influence scope is larger, which brings a series of new problems on ground control of longwall faces. In order to enhance ground control and improve the mining efficiency of thick coal seams

Jul 28, 2020

By J. J. Gusek

There are hundreds of passive treatment systems accepting mining influenced water (MIW) throughout the world. Some systems do not perform to design expectations while others, including volunteer systems, have successfully operated relatively unattended for decades. The primary reasons for this situation include the common misconceptions that (1) a “cookbook” approach to design is valid for a wide array of MIW chemistries and site conditions, and (2) low maintenance means “no maintenance.” Passive treatment systems for MIW are typically manmade ecosystems that are designed to handle a specific range of metal loading conditions and MIW geochemistry. Thus, when design conditions are exceeded, the suite of microbial to macroscopic ecosystems may be slow to recover or mature. This should be no surprise to designers. But when a particular system fails, it may be inappropriately attributed to the technology, not the design. This paper presents a standard “phased” design protocol that appears to work and provides examples of sub-par performance of selected passive treatment systems.

Jan 1, 2002

By R. W. Fedors, S. T. Green, G. R. Adams, C. Manepally, L. B. Browning

This paper provides estimates of large-scale temperature gradients that can be used to support modeling of natural convection and cold-trap processes in thermally perturbed drifts. Temperature influences estimates of the quantity and chemistry of water contacting engineered components (e.g., drip shields and waste packages) in a potential high-level waste repository at Yucca Mountain, Nevada. Temperature gradients drive natural convection and cold-trap processes, which could affect the distribution, quantity, and chemistry of liquid-phase water contacting drip shields (waste packages).The confluence of high temperatures, liquid-phase water, and high chloride may lead to corrosion of drip shields and waste packages. An overview of the evolution of environmental conditions in thermally perturbed drifts is presented to provide a context for the estimates of temperature gradients. A mountain-scale conduction-only model is used to estimate temperature gradients and temperature differences for a drift located at the center of a potential repository. Thermohydrologic models and heat transfer algorithms are used to evaluate the reasonableness of the conduction-only results. Estimates of temperature using an in-drift heat transfer algorithm account for the possibility of drift degradation and formation of a rubble pile on the drip shield. Temperature differences between the center and ends of the drift are estimated to rapidly increase to 80 °C soon after repository closure. That temperature difference decreases over time to 15 °C after 10,000 years. Local temperature gradients are generally estimated to be less than 0.2°C/m, though the gradients can be much larger near changes in lithology and near the end of the drift. The estimates of temperature gradients do not account for intermediate- and small-scale variations, such as those influenced by differences in heat loads between waste packages, intra-layer variations in thermal properties of the surrounding fractured rock, or localized drift degradation.

Jan 1, 2004

By M. Spangler

FirstMiss Gold installed a supervisory control system based on Pavilion Technology's Process Insights neural network software and Oil System's PI data historian. The primary goal of the system was to control the acid preconditioning circuit. However, our first successful control loop was on the limestone feed rate to the neutralization circuit. The information gained by modeling these circuits and the better control provided by the system has resulted in reagent savings of over $80,000 per month.

Jan 1, 1995

By Edwin F. Shorey, Richard F. Coon, Steven B. Fradkin

Crosstown Interceptor Phase IA is the first deep tunnel element of the Milwaukee Inline Project. The tunnel contract includes 6,492 meters (m) of 9.1-m-diameter tunnel, two access shafts, and partial lining for structural purposes. The work also includes grouting to be performed as directed by the engineer to provide groundwater infiltration control in lined and unlined reaches of the tunnel. This paper summarizes infiltration observations, progress of the grouting work, and its potential application to the remainder of the Milwaukee project.

Jan 1, 1987