Search Documents

There has been disappointingly little development in the analysis of rock slopes in open pit mines over the past 30 years. A brief review of literature shows that the application of numerical stress analysis methods to open pit mine slope stability has become only relatively common in recent times, and that there are as yet no standardized approaches. The lack of development in general, and of robust, standardized approaches in particular, is surprising in view of the ?ultra? deep open pit mines that are being developed to depths in excess of 1000 m. In this paper, the results of a substantial programme of two dimensional and axisymmetric analyses of open pit slopes are described. Variations in the following parameters were taken into account in this programme: slope angle, slope height and horizontal to vertical in situ stress ratio. The evaluation of the data has concentrated on the tensile stresses and the extension strains in the slopes. This is believed to be the first publication dealing with strain distributions in slopes. The occurrence of zones of tensile stress was very limited. These zones occur in the crests of slopes, except in the case of low horizontal to vertical stress ratios, in which case the tensile zone is in the floor of the pit. In contrast, very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. The large zone in which such extension failure could potentially occur in a 1200 m deep pit is typically more than 100 m horizontally behind the toe and about 400 m up the face from the toe. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning. Such ?strain bursting? produces easily measurable seismicity, events often being audible as well. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. With suitably orientated joints, extension strains are likely to manifest themselves in the opening up of such joints and hence in the loosening of the rock mass in a preferential orientation, with potential effects on groundwater flow patterns.

Jan 1, 2003

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk. Keywords platinum, mining, community, socio-economic impact, stakeholders, conflict, labour unrest, social licence to operate, investment, Africa.

Mar 1, 2013

By D. Tesh

The mining industry worldwide is facing a tremendous shortage of minerals engineers in all fields of specialization. For instance, in Australia the skills shortage in the mining industry has been identified as one of the top risks facing the mining industry. In Namibia most minerals engineers employed are expatriates, with some being Namibians who studied abroad. The minerals engineering programmes at the Polytechnic of Namibia are still in their infancy. These programmes were designed to meet the mining industry skills needs. Being young has its advantages in that lessons can be learnt from older minerals education institutions that went through similar challenges. However, this does not imply just copying and implementing their approaches, since the context differs and, to ensure sustainability of the minerals education programmes, curricula have to be customized to the local context. This paper reviews the interventions made by the Polytechnic of Namibia in order to ensure the sustainability of its minerals education programmes. The methodology consisted of an extensive literature review, a status quo analysis of the mining and process engineering department, identifying the gaps between the current state and desired state, and mapping the goals and strategic actions required to progress to the desired state. The following factors were identified as major threats to the sustainability of minerals education at the Polytechnic of Namibia: the quality of students, low student enrolment rates, low pass rates in science and mathematics, shortage of academic staff, dwindling government funding, and limited involvement of the mining industry. The major outcomes of this research comprise the detailed strategic actions employed by the Polytechnic of Namibia to address the threats to sustainability of its minerals education programmes.

Jan 1, 2014

By R. G. Cawthorn

The earliest authenticated scientific report of the occurrence of platinum in rocks from the Bushveld Complex appears to be by William Bettel on 10 November 1906. Thereafter, prospecting of the chromite-rich rocks for platinum proved frustrating. I suggest that the resurgence of interest shown by Dr Hans Merensky in 1924 resulted from his realization that newly panned platinum had a different grain size from that in the chromite layers and indicated a different source rock, which he located, and it became known as the Merensky Reef.

Jan 1, 2007

By S. K. Murphy, K. B. Le Bron, A. K. Ward, S. Hayes, T. Rangasamy

A process for evaluating different options for extraction of mining blocks is presented. The process is described and an example of the application of the process to a case study is presented. Un procédé pour évaluer différentes options pour l’extraction de blocs d’exploitation est présenté. Le procédé est décrit et un exemple de l’application du procédé à un cas particulier est présenté. Ein Prozeß für das Auswerten der unterschiedlichen Optionen für die Extraktion von Abbaublöcken wird dargestellt. Der Prozeß wird beschrieben und ein Beispiel der Anwendung des Prozesses zu einer Fallstudie wird dargestellt.

Jan 1, 2003

CSIRO Mineral has recently developed a new electron microprobe based system for characterizing zircon grains from heavy minerals sand deposits. The system acquires cathodoluminescence (CL) spectra, X-ray and backscattered electron (BSE) signals in parallel. By scanning over a specified target area, CL wavelength and X-ray element distribution maps of polished zircon grains can be acquired. Post-inspection of the combined dataset using in-house developed software enables correlations between chemistry and structure to be investigated. The new method offers significant benefits over traditional CL and BSE techniques in that direct comparison with the elemental concentrations over the same region is now achievable. By combining the electron microprobe results with data for the same mapped region obtained via a nuclear microprobe, significantly better detection limits (~ 1ppb) for elements with atomic numbers greater than iron are possible. The ability to measure spatially related analytical data and then investigate the correlation of the CL spectra with chemical data is an important advancement in the characterization of zircons. Key words: zircon, characterization, cathodoluminescence, backscattered electron, electron microprobe, nuclear microprobe, chimage, proton induced x-ray emission.

Jan 1, 2003

By W. Banda

Paper written on project work carried out in partial fulfilment of Phd. (Process Engineering) degree* The recovery of cobalt and copper from waste slag was studied in a plasma DC-arc furnace in reducing conditions. Three fluxes, CaO,CaF2, and TiO2, were investigated for their influence on selective recovery of cobalt into an iron-rich alloy. A further investigation on the influence of furnace power on the reduction of slag to recover cobalt to the alloy showed that a change in power setting had an unexpected effect on the recovery of metals to the alloy, in that selectivity of base metal recovery over iron recovery decreased at an increased power level. Keywords: DC-furnace, reduction, nonferrous, slags

Jan 1, 2004

By S. Escoffier, A. Giraud, K. Su, F. Homand, N. Hoteit

Abstract For the feasibility study of an underground waste disposal the characterization of the coupled behaviour of the host rock is required: Because of the very low permeability of these formations few experimental data are generally available. In this framework the uses of the sensitivity studies could orient the experimental efforts by highlighting the key parameters of the formation. This paper gives a first approach of the sensitivity studies performed with probabilistic methods in the geomechanical field. A one dimensional model which characterizes the thermohydromechanical response of an argillaceous rock to the excavation of a waste canister site and its setting up, is considered. Zusammenfassun Die Machbarkeitsstudie eines tiefliegenden Endlagers für radioaktive Abfälle beinhaltet die Untersuchung des gekoppelten Verhaltens des im Lagerbereich anstehenden Gesteins. Aufgrund der sehr geringen Wasserdurchlässigkeit dieser Formationen liegen häufig nur wenige experimentelle Angaben vor. Die Verwendung von Sensibilitätsstudien kann in diesem Zusammenhang als Hilfsmittel zur Entscheidungsfindung dienen. Dabei sollen die maßgeblichen Eigenschaften der Formation festgestellt werden, anhand derer der Umfang der experimentellen Erkundung festgelegt werden kann. Dieser Artikel stellt einen ersten Ansatz zur Durchführung von Sensibilitätsstudien mittels einer mechanisch-probablistischen Kopplung im Bereich der Geomechanik sowie die Vorteile gegenüber Parameterstudien vor. Zur Abbildung des thermohydromechanischen Stoffverhaltens von tonigem Fels während der Schachterstellung und der Einlagerung der Abfälle wird ein eindimensionales Model verwendet. Résumé L'étude de faisabilité d'un centre de stockage de déchets radioactifs en profondeur passe par la caractérisation du comportement couplé de la roche hôte. Du fait de la très faible perméabilité de ces formations, souvent peu de données expérimentales sont disponibles. Dans ce cadre l'utilisation d'études de sensibilité permettrait d'orienter les efforts expérimentaux en faisant ressortir les caractéristiques primordiales de la formation. Cet article présente une première approche de la réalisation d'études de sensibilités à l'aide de couplages mécano-fiabilistes dans le domaine de la géomécanique. Un model unidimensionnel caractérisant la réponse thermohydromécanique d'une roche argileuse au creusement d'un puit de stockage et à la mise en place de conteneurs de déchets est considéré.

Jan 1, 2003

By G. A. Craig

The Moon, asteroids, and planets of the solar system represent the most distant caches of wealth that humanity has ever considered recovering. Yet, in addition to the potentially recoverable values represented there, harvesting off-Earth resources has a second, almost incalculable sustainable benefit in that they can be retrieved with absolutely no damage to Earth. Previous research mostly assessed the potential of asteroids and the Moon for mining purposes from a theoretical and scientific point of view. These studies investigated drawbacks that could be experienced in this type of operation, but no detailed economic evaluation that is meaningful for mining project management has been conducted and the parameters that are most likely to make an operation feasible are unknown. This paper provides a preliminary economic and sensitivity analysis of a possible off-Earth mining business extracting minerals from an existing asteroid.

Jan 1, 2014

The practice of pumping gases which inhibit combustion for purposes of controlling or extinguishing mine fires is now universally accepted. The practice has been used many times in coal mines in India and the experiences are reviewed. The procedures relating to a membrane based nitrogen generator and to a combustion gases generator are described. The physical properties, practical requirements and economic implications of using different gases is briefly reviewed. Some aspects of the practice as related to mine fires in certain collieries in other countries are dealt with.

Jan 1, 2000

By A. J. Van Der Merwe, N. A. Barcza, M. Boyes, N. R. Clarke

Oriel Resources has with the support of SRK (Cardiff) and DRA and Mintek (South Africa) carried our a Definitive Feasibility Study (DFS) to recover high grade chrome ore from its Voskhod deposit very close to Chromtau that is near to Aktobe in Kazakhstan. Voskhod is a large podiform ore body that contains nearly 20million tons of chromite grading about 48% Cr2O3 and with a Cr/Fe ratio of over 3/1. Selected bore hole core samples were obtained from the confirmation drilling programme during the DFS phase of the project in 2005 for pilot plant test work to design the mineral beneficiation plant. The chrome ore is characterised by four main types, namely high grade lumpy and chip sized ore, high-grade fine ore, lower grade (subordinate) lumpy ore and lower grade fine ore. Gravity separation tests carried out by Mintek showed that the large density difference between the high grade (at over 3.7t/m3) and lower grade ore (at less than 2.97t/m3 ) should ensure very good separation in the DMS drum and DMS cyclone stages resulting in high recoveries of Cr2O3 - rich chromite ore products. Very high chrome ore grades of up to 64% Cr2O3 and Cr/Fe ratios of 4 to 1 were obtained at an 80% mass yield from selected samples of lumpy and chip ore size fractions. The overall predicted recovery from the design work on the mine and plant is expected to be closer to about 70% of the ROM (Run of Mine) feed. DRA has completed the design of the mineral processing plant to recover about 900 kt/a of chrome ore from the 1.3 Mt/a of ROM feed. The plant has been sized to handle up to 1.5 Mt/a and will also be able to address the variability in ore feed as different regions in the deposit are mined. The lumpy high-grade product and the chips size fraction is expected to grade around 48% Cr2O3 and the fine concentrate between 56 and 58%Cr2O3 The ratio of products is expected to be about 70, 15 and 15 percent respectively but will vary to some extent during the expected 20 year life of the mining operation based on including the associated adjacent Karaagash deposit together with the Voskhod deposit. The prediction of the product split from the processing plant depends on many factors such as the geology, mineralogy, mining, handling and metallurgical processing. An overall process flow model has been developed that covers the ROM ore, the various types of chrome ore feed to the mineral beneficiation plant, the projected products and the subsequent smelting of the chromite ores to produce High Carbon Ferrochromium. The model allows the optimisation of the quality of the chrome ore in terms of Cr2O3 content, Cr/Fe ratio and recovery to be studied. This information can also be evaluated in terms of the economic requirements for smelting High Carbon Ferrochromium (HCFeCr) at a given location. Oriel is planning to supply chrome ore to Ferrochrome plants mostly in China and Russia. The use of the model will assist to maximise the value of the Voskhod project to its owners and also assist the users of the chrome ore in selecting the appropriate supply quality to meet their needs for a given smelter operation. The smelting of high grade Voskhod ore requires a limited addition of about 5 to 7% quartz to flux the MgO and Al2O3 and about 25% coke as a reducing agent to produce an alloy containing from about 65 to 74%chromium depending on the Cr/Fe ratio.

Jan 1, 2007

By D. J. Greeff

By making use of genetic programming, empirical models for metallurgical processes can be evolved that are more cost-effective than models determined by means of classical statistical techniques. These methods explore populations of candidate models assembled from sets of variables, parameters and simple mathematical operators, and do not require explicit specification of model structures. The application of the proposed strategies is illustrated by means of a case study pertaining to the leaching of nickeliferous chromite ores. Modelling of the nickel and cobalt extraction from the ores yielded models of similar accuracy compared to those obtained by non-linear regression and artificial neural networks. However, in the case of the iron extraction from the ores, the genetic programming model was significantly more accurate than both the regression and neutral network models.

Jan 1, 1998

By C. Kasatuka

Globalization creates investment opportunities for enterprises around the world. Attracting foreign investment has been a key challenge for economic growth in developing countries. Corruption, political instability, armed conflict, and other internal problems affect foreign direct investment (FDI) inflows negatively. A framework of criteria provides a basis for comparing non-commercial risk (NCR) among twenty-three mineral economies. Countries competing for foreign direct investment inflows are ranked from least to most risky. This study compares Inward FDI Performance Index (IND) with NCR ratings in developing countries and shows that risk is increasingly mitigated by means of appropriately structured insurance. Given the option for countries with similar mineral potential, investors will generally invest in the country that offers lower non-commercial risk. Keywords: foreign direct investment, non-commercial risk, developing countries.

Jan 1, 2006

By T. Khumalo, L. P. Coetzer

This paper addresses the impact of the variable speed drive on the particle size distribution in the product of a fully autogenous UG2 grinding circuit. It further discusses the impact of a varying particle size distribution in the product of the mill on the downstream classification and milling circuits. An industrial case study was used and data is presented to illustrate the techniques applied to identify the root cause of the shift in operational efficiency. The results achieved from both the investigation into the shift in plant efficiency and the sub-sequent corrective action taken illustrate that the root-cause methodology used in advance control can be effectively applied on production sites to both detect the shift and identify probable root-causes. The industrial example used confirms that the variable speed drive in a UG2 autogenous milling operation is a critical control parameter to ensure that the plant operates to design specifications.

Jan 1, 2006

By T. Nishi, D. Teguri, K. Saitoh

In recent years the requirement for high carbon ferro-manganese (HCFeMn), which is the key product of our company, has increased due to bullish demand for steel products. In our Tokushima works, we have 2 closed types of electric furnaces (1F and 2F), with which we are manufacturing HCFeMn. In order to meet the increase in demand, we made various modifications to these furnaces and we tried to increase the furnace operating loads. Especially for 1F, we deepened the furnace. In this paper, we report the results of this modification. The operational situations of the above-mentioned two furnaces are different because they have different individual profiles. As for 1F prior to modification, the depth of the furnace was one meter shallower than2F, because 1F was designed for the manufacturing of SiMn. On the other hand, our Tokushima works specialized in HCFeMn 14 years ago. However, the profile of 1F was not optimized for HCFeMn. In comparison to 2F, 1F was more difficult to stabilize due to the smaller tolerance for the adjustment of the electrode length, the metal / slag level, and the coke-mixing ratio. We deepened 1F by 770mm by disposing of the furnace rolling mechanism. We consequently achieved a 10% increase in production capacity. This meant the operating load was enhanced from 24.5MW to 27MW, the furnace became more stable and the tapping speed of both metal and slag increased, all which made the tapping easier than before.

Jan 1, 2007

By J. Kerr

The first stage of the development of a new modified 201-type low nickel austenitic stainless steel is described in this paper. The alloy is intended for use as a structural alloy, and so requires a yield strength >400MPa as well as acceptable weldability and toughness. The low nickel content will give a lower material cost in comparison to more conventional austenitic grades, and the processing route is required to be similar to that of Type 304 to keep the processing cost low. The base alloy was designed using empirical methods developed for stainless steel, and the properties of the base alloy were verified using a range of small-scale melts. The base alloy had a 0.2% proof strength of ~320-400MPa, and so it is planned to use V additions of ~0.15% to bring about precipitation strengthening in the hot rolled condition, so raising the alloy?s proof strength above the 400MPa minimum.

Jan 1, 2004

A wide range of materials are used in hydraulic backfilling operations and the pipeline flow behaviour of these mixtures varies considerably. It is shown that despite the large differences in constituent materials and flow behaviour, a common approach can be applied to analysing the flow of all hydraulic backfills. This is extended to include a rational design approach for backfill distribution systems. The use and limitations of pipe loop tests as a design aid is discussed. Backfill quality control is identified as a key area where improvement needs to be made to enhance the reliability of backfill system operation.

Jan 1, 2001

By N. R. Williams

Black Mountain, a polymetallic base metal mine located in the Northern Cape territory of South Africa has been blessed with high grade economic ore for many years. Now that the Broken Hill orebody is nearing the end of its life, a lower grade orebody (Swartberg) is being exploited to supplement production from Broken Hill. In addition, ore from stopes in the upper levels of the Broken Hill orebody is considerably tarnished (oxidized). As a natural result, the remaining ore contains a higher percentage of magnetite, pyrrhotite and pyrite than in earlier years. Bismuth, cadmium and cobalt also occur in the ore in higher quantities. The life of the mine has been lengthened with the discovery of further deeper-lying ore reserves extending from the Broken Hill orebody suitably called the Deeps section. However, to bridge the gap between development of the new reserve and the exhaustion of the old reserve, these lower grade and tarnished (oxidized) ores have to be treated. The mine has had reasonable success in identifying unfavourable or problematic ore types and stockpiling them separately to blend in small quantities with more favourable ore. Bench and plant scale tests have aided identification of the various ore types and significant improvements in flotation metallurgical results have been seen. Copper, lead and zinc metal occur as sulphides in the ore. The mill consists of a differential and sequential flotation process that extracts copper concentrate, lead concentrate and zinc concentrate respectively with silver metal recovered in the copper and lead concentrates. This paper describes the ore blending strategy employed at the mine to maximize the econo-metallurgical efficiency of the operation.

Jan 1, 2001

By J. du Plooy

Mintek has implemented a training scheme that provides students with the experiential training requirement for the National Diplomas in Chemical Engineering and Extraction Metallurgy. This note describes the main features of the scheme and the course content, and our view of future developments in this area.

Jan 1, 1998

In surface mining operations, ultra-heavy trucks operate on haul road networks which are typically from 10?40 km in length. These road networks are often not optimally designed and maintained and as a result, identifying and remediating road functional defects is problematic. Most surface mine operators agree good roads are desirable, but find it difficult to translate this into an effective road maintenance system. This paper presents a haul road maintenance management system which utilizes an assessment of rolling resistance based on a functional performance evaluation of a haul road, together with mine haul truck operating cost models to derive the optimal frequency of road maintenance. A typical application is presented which illustrates the potential of the technique to manage maintenance as and where needed with resultant reduction in total road user costs and an improvement in service provided for the road user. Keywords: Haul road, surface mining, road maintenance, transportation, pavement design

Jan 1, 2003