Search Documents

By J. E. Conley

[Available statistics show that the demands of the American chemical industry for sodium sulphate have been increasing slightly in recent years. The supply from domestic sources, particularly in the form of byproduct salt cake from the acid manufacturers, has been tending to decease due to the growing manufacture of synthetic acid. Both hydrochloric and nitric acids are being synthesized from their elements. The natural result has been that a smaller amount of salt cake is available. Simultaneously, the expansion of the Kraft-paper industry, especially in Lie South, has brought about greater demand for sodium sulphate in that section. This demand is being met by domestic byproduct salt cake, by imported German sodium sulphate made from potash waste liquors, and by favorably situated domestic deposits of Glauber salts and tile anhydrous salt, thenardite. No shortage of natural sodium sulphate exists in the United States, but usually such deposits occur in semiarid regions far re¬moved from transportation facilities and from markets. Moreover, the major portion of the natural deposits is Glauber salt or mirabilite (Na2SO4?10H20), which must be dried or dehydrated in order to most consumer requirements. The waters of hydration represents, roughly, 55 percent of tae total weight of the crude salts and therefore has a very important influence on transportation costs. In marry instances the cost of getting even the dehydrated product to market is the deciding economic factor. Therefore, the recovery or production of anhydrous sodium sulphate from plant-waste liquors or from natural brines of suitable composition might be economically feasible.]

Jan 1, 1936

A compilation of papers presented at the Fourth WVU Conference on Coal Mine Electrotechnology in Morgantown, West Virginia, on August 2-4, 1978. Papers cover areas of electric power, electronic communications, detection and location of trapped miners, and electronic sensors and monitoring systems.

Jan 1, 1978

By J. W. Thompson

That the governor is hereby authorized to appoint a commission of seven persons, to be known as the industrial accidents commission-two of whom shall be employers of labor, two of whom shall be employees in either mines or industrial establishments of this Commonwealth, or duly accredited representatives thereof, two of whom shall be learned in the law, and one of whom shall be a person skilled and experienced in making investigations-to inquire into the causes and results of industrial accidents in the mines, mills, factories, stores, and upon the railroads, street railways, ships, wharves, and in all industrial establishments, and in all other places where men, women, and children are employed in manual labor in this Commonwealth; to study the most advanced methods for safe-guarding against these accidents; to inquire into the subject of fair compensation for those who are injured in these accidents, and for the families of those who shall be killed as a result thereof; and to study the operation and effect of the Workmen's Compensation Law of 1913. SEC. 2. The chairman of said co~mission shall be designated by the governor, and the person named on said commission as a skilled and experienced investigator shall be the secretary of the commission, The commission shall have power to employ such legal counsel and other officers and employees as it may deem necessary to properly perform its duties. SEC. 3. The secretary of said commission shall receive an annual salary of $2,400 and his actual necessary expenses; and the other members of the commission shall receive no compensation for their services, but shall be allowed their actual traveling and other necessary expenses. The salaries of any other persons employed by the commission shall be fixed by it.

Jan 1, 1920

Mercury has been used by mankind since prehistoric times. It has been, and is now, widely used in industry and medicine and has unique properties which make direct substitution difficult or impossible. At present its principal uses are for electrical apparatus, control instruments, electrolytic soda preparation, mildew-proofing paints, pesticides, and medical and dental preparations. Deposits of mercury are less common than those of other base and precious metals, but some of the deposits are very large and have been ample to meet the world's past demands. The price of mercury has had many sharp fluctuations, but in general, the limited number of producers has resulted in a more stable price structure than that of many other commodities. The United States has been one of the main producers of mercury, and from 1850 to 1961 produced 3,247,704 flasks. Yearly production since World War I1 has varied from 4,535 to 38,067 flasks. An estimate of domestic resources of mercury producible at various price ranges was prepared for each mercury mine by combining specific knowledge of mercury mineralization with estimates of potential, based on geologic information and past production history. The sum of the individual estimates for each price range is shown in a table. A parallel estimate of nationwide production potential was made from a study of past price and production relationships. These were analyzed by plotting yearly production figures against the previous year's price, expressed in dollars of constant purchasing power. An equation was fitted to the data by mathematical means and was used to extend the curve into areas of higher than historic prices. Potential production rates at various price levels were taken from this graph. The estimated yearly production rates were used to make an estimate of total potential based on the premise that production rates and reserves have a proportionate relationship. The rate of developing mercury reserves during the period from January 1944 to January 1962 is considered, and it is shown that if this rate can be continued, the mercury resources of the United States, at a constant dollar price of $500 per flask, are adequate to support a production of 60,000 flasks per year for 30 or more years. This publication contains a history and description of the mercury industry in every State which has had production and individual descriptions of all mercury properties which have reported significant production. Accompanying tables give the important facts about all known mercury occurrences.

Jan 1, 1965

By Larry Patts, Jon Hummer, Jim Noll, Aleksandar Bugarski1, George Schnakenberg, Steve Mischler, Mike Crum, Shawn Vanderslice, Rick Anderson

This study is organized under the auspices of the Metal/Nonmetal Diesel Partnership formed by the National Institute of Occupational Safety and Health (NIOSH), the National Mining Association (NMA), the National Stone Sand and Gravel Association (NSSGA), the United Steel Workers of America (USWA) and the MARG Diesel Coalition. The ultimate objective of the study is to reduce the exposure of underground miners to diesel particulate matter (DPM) and gases, and to help in fulfilling the partnership’s goal of identifying technically and economically feasible controls to curtail particulate matter emissions from existing and new diesel powered vehicles in underground metal and nonmetal mines. The majority of current knowledge on the performance of the diesel particulate filter (DPF) systems and other control technologies is based on studies done under laboratory conditions, the results then being applied the results to on-highway vehicles. According to the best knowledge of the authors, only two comprehensive studies that were conducted recently at Noranda’s Bathurst Mining and Smelting Mine and International Nickel Company’s Stobie Mine under the sponsorship of the Diesel Emissions Evaluation Program [McGinn 2001, Bugarski and Schnakenberg 2001, Bugarski and Schnakenberg 2002] offered some insight into the problems associated with the deployment of modern DPFs to underground mining vehicles. The U.S. mining industry has expressed concern that this rather limited knowledge base is not sufficient to help them comply with the rule limiting DPM exposure of underground metal and nonmetal miners [30 CFR 57.5060 2001]. The partnership agreed that a series of comprehensive field evaluations of DPFs in several underground mines was needed to determine their viability of DPF systems and establish confidence in their performance. The first in this series of studies was the one conducted in Stillwater Mining Company’s Nye Mine, Nye, Montana. This study was conducted in two phases. The objective of the first phase was to establish the effectiveness of the selected technologies in reducing diesel emissions by using an isolated zone methodology. The objective of the second phase was to assess the effectiveness of diesel particulate filters in controlling the exposure of underground miners in actual production scenarios. As part of the first phase of the study a series of tests were conducted at Nye Mine from May 19, 2003 until May 30, 2003. The results of Phase I of the study are presented in this report.

Jan 1, 2005

By R. V. Higgins, G. B. Shea

"FOREWORDIn the second year of World War II, the petroleum industry in California was taxed to near capacity to satisfy the expanded war demand for petroleum products, particularly fuel oil. With discoveries of crude oil in California declining and known reserves being depleted rapidly, conditions appeared to warrant study of the possibilities of utilizing the outcropping bituminous sandstone deposits in California for obtaining new sources of oil if the war should he prolonged. At conferences in Washington, D. C., with members of the Petroleum Administration for War and the Geological Survey, Bureau of Mines engineers emphasized the importance of determining the extent of those outcropping deposits of oil-impregnated rocks and of developing a practical process for commercial recovery of the contained bitumen to assure, if necessary, a supplementary supply of fuels. The desirability of such a study was recognized, and in July 1943 the Petroleum Field Office of the Bureau of Mines at San Francisco, Calif., in cooperation with the Geological Survey and the Petroleum Administration for War, initiated a study of the bituminouss sandstone problem. It was agreed that all mapping and geological work in connection with the study would be done by the Geological Survey, all engineering studies in developing a process for extracting the oil would be carried out, by the Bureau of Mines, and that the Petroleum Administration for War would aid in final adoption of the results in the field if circumstances warranted such action.Deposits of bituminous sandstones in California occur principally in the immediate region of the Coast Range mountains, notably at Pt. Arena, in Mendocino County, about 110 miles north of San Francisco; near Santa Cruz, in Santa Cruz County; in the Edna area in San Luis Obispo County; in the Sisquoc area in Santa Barbara County; and in the Ojai and Santa Clara Valleys in Ventura County. 4/ In addition oil-bearing sands outcrop near McKittrick and Maricopa, in western Kern County, and along the east edge of the Kern River oil field. Among the several prominent deposits of these source materials, those occurring near the cities of Santa Cruz and San Luis Obispo, and the town of Sisquoc are the largess."

Oct 1, 1948

Mercury has been used by mankind since prehistoric times. It has been, and is now, widely used in industry and medicine and has unique properties which make direct substitution difficult or impossible. At present its principal uses are for electrical apparatus, control instruments, electrolytic soda preparation, mildew-proofing paints, pesticides, and medical and dental preparations. Deposits of mercury are less common than those of other base and precious metals, but some of the deposits are very large and have been ample to meet the world's past demands. The price of mercury has had many sharp fluctuations, but in general, the limited number of producers has resulted in a more stable price structure than that of many other commodities. The United States has been one of the main producers of mercury, and from 1850 to 1961 produced 3,247,704 flasks. Yearly production since World War II has varied from 4,535 to 38,067 flasks. An estimate of domestic resources of mercury producible at various price ranges was prepared for each mercury mine by combining specific knowledge of mercury mineralization with estimates of potential, based on geologic information and past production history. The sum of the individual estimates for each price range is shown in a table. A parallel estimate of nationwide production potential was made from a study of past price and production relationships. These were analyzed by plotting yearly production figures against the previous year's price, expressed in dollars of constant purchasing power. An equation was fitted to the data by mathematical means and was used to extend the curve into areas of higher than historic prices. Potential production rates at various price levels were taken from this graph. The estimated yearly production rates were used to make an estimate of total potential based on the premise that production rates and reserves have a proportionate relationship. The rate of developing mercury reserves during the period from January 1944 to January 1962 is considered, and it is shown that if this rate can be continued, the mercury resources of the United States, at a constant dollar price of $500 per flask, are adequate to support a production of 60,000 flasks per year for 30 or more years. This publication contains a history and description of the mercury industry in every State which has had production and individual descriptions of all mercury properties which have reported significant production. Accompanying tables give the important facts about all known mercury occurrences.

Jan 1, 1965

By Philip C. Tully

This bibliography contains 3,062 different citations to technical and scientific literature about helium and alpha-particles abstracted by 13 abstract service publications during 1963. Multiple subject classification has increased the total number of entries to almost 5,000. Helium citations are listed by 23 major classifications. The number of subclassifications has been greatly increased to minimize the time required for literature search. The use of automatic data processing has been extended in compiling the bibliography.

Jan 1, 1970

By A. T. Sweet, G. Douglas Gardner

"INTRODUCTION In the ammonium sulfate process for the production of alumina from clay,,3/ the clay is baked with amonium sulfate at about 400ºC. to form anhydrous ammonium alum and free ammonia or ammonium carbonate. The alum is leached from the baked product with water and circulating liquors and is purified by recrystallization. Aluminum hydroxide is precipitated by treating thus alum the alum the ammonia or ammonium carbonate from the baking step. Ammonium sulfate is recovered from the filtrate for reuse, and the aluminum hydroxide precipitate is calcined to produce high-purity alumina. In this process, as in other acid processes for the production of alumina, 4/ a large part of the iron in the clay is extracted. The iron tends to build up in the leach liquors and contaminate the crystals, so that its elimination is one of the most important problems in the process. A number of large clay deposits occur in the Western States. Those that have boon explored most extensively 5/contain an average of 24 to 30 percent available A12O3 and 2 to 8 percent available Fe2O3. 6/ The available Fe2O3 content of various other clays ranges from less than I percent to more than 20 percent. The available Al2O3 or Fe2O3 is usually 90 to 98 percent of the total but may be much less. In generals the iron content bears no fixed relation to the alumina content and may vary widely within a given deposit."

Jan 1, 1948

By W. M. Bangert, F. S. Boericke

"INTRODUCTION Determination of the thermodynamic properties of metallurgically important compounds of chromium has been one of the activities of the Pacific Experiment Station of the Bureau of Mines. Earlier reports have dealt with the entropies 4/ 5/ of chromium, chromic oxide, and chromous and chromic chlorides, with the thermodynamic properties of the chlorides of chromium, 6/ and wits the thermodynamic properties of the carbides and oxide of chromium. 7/ Evaluation of the thermodynamic properties of chromite, FeO.Cr2O3, is desirable, as this material in impure form constitutes the only natural source of chromium of any consequence.Two general methods are available for directly determining heats of formation - (1) measurement of heats of combustion and (2) measurement of heats of solution. Neither of these methods is directly applicable at present to ferrous chromite, which accounts for the lack of previous data. Combustion of a stoichiometrical mixture of iron and chromium under conditions prevailing in a calorimetric bomb yields a mixture of iron and chromium oxides rather than chromite. None of the usual calorimetric solution media dissolve chromite at temperatures low enough for solution calorimetry. Sulfuric acid and an oxidizing agent, such as MnO2 or CrO3, are known to dissolve chromite, but the possible calorimetric use of t is medium would require long preliminary investigation. Consequently, recourse must be taken to some indirect method. At the start of the present work, the most promising method appeared to be the determination of equilibria in the selective, reduction of the iron in chromite by hydrogen;"

Jun 1, 1945

By Richard H. Spencer

The purpose of this program was threefold: (1) to identify the symptoms of poor or inadequate performance of trolley carrier phone systems; (2) to assess the root causes of performance difficulties and classify them on the basis of equipment, coupling, or transmission; (3) to propose, analyze, test, evaluate and verify means of overcoming performance difficulties. Based on interviews and discussions with knowledgeable persons, laboratory experiments, and in-mine measurements, it was determined that the major impediment to good carrier phone system performance is the extreme signal attenuation found on the trolley wire/rail largely due to the many bridging loads. Three means are identified to help overcome the performance difficulties: the low impedance trolley wire, a method of improving performance by capacitively loading the transmission line; the dedicated wire, a low-loss means of extending trolley signal coverage; the use of isolators to remove the offending bridging loads at the carrier frequency. Other subjects treated in the report are design reviews of hardware, guidelines for the use of information in the report, recommendations, and a description of a probe for measuring trolley wire current.

Jan 1, 1977

By George S. Rice

The major purpose of this bulletin, as indicated in the preface by Dr. John W. Finch, Director of the Bureau of Mines, is to give a critical review of the coal-mining methods used in the principal producing countries of Europe, to describe the reasons underlying the adoption of these methods, and to contrast them with coal-mining methods employed in the United States. The report includes discussions of various subjects intimately related to coal mining, such as geology of the principal coal fields; production and resources of the several countries; mine safety and health research; Government mining regulations; mine inspection and rescue procedure; safety lamps; fixed lighting methods under-ground; testing electric motors, mining machines, and mining explosives for permissibility; and special mining hazards, such as explosions of gas and coal dust, mine fires, instantaneous gas outbursts, ground movement and surface subsidence, and bumps. Commercial, economic, and labor problems of European coal mining, including miners' output, wages, and social-insurance schemes, as well as cost of mining, prices of coal, etc., are briefly described. It will be noted that data on most subjects are not given for Russia, which has become an important coal-producing country, owing to the lack of reliable published information concerning Russian coal mining.

Jan 1, 1939

By F. A. Rutledge, J. J. Mulligan, W. H. Kems, R. L. Thome

"As a part of the United States Department of the Interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits f nonmetallic minerals accessible to the Alaska Railroad for use in building materials in the Alaska Railroad-belt area. The results of the investigations, to date, indicate that raw materials for the production of brick products are in plentiful supply as clay in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.Shale for the production of lightweight aggregate or Haydite occurs near mile 67 on the Glenn Highway, and preliminary tests give excellent results. Physical tests are new in progress on commercial-size concrete building units made with this aggregate. Another shale deposit in the same formation was located at mile 16 on the Matanuska Branch of the Alaska Railroad, and preliminary tests give comparable results.Natural lightweight aggregate in tree form of pumice and pumicite occurs in Katmai National Monument and has been used with excellent results in lightweight-building units in Anchorage and Fairbanks. These deposits will be investigated in more detail by the Bureau of Mines during 1952.One small perlite deposit near Healy, Alaska, showed excellent expanding properties, and the product compares favorably with commercial perlites being used in the States for plaster and concrete aggregates. Additional investigation by the Bureau of Mines to delimit the known occurrence and, if possible, discover others were planned for the 1951 field season.The pumice from Katmai National Monument also was considered for use as a pozzolan in pozzolan-portland concrete. Tests by the Bureau of Reclamation indicate that the pumice sample submitted by the Bureau of Mines would be satisfactory in strength development but is not outstanding. Natural activity is good and is greatly improved by calcination at 1,4000 F. Water requirements and shrinkage also are satisfactory. However, the material is ineffective in reducing expansion owing to alkali-aggregate reaction; and, if reactive aggregate is used to make concrete, it would not insure against excessive expansion. An attempt will, be made during the 1952 field season to delimit pumicite deposits along the Alaska Peninsula more amenable for use in pozzolan-portIand concrete.Because the Railroad belt has such a rigorous climate, insulation for new construction is of prime importance. Luring the Bureau of Mines, investigation of building materials all samples were submitted for chemical analyses as possible sources of raw materials for the production of rock wool, one of the best insulation mediums. Four areas having deposits of the required constitu¬ents were located as follows: Anchorage area, with Potter limestone and argillite; Cantwell-Windy area, with limestone and shale; West Fork of the Chulitna River area, with limestone and agrillite; and Homer-Seldoyla area, with Seldovia limestone and Homer clay. It was planned to take bulk samples of these formations and submit them for testing during the 1951 field season."

Mar 1, 1953

By H. B. Hill

Virtually from the date of its discovery in December 1928 the Oklahoma City oil and gas field, Oklahoma County, Okla., has attracted national and international attention. The history of the field has been associated closely with rules and regulations pertaining to production control and proration practices. Early development was rapid, and Oklahoma City soon attained the distinction of being the first major field in which the producing wells were over a mile in depth. Before the structural features of the reservoir had been disclosed every outpost well was considered a "wildcat", so complex appeared the underground geology, The wells not only were deep and the reservoir pressures high, but the production from the early wells was a high A.P.I. gravity oil, accompanied by large volumes of gas. Several "blow-outs" and fired occurred during the early development, and the close proximity of these now unusual events to a large city gave the field much publicity, both local and national. Later, when its production threatened to demoralize the market for oil and its products, the Oklahoma City field again attracted wide publicity. The then little understood geology of the underground reservoir and the diversity of ownership of the land overlying the producing structure made orderly development and production difficult to enforce. Proration was enforced with difficulty., and the, rate of production from the field continued to increase until, on August 4, 1931, martial law was declared in all prorated fields of the State, and most of the wells in the Oklahoma City field wore shut n. On October 9, 1931, permission was granted t o reopen and prod e the wells in the Oklahoma City field. The order permitting production of the wells provided that during the period beginning October 10 and extending to October 20, 1931, all wells in the field that hid not produced more oil than specified under the earlier proration orders and that had been shut in for the required 55-day period were permitted to produce 5 percent of their last potential during that 10-day period. On November 7, 1931, the Corporation Commission of Oklahoma issued an order which divided the Oklahoma City field into the Wilcox, Arbuckle, and Lower Simpson zones for proration purposes. Wells producing from the Wilcox zone were allowed to produce 4 1/2 percent of their potential5/ from November 1, 1931, to January 1, 1932; Arbuckle limestone wells were allowed to produce 250 barrels of oil daily; and Simpson sandstone wells which had a potential of over 2,000 barrels per day or which made 3 percent or more water were allowed to produce 200 barrels of oil per day.

Jan 1, 1937

This Bureau of Mines report and its companion report (Information Circular 9142) have been prepared to assist in the preparation of prefeasibility type estimates for capital and operating costs of beneficiation of various types of mineral occurrences using current technology. The handbook provides a convenient costing procedure based on the summation of the costs for the unit processes required in any particular mining or mineral processing operation. The costing handbook consists of a series of costing sections, each corresponding to a specific mineral processing unit process. Contained within each section is the methodology to estimate either the capital or operating cost for that unit process. The unit process sections may be used to generate, in January 1984 dollars, costs through the use of either costing curves or formulae representing the prevailing technology. The mineral processing handbook includes individual cost estimation sections for unit operations associated with comminution, beneficiation, solid-liquid separation, hydrometallurgy, and special applications as well as infrastructure and plant general and administrative costs. When using this system for estimating cost data for a mineral processing facility or for checking or verifying processing costs from an existing facility, a minimum amount of background information is necessary.

Jan 1, 1987

By A. C. Fieldner

The Sectional Committee on Classification of Coals, functioning under the sponsorship of the American Society for Testing Materials and the rules of the American Standards Association, in its 1934 report recommended to the American Society for Testing-Materials5 that Specifications for Classification of Coals by Rank be adopted as tentative. These specifications, slightly modified as recommended by the Sectional Committee, in its 1935 report,6 wore approved as tentative standards by the society in 1935. The specifications rover the classification of coals according to their degree of metamorphism, or progressive alteration, in the natural eerie s from lignite to anthracite. The basic scheme of classification is according to fired carbon and calorific value (expressed in B.t.u.) calculated to the mineral-matter-free basis. The higher-rank coals are classified according to fixed carbon on the dry basis, and the lower-ran]: coals according; to B.t.u. on the moist basis, that is, containing its natural bed moisture but free of visible surface moisture. Agglutinating and weathering indices arc used to differentiate between certain adjacent groups.

Jan 1, 1935

By H. B. Hill

Virtually from the date of its discovery in December 1928 the Oklahoma City oil and gas field, Oklahoma County, Okla., has attracted national and international attention. The history of the field has been associated closely with rules and regulations pertaining to production control and proration practices. Early development was rapid, and Oklahoma City soon attained the distinction of being the first major field in which the producing wells were over a mile in depth. Before the structural features of the reservoir had been disclosed every outpost well was considered a "wildcat", so complex appeared the underground geology. The wells not only were deep and the reservoir pressures high, but the production from the early wells was a high A.P.I. gravity oil, accompanied by large volumes of gas. Several "blow-outs" and fired occurred during the early development, and the close proximity of these now unusual events to a large city gave the field much publicity, both local and national. Later, when its production threatened to demoralize the market for oil and its products, the Oklahoma. City field again attracted wide publicity. The then little understood geology of the underground reservoir and the diversity of ownership of the land overlying the producing structure made orderly development and production difficult to enforce. Proration was enforced with difficulty, and the rate of production from the field continued to increase until, on August 4, 1931, martial law was declared in all prorated fields of the State, and most of the wells in the Oklahoma City field wore shut in. On October 9, 1931, permission was granted to reopen and produce the wells in the Oklahoma City field. The order permitting production of the wells provided that during the period beginning October 10 and extending to October 20, 1931, all wells in the field that had not produced more oil than specified under the earlier proration orders and that had been shut in for the required 65-day period were permitted to produce 5 percent of their last potential during that 10-day period.

Jan 1, 1936

By David A. Hall

We present an analysis of the propagation in a uniform tunnel of semi -circular cross section that contains two axial conductors. In particular, we show that, even if one of these conductors has high ohmic loss, one of the two propagating modes has relatively low attenuation. This corresponds to the situation where an unloaded dedicated wire is used to improve radio frequency communication in a mine tunnel that contains a heavily loaded trolley wire.

Jan 1, 1978

By Dale R. Spangenberg

This Bureau of Mines Information Circular on phosphate is one of a series of minerals availability commodity directories. Nonconfidential information from the Minerals Availability Program data base covering 148 domestic and 103 foreign phosphate properties and deposits has been abstracted for use in this directory. Abstracts include applicable data on location, published reserves and resources, geology, mine and beneficiation systems, and operational information.

Jan 1, 1983

The United States Bureau of Mines is establishing a computerized mineral inventory system to help the Federal Government appraise its mineral position and prepare programs insuring against critical shortages of materials. This system, called the Minerals Availability System (MAS), is a component of the Bureau's minerals intelligence function designed to conduct and maintain an inventory of minerals important to the Nation. The MAS defines the physical and commercial availability of the mineral resources. Known resources are evaluated and classified by deposit for entry into a computer storage and retrieval system. An integral concern of these evaluations is the cost of mining and beneficiating the ore contained in specific deposits. To meet this concern, a cost handbook was developed as an aid to preparing feasibility-type estimates for capital and operating costs of mining and primary beneficiation of various types of mineral occurrences. Cost data, obtained from U.S. and Canadian companies, were used as the basis of this handbook. The handbook presents cost curves and equations for each component of the mining and beneficiation process. Factors for each cost component are also given, thereby allowing the updating of cost for time, geographic location, labor rates, and mining and milling conditions. Included in the latter conditions are items such as the length of haul, need for rock bolts, and a rock work index for ores and rocks of various hardnesses. 1.2. USE OF THE HANDBOOK Using the handbook a feasibility-type estimate falling within 25% of expected actual cost is obtainable by summarizing cost components. This handbook should not be used to determine the cost of any single component of a mining or beneficiation system, as any single component may not fall within the 257 limit. It must be understood that anyone who uses the handbook must have a comprehensive knowledge of mining and processing technology and cost estimating procedures. The handbook was intended to be used internally by the Minerals Availability System. Because

Jan 1, 2012