Search Documents

By N Vijay Mohan, K V. Balamukund, G Ananth Ramulu

Jointing of steel rods in reinforced concrete structures needs careful consideration as it renders the structure weak at the joint. The jointing is usually done at sections of structural members, where the bending moment and shear force are least. Jointing is done either by overlapping the rods or welding or by mechanical splicing. A novel method of jointing them is by inserting the two rods in a steel sleeve and cladding it on to the rods by subjecting the sleeve to explosive energy. A rod jointed in this fashion is tested for direct tension and bending when used in a reinforced concrete beam. The test results show that it is an effective method. The advantage is that a number of joints can be made in a single operation.

Jan 1, 1993

By Gary L. Self, Ronnie Daniel

With the advent of large scale blasts utilizing overburden casting techniques, it was imperative that an ultra reliable surface delay system be developed. Shock tube and detonating cord surface delay systems have been hampered by the lack of a reliable easy-touse method of incorporating multiple paths of initiation to each hole. Two new redundant nonelectric delay systems have been developed utilizing multiple signal paths to allow a higher degree of safety and reliability. The first system designed uses a combination of detonating cord and nonelectric shock tube delays to allow multiple delay paths to each hole. The second system incorporates a new all shock tube delay system which allows multiple delay paths while minimizing over-pressure by eliminating detonating cord trunk lines. These two redundant systems have been used in over 500 production blasts without any misfires due to surface cut-offs or detonator malfunctions.

Jan 1, 1989

By Don Houston

Vertical crater retreat mining (VCR) requires initiation methods that minimize debris in the borehole. The use of detonating cord and shock tube detonators eliminates debris that could interfere with subsequent loading operations and avoids the cost of using drilling equipment to clear the debris. The explosive must not be sensitive to the strength of detonating cord used, otherwise timing will be affected. “Slicing and Dicing” of product before “Air mailing” down boreholes may facilitate loading, especially in wet holes, and can result in product surrounding the detonating cord. Cord sensitivity testing confirmed that having the detonating cord surrounded by product significantly increases the likelihood of an energetic reaction. Careful formulation and testing, based on a thorough knowledge of the application and the role of ingredients in affecting performance, ensures reliable initiation and avoids cord sensitivity. The use of certain metallic nitrate salts, even in relatively small amounts, was found to significantly increase the cord sensitivity of watergel formulations. Evidence of increasing cord sensitivity includes increasing amounts of damage to product and packaging, to ejection of product from the test pipe, then cracking of the pipe, followed by deflagration then detonation of the product. Predictably, the likelihood of an energetic reaction increases with product temperature, cord strength, and borehole diameter, while it is inversely related to product density.

Jan 1, 2002

By Thomas E. Lobb, Harry C. Verakis

Blasting is a primary means of extracting minerals and ores at surface mining operations. The domestic consumption of explosives and blasting agents during the year 2001 was about 5.25 billion pounds. Flyrock is always a major concern for the blaster. Flyrock from surface blasting operations has caused serious injury and death to employees and other persons. Injuries due to flyrock and the lack of blast area security accounted for over two-thirds of all blasting-related injuries in surface coal, metal, and nonmetal mines during the period 1978-2002. Selected accidents due to flyrock and lack of blast area security in surface mining are presented in this paper. Incidents related to construction blasting are also described. Techniques to mitigate blasting accidents are discussed. These include proper blast design, driller-blaster communication, inspection prior to loading and firing the blast, removing employees from the blast area, controlling access to the blast area, and using a blasting shelter. An experienced driller could detect potential problem areas such as voids, mud seams, incompetent rocks, and other irregularities by observing the progress of drilling. The drill log should include the details of any unusual or exceptional circumstances noticed during drilling. A blaster may need to alter the loading configuration to alleviate potential problems. Basic blast design is sometimes taken for granted and assumed to be proper for the conditions encountered, but one size does not fit all. It is known from the physics of blasting that the explosive energy takes the path of least resistance. The path of least resistance could generate flyrock, depending on the blast site conditions. A combination of ‘borehole tracking’ and ‘laser profiling’ can assist in improving the design of a blast. The blaster can use these tools to adjust borehole loading to match site conditions.

Jan 1, 2004

By Gungor Tuncer, Ali Kahriman, A. Kadir Karadogan, Savas Gorgun

The environmental problems arisen from ground vibration and air blast have been faced and discussed frequently in various industries such as mining, construction, quarry, pipe line etc. where blasting is unavoidable operation. Structural damage due to ground vibrations creates great socio-economic problems for mine and quarry management as well as for the people residing in its vicinity, therefore in bench blast design, not only the technical and economical aspects, such as block size, uniformity and cost, but also the elimination of environmental problems resulting from ground vibration and air blast should be taken into consideration. With the general trend towards larger blasts in mining and infrastructure excavation, ground vibration and air blast problems and complaints have significantly increased. With increasing environmental constraints on the levels of disturbance induced by blasting operations upon nearby residents, there is an increasing need to be able to design cautious blasting with greater precision, therefore determination of maximum amount of explosive per delay for a certain distance especially in large blasts is of great importance for the elimination of these environmental problems. In another word, prediction of ground vibration components is extremely important for the minimisation of the environmental complaints. Estimating of particle velocity and other components of ground vibration with reliable approaches will give important facilities to the blasters. Although many studies had been carried out to isolate environmental problems induced by blasting in the past, a general reliable formulae has not been established yet. Due to restrictions on the complexity of ground motion, blasting and test site factors, experimental studies are still necessary for each site to minimise environmental issues. This paper presents the results of ground vibration measurements carried out during the excavation activity for contruction of an organised industrial region located nearby Istanbul in Turkey. The major rock type is granite that is encountered at this site. Within the scope of this study, in order to predict peak particle velocity level and produce a site-specific propagation curve for this site, ground vibration components were measured for blast events during bench blast optimization studies over a long period. In blasting operations; ANFO (blasting agent), gelatine dynamite (priming) and delay detonators (firing) were used as explosives. While the parameters of scaled distance (charge quantity per delay and the distance between the shot and the station) were recorded carefully, the ground vibration components were measured by means of two different vibration monitors for every event. Then, the data pairs of scaled distance and particle velocity were analyzed. The equation of scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity. At the end of statical analysis and evaluations an empirical relationship with good correlation was established between peak particle velocity and scale distance for this site.

Jan 1, 2000

By Jay P. Tobin

This paper will address the legal standards applicable to construction blasting lawsuits and offer best practices suggestions for pre-blast inspections, documenting the construction blasting work, recordkeeping, and effectively participating and partnering in the defense of a construction blasting lawsuit.

Jan 1, 2015

By Robert L. Brooks

Blasting liability problems are frequently compounded by a company's inability to effectively communicate with concerned property owners and the lack of adequate complaint documentation. Often, by the time the insurance carrier becomes involved in a blasting claim, the situation has deteriorated to the point that a solution agreeable to both parties is virtually impossible to reach. The insurance carrier, wishing to minimize their lose potential may decide to pay on a somewhat questionable blasting claim rather than be drawn into lengthy civil proceedings that would ultimately end up in front of a jury with little chance for a successful outcome.

Jan 1, 1992

By Rahim G. Haghighi, Calvin J. Konya

Fragmentation is the fundamental concern of rock blasting, serving as a measure of blasting effectiveness. Fragmentation is sensitive to the inter-relationship among the design variables which define pattern geometry. Therefore, the objective of this study was to develop a model which represented a confined bench blast and to investigate the movement of burden-rock as the length to burden (L/B) ratio was varied.

Jan 1, 1985

By J R. Brinkmann, S G. Giltner

Nearly all of the South African gold mining industry still uses fuse and igniter-cord initiation systems. Over the past 30 years numerous attempts at developing new initiation systems have not yielded a viable alternative. New initiation systems for narrow stopes are currently being developed by various concerns and the likelihood of these efforts producing feasible alternatives is greatly improved due to the recent advances in electronics technology. The greatest potential benefit of alternative initiation systems is increased production rates through improvements in accuracy and reliability of firing over that of fuse/igniter-cord. Another important feature is the capability of millisecond delay firing as this can lead to reduced stope cleaning times by way of enhanced rock throw and improved fragmentation characteristics.

Jan 1, 1989

By Conny Postupack, Jim Petrunyak, John Loope

The authors discuss the concepts, engineering considerations, and cost relationships involved in the use of drilling and blasting to accomplish backfilling and reclamation with minimum use of mechanical equipment. The four methods of reclamation now in use are reviewed, and their advantages and disadvantages are noted. Guidelines for selecting a particular method are offered in terms of applicability under varying geologic, economic, and technological conditions.

Jan 1, 1987

By Duane A. Houkom

Down time in the Oil Refining and Petro Chemical Industry is extremely expensive. Each day of non-production may easily cost several million dollars. Explosives have been accepted by this industry to solve many of its problems. Explosives offer a solution which is faster, more economical and most important, safer than many of their methods. Our specialties for these industries include: Refractory removal, industrial cleaning, metal cutting and concrete removal. This report does not include information on concrete removal.

Jan 1, 1982

By Paul V. Sterk, James Wieser

Mining in underground situations requires constant change due to changing ore bodies and economics. The Homestake Mine in its 122 years of existence has gone through numerous changes due to these factors. Recent sustained low prices in gold and ore bodies that are smaller or within mined out areas have forced the mine to reevaluate how these ore blocks will be mined. This paper will describe the design, drilling, and blasting of a complex ore block using the blind raise uphole bulk mining method.

Jan 1, 1999

By Gungor Tuncer, Erhan Bakirci, Ali Kahriman, Atilla Ozmen, O. Nuri Ucan, Savas Gorgun

There are several methods for demolition of structures but most of them depend mostly on conventional ways of using machines for breaking and crushing structural elements. However the need for lots of work force, expense and extreme amount of time for demolition, made most of these methods non-popular nowadays. Therefore, trials to accomplish a more economic and less time taking method lasted with the use of blasting. By applying controlled blasting on a suitable structure, the structure can collapse and break down to pieces in very short period of time, with no extra work force and cost. In spite of advantages of explosive demolition, the potential danger of explosives and the damage that the blasting may cause to surrondings, if not controlled properly, made people timid to the method especially in urban areas. Therefore, the pre-assumption by computational analysis has become an essential matter in the process.

Jan 1, 2002

By P. Ross, O. Rielo, P. Katsabanis

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. The paper reviews all available experimental information, ranging from small and medium scale tests in geologic materials to small scale tests at the laboratory and synthetic materials, simulating rock. Tests have been re-analyzed and discussed in terms of the information they present and the limitation of the testing environment in representing actual conditions. New results obtained from blasting experiments in specimens made of a grout have provided a clear picture of the effect of delay on fragmentation. The grout used has a strength of 60 MPa (8700 psi), density of 2.5 g/cm3 and P-wave velocity of 4000 m/s (13100 ft/s). Each block was placed in a yoke to eliminate unwanted reflections and the desired delay was obtained using the appropriate length of detonating cord between holes or sub-millisecond electronic detonators. Delays ranged from 0.1 ms/m (0.03 ms/ft) of burden to 16 ms/m (4.9 ms/ft) of burden. Fragmentation was obtained using screen analysis of the collected fragments. Delay time has been shown to be a significant parameter affecting fragmentation and back break. Generally larger fragments and less back break was observed at short values, while fragmentation somewhat deteriorated at significant delay times, compared to what was observed at intermediate delay times. The work is now extended to include the effect of energy partition on fragmentation as well as the effect of initiation point and coupling ratio.

Jan 1, 2014

By K A. Broadhurst

Over the years International Standards have produced and are continuing to work on documents related to damage from blasting and human exposure to whole-body mechanical vibration and repeated shock.

Jan 1, 1988

By Mark Bauckman

Discussion Topics • Market Needs • Technology Developments & Best Practices • Industry & Government Developments • Future Possibilities & Your Role

Jan 1, 2006

By Les W. Armstrong, Stephen B. Richardson, Neville T. Moxon

A study was carried out to determine how different degrees of stemming confinement, that is the retention of the explosives gases, effects fragmentation and movement during blasting.

Jan 1, 1993

By Robert G. Lundquist

This paper is a brief summary of work done on mining applications of high energy projectiles. Full scale field testing already completed has used cannons to drive a tunnel, drill large diameter holes, do secondary breakage in an open pit mine, and scale loose rock from inaccessible pit walls. Other applications are suggested in driving development openings, particularly raises. The method will be economically feasible only if cheap liquid propellants are developed.

Jan 1, 1977

By Robert M. Carland, Horace Gene Biggs, David Holland

At a North Carolina feldspar surface mine, the orebody contains intrusions of waste material occurring at various angles from horizontal to dipping, and varying considerably in thickness. In order to obtain optimum feed for the mill, it is desirable to obtain maximum separation of ore from waste during blasting and digging.

Jan 1, 1990

By James L. Wilcox, Douglass P. Bacon

As the U.S. Environmental Protection Agency (USEPA) and state regulators increase the stringency and enforcement of regulations concerning emissions produced by open-air detonation of energetic materials, research must provide the means of obtaining emissions data. The BangBox emissions testing program established the technical foundations for emissions characterization which have been accepted by the USEPA and other regulatory agencies; the technical issues remaining are nettlesome and require new approaches in test procedures.

Jan 1, 1996