Search Documents

By T. Wang

A new kind of mixed chelate collector was prepared in order to separate gangue (mainly quartz) and iron minerals efficiently during room temperature. The collector was was composed of two chelate collectors DES and DA. Floatation tests were carried out under 28?C with mixed magnetic concentrates of Donganshan sintering plant, and optimal test conditions were obtained, in which a direct floatation was undertaken and then a close circuit reverse floatation tests ( one roughing, one cleaning, and two scavenging), and a result of Fe grade of siderite concentrate 36.49%, Fe recovery of siderite concentrate 10.65%, Fe grade of final concentrate 66.27%, Fe recovery of final concentrate 78.25%, and Fe grade of tailing 16.22% was gained. Fourier Transform Infrared (FTIR) Spectra and Zeta potential of siderite and quartz adsorbed the DES and DA collectors before and after were measured in order to analyze the reaction between the collector and minerals. Furthermore, Molecule electronegativity of DES and DA was calculated by Electronegativity Proportionality Principle (EPP). Results showed that DES molecules have five active adsorbing sites and their molecule electronegativity was stronger while DA molecules have three active adsorbing sites, which all make the mixed collector has efficiently collecting performance. Zeta potential results of Quartz and siderite showed that at pH 11.5 both kinds of particles charged negative and at this pH value the mixed collector were mainly anionic collectors which indicate that electrostatic adsorption does not exist at this situation. FTIR results showed that characteristic peaks of the mixed collector changed before and after adsorption with the minerals, which means that there exists chemical adsorption or hydrogen bonding.

Jan 1, 2014

Pyrite and Chalcocite have different crystal lattice, with different dissolution rate in the same ac-id solution, the dissolution rate of which is accelerated with increasing redox potential, they are leached simultaneously at high redox. In present work, some methods are adopted to inhibition the bioleaching of the pyrite by controlling the redox potential. Shake flask experiment shows that the dissolution of pyrite and chalcocite is slow as redox potential <700mV(Eh), but the dissolution in-creases exponentially as redox potential>800mV(Eh), they have good selectivity at redox potential between 700mV and 760mV(Eh).

Jan 1, 2014

By T. Laxmi

This paper details the optimization of rougher Wet High Intensity Magnetic Separator (WHIMS) using response surface methodology. The optimization is in parametric form and takes account of the major operating variables in WHIMS operation such as current in ampere and grid gap, in inch. The objective is to recover ilmenite mineral from red sediment deposits of Srikakulam, India by optimizing the rougher WHIMS. We predict mineral recoveries as a function of current and grid gap. Combination of these predictions with assay data provides predictions of mineral grades and recoveries. The optimized response was validated against data derived from laboratory-scale rougher WHIMS test work, comprising (i) mineral grade, (ii) mineral recovery, and (iii) separation efficiency of the process. We observed close match between the experimental and the predicted data over most of the operational range. This paper describes how the optimization was carried out using the response surface methodology along with MATLAB. The response surface was used to closely investigate the separation of ilmenite mineral by varying ampere and grid gap. The results show that under optimum conditions, such as 3.5 amp current (0.53 Tesla) and 2 inch grid gap, the mineral grade could reach, as high as 87.9% in the concentrate with 74.3 % recovery and 74.4% yield. Keywords: red sediment, wet high intensity magnetic separator, optimization, ilmenite, placer heavy minerals

Sep 1, 2012

By A. Qaredaqi, M. Mohammadi

Wet High Intensity Magnetic Separators, for short, WHIMS are used for recovery of Iron ores with low magnetic susceptibility. A Jones patent WHIMS with "grooved plates" matrix is being used in Dry Tailing processing line in Hematite Recovery Plant at Golgohar mining & Industrial Co. for recovery of Hematite. In this kind of separators Matrices are used for increasing the Magnetic field intensity and providing high magnetic field gradient. The laboratory WHIMS in Golgohar Iron Ore and Steel research Institute is capable to provide a background magnetic field strength up to 0.85 Tesla and in presence of ‚expanded metal? matrix, magnetic field intensity could increase up to 0.9 Tesla. More than 50% of feed particles in this separator were finer than 36 micron and recovery of these particles needs more magnetic field intensity. Hence, ‚Grooved Plates? matrices with Js= 2 Tesla and 3.8 mm gap were constructed. Measurements indicated that magnetic field intensity around the matrix will increase to 1.25 Tesla. Graph of Magnetic field intensity around the matrix to background magnetic field intensity was plotted and a model with Rsquare= 0.9 was offered. In addition, magnetic field gradient and magnetic force were calculated. In WHIMS with feed top size of 150 micron, the main effective forces on separation process are the magnetic force and the hydrodynamic drag force. With assuming that the particles are smooth and spherical and the flow is laminar, Recovery of fine magnetic particles is problematic in this separator because of drag force. Considering these facts and mentioned model, finest particles that are recoverable in different magnetic field intensities were calculated. Computations illustrated that with magnetic field intensity more than 0.8 Tesla, particles as fine as 4 micron are theoretically separable but it should be noted that in practice a larger attractable particle size would be expected.

Jan 1, 2014

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

"To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.INTRODUCTIONCopper is one of the first metals extracted and the main material of choice for different high-technology applications today. Currently 80% of the world's copper comes from copper sulfide ores. However, due to the depletion of high-grade copper ores in the world and constantly growing demand for copper, the need to develop processes and technologies to treat copper resources from additional sources such as mine tailings, low grade deposits, industrial wastes and deposits with high impurity levels such as As and Sb will continue to increase (Miller and Craig, 1983). The beneficiation processes of copper-pyrite ores consisting of tennantite-tetrahedrite series minerals are generally complex. Tetrahedrite-tennantite minerals occur as fine anhedral grains intermixed with grains of galena, sphalerite, chalcopyrite, pyrite and other sulfides (Saharova, 1966). The mineralized zones of Southern Urals, Russia deposits correspond with these ore types but tennantite-tetrahedrite series are more abundant in ores at the Uzelginskoye deposit, some samples of which contain 70% of copper in tennantite form (Seravkin et al., 1994). This deposit differs from other similar copper-pyrite ores by thin mutual ""germinating"" minerals and higher content of arsenic (up to 0.8-1 %) which create additional considerable problems in enrichment (Solozhenkin et al., 2016)."

Jan 1, 2018

By T. Lang

Clay sorbents from the North Bohemian Brown Coal Basin represent important but still some-what neglected accessory raw material. Submitted paper is concerned with relation between mineral structure, sorptive efficiency and reclamation exploitation of these rocks. Characters and localities of main clay sorbents from the North Bohemian Brown Coal Basin are shortly evaluated in an introduction. In next part, methodology of mineralogy survey for these accessory raw materials is stated, it is based on diffract analyse with D 5000 Siemens X-ray diffracto-meter. At the conclusion results are stated of mineralogy analyses from several clay sorbents. The determination of the zeolite and montmorillonite localities was accentuated. The paper presents also possibilities of practical clay sorbents utilization, especially by reclamation works.

Jan 1, 2014

By F. C. Yi

Discontinuous and consecutive process was applied to probe into the Kinetics and adsorption theory for Cs+ adsorbed by Zeolites under the conditions of temperature, time and fixed-bed dynamic adsorption. It indicated that the sorption kinetics behavior of zeolite?s sorption on Cs+ is ac-cord with pseudo-secondary velocity equation, velocity constant k2=0.0005213 g?mg min-1, and equilibrium adsorptive capacity is 147.0588 mg?g-1; The equation can be expressed as: Y=0.0068X+0.0887; From the analyzing of diffusion coefficients on different temperatures and times, the coefficient of diffusion is not only related with the fabric of mineral and the character of ions but also the temperature and time; When the ambient temperature hoisted, the diffusion velocity augmented rapidly; Cs+ would get over a certain energy barrier when it enters into structure of zeo-lite; This energy is expressed by activation energy, and its value is E=131.668818 kJ?mol-1; There are two dominating adsorption mechanisms in the system of zeolite absorb Cs+: ionic interchange and surface coordinate adsorption.

Jan 1, 2014

By Alejandro Rubio-Lopetegui, Gonzalo Montes-Atenas

The occurrence of Enargite (Cu3AsS4) in hydrometallurgical plants bears a number of challenges. One question lies on how Copper and Arsenic can be selectively extracted from the solid surface structure when immersed in aqueous solution. The leaching of Enargite in ambient conditions has been extensively studied; nevertheless, challenges regarding the process kinetics and surface structures enabling the extraction process remain ill-understood. Prior knowledge indicates that different conditions of pH, Eh, temperature, speciation of the aqueous phase or variations of these parameters defines the overall rate at which metals and other elements will be transferred to the solution. One aspect that the research studies have seldom addressed involves studying the main features of the surface structures formed during the leaching process at the outmost surface atomic layer. Such structures will mediate between the solid bulk and the solution to undertake subsequent stages of leaching process. The aim of this research work is to critically analyze the state of the art of Enargite electrochemistry from the mediator formation-dissolution mechanisms standpoint occurring at the mineral-solution interface. The most probable mediator species reported in the literature were found to be: Arsenolite and Sulfur (acidic media), Covellite (acidic and alkaline media) and Tenorite (alkaline media). As a result of this analysis, it was observed that the surface speciation was not in full agreement with the previous knowledge suggested to explain Enargite leaching reactions and, therefore, modified Eh-pH diagrams are presented. The acquired insights on the surface structures rising from the Enargite-aqueous solution interactions is further revised to provide new experimental protocols towards selectively separating Copper and Arsenic through hydrometallurgical paths.

Jan 1, 2014

By Caitlin Rogers

The environmental and economic sustainability of froth flotation is dependent on effective management, which in turn improves the performance of a concentrator. In economic terms this means improved recovery of valuable minerals, in environmental terms this means effective management of acid generating tailings. Three indicators were selected to measure the performance of an integrated flotation system. The system consists of two stages of flotation; valuable mineral flotation followed by environmental desulfurisation by froth flotation. The suitable indicators were selected based on their fulfilment of four attributes. An attribute is a desired aspect of an indicator. The four attributes were: comprehensive, relevant, sensitive and quantitative. Two environmental indicators and one economic indicator were selected. They represent revenue generation from valuable minerals and environmental cost of management. The suitability of the selected indicators was shown using illustrative scenarios.

Jan 1, 2014

By F. Concha

A robust theory of sedimentation-consolidation evolved and was accepted by researchers world-wide in the last two decades of the 20th century. This theory provides a reliable method of thickener design and simulation. However, a process model, simple or sophisticated, empirical or phenomenological, is useful only if it is possible to determine, in an objective way, its experimental parameters. Research workers at the University of Concepción, together with Cettem Mineral Technology Center, created an integrated system of thickener design, simulation and control, including instrumentation, algorithm and software, which can be used by personnel in industry without specialized knowledge of thickening theory. In the paper, the development of three instruments for the measurement of pulp concentration, solid flux density and sediment compressibility is described. Each instrument uses software for data input, parameter calculation and results display. The paper also describes software for the optimization of the experimental parameter and for the design and simulation of industrial thickeners. Finally, mathematical algorithm and control strategies based on the phenomenological model are presented and compared with classical feedback control.

Jan 1, 2014

By V. V. Trusova, Shiyrav Gandandorzh, K. V. Fedotov, V. A. Domracheva

"In Russia, 1.1 million tons of mercury-containing waste are stored. The amount of mercury in soils and heaps of industrial enterprises is estimated at 3000 tons; in dumps, concentration tailings, sludge dumps of the gold mining industry up to 6000 tons have been accumulated. Mining is one of the main sources of mercury emissions in the natural environment that poses a real threat to the natural environment. At present, the process of amalgamation is prohibited and not applied in gold extraction. The application of amalgam technology in gold mining led to the accumulation of highly toxic products in the form of gold-bearing amalgam and metallic mercury, with a mercury content of dozens and even hundreds of times greater than the maximum permissible concentration for soil (1). Therefore, mercury-containing tailings constitute an ecological hazard to the environment. According to published data, at waste storage sites of industrial enterprises, up to 50 tons of mercury enter soil annually, and up to 3.5 tons pollute the air. At the same time, mercury-containing waste due to the reduction of the country's mineral resources is an additional source of mercury. Therefore, it is necessary to recycle mercury-containing waste. INTRODUCTION Paperobjective: demercurization of technogenic raw materials (amalgamation tails, discharge outlets of tailing dumps) to be recycled. Under natural conditions, the mercury usually migrates in the form of three most common compounds: elementary mercury (Hg); mercuric mercury ion (Hg+2); methylmercuryion (Hg (CH3) +. Chemical compounds Hg (II) are found in natural conditions much more often than Hg (I).The authors propose to conduct demercurization of technogenic raw materials (mercurial tailings) in two stages. At the first stage, the mercury in the form of small balls, the finest particles (drip mercury) can be extracted by applying the gravitational method. We propose a method for centrifugal processing of crushed waste in the apparatus of Itomak company, Novosibirsk, as the basis of the technological process for mercury recycling. The extraction of metallic mercury out of mercury-containing waste into commercial products, according to the technological characteristics of the Itomak apparatus, reaches 86.0% (2, 3). At the second stage, the extraction of mercury out of technogenic raw materials is performed applying a sorption method and using carbon sorbents based on fossil coals. Hard coal of the Kuznetsk Basin has been already used for industrial production of active carbons (carbon sorbents) of the KAD-iodine type, which is one of the prerequisites that determine the choice to use it for the aims of this study."

Jan 1, 2018

By R. L. Pascual, W. J. Whiten

"The froth flotation process is not well understood. Both flotation models, and the parameters used to describe the stream flows are not well defined. They in fact vary considerably in different applications. This creates difficulties is designing a simulation program suitable for use by plant personnel, consultants, and researchers. In addition to simulation, an effective simulation program can be expected to provide a range of other services.This paper shows how a process circuit simulator can be designed with sufficient flexibility to satisfy these needs, and discusses some of the additional services."

Jan 1, 2003

By Sergey Romanenko, Tatyana Aleksandrova, Karen Arustamian

"Current status of question about grinding stage effect to electrochemistry parameters of operation preparation slurry before intermediate selective flotation was assessed in the present scientific work. Needs of more detail study chemical reactions in the slurry preparation and flotation processes were shown. The ores are polymetallic sulphide type and the one are most difficult for mineral processing. The methodology allows increase information base during floatation tests. Ionometric methods and elements of neural network have been used in the study of mineral processing questions.We have also identified the relationship between the received values of the electrochemical parameters and the technological results in selective flotation. The optimal values of the electrochemistry parameters in operation of the preparation slurry before selective flotation has been found. The main effect of using the proposed methodology is to obtain scientifically based solutions to improve the technology parameters of flotation polymetallic sulfide ores. Challenging issue of selectivity of sulphide-polymetallic ores will be considered using case study of sulphidepolymetallic ores. It was shown that several factors are formed in ore grinding: formation of hydroxyl oxides of iron compounds, copper cation leaching, metal-sulphide and metal-sulphite complexes formation. The chemistry was revealed for current processes in slurry preparation operation before selective flotation. Quantitative assessment of interrelations between electrochemical parameters of slurry and process performance was given with using electrochemical control methods. Neuron network-based model was estimated based on data array and was allowed to establish optimum electrochemical conditions of metal-sulphite complex formation to provide maximum efficiency of selective flotation.INTRODUCTIONPhysical and chemical processes that take place in ore grinding have a significant impact on flotation selectivity and can cause low selectivity of the flotation process. Today this issue is given much attention. In the paper [1] it is pointed out that sulphide oxidation products and slurry components, such as sulphide ions, metallic iron and its oxidation products, have effect on flotation performance. So, metallic iron has impact on metal-sulphite complex formation as a result of oxidation-reduction reactions as follows:"

Jan 1, 2018

By P. Raghavan1

Reverse froth flotation experiments were carried out in the laboratory using two different types of kaolins for the separation and removal of coloring titanoferrous impurities from cryo-filtered clay after subjecting to high shear pre-treatment. This high shear pre-treatment consists of high shear agitation of a high solids clay slurry with the dispersant (high shear dispersion, HSD) followed by high shear agitation with the collector (high shear conditioning, HSC). After this pretreatment, the slurry is diluted and reverse flotation is carried out. One sample is from, Gujarat, India (Mamuara clay, ?MC?) while the 2nd sample is from Amberg, Germany (AKW clay, ?AC?). While MC consisted of 89% particles below 2µm and analyzed 1.06% of TiO2 and 0.29% Fe2O3 and measured a brightness of 83.4 %ISO, the corresponding values for AC are 67% below 2µm, 0.3% of TiO2? 0.49% Fe2O3 and 83.4 %ISO. The flotation performance is found to be greatly influenced by the conditions of high shear treatment. Important variables are HSD intensity (rpm), HSD time, HSC intensity (rpm), HSC time, HSD/HSC time ratio, ?HSD+HSC? total time etc. Higher shear intensities favor both the impurity liberation and collection. For both clays, it could be shown that impurity removal increases as total pretreatment time (?HSD +HSC? total time) increases up to a certain limit. For MC, the HSD time was only half or less than that of HSC time, while for AC, HSD time is at least twice (or more) than HSC time which is just an opposite manifestation. This is believed to be due to the striking differences between these two clays. Most importantly, the shear frequency is found more influential than the shear rate for the overall flotation performance for both clays. Interestingly, at high shear frequencies, i.e., when a stirrer with more number of teeth on the rotor is used, the ?HSD+HSC? total time is greatly reduced. Again, increased shear frequency helps to reduce flotation time and significantly improves flotation performance. At optimum conditions, product titania reduced to 0.35% for MC whereas the same reduced to 0.13% for AC. The product of flotation of MC measured 85%ISO brightness while that of AC measured84.6%ISO thus enhancing the value of the final product. It could also be established that the high shear pre-treatment shows better flotation performance than that due to collector dosage. Keywords: high shear dispersion, high shear conditioning, titanoferrous impurities, shear rate, shear frequency, brightness, clay recovery, Mamuara clay, AKW clay

Sep 1, 2012

By Arun Appadurai

Pneumatic transport systems play a vital role in conveying discrete particles over a sizable distance with minimal energy consumption. However if such a system is not designed keeping particle physics in mind, it leads to intractable problems which could possibly assume dangerous proportions, including but not limited to expensive redesign of the entire system. This paper describes a novel method, which harnesses the powerful technique of Computational Fluid Dynamics (CFD) to investigate a problem occurring in rotary kilns using coal as a major fuel source. In some of the sites, a unique phenomenon of abnormally high CO emission was observed and owing to the highly random nature of occurrence, it was difficult to scientifically investigate the problem and its cause. Most of the published solutions for the high CO problem tend to concentrate on the incomplete combustion aspect of the kiln and resolve the situation by increasing the air supply thereby improving the stoichiometric ratio of combustion. This paper offers an alternate correlation that relates high CO emissions to the phenomenon of coal delivery fluctuations caused by the sub-standard operation of the coal transport system. A CFD model for the coal delivery pipe is validated by utilizing the actual process data sourced from the measurements taken from a functioning plant. The results of the model are used to derive correlative conditions that point to the unstable operating conditions of the coal delivery pipe prevalent in the industry. The conclusions are summarized into a series of recommendations for optimized design of coal delivery systems which are implemented in a pilot plant. The results irrevocably prove a statistically significant reduction in CO emissions without resorting to increased air supply and power consumption. Keywords:CFD, Pneumatic Conveying, Saltation Velocity, Particle Flow

Sep 1, 2012

By S. M. Saghaeian

The studies on the product finer than 12 mm due to crushing and sizing plant of Gol-e-Gohar Iron Ore mine showed which this material contains significant amount of valuable iron minerals. Based on the carried out experimental studies on representative samples of fine hematite iron ore, a processing flow sheet was designed to upgrade iron content. This plant is known as first hematite iron ore enrichment plant in Iran which the dry medium intensity magnetic separators (with magnetic field intensity 4500 gauss and high gradient) has been used. The main objective of the plant is production of high iron product with iron content more than 61% and weight recovery more than 55% from the feed with iron content of 54%. In this plant, at first material are screened by a single deck screen (6mm), then oversize particles is separated at one stage by magnetic separator, while undersize ones at two stages. Based on the results of experimental tests, a final high iron product with iron content of 62.4% and weight recovery 63.9% can be achieved. It should mention which the iron content can be enhanced through increasing the speed of magnetic separators especially at the part of separation of finer iron ore.

Jan 1, 2014

By Mario Gerards

Maturing populations create an increase in the demand for the type of non-ferrous metals, which are used in the manufacturing of electronic products. The depletion of existing high-grade deposits, make it necessary to boost the efficiency of beneficiation processes and most importantly the yield (recovery rate of the value commodities). Increasing demand now makes it worthwhile to tap into resources, which were previously considered waste, for example secondary deposits such as tailing ponds and electronic waste. In order to achieve increased yields, increasingly finer, or even ultra-fine fractions have to be treated. In most cases, mineral characteristics such as size and density call for non-mechanical, high-capacity technologies to be used. There are various technologies that allow for the separation of fines and ultra-fines. This paper outlines the dynamics and efficiency of pneumatic flotation with emphasis on its application to the recovery of non-ferrous metals, from electronic waste. The conventional agitator flotation technology of an electronic waste processing plant was not able to recover ultra-fine non-ferrous metals satisfactorily, due to losses within the tailings. Because of its adaptability and its inherent suitability for non-ferrous metals, pneumatic flotation has been incorporated to the existing process achieving excellent results. The merit of the process lies in the state of the art technology, which does not utilize compressed air and any rotating parts, which results in a reduction in wear and energy requirement, both features of this innovative technology. In addition, the use of pneumatic flotation resulted in a significant reduction in residence time, when compared to mechanical flotation. Pneumatic technology is able to influence air bubble size in a flotation cell, by changing the speed and pressure of the slurry stream. Higher slurry velocities lead to the formation of smaller air bubbles, which is required for the successful flotation of ultra-fine particles. Conversely, decreasing the slurry velocity leads to bigger air bubbles. The optimum bubble size can be created according to different feed characteristics. This is important in case of feed fluctuations.

Sep 1, 2012

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

Roller presses are widely utilized in mineral industry for fine milling and compaction. Recently used models are providing only limited information about the material behavior in the roll bite. This paper introduces a 2-dimensional finite element model for analyzing those two basic processes. A pressure-dependent plasticity model with linear elasticity was used as a constitutive model for the particular material. Coulomb friction law was used to describe phenomena on the material/roller surface interface. Two basic roller geometries are considered: smooth (used for milling and compaction) and with cavities, commonly used for briquetting. Comparison of the results obtained from the model with experiment indicates that they are following the general trends of experimental values recorded with laboratory roller presses. It is shown, that the model is suitable to analyze material behavior through all stages of the rolling process: feeding zone, nip region, neutral plane and release section. It can predict pressure, shear stress, slip of the material over the roller surface, material velocity field, failure of the compact during release and the course of other important process variables. This allows the process engineer to gain an improved understanding, leading to a better process and equipment design and control.

Jan 1, 2003

By V. Ross

"The Upper Group 2 (UG2) reef in the Bushveld Complex in South Africa hosts an estimated 40% of the world’s Platinum Group Metal (PGM) resources. The processing of this ore via flotation poses two particular challenges: limiting the levels of chromite in the concentrate to reduce downstream smelting problems, and enhancing the recovery of ultrafine (typically -10 micron), liberated PGMs. Conventional ways of suppressing the entrained chromite, such as froth washing, is not effective in PGM operations, which are dominated by mechanical cells. The recovery of fine particles is hampered by low collision efficiencies with air bubbles, as well as oxidised surface layers especially in tailings operations. This paper documents the results of laboratory tests on a run-of-mine PGM UG2 ore, investigating the application of a pneumo-mechanical column (PMC) and its effect on PGM flotation and its selectivity with regard to chromite. A key feature of the device is the stage-wise release of aerated slurry from an agitated downcomer, thus creating conditions where the superficial velocity profiles of air and slurry change axially within the separation zone. This aids segregation of the silicates and chromite-rich fractions in the separation zone, concentrating the latter towards the bottom of the column and minimising its entrainment into the concentrate. Comparison of the performance of the PMC to that of mechanical laboratory cells under equivalent operating conditions showed improved PGM flotation kinetics and recovery. This was accompanied by a decrease in gangue recovery compared to the mechanical cells by more than 40%, thus doubling the final rougher concentrate grade from 50 to 100 g/t. Significantly, whilst the overall Cr2O3 recovery was reduced by more than 60%, the selectivity (PGM recovery vs Cr2O3 grade in the concentrate) was doubled.INTRODUCTIONThe Bushveld complex in the northern part of South Africa hosts the world’s largest reserves of Platinum Group Metals (PGMs), representing approximately 40% of the total PGE. It is characterised by three main PGM bearing reefs, namely Merensky, Upper Group 2 (UG2) and the Platreef. The Merensky and Platreef are dominated by silicates in the form of pyroxenites, and carry economically recoverable amounts of copper and nickel, in the form of chalcopyrite and pentlandite. The UG2 on the other hand is a chromitite ore with chromite as (ideally, FeO.Cr2O3) the most abundant gangue, often constituting more than 70% by mass with a PGM grade of around 4.5 g/t. Other key gangue minerals are pyroxene, feldspar and talc. The PGEs occur in a wide variety of minerals, with platinum and palladium sulphides typically accounting for about half of the total. Base metal sulphides such as chalcopyrite, pentlandite and pyrrhotite occur in only very minor amounts, accounting mostly for less than 0.1% by mass."

Jan 1, 2018

By J. A. Venter

Mineralogical studies indicate the Pt-Pd-Bi-Te class to react poorly on the flotation stimuli and indications are that these minerals are slow floaters. However, recent studies performed on a number of minerals from this class indicated strong interactions with potassium ethyl xanthate resulting in the formation of dixanthogen (only one of several xanthate species). The poor flotation response is not a result of poor interaction of xanthate with the surface. It is proposed that the oxidation products of sulfides in the process water interact with the PGM surface. To test this, the effect of thiosulfate (an important oxidation product of sulfides) was investigated by employing electrochemical measurements and FTIR spectroscopy. The electrochemical investigations indicate no strong effect of thiosulfate on the interaction of xanthate with the minerals surface as well as the reduction of oxygenthiosulfate is likely not responsible for the poor flotation response of these minerals in industrial plants.

Jan 1, 2014