Search Documents

"Air Products approached LAC Minerals in 1987 to initiate trials with pure oxygen in the leach circuit at several LAC facilities in Canada. This paper gives an overview of oxygen use and covers specific operating data from the Doyon and Terrains Aurifères mills near Val D'Or in northwestern Quebec. LAC also uses oxygen at the Macassa mill in Kirkland Lake, Ontario.In addition to the LAC facilities, oxygen is currently in use for test purposes at the Holt McDermott mine in Kirkland Lake, Ontario and the Camflo mine near Val D'Or.There are two requirements for oxygen in the cyanide leach mill. Firstly, oxygen is required in the familiar gold dissolution reaction as follows:(1) 4 AU (s) + 8 NaCN (aq) + 02 (aq)+ 2H 20(aq) - 4NaAu(CN) 2(aq)+ 4Na OH(aq)Of the reagents on the left side of the equation, the availability of gold is fixed by the ore in question. Obviously, water is available in excess, 1eaving cyanide and oxygen as the limiting constituents in the process. Most mills operate with an excess of cyanide, which is fairly closely monitored. Dissolved oxygen levels, however, are not normally watched very closely and find their own level based on the temperature, the availability of compressed air and the ability of the ore to consume oxygen.Typical D.O. levels are in the 3-8 ppm range, however levels less than 1 ppm are not uncommon for refractory ores.With pure oxygen, dissolved oxygen levels as high as 30 ppm can be achieved. (Figure #1). This greatly accelerates the kinetics of the leach reaction and may also shift the reaction further towards completion thus increasing gold dissolution slightly."

Jan 1, 1990

By J. P. Van Cruyningen, M. J. Puro

"A 2400 acre extension to the existing Tailings Area is under development at Inco's Copper Cliff Milling operations.The new area is being developed in stages as production levels dictate thus minimizing immediate capital expenditures while permitting disposal operations to proceed as further site work progresses.The first stage of the new storage site will be fully operational by early 1987 and will include a 400 acre site specific to the storage of Pyrrhotite rejected from milling circuits. The Pyrrhotite site is located in the centre of the Tailings area and is designed for water cover throughout much of its projected life.The new development incorporates perimeter dams designed to operate with low phreatic levels for maximum structural stability. Acid seepage water is collected behind secondary impermeable dams for return to the Tailings Pond.Tailings are deposited by up-stream methods permitting segregation of coarse fractions for use in future lifts of the perimeter dams."

Jan 1, 1987

By P. P. Sinha, D. N. Bhatia, B. R. Ghosh, R. K. Gupta

Medium carbon, low alloy, high-strength steels containing Ni, Cr, and Mo are used for the fabrication of various types of high-strength fasteners required for launch vehicle structures. Cold heading properties and response to hardening and tempering are the essential requirements of the material for fabrication and application, respectively. Combining these two requirements is essentially warranted in high-strength fastener-grade steels. Cold heading properties require ductility, which can be achieved through spheroidizing treatments. In the absence of a suitable spheroidizing cycle for medium carbon 3.8 Ni, 1.8 Cr, 0.3 Mo steel, experiments were carried out with a theoretical understanding of the alloy system. This paper presents the experiments and results obtained after a spheroidizing treatment, which was carried out to optimize the process. Hardness measurements were carried out and microstructural studies were conducted to assess the spheroidization process and to determine the optimal spheroidization parameters.

Jan 1, 2007

By M. N. Bassim, W. W. Tennese

"Concepts of linear elastic fracture mechanics were applied to study two cases of failure, namely an equalizing beam from a tandem rear axle of a highway tractor unit and the main beam of a flat bed trailer. In the first case, the presence of a crack, initiated by stress corrosion cracking followed by significant fatigue crack propagation produced a state of stress which was sufficient to produce brittle failure. Calculation of the fatigue life agreed with the number of cycles that the structure experienced before final fracture. In the second case, it was demonstrated that a combination of low temperature and high loading rate was sufficient to cause brittle fracture.IntroductionFailure analysis of engineering components has generally been carried out without the benefit of fracture mechanics. It is generally understood that real structures inevitably contain internal or surface flaws which under an applied load, may propagate to fracture. Fracture mechanics relates the applied stresses to the crack size in specified geometries. Since its introduction approximately thirty years ago, fracture mechanics has evolved as a design philosophy which can be used to develop fracture-safe designs. It can be also applied in analysis of failures, to ascertain if sound design and fabrication methods have been used."

Jan 1, 1985

By R. J. MacLeod

"INTRODUCTIONThe removal of water or liquid from slurries and solutions is a procedure generally present in many process industries. This has prompted the development of many mechanical and thermal devices with which, I have no doubt you are al1 familiar.In the mining industry, beneficiation of ores necessitates ' the removal of water or other 1iquid from the concentrate material. The most common method of accomplishing this is by means of thickeners, vacuum filters and rotary dryers, generally all three and in that order;The use of spray drying techniques to obtain the same end has many advantages and these will be outlined here.THE PRINCIPLE OF SPRAY DRYINGA Spray Dryer consists of a cyclone shaped chamber where hot air and atomized concentrate are introduced in the upper section. (Sec figure No. 1). Efficient mixing of these two streams produce dry concentrate and moist spent air, both of which are removed from the base of the chamber.Thermal dewatering involves the product ion of heat and spray drying has no special requirements in this area. Generally a direct fired air heater is used and the products of combustion whether they stem from the use of gas, oil or coal fuel go into the spray dryer along with quench or dilution air which is used to reduce the combustion gases to the desired temperature. This generally lies in the range of 1,000 to 1,600° F. In spite of these relatively high inlet temperatures, the spray drying process eliminates the need for refractory lining or indeed any special heat resistant metals except on the air inlet ducting. Waste heat may also be used even if a significant amount of contamination is present."

Jan 1, 1972

By Stephen Hammond

?Our own prejudices form the greatest barrier to creating an inclusive working environment.? Have you witnessed? Racism or Negative Comments about an Aboriginal Person? ?You are free to compete with all the others?, and still justly believe that you have been completely fair.? Lyndon B. Johnson

May 1, 2008

By P. H. Reynolds, S. Liaghat, A. Zarasvandi

"Darreh-Zerreshk and Ali-Abad are two relatively small porphyry copper-type deposits in Yazd Province in central Iran. They are located within the central Iranian volcano-plutonic belt, formed above the collisional convergent margin of the Iranian lithospheric plate from the late Eocene to the Miocene. This paper discusses the geochemical characteristics of the igneous rocks, and 40Ar/39Ar geochronology of plutons and alteration phases associated with the Darreh-Zerreshk and Ali-Abad deposits. The deposits are spatially associated with igneous complexes that consist of older and barren granites intruded by intermediate-composition granitoids, which are the carriers of Cu mineralization. The granites have relatively high content of Nb, Y, and K, a prominent negative Eu anomaly, and were probably derived from melting of, or contamination of mantle-derived magmas by, continental crust. Porphyritic diorites, quartz monzodiorites, and granodiorites show enrichment in light rare earth and large-ion lithophile elements, depletion in middle rare earth elements, and have no negative Eu anomaly. These intermediate-composition granitoids were derived from melting of the upper mantle or lower crust, and their differentiation was controlled partly by fractionation of hornblende. A pilot K/Ar whole-rock dating study suggests that the pre-ore granites were emplaced in the Oligocene. Dating by the 40Ar/39Ar method of nine samples of secondary biotite and sericitized rocks from drillcore within the mineralized and altered zones in both deposits yielded a well-defined age of ca. 16 Ma. This date is interpreted to be the time of hydrothermal alteration and of porphyry copper type mineralization in this part of Iran."

Jan 1, 2007

By Chen Xia, G. Deschenes, Wan-Tai Yen

"Ammonium thiosulphate is a potential replacement for the cyanide in gold leaching. However, the high reagent consumption hinders its practical applications. In order to reduce the thiosulphate consumption, chemical additives were used. The gold leaching tests were conducted on a sulphide copper-bearing gold ore with 0.3M thiosulphate, 0.03M copper sulphate and 3M ammonium hydroxide solution at 44% solids and pH 10.2. Sulphate, sulphite, amino acid and chelating agents were initially used as additives. It was found that chelating agents (EDTA and NTA) could reduce the thiosulphate consumption from 30 kg/t to 17.8 kg/t with some increase of gold extraction. The improvement from other additives was not significant. Other approaches were also attempted to reduce thiosulphate consumption with some success. The thiosulphate consumption could be reduced to about 17 kg/t by reducing copper sulphate concentration fiom 0.03M to 0.0015M; adding 0.04M of EDTA; replacing copper sulphate with 0.001M of nickel sulphate. The increase of pulp density fkom 44% to 60% solids could reduce the thiosulphate consumption to 17 kg/t as well. Limiting the dissolved oxygen content by sparging nitrogen reduced the thiosulphate consumption further to 10 kg/t. It could be concluded that the regulations of copper and oxygen supply in the lixiviant were the keys to reduce the reagent consumption.INTRODUCTIONCyanidation, as the predominant gold leaching method, has been used in mining industry for more than a century. The low reagent requirement and the high performance are the reasons for its great success. However, cyanidation cannot deal with ores containing large amount of copper, nickel, arsenic and zinc minerals. This type of ore may consume more reagents and result in a poor gold extraction. On the other hand, the carbonaceous materials may preg-rob the gold from pregnant solution and make cyanidation a problem leaching method. Further more, the high toxicity of cyanide represents another challenge to modern gold mines. In the beginning of the year 2000, an environmental disaster caused by an accidental spill in Yugoslavia was broadcasted world-widely (Gurevitch 2000). Gold mine operators are facing higher social pressures and increasing costs on environmental protections. The usage of cyanide in mining industry has been banned in some countries and locations such as Czech Republic, Japan, Turkey, California, Colorado, Wisconsin and Montana States. Thus, a non-cyanide lixiviant is required."

Jan 1, 2002

By N. W. Johnson

"Two analysis tools which have been applied to problems in industrial flotation processes are the application of kinetics and detailed mineralogical or liberation data, both on a size-by-size basis. This paper describes practical examples of the application of kineticsto examination of the entrainment recovery mechanism, the retardation of valuable minerals at the commencement of flotation sections and the resolution of problems related to valuable species with reduced rate constants at the end of sections. Examples of the usefulness of size-by-size liberation data for monthly composite samples of products from a concentrator are also described.IntroductionMuch of the published industrial flotation data on the behaviour of minerals in various size fractions have been obtained from specially conducted surveys with a duration of several hours. Such data are very valuable and provide a record of the behaviour of the entire flotation plant or sections during the interval of the survey. Some examples from the literature can be cited Cameron et al. (1971), Lynch et al. (1981), Frew (1982). Less attention has been given to the value of complementary sized data derived from compositing shift or daily inventory samples over an interval of one or several weeks with repetition of the procedure at the completion of each interval. Mineralogical point count data of the size fractions of such samples and data interpretation are rare in the literature.Kinetic data on the behaviour of valuable and gangue minerals in various size fractions have been reported often for flotation banks. In the experience 0 f the writer, there has been a tendency among operating metallurgists to ascribe problems in the flotation process to rate constant values for gangue minerals which were believed to be unsatisfactorily high. Less attention has been paid to the value for the rate constant for the valuable mineral over the length of a particular bank.Examples of the types of data which were mentioned previously have been obtained from the lead-zinc concentrator at Mount Isa Mines Limited. The various types of data have been collected to evaluate their worth in order to provide relevant information for both research and operational aspects of the plant."

Jan 1, 1987

By H. McSorley

"I note that many of you are involved in the production of zinc, lead and copper concentrates and metal, which I am the most familiar with among the non-ferrous metals. This afternoon, I will describe briefly the responsibilities of a commercial manager within a mining/metallurgical company, the basic framework of a non-ferrous metals concentrate agreement and lastly, a brief discussion of the copper, zinc and lead concentrate and metal markets.I hope this talk will contribute to a better understanding of the business between all of us and look forward to a discussion after the presentation.First of all, I work for Noranda Sales, which is the marketing and sales agent for Noranda Minerals' three operating units: Noranda Copper, Noranda Zinc and Mining Corporation. In addition, Noranda Sales acts for other mining companies in the marketing of their raw materials and metals. Noranda Sales is responsible for procuring all raw materials for Noranda's metallurgical plants, such as the Copper Group's Forne and Gaspe smelters, as well as the sale of surplus concentrates and by-products and metal products. In addition, Noranda Sales trades metals and concentrates and owns a metal brokerage business, Rudolf Wolff, a founding member of the London Metal Exchange. It does $3 billion of business in 60 countries, exporting some 80% of Noranda Minerals' output to the world.What are the responsibilities of commercial management in resource marketing to the mine and metal producers?Resource marketing and commercial administration involves assistance in establishing exploration priorities, contributing to feasibility studies, pre-production planning, product promotion and realization of income for many properties and metallurgical plants through completion of supply and sale agreements with other companie"

Jan 1, 1988

By L. Vollert

In August 2018, the first full-scale HydroFloatTM cells for the recovery of coarse composited copper and gold were commissioned at Newcrest’s Cadia Valley operation in New South Wales, Australia. The primary objective of the installation is to recover coarse value-bearing composites that are lost to conventional flotation tailings, without the need for additional power input for particle size reduction to improve mineral liberation. This paper examines the application of Eriez HydroFloatTM technology for the recovery of coarse, poorly liberated copper sulphide particles drawing on recent experience from lab scale testwork through circuit design and commissioning of the full-scale installation at Cadia Valley. INTRODUCTION In the face of declining copper head grades and a tightening regulatory environment around the use of wet tailings dams, the processing of copper ores at coarser particle sizes has become a focal point for the industry. Sulphide flotation using the Eriez HydroFloatTM is one of the emergent technologies that sits under this umbrella of coarse pre-concentration. It has been demonstrated through numerous lab and pilot scale testwork programs carried out by Newcrest and others (Awatey, Kohmuench, Thanasekaran, Skinner & Zanin, 2013), to improve the flotation recovery of sulphide-rock composite particles with low surface liberation, relative to conventional flotation technology. The HydroFloatTM technology has been used widely for the recovery of coarse potash, phosphate, coal, vermiculite, spodumene and diamonds but has never been applied at full scale in either gold or sulphide flotation. In August 2018, the first full-scale 3.4 m diameter HydroFloatTM cells for the recovery of coarse composite copper and gold were commissioned at Newcrest’s Cadia Valley operation in New South Wales. The primary objective of the installation is to recover coarse value-bearing composite particles that are lost to conventional flotation tailings, without the need for additional upfront power input for particle size reduction to improve mineral liberation.

Jan 1, 2019

Optimizing production scheduling in open pit mines is important for managing cash flows of mining operations. This paper describes a new, probabilistic, mixed integer programming (MIP) formulation which has been developed to minimize the risk of not achieving planned production targets, in terms of metal production and ore tonnage feed for the mill during production, while considering maximization of total discounted economic value. The new MIP model also recognizes that to minimize movement of excavators over long distances and accommodate equipment access, the blocks scheduled for mining within a period cannot be spread too widely. The model is applied to a laterite nickel-cobalt deposit, as an example of multi-element deposits that have complex ore quality constraints. The results show that the proposed model generates feasible schedules. When compared with traditional optimization techniques, the new model is superior in terms of minimizing the risk of not meeting production targets, especially at the early stages of production, and in terms of generating practical scheduling patterns.

Jan 1, 2006

By Euler De Souza

This paper presents a study conducted to assess sillmat behaviour during undercut mining and to provide a comprehensive understanding of the effects of arching and sillmat thickness on stability. The design study investigated the effects of such parameters as stope width and height, closure strains, orebody geometry and inclination, wall roughness, fill properties and cure time on the stability of cemented sillmat during undercut mining. Arching effects have been quantified based on centrifuge modeling studies for the different mining conditions. Observations have indicated that the degree of arching is a function of stope geometry, wall roughness, fill cohesion, and wall closure. Arching effects increased with decreasing stope width, increasing backfill cohesion and frictional resistance, increasing wall roughness and with wall closure.

May 1, 2002

By R.P. Edwards, B.C. Flintoff

Froth flotation is one of the most widely used and effective processes for mineral benefication. First introduced in 1911, flotation technology has seen many developments over the past 80-plus years. Innovations in reagent chemistry, equipment design, process analysis and process control have given design and plant engineers a powerful set of "tools" for process optimization. However, it does not follow that all flotation systems are optimized. As Klimpel observes: "The problem with the industrial flotation process is that it is relatively easy to get reasonable results, and relatively difficult to get excellent results." Klimpel [1988] While reasonable was sufficient in the past. competitive forces will make excellent necessary in the future. Judging by the activities in many Canadian plants this transition is already underway.

Jan 1, 1995

By Michael Li, Arie Moerman

"Paste backfill as a means of supporting underground mining is gaining popularity. Despite this trend, engineering and design of mine paste backfill systems are still largely based on empirical methods rather than established scientific principles. Because of a lack of sound understanding of mineral paste flow, some degree of trial and error is often involved during commissioning and operating of new paste fill systems. New operations often have to be built with flexibilities and contingencies, escalating the overall project costs.Disciplines that can lend some science to mineral paste flow include slurry transport, fresh concrete rheology, and soil mechanics. This paper reviews the applicability of some scientific and engineering principles found in those related disciplines to mineral paste flows. Examples are given to illustrate important points. The phenomenon of mineral paste flow is examined from new perspectives. Gaps in our understanding of mineral paste rheology are identified and from those some future research directions naturally emerge. Status and problems of the current engineering and design practice are also briefly discussed.INTRODUCTIONPaste backfill as a means of supporting underground mining is gaining popularity. Despite this trend, engineering and design of paste fill production and distribution systems today are still largely based on empirical methods rather than established science. One of the weaknesses of such empirical methods is the lack of scalability and transferability of rheological data from pre-engineering test phases to production phases. It is not uncommon that flow fiction data generated from expensive loop pumping tests turn out to be uncharacteristic of the paste in fullscale production. In such a case the operators have to re-climb the learning curve, sometimes with expensive disruptions to the mining operation."

Jan 1, 2002

In order to maintain a production rate of 6,000 tonnes per day from underground at the Williams Operating Corporation, two independent mining areas were required which created a long narrow sill pillar between them. During initial mining of the sill pillar there were a number of significant ground falls [LeBlanc and Murdoch, 2000] and in March 1999, with no active mining ongoing in the sill pillar area, a rockburst of magnitude 3.0 Nuttli occurred. Extensive ground support was designed and installed to withstand events of similar magnitude [Bawden and Jones, 2002]. A mine wide microseismic system was installed to monitor mine induced seismic behaviour over the entire mine. The area most directly affected by the 1999 rockburst was rehabilitated using a highly ductile support design. Along with microseismic instrumentation, the areas were instrumented using conventional SMART Cables and SMART MPBX?s. Subsequent to this, the area was impacted by a large number of high magnitude seismic events [magnitudes between 1.7 and 3.5 Nuttli]. The ground support performed very well during these events, providing confidence in the mine?s ability to control the ground under severe rockburst conditions. Analyses of microseismic and conventional instrumentation, combined with numerical analyses of sequence alternatives, were used to develop an optimal mining strategy for the sill pillar area. The selected strategy involved utilization of instrumentation data and calibrated model results to analyze yield zones in the sill. The analyzed ?yielded? zones were assessed to be low seismic risk. Initial mining in the sill was then concentrated in these low risk areas, with the objective of further concentrating stress into the remaining seismically active area, in order to induce ultimate failure of the sill. Continuing large magnitude seismicity and resulting damage in the remaining ?high seismic risk? area, led to abandoning a second portion of the footwall access and the strategic decision to extract a stope near the centre of this zone in order to force final failure of the sill pillar. During execution of this plan two large magnitude seismic events occurred resulting in destressing and final failure of the remaining sill pillar. The paper provides a detailed description of this ?strategic mine sequence driven self-destressing process? and the implications to final extraction planning in this area of the mine.

Apr 1, 2005

By Q. Zhang, J. A. Finch

"Sphalerite flotation in the absence of copper activation at moderately alkaline pH has been observed in laboratory studies. An in-plant test of this observation was conducted at Kidd Creek Mine LTD. using a portable minicell flotation circuit. The results confirm that raising the pH causes sphalerite flotation.The testwork with the minicell circuit is described. The circuit, built around 2, 51 cells donated by the Noranda Technology Centre, was funded by Air Liquide and NSERC. It includes a data acquisition system to monitor continuously dissolved oxygen, pH and Pulp potential.INTRODUCTIONFlotation of sphalerite is normally practised by adding CuSO4 as an activator under alkaline pH. Recently there have been a number of laboratory and plant examples of sphalerite flotation without deliberate addition of cu++ ions (Girczys, 1972; Mukherjee, 1976; McTavish, 1980; Marouf et al., 1986; Mielczarski, 1986; Leroux et al., 1987; Palsson and Forssberg, 1989; Sandoval-Caballero et al., 1990; Zhang et al., 1991).In batch tests, with a sample of Pb/Zn ore from Polaris, Leroux et al. (1987) found that sphalerite became floatable after adjusting pH to 9. 5-11: they ruled out natural floatability or the formation of elemental sulphur on the surface but suspected iron hydroxy compounds were responsible. Sandoval-Caballero (1990) conducted a continuous minicell test at Brunswick Mining and obtained a 44 % Zn recovery and 40.5 % Zn grade concentrate without deliberately adding CuS04 at pH= 10.5. With single mineral studies, Zhang et al. (1991) revealed good sphalerite floatability (over 80% recovery) in pH range 8 to 11 and found that this floatability was related to pH, dissolved oxygen (DO) level and Fe++ species present in the system.To explore further the conditions under which sphalerite can float without addition of CuSO4 , a continuous pilot test using minicells was performed at Falconbridge Ltd., Kidd Creek division. The set-up is briefly described (a more detailed description is given elsewhere in these proceedings) with emphasis on the data acquisition system - dissolved oxygen, pulp potential and pH were monitored continuously. Results of testwork investigating pH, CuS04 addition and gas composition are presented."

Jan 1, 1992

By E. Roman, M. Brissette

"For its end of life, Kemess Mine processed its difficult-to-treat hypogene ore from the east pit, which is a lower grade copper and higher pyrite content gold ore. Metallurgical testwork showed that improvement was possible with finer grinding. In July 2010, small grinding media were introduced into the regrind mill resulting to a nearly 50% decrease of the power draw with a finer grind, an increase of 1.1% in the final copper grade, an increase of 1.2% in copper and 2.9% in gold recoveries at the cleaners. The overall recoveries of copper and gold increased by 0.6% and 1.3% respectively.INTRODUCTION Kemess Mine was located at 430 km North West of Prince George in North Central British Colombia. Its production started in May 1998 by Royal Oak Mines and was acquired by Northgate Exploration in 2000. Kemess reached its end of life production with its last of production on March 9th, 2011. The concentrator nominal capacity was 56,000 TPD consisting of a primary gyratory crusher feeding two identical conventional SAB circuits totalizing 35,840 kW available for grinding. Rougher flotation consists of four parallel rows of eight 130 m³ tank cells to produce a concentrate of 2% Cu and 6 gr/t Au which was pumped to a 5 m x 10.8 m regrind ball mill. The regrind installed power was 4,480 kW to generate a final grind of 80% passing 40 microns. This product fed the two stage cleaner flotation circuit, first stage being two parallel rows conventional 17 m³ Denver cells and second stage, two 3.3 m x 11.0 m flotation columns in series, designed and constructed by Kemess, to produce a 22% copper concentrate grade. The cleaner flotation middlings were returned back to the regrind mill (Froehling, Mohns, Roman & Grady, 2005; Froehling, Mohns, Rajwani & Fullam, 2007). The large copper-gold porphyry deposit was composed of 15% of oxidized supergene and leach cap ore and 85% of hypogene ore having three major alteration zones, mainly characterized by their sulphur/sulphide content. Chalcopyrite is the main copper mineral species with minor bornite. Gold was mainly present as free gold or electrum. The first alteration zone consisted of a phyllic alteration characterized by moderate and intense sericite alteration which had the highest mill throughput and twice the mine grade when in contact with the supergene horizon. The second zone consisted of a potassic alteration characterized by more competent groundmass and moderate to intense quartz stockwork which had a slightly lower mill throughput. Finally, a third alteration found beneath and on the east side of the deposit having almost no quartz stockwork and hardened groundmass, sulphide content is two to four times more. This zone had the lower mill throughput with significant drop in the mine average gold and copper grade. Through its mine life, the average life of mine copper head grade was 0.21% Cu and 0.64 gr/t Au. Head grades began to decrease from 2008 to be substantially lower in 2011 as shown in Table 1."

Jan 1, 2012

By Ammar Henchiri, Godfrey McDonald

"Breakwater Tunisia S.A.’s Bougrine mine is located in a semi-arid region of Tunisia characterized with Triassic salt domes. Due to extensive agricultural land-use in the mine area, a zero-discharge tailings facility design and high water recycling rates to the concentrator were chosen to minimize the environmental impact to the surrounding area. The process water supply has an accumulation of naturally occurring salts due to high evaporation rates and the need to recycle 70% of the process water. The elevated salt content of the process water had an adverse effect on the efficiency of the flotation reagents, which led to the production of lower quality zinc concentrate.The impact of the water salinity on the zinc concentrate quality was documented by extensive laboratory testing. A feasibility study was prepared and a decision was made to install a reverse osmosis plant for desalination of the process water. A plant was constructed during 2000 which currently supplies up to 85 m3/hr of de-mineralized water, equal to approximately 45% of the total process water requirement. The salinity of the process water decreased from about ten to twelve grams per litre before installation to less than three grams per litre. Together with minor modifications to the concentrator circuit, Breakwater Tunisia has increased the zinc concentrate grade from 50% zinc to 55% zinc without compromising the zinc recovery rate of approximately 84%.This paper discusses the successful installation of a reverse osmosis desalination plant that allowed Breakwater Tunisia to improve the grade of the Bougrine mine zinc concentrate and thus increase the net smelter return.INTRODUCTIONBreakwater Resources Ltd., through a wholly owned subsidiary, Breakwater Tunisia S.A., acquired the Bougrine underground mine and related assets in September 1997. During the winter of 1997/1998, the company rehabilitated the mining equipment, modified the concentrator circuit, developed a new mine ventilation system and prepared a new mining production program. The mine was reopened on May 2, 1998 and was in commercial production as of June 1, 1998."

Jan 1, 2003

By I. P. Barbosa, P. S. M. Soares, I. O. C. Masson

"Permanent magnets have been applied extensively to several electronic products such as printers, TV sets, microphones, microcomputers and headphones, presently manufactured in large scale by industrial economies. Sm-Co alloys represent about 20% of the world market for permanent magnets and their industrial processors generate 20-30% of magnetic scraps which can be recycled. This paper discusses a process route to recycle SmCo5 using acid treatment, solvent extraction of Sm and electrowinning of Co. The results confirm the feasibility of the alternative proposed. Basic operational variables are suggested as guidelines to design a plant for recycling magnetic scraps.The use of hydrometallurgical processes to recycle scraps from the industry of permanent magnets has been suggested in some recent papers related to recycling of metallic alloys [ 1 ]. These research efforts might be understood as a worldwide tendency towards the development of self sustainable metallurgical processes which mean the reduction of environmental impacts.CETEM -Center for Mineral Technology leads in Brazil several research programs concerning recycling and treatment of industrial residues. The work on samarium purification and concentration by solvent extraction, producing also a solution of cobalt sulfate as partially reported here is one of these programs. Previous results related to the sulfuric acid digestion of SmCo5 are presented somewhere else [2]"

Jan 1, 1997