Search Documents

By William D. Gallant, Thomas M. Barczak, Carol Tasillo

"This paper describes the results of full-scale testing of several multi-layered wood crib configurations that were tested in the Bureau of Mines mine roof simulator in cooperation with the Cape Breton Coal Research Laboratory and Cape Breton Development Corporation of Sydney, Nova Scotia. Nine different crib configurations currently being used as wood packwall supports for advancing longwall applications in Canada were evaluated. Configuration parameters understudy included the aspect ratio (height-to-width relationship) and percentage of solid material used in the crib construction. Test results and generalized wood crib behaviour are discussed in detail. Recommendations are made concerning crib constructions to maximize strength and stability. A cost benefit analysis of multi-layered wood crib configurations is made. A comparison of laboratory results and underground observations of several wood packwall supports in the Sydney coalfield suggest in situ load capacity is less than that measured in laboratory testing. Reasons for the apparent decrease of in situ load bearing capability are described.IntroductionA cooperative effort was undertaken by the U.S. Bureau of Mines with the Cape Breton Development Corporation (CBDC) and the Cape Breton Coal Research Laboratory (CBCRL) to evaluate the behaviour of gateside packing materials used in advancing longwall mining applications in the Sydney coalfield. As part of this effort, full-scale tests were conducted on wood packwall supports in the Bureau's 3-million pound (13.3 MN) active load frame.Nine different pack configurations were evaluated as part of this study. The wood packwall supports were multi-layered crib constructions from 6 in. (0.15 m) by 6 in. (0.15 m) cross section timbers using timber s 30 in. (0.75 m) and 60 in. (1.5 m) in length . The percentage of solid material in the crib constructions varied as illustrated in Figures 1 and 2. A summary of crib constructions is provided in Table 1."

Jan 1, 1991

By Isabel F. Barton, J. Brent Hiskey

Chalcopyrite (CuFeS2) is the earth’s most abundant copper ore mineral, but is refractory to leaching with sulfates, chlorides, and other common lixiviants and oxidants. This has led to increasing research into alternative lixiviants for recovering Cu from chalcopyrite. Here, we review the leach kinetics of chalcopyrite in glycine, ionic liquids, and methanesulfonic acid, compared to baseline ferric sulfate and ferric chloride. Glycine (CH2NH2COOH) has long been used in applications such as biocatalysis and electroplating, and has recently been examined as a lixiviant for whole ores and concentrates of both copper and gold. It is nontoxic, biodegradable, and capable of strongly complexing Cu2+. Compatible oxidants are peroxide, dissolved oxygen, and ferric sulfate. Chalcopyrite leaching rate in glycine is chemical reaction-controlled, but the effects of grain size and the reaction orders with respect to lixiviant and oxidant concentrations and mass transfer vary. The use of ionic liquids as a leaching agent for chalcopyrite has been extensively investigated in recent years. This system is based primarily on the use of the imidazolium molecule (C3H5N2), which is a planar 5-member ring structure. This lixiviant has been applied to the leaching of chalcopyrite in the form of pure mineral, concentrates, and ores. Kinetics of ionic liquid leaching of chalcopyrite vary substantially depending on the type and concentration of ionic liquid. Methanesulfonic acid (HCH3SO3) is one of the newest lixiviants available in leaching, having only been examined in the last decade. It has been examined as a substitute for sulfuric acid, since it is less corrosive, is biodegradable, and breaks down to carbon dioxide and sulfate over time. The rate of copper leaching from chalcopyrite by methanesulfonic acid is controlled by diffusion and exhibits a strong dependence on oxidant type and concentration. Despite promising reaction rates and total extraction by some of these novel lixiviants, comparison with baseline ferric sulfate and ferric chloride systems makes it doubtful that any will be commercially viable in the near term. Only at very high reagent concentrations and temperatures, and/or very fine grain size, did any of the systems perform comparably to the much cheaper ferric chloride at extracting Cu from chalcopyrite. Most had similar overall reaction rates and total extraction to ferric sulfate, which is relatively common and cheap. However, the leaching kinetics of these novel lixiviants offer valuable insight into the dissolution behavior of chalcopyrite in various systems.

Jan 1, 2019

By Tomoya Kawasaki, Tatsuya Motomura, Yutaka Yasuda

Saganoseki Smelter, one of the largest copper producers in Japan, currently operates a single flash smelting furnace to produce 450,000 tons of new copper annually. The smelter used to employ two flash furnaces, and integrated the two into one in 1996. Since then, various improvements to its facilities and technologies have been made to increase productivity. To upgrade the operation efficiency, "stability" was considered a key issue, and the measures were taken to increase the operation and facility reliability. Currently, the furnace is running at a feed rate of 215 DMT/h, while the furnace utilization has been maintained at 97%. This paper outlines recent improvements that have made to increase furnace productivity and efficiency.

Jan 1, 2014

By Neil Schofield

"The Pine Creek gold mineralization is associated with saddle reefs and quartz and quartz sulphide veining within the Enterprise Anticline. The anticlinal structure is complex and the mineralization was considered prior to development to be dominantly strata controlled. Gold grades vary up to 160 gin 1.5 m core samples with coefficients of variation in excess of three.The estimation of ore reserves for such a deposit must account for both the geological complexity and the extreme variability of gold grade.This paper describes the structural and variogram analysis of the gold grades and demonstrates the importance of incorporating the geological model in such an analysis. Variogram interpretation is greatly improved and greater insights into the finer geological structure areprovided. Part 2ofthis work presents the application of multigaussian kriging to reserve estimation for deposits with highly variable grade and which consequently demand highly selective mining operations. IntroductionThe Enterprise Gold Mine is situated some 220 km southeast of Darwin in Australia's tropical north. Gold is believed to have been discovered there in 1869 during the construction of the overland telegraph line.From 1894to 1915, some 75 000 ounces of gold were produced from 121 000 tonnes mined mainly by Chinese leaseholders. From 1906 to 1915, government-sponsored drilling led to the sinking of the Enterprise Shaft to 79 m and several drives were developed. Mining ceased because of war.Since late 1980, Goldfields Exploration Pty. Ltd. had explored on several mining tenements near Pine Creek under joint venture with the title holders, Enterprise Mines NL. This work culminated in the development of the current mine which opened on October 29, 1985.Feasibility studies to determine the economic viability of mining were based on ore reserves generated by project geologists using a sectional polygonal approach tuned to the interpreted geological control of the mineralization.The study motivating this two-part paper covers are-estimation of the recoverable reserve s using the geostatistical approach of multigaussian kriging developed at Stanford University, (Verly, 1984)."

Jan 1, 1988

By Todd Kennedy, Kurt Tischler

"This paper presents the field experience of Siemens with regard to Gearless Drives in the mining industry … We consider the elapsed production hours of Siemens Gearless Drives to be extensive enough to provide a reliable estimation of availability calculated on the basis of data representing repair time, downtime, and operating time. The users of Siemens Gearless Drives confirm an availability of more than 98% after exclusion of some major issues. The paper addresses all of these major issues of Siemens Gearless Drives, describes successfully applied corrective measures, explains the influences on the design of the drives, and lists the downtimes associated with each of these issues. INTRODUCTIONThe first Siemens Gearless Drive in mining began operation in 1980 and was installed on an iron ore grinding mill. As of September 2011, 40 Siemens Gearless Drives will have accumulated 136,000 machine days of operating time. According to pure rules of statistical analysis, this accumulated operating time may be too low to be used for a sample of field data to provide precise statistical values of availability, however we consider it large enough to provide indicative values of worthwhile consideration. This paper deduces the availability statistics of Siemens Gearless Drives in the mining industry from information received from end users and factors in all major issues that Siemens has experienced with our Gearless Mill drives. This paper does not consider Gearless Drives in other industries such as the cement industry. The cement plants, especially in the northern hemisphere, interrupt production for several months in the winter. This lengthy downtime is used to maintain the complete plant including the mills, their motors and their drives. The mining industry has more stringent and higher production requirements. In the mining industry, production must run 24 hours per day, 365 days a year."

Jan 1, 2012

By Sukumar Bandopadhyay, Arunapuram Sundararajan

"Unique production and environmental problems are associated with multiple seam mining where dragfines are used for overburden and interburden removal. On the production side, the problems are decreased dragfine efficiency in chopdown operations, the general need for spoil rehandle, complications in sequencing stripping and coal handling operations, and potential stability problems in highly stacked spoil. Many variations of dragline methods have been reported in the literature to encounter these problems. Because of the physical properties and peculiar hydrology of sub-arctic region mining of multiple seams in such areas probably could not be done with the methods used in temperate regions.The properties of thawed material would make spoil hard to place in a stable manner and thus would influence the mini sequence. For instance, multiple seam mining which requires some rehandling of spoil and prolonged exposure of overburden and interburden material might be precluded by the instability of thawed spoil and therefore mining techniques have to be modified. Since the deployment and operation of a dragline in modes different from conventional schemes will affect productivity, it will be necessary to study the effects on production of changing the dragfine operational schemes. This paper presents a heuristic simulation model of multi-seam dragline operation of a sub-arctic mine that can be used to analyze the handling of overburden and detailed study of the dragfine performance."

Jan 1, 1986

By Pierre Antoine Dhaiti, Gilbert Sergerie, Michel Dagbert, Jean-Maurice Brodeur

"Quality of iron ore is generally determined by several factors which can be correlated or independent. Among these f actors, we generally find per cent iron, silica, magnetite or hardness. Forecasting the short- and long-term fluctuations of these f actors in the future pit is an important feature of mine planning in these deposits. Computer simulation provides a realistic answer to these questions. It allows to generate values for the most important quality features of each shovel load with the proper correlations between them as well as between one load and the next being fully reproduced. Then different sampling schemes f or grade control or blending facilities can be examined on the simulated data. The mechanics of the simulation procedure and its potential applications are described in an example.IntroductionThe purpose of this paper is to illustrate the use of in-situ grade simulation in the planning o f the grade control in an iron ore min e. More precisely, given a production unit of given size, we need to know how many samples have to be collected in that unit so that we ca n recognize its grade with a reasonable precision. Conclusions that we would like to arrive at are of the type: with 4 blasthole samples we ca n get the iron grade of a 10,000 ton bloc k with less than a ± 2% Fe error 95% of the time.The approach t hat we take to solve this problem is simulation. We simulate the grade of samples and the grade of the block that contains these samples. We repeat the simulation for hundred s o f blocks. By comparing the sample grade with the block grade in each case, we determine the actual number o f blocks where the difference sample-bloc k is less than a given limit."

Jan 1, 1983

By L. E. Reed, I. G. L. Sinclair

An exploration program seeking kimberlite pipes, the common primary hosts for diamonds, Was' conducted during the years 1979 through 1982 in the James Bay Lowlands of Ontario by Selco Mining Corporation (now the Mining Division of BP Resources Canada) and Esso Minerals Canada. The area to be explored was selected on the basis of its regional geological setting, and because of the known presence of kimberlite indicator minerals in the region. The primary exploration technique was low level airborne magnetic surveying, followed by detailed ground geophysics. This work located many pipe-like bodies, with diameters of a few hundred metres, as well as several dykes. Targets located by these geophysical methods were drilled, intersecting a total of45 intrusions, consisting of34 alkaline diatremes containing tuffisitic breccias, 7 carbonatites, and 4 massive alnoites. K-Ar determinations indicated ages of 152 Ma and 180 Ma for two of the massive alnoites. The texture and general mineralogy of the tuffisitic breccias are similar to those of diatreme facies kimberlites, but detailed examination of their mineralogy and chemistry demonstrated that they lie within the alnoitic rather than the kimberlitic compositional field. Although the exploration program did not lead to the discovery of true kimberlites, it did demonstrate the presence of a large, previously unknown province of alkaline volcanic activity, which has no surface expression.

Jan 1, 1991

By B. M. Das, F. Claridge, V. K. Garga

Coal, as well as a large part of other minerals in Canada, is produced by surface mining methods. This has resulted in short and long-term accumulation of waste rock in dumps. Two main problems arise from the flow of water through these dumps: stability of dumps and the impact on stream flows. In recent years, a number of mines have started placing waste rock in valleys for general disposal or far constructing mine access road ways. All these have created challenges in the following areas: effective design of dumps and flow-through dams; stability monitoring of the structures; environmental impacts downstream by way of increased amount of fines in suspension, sedimentation, and toxic substances; and long-term status of flow and flood. Similar situations also exist in many civil engineering structures. This paper discusses the status of rock drains and the immediate and future research needs.

Jan 1, 1990

By J. H. Gray

"IntroductionIn 1980, Fording Coal Limited started conceptual planning studies which led to major changes in the long-range mining plan at their Fording River Operations. These new plans have been completed and are now in operation.To assist personnel in a timely completion of this major revision to the long-range plan, existing in-house drill hole data base and scheduling systems were used and a computerized Mine Modelling and Planning System was purchased. With these tools, plan s were developed which led to completion of initial access to the peak of Eagle Mountain and the start of mining operations in March 1983. As mining area s open up and new geo logical data is obtained, detailed plan s are being extended and revised.With the geology and mine plan s on line, this work can now be done with less effort and plans ca n be adapted to provide flexibility in mining operations. Changes in market conditions can be accommodated by moving mining operations into different seams for different coal types. The computer systems are used to revise pit designs and schedules accordingly."

Jan 1, 1986

By A. Himsley, E. Byleveld

"With reference to the chemical constraints underlying the ion exchange process for uranium recovery, a generalized view is presented on the actual and the achievable efficiency of the process. The area considered is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution.A comparison between actual plant results and the chemical requirements shows that:(a) Unless new and better ion exchange resins are developed, no dramatic change in equipment size and resin inventory is""anticipated. (b) Elution efficiency, especially for sulphuric acid, may be improved considerably. More concentrated eluates may beproduced at lower chemical consumption. A possibility of achieving additional purification solely by ion exchange is discussed.IntroductionThis paper presents a generalized view of the actual and the achievable efficiency of the ion exchange processes for urannium recovery. The study is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution. The ultimate efficiency attainable with ion exchange is dietacted by the chemical reactions underlying the process. The most sophisticated technology cannot change the diffusion rates in the ion exchange resin nor make the uranium loading exceed its equilibrium valueThe design of an ion exchange plant for uranium recovery involves a considerable number of parameters as a result of the wide variety of pregnant solutions produced from different orebodies. Therefore, a generalized approach of the ion exchange process inevitably neglects some parameters which maylead to significant variations in apparently identical situations.The uranium concentration in the pregnant solution, together with its pH, are the principal variables which determine resin loading and residence rime in the ion exchange system. On the elution side, the type of eluant and its concentration will determine the contact time required and the amount of eluant needed to strip the resin. The temperature, the properties of the ion exchange resin, the total dissolved solids in the feed solution and the competing ions are other variables that affect the chemical performance; these, however, may be considered as a correction of the principal parameters if one is interested only in general trends."

Jan 1, 1980

By M. Scobie, G. R. Baiden

"This paper describes recent developments at Inco Limited, Ontario Division, in the field of information systems for automated mining. A CA TV cable network has been combined with a broad spectrum radio antenna system to allow the supply of voice, data and video services to underground mining. The system formed the basis of a field experiment at the Copper Cliff North Mine of the Ontario Division in 1990.The experimental information system was developed to supply underground mining with voice, data and video services to mobile and stationary locations. In order to test the communication system, telephones and radios were linked together with the outside phone lines for voice communication. Stationary data was implemented on a SCADA (Supervisory Control and Data Acquisition) system for mine monitoring and control using PLCs (Programmable Logic Controllers), while using personal workstations for the mine planning and engineering functions. Stationary video was installed in the experiment to observe crushing, conveyor transfer points and skip dumping areas. Mobile data and video were tested by the teleoperation of an LHD. The functions supplied to the vehicle were monitored through a computer, with control being maintained through a standard radio interface and real time video pictures for the operation of the machine.This paper discusses the field testing of the information system and results achieved to date. It concludes by discussing the options considered to be open to provide information systems for future automated mining."

Jan 1, 1992

By D. S. Harries, R. I. L. Guthrie

"The use and development of scientific disciplines involved in heat transfer technology, related in general to steel masses and in particular to batch annealing, is demonstrated.The measurable benefits of cooperation are tabled; on industry's side, this includes a 10 to 20 per cent decrease in annealing time, and a corresponding higher productivity potential. The returned benefits to the academic engineer include the development and refinement of new computer algorithms related to heat transfer mechanisms.IntroductionThe object of this discussion is not really to describe an improvement in the batch annealing operation, but to use the project as an example of joint work between industry and the academic field. Both parties have derived a number of substantial benefits. These benefits will be listed, of course, but the batch anneal project will be used just as a typical example of cooperation. Why it happened will be explained, what actually happened will be described and finally some thoughts about areas in the field of heat transfer, where cooperation will continue in the future, will be highlighted. The paper will close with a message.Industry OverviewAt the outset, perhaps it should be understood that, in general, the Research Department at Dofasco believes that the universities and their staff are not destined for the problem-solving role in industry. Its opinion is that the university staff is best suited to the gathering and dissemination of knowledge. There are other more professional problem solvers for industry, including the steel industries' own individual investigation groups. Dofasco, therefore, looks to its academics for consultation. It benefits by bouncing ideas off them, and through rubbing shoulders with them in such a way that their knowledge can be tapped, and thus establish more effective scientific routes. In addition, the younger and brighter engineer s can broaden their scope through the intellectual contact with experts. The university professors can, it is believed, benefit through closer contacts with result-orientated research. They can also develop an appreciation of the fiscal control necessary for industrial investigations, without government subsidies, grants, etc., and with massive overheads."

Jan 1, 1982

By V. Casaletto, L. Widdifield

"Equipment capable of higher production requires more sophisticated maintenance programs. Reduction in fleet size through use of modern technology requires higher utilization and greater availability.Caterpillar's maintenance control system program will display the capabilities of computer technology in a maintenance environment. Utilizing such resources will provide increased availability, lower inventory requirements, fewer last minute disasters, and lower cost per ton for maintenance. High production from premium quality equipment can only be realized by good planning and care, executed by maintenance and operating personnel acting cooperatively.IntroductionAccurate information is the key to accurate decision making. In today' s competitive industry, mines' teeter on the brink between profit and loss. Their survival will be predicated on their ability to retrieve, analyze, and formulate accurate information regarding the operating costs of mobile equipment. This paper deals with the impact of managing equipment operating costs and introduces a computerized control system designed for monitoring and controlling these costs.Caterpillar has produced several computerized modelling programs designed at taking the guesswork out of equipment selection and management. The most basic of these is Equipment Investment Analysis (E.LA.). This model compares two or more alternatives over the projected life of the machine. It deals with comparisons in the owning and operating costs of equipment, as well as, their productivity over a specified period of time.In order for a computer model to be credible as a decision making tool, it must be simple to use and the results measurable and accountable . Caterpillar has introduced several computer models to assist the industry in selecting and managing an equipment fleet. These programs allow the user to predict and monitor the operating costs and production capability of mobile equipment. They are often used in the machine selection process to select equipment which best suits a mine's long-term cost per tonne objectives. After the optimum selection is made, Caterpillar's Maintenance Control System provides an efficient management tool to monitor and verify the data used in the selection model."

Jan 1, 1992

By A. P. Williams

"This paper presents an overview of plant electrical systems in general, a discussion of the problems that may occur due to plant growth, the maintenance required to maintain the reliability and safety of the electrical system, and the selectivity of the relay protection system. It is divided into two main areas: short circuit levels within the plant electrical system; and relay protection systems.This information is directed at maintenance supervisors, mine managers and electrical superintendents who have been away from detailed short circuit and relay coordination calculations for some time. It points out the potential problem areas within an operating plant electrical system. Short Circuit LevelsTheoryThe electrical equipment in a plant such as breakers, switches and starters has two short circuit ratings, the momentary rating and the interrupting rating. These ratings may be given in MVA or current (amperes) depending on the equipment and manufacturer's preference. Since for a three-phase system MVA and amperes are related by the formula"

Jan 1, 1987

By V. K. Karra

"A simplistic algorithm jar simulating the rod or ball mill Bond grindability test applied to ores and minerals is presented. A performance comparison between the present algorithm and a previously published algorithm by Kapurot, modified in this work jar a fair evaluation, is also given. A worked example is furnished jar leading the reader through the various calculations.IntroductionThe Bond grindability test is widely used for the prediction of the power requirement of an industrial grinding mill. The procedures for conducting this test in either a ball or a rod mill are available(1). In the case of a ball mill, batch grind abilities have been correlated to Bond grindabilities to help monitor day-today variations in ore grindability for the purpose of plant control( 2,3). Of special interest is the algorithm presented by Kapur(3) for the simulation of the Bond test. In practice, the test lasts from 6 to 14 cycles (4 to 10 hours). With this algorithm, one can predict the Bond grind ability using information available from only the first two cycles.Sometimes the prepared feed for the grindability test contains too much fines compared to the total product desired at the mesh of grind under consideration. In such a case, the operator separates the fines from the test feed and adds to the remaining coarse fraction an equal amount of fresh feed. This combined feed then forms the feed to the first cycle of the test. In the present work, Kapur's algorithm is modified to include this special case. A new and relatively simpler algorithm is also presented. Statistical equations relating work index to pertinent variables are also given."

Jan 1, 1981

By Nitin Bhavsar, Kaushik Vakil, Lakshmikanth Reddy, Sanjay Sarkar, Tathavadkar. Vilas, Bhavin Desai, Raghavendra Adiga

Gold and platinum group metals (PGM) do not dissolve in sulfate electrolyte from anode during electro-refining of primary copper. The PGM form solid ‘slimes’ which accumulates at bottom of the electrolytic cell. Typically, 8 to 10 ppm silver is present in copper cathodes, which is equivalent to almost 2% of silver loss during electro-refining. The silver can be cemented with cathode copper as soon as it is dissolved into the electrolyte from anode or during entrapment of slime particles in cathode. Over a period of time, the concentrates grade has deteriorated and change in type & amount of impurities in concentrate has resulted in higher silver loss during refining process. Therefore, an in-depth investigation was carried out in both fire- and electro-refining processes to understand the root causes of higher silver loss in copper cathodes. The detailed characterization and the plant data analysis were carried out. The results of study revealed that higher silver loss in 3rd crop cathodes as compared to 1st and 2nd crop cathodes from same anode. In anode silver was present in two forms, dissolved in copper (solid solution) and in slime phases such as Cu2-xAgxSeTe. SEM-EDX study of anode cross section confirmed higher silver and oxygen content in central region (core) of anode as compared that in both air and mold sides. This is due to non-uniform cooling of anode which was confirmed by the solidification modeling. Higher concentration of oxygen & silver at core of anode rised Ag+ concentration in electrolyte and slime particles during 3rd crop. The results of study were used to optimize the anode cooling process and also electrolyte chemistry to reduce the silver loss. The details of study carried out are discussed in this paper using the results of modeling, characterization and experimental studies. INTRODUCTION In the electrolytic refining of copper, fire refined copper anodes are used as raw material. Anodes contains copper of the range 99.5 to 99.6%, rest being the impurities. Hence, the purpose of the refining is (1) to remove the impurities so that final cathode conforms to the LME specifications and also (2) to recover the precious metal from the anode copper. When anode is dissolved, most of the impurities reports to the anode slime settled at the bottom of the cell, and rest dissolves in the electrolyte. Dissolved impurities remains in electrolyte and are removed during electrolyte recycling. However, sometime dissolved impurities and slime particles get entrapped in cathode due to disturbances in operational conditions. Metals dissolving in the electrolyte are the elements such as Ni, Co, Fe, Zn. The electrode potential of As, Sb and Bi being close to that of copper, these elements partly dissolve in the electrolyte. Noble metals like Ag, Au, Pt and Pd are generally insoluble and are thus expected to report to the anode slime. A small amount of the sliver content from the anode is dissolved in the electrolyte. Because the dissolved silver electroplates on the cathode at a smaller applied potential than copper, the cathode typically contains up to 8 ppm of silver. This is referred to as ‘silver loss’ in cathode (Cooper, 1987). Fortunately, silver is a rather benign impurity in copper due to its electrical conductivity being higher than copper. However, higher silver loss in cathode is loss of revenue for Copper smelter due to significant difference in their LME price.

Jan 1, 2019

By R. W. Lawrence, A. Bruynesteyn

"Pre-oxidation of refractory pyritic concentrates by biological leaching to enhance the recovery of gold and silver in cyan ideation has been investigated. The results of laboratory tests on three concentrates are presented. In all cases substantial increases in precious metal recoveries were obtained following the pre-treatment. For one concentrate, gold recovery of 81% was achieved following an 87% oxidation of pyrite, compared with 24% recovery by direct cyanidation of non-oxidized concentrate. Gold and silver recoveries from the other concentrates were increased from the range 60-78% to over 90% and from 80-86% to over 98% respectively. Operating parameters are discussed and methods of maintaining high oxidation rates are evaluated. Methods of employing this pre-oxidation technique in commercial practice are described.IntroductionMany of the gold and silver deposits now being developed contain precious metals finely disseminated in sulphide minerals such as pyrite. These ore s often present considerable resistance to metal recovery. The ease with which gold may be extracted is usually related to grain size and its manner of distribution within the host mineral. In many cases, a significant percentage of the gold may occur in submicroscopic form, or in solid solution with pyrite, so that even very fine grinding fail s to liberate the metal for recovery by cyanide leaching. Such ores are often termed refractory. Even in cases where liberation by fine grinding is practicable, high cyanide and lime consumption may be experienced due to the presence of specific sulphide minerals, and poor metal recovery may result.Pre-oxidation methods for refractory ore s and concentrates are commonly used to improve precious metal recoveries. Roasting, for example, as a pre-treatment to cyanidation, removes harmful constituents by oxidation or volatilization, and liberates gold from pyrite. In some cases, however, this method of pre-oxidation can result in poorer metal recovery, particularly of silver, due to fusion and the formation of clinker, and the formation of compounds which consume cyanide in the subsequent metal recovery stage. Difficulties in compliance with environmental pollution regulations may also be encountered."

Jan 1, 1983

By J. W. Bingay

The expansion of the mining industry, with other industries, of course, is dependent upon a supply of fresh capital from year to year. Mining is a speculative form of investment, though there is a wide range of risk as between indiudual undertakings. All of the leading financial writers, nowadays, agree that expansion is being seriously interfered with by the unprecedented load of taxation Canadians are carrying. Individuals have less for investment and corporations are obliged to defer necessary expenditures in order that the demands of the taxing authorities may be met. Naturally, speculative investments such as mining exploration suffer first. Undoubtedly, a great deal of cash raised by taxes, if left in the hands of individuals and corporations for investment and expansion, would have been far more beneficially used and would have developed the country more than any use made of it by the government, in the way of bonusing new industries, or the undertaking of large schemes of development. Government undertakings of this nature are often entered into without a proper knowledge of cost and probable return. Expert expenditure of the same sums by business men or corporations undoubtedly would generally produce more prosperity for the country as a whole. The absolute necessity for lower taxation is being increasingly known to the public at large, and eventually it is hoped that our governments will see the economic impossibility of continuing the present rate of expenditure. The successful Finance Minister of the near future will not be the one who can borrow the most money.

Jan 1, 1924

By Alan G. Galley

"Advances in our knowledge of the petrochemical attributes of deposit environments and of the character and extent of hydrothermal systems associated with certain deposit types has resulted in increased application of lithogeochemistry to exploration programs. Lithogeochemistry can be used to vector an exploration program toward an area of high potential through the use of a series of collapsing scales of analysis from a tectonic subprovince down to a particular stratigraphic segment. In the case of volcanogenic massive sulphide (VMS) deposits this involves the recognition ofsuitable volcanic domains, and the identification of subvolcanic intrusions and cogenetic felsic extrusive complexes. The recognition of chemical vectors within regional-scale alteration zones and associated chemical sedimentary rocks allows the geologist to identify the stratigraphic units with the most potential for hosting a base metal deposit.An integrated lithogeochemical program requires the judicious use of major, trace and rare-earth element and isotopic analysis. Standard discriminant plots may be employed to identify suitable tectonic and lithologic environments. Analysis of the chemical and mineralogical variations in broad-scale, semi-comfortable alteration zones provides a useful set of vectors to VMS mineralization. These may include contouring raw data, element ratios on XY plots, normalizing data against known rock values, or calculating mass changes in alteration zones."

Jan 1, 1995