Search Documents

By Fred Horne

1N THIS PAPER, the writer proposes to limit his comments to few generalized phases of the subject, based on his personal experience in the midwestern United 'States and in one section .of the Coal Branch in Western Alberta. The following statistics are submitted to show the importance that strip mining has assumed in the coal mining industry of the United States. In 1914, 1,281,000 tons of strip coal were produced, amounting to 0.3 per cent of the total production. In 1948, the total was 13~,505,000 tons, representing 23.3 per cent. In 1949, the percentage figure dropped slightly and this can be partially accounted for by the labour disturbances prevalent throughout the year. In 1914, there were 48 power shovels and draglines being used in the stripping of coal; in 1949 there were 3,712, not to mention other types of coal stripping equipment such as bulldozers, tractors and scrapers, rotary excavators, and stackers. At the bituminous coal mines in Western Canada, strip mining was introduced only a few years ago, two of the major reasons for its development being the need for increased production during the war and post-war years and the need to hold the line on increasing production costs, but even in these few years the percentage of strip production has in-creased to such an extent that some mines that, five or six years ago, were producing all their tonnage from underground operations are today obtaining up to 80 per cent of their total output from strip mines.

Jan 1, 1951

By C. W. Jr. Waterman

INTRODUCTION MY SUBJECT is one which would require several speakers and many hours of time for adequate presentation in all its many facets. Because of the widely varying market requirements and coal seams mined, the coal industry of the United States bas of necessity employed many types of preparation facilities to satisfy its needs. Predominance of Baum-type jigs, however, bas marked the mechanical cleaning installations since the early thirties, and these machines continue to hold the lead. CLEANING As a matter of record we find that, at the end of 1948, we had 480 mechanical cleaning plants in operation. Of these, 19 used air cleaners only,?400 used water washers only, . and 61 used dry and wet washers in combination . Due to the increased use of spray water underground on cutting and mechanical mining equipment, there has in recent years been a marked downward trend in dry cleaning installations. In fact, the moisture in dry-cleaned fines has been increased to such an extent by spraying that recent dry cleaning installations have incorporated thermal drying ahead of the dry cleaning units in an effort to overcome the varying and increasingly higher moisture percentages in their raw coal feeds. While on the subject of dry cleaning, it might be well to bring to your attention one of our most recent developments in this art. I refer to the McNally-Brusset vacuum jig.

Jan 1, 1951

By M. Uszko

The paper presents the conditions for determining the selection of methods for methane drainage in Polish hard coal mines. Various factors for the evaluation of methane drainage performance are used, including the methane drainage effectiveness ratio. However, as will be discussed there are limitations to the methane drainage ratio approach resulting from the characteristics of the deposits extracted in Kompania Weglowa S.A. coal mines.

Aug 1, 2013

By F. R. Erick Mulder

"AbstractTwo bottom-hole samples have been taken from two new completions in the Turner Valley field, Royalite Lowery No. 8 on the west flank and Royalite No. 73, which was deepened into a lower fault block, on the northeast flank. From the bottom-hole oil of Royalite Lowary No. 8 a synthetic sample was prepared to simulate the original fluid in the reservoir, saturated at the gas-oil contact conditions. The sample from Royalite Lewery No. 8 has been shown to be the original fluid present at this well and represents the oil phase near the oil-water contact in• the reservoir. Complete chemical analysis, P.V.T., and viscosity data have been obtained on these reservoir fluids, which represent the range of saturation from the gas-oil to the oil-water contact in the Turner Valley oil structures. Sampling techniques and the application of the analytical data to reservoir conditions and field operations are discussed. Super-compressibility curves for an average separator tail gas have also been prepared. These data have not been available before. They will be of fundamental value in futu.re reservoir engineering studies of this field and will also serve as a guide in determining operating practices."

Jan 1, 1950

By D. Kao, J. Gogal, S. Humphrey, T. Byrne, M. Davoodi

"High total and dissolved uranium values were noted in the process water at the Cigar Lake Operation (CLO) during early production start-up period, whereas significant levels of dissolved uranium had not been observed previously at similar operations. The excess dissolved uranium resulted in higher demands on the water treatment plant, along with higher operating costs, environmental risks and some unrealized revenue potential. A species balance indicated that uranium was leaching into solution in the grinding, dewatering, and storage circuits under normal operating conditions. Jet boring, water recycle, ball milling, and the use of Pachuca tanks for ore storage results in a highly oxidative environment, which is favourable to leaching.This paper will outline the testwork performed to identify the conditions under which the uranium leaches into solution and to determine required conditions for uranium precipitation. Maximum uranium leaching was found to occur under normal operating conditions (pH ranging from 7.0 to 8.5); testwork indicated that both lowering and raising the pH can significantly reduce the uranium leaching. Analytical results combined with the batch scale testwork indicate that the uranium solubility is associated with carbonate species in the ore. Uranium precipitation was maximized at pH values greater than 10.5 or less than 6, corresponding well to carbonate leaching and precipitation values from literature. Higher precipitation efficiencies were noted at high pH ranges.As a result of this work, a pH control system has been implemented in the Pachuca storage vessels and thickener prior to water treatment plant on a trial basis. Caustic soda is recommended for pH control due to ease of operation, economic viability and material requirements and downstream constraints."

Jan 1, 2016

By Lopatka. M. J.

This paper presents the results of 3 tons skid steer 6x6 wheel robot drive system field tests. The aim of the investigation was verification of assumed data for drivetrain diesain and forces identification in the drivetrain system during maneuvering and crossing obstacles. Robot has hydraulics drive system with motors in the wheels and hydraulic suspension system. The neded drive torque on wheels was determined by pressure measurnig on motors.

Aug 1, 2013

By Zoltan Hajnal

Magnetic studies have been carried out on 88 surface and 157 underground samples from the Coronation Mine area of northern Saskatchewan. The intensity of the surface samples was compared to trace element determinations from the same locality. A good correlation was found between the titaniferous constituent of the rocks and the intensity of magnetization. From the direction of the remanent magnetism, two virtual geomagnetic poles were determined -latitude 12° 54' North, longitude 158" 17' West; and latitude 23" 42' North, longitude 163° 45' West. The sulphide ore specimens showed anisotropic susceptibility characteristics. A relationship was found between the measured maximum susceptibility values of the ore specimens and the direction of the tectonic forces which are considered to have formed the structure at the Coronation mine. Introduction T HIS paper summarizes the results of a study of the magnetic properties of samples from well-known Precambrian formations. The observed data give information for an interpretation of the magnetic field conditions in Precambrian times. The high magnetic intensity values indicate the importance of the study

Jan 1, 1965

By Neville Jordison

Indirect, gravity flow, heat exchangers have become a well established technology in mineral and metallurgical process plants. The technology is a conventional heat exchanger using high efficiency plates, with a free flowing bulk solid on one side of the exchanger and a fluid on the other side. This simple concept leads to many opportunities for achieving greater energy efficiencies in process plants. Indirect heat exchange is much more efficient than direct heat exchange using air such as in a fluid bed or rotary device. When air is used directly, large fans are required, it may also be necessary to chill the air, both high consumers of energy. By contrast, using water as the cooling medium requires only low horsepower pumps, typically only 10% of fan HP. Furthermore there are no stack emissions with the requirement for removal of dust or emissions. Indirect heat exchange also creates the opportunity to recover energy. This can work in two ways: energy can be recovered from a hot bulk solid, to heat pressurized hot water for steam generation or preheat air. Alternatively recovered energy from elsewhere in the plant in the form of hot water, steam, air or thermal oil can be used to preheat a bulk solid.

Jan 1, 2011

By R. Shamsodini, A. Poor Zaeif Doost, H. Haji Amin Shirazi, M. R. Garmsiri

"With columns being installed in rougher section at Miduk Copper Complex, the rougher feed mainly reports to rougher-scavenger cells. To evaluate the efficiency of regrinding circuit, we conducted flotation experiments on samples of the feed and the products of the regrinding circuit. The grade difference of these products at 85% recovery was considered as the efficiency index. Results show that, with weight recovery of the rougher-scavengers the efficiency of the circuit increases. Exclusion of the rougher-scavenger concentrate from the feed to the regrinding circuit, resulted in an increase in the efficiency index from 10.12 to 17.6%.INTRODUCTIONThe flotation circuit at Miduk Copper Complex consists of five flotation columns as roughers and ten mechanical cells as rougher-scavengers. According to design criteria, 75% of the final product was expected to be produced by the rougher columns, while most of the feed consisting of liberated valuable particles is introduced into rougher-scavengers. To liberate locked particles, the rougher-scavengers concentrate is introduced into the regrinding circuit (see Figure 1 below). The regrind mill is in reversed closed circuit with a secondary hydrocyclones cluster, and the cyclone overflow is introduced into three parallel cleaner columns. Cleaners concentrate reports to concentrate thickener and the column tailings is introduced into six mechanical cleaner-scavenger cells. The cleaner-scavengers concentrate reports to the regrind circuit(Figure 1)."

Jan 1, 2012

By G. E. Rowan

"DURING the dark ages, the cherished dream of chemists was to find a process for converting base metal into gold. Many a wealthy-but-gullible patron lost a fortune in the search. Men who work with metals today are a bit more realistic. I haven't heard of a metallurgist who expects to develop any one alloy that will resist all corrosive media. In the field of stain-less steels, there are about forty different types of alloys that are used where corrosion is a •problem.A stainless product is ordinarily selected because it offers one or more of the following qualities:(1) Resistance to corrosion (2) Resistance to oxidation at high temperatures (3) Good mechanical properties at room temperature (4) Good mechanical properties at high or low temperature (5) Attractive appearance (6) Ease of maintenanceToday we are interested in discussing the stainless steel family of alloys because of their .ability to resist corrosion. We• will not try to explain the Theory of Corrosion. Let us assume that, when surface potential and oxide formations are properly controlled, iron will resist attack in various chemi.cal solutions. The addition of alloying elements to iron does this for stainless steels. The principal stainless alloys used by various Canadian industries are listed in the accompanying Table."

Jan 1, 1959

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"Abstract - The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3 and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995

In April, 1961, a large pillar was removed by blasthole mining methods at Inco's Murray mine. More than half a million pounds of explosives were used to break 2,120,000 tons of ore in a single underground blast. The 5, 10 2-inch boreholes, involving 435,815 feet of drilling, were loaded over a three-week period, using conventional explosives and short-period electric caps. From this blast, more than half a million tons of ore have been removed to date (April, 1962) through slusher trenches situated in the footwall of the ore body. T HE Ontario Division of The International Nickel Company of Canada, Limited, operates six underground mines and two open pits in the Sudbury district in the north-central part of the Province. This paper describes the removal of a large pillar at the Murray mine (Figure 1), where 2,120,000 tons of ore were broken in a single underground blast by the blasthole mining method. This is the largest underground blast achieved to date (April, 1962) at Inco mines.

Jan 1, 1963

By J P. Bolduc, P. E. Pelletier

Preceded by brief general considerations such as the development of the mining industry in. the Province of Quebec, the choice of plant location, the types of problems studied etc., the paper gives a complete description of this new research and treatment center for metallic, non-metallic and asbestos ores. Facilities for carrying out operations in the three sections of the plant -the sampling section, the ore treatment section and the asbestos section -are fully discussed as well as laboratory facilities for (a) the preliminary testing of ores prior to pilot plant treatment and (b) the grading and testing of asbestos fibre. AT THE beginning of the century, the annual value of the mineral production of the Province of Quebec stood at the $2,500,000 level. Twenty-five years later, it was just under $24,000,000. In 1950, half a century later, it was slightly in excess of $200,000,000. But in 1959, in the span of only nine years, it

Jan 1, 1962

By R M. Ennis, J. C. Botham

This paper is one of a series pre-pared to study the role of fuels and reductants in metallurgical processes, especially from the viewpoint of Canadian requirements. The object of these studies is to provide a reason-ably authoritative interpretation on the interrelation of fuels in light of the considerable changes that have taken place in the Canadian energy field during the past few years. Previous papers in this group have dealt with the problem generally, and specifically in terms of the development of the iron and steel industry of Western Canada. These latter papers, presented at the Symposium on Iron and Steel in Western Canada held in Edmonton, Alberta, on September 8-9, 1959, surveyed the ferrous processes of interest for use in Wes tern Canada, especially with regard to solid fuel requirements. At that time it was evident that there was a need for a similar study of the fuels aspect of the non-ferrous metals industry.

Jan 1, 1961

By B. D. H. Knights, N. B. du Preez

The recovery of the economy of the Democratic Republic of Congo has allowed for the rapid increase in production of copper from this region, while the increased price of cobalt continues to support the recovery of that country’s economy. This has enabled the modernization of the process technology used, particularly the change from direct electrowinning of copper to solvent extraction-electrowinning. With this change has come a variety of technical challenges in optimizing the recovery of cobalt from these sources. In this paper, we discuss aspects of the flowsheets for the production of cobalt from the ores of the DRC and Zambia, highlighting the technological improvements that have been made. Following this description of the practice, we assess the challenges of further improving the recovery and purity of cobalt from these sources. INTRODUCTION The African Copperbelt (Figure 1) is by far the biggest producer and holds the greatest reserves of cobalt (Sheed, 2015). However, the ores of this great mining region are extracted primarily for their copper content, and cobalt is a by-product. The ratio of copper-to-cobalt is between 6 and 20 to 1, with the ores from the DRC richer in cobalt than those from Zambia. The overall supply of cobalt, shown in Figure 2, is increasing due to an increase in demand for its use as a battery material. Cobalt is used in superalloys, hard metals, pigments, catalysts magnets, tyre adhesives, lithium-ion rechargeable batteries, and wear-resistant coatings, amongst others. Although these generic categories persist, Figure 3 shows how the relative usage of cobalt is changing due to the uptake of electric vehicles in China and Europe. Cobalt is a key element in lithium-ion batteries, and because it is widely anticipated that electric vehicles will be legislatively encouraged, it is anticipated that the demand for cobalt will rise. This anticipated increase in demand resulted in an increase in the price for cobalt, to which suppliers responded over-eagerly, and the price has dropped dramatically in the first few months of 2019, as shown in Figure 4. However, there is a clear cycle of price peaks in cobalt’s history.

Jan 1, 2019

By H. H. Bird

Kilembe is situated in the foothills of the Ruwenzori Mountains in Uganda. Precambrian stratiform copper de-posits are currently being mined at a rate of 90,000 tons per month. Complex ore structures and variable ground conditions have led to diverse mining methods in the past. New mining areas contain more shallow-dipping, highly contorted orebodies, in heavy ground. Cut-and-fill mining will be practised in the future. The geology, mining and milling are described.

Jan 1, 1968

By G. M. Scamans

In the past ten years there has been considerable penetration of aluminum automotive body sheet (ABS) into automotive structures. The exponential increase in demand is resulting in major investments in heat treatment and finishing capacity across the globe. Line speed and tonnage throughput is limited by the continuous heat treatment (CHT) floater furnace rather than the cleaning and pretreatment section where electrolytic treatments that offer higher line speeds should come into favour and roll coating of pretreatment should predominate. The capacity limiting surface texturing pass will either be eliminated or moved to the finishing line or a dedicated mill. The key to making aluminum both embedded carbon and cost competitive with steel for more and more affordable classes of vehicles lies in recycling of both prompt scrap and, in the longer term, end of life vehicle scrap. For the first time scrap separation technology is available that can compete effectively with hand sorting and can sort aluminum shredded vehicle scrap into wrought and cast alloys and then into individual alloy groups. The challenge is to use more end of life scrap in alloy formulation whilst at the same time extending the property range in terms of both strength and formability.

Jan 1, 2015

By G. M. Scamans

In the past ten years there has been considerable penetration of aluminum automotive body sheet (ABS) into automotive structures. The exponential increase in demand is resulting in major investments in heat treatment and finishing capacity across the globe. Line speed and tonnage throughput is limited by the continuous heat treatment (CHT) floater furnace rather than the cleaning and pretreatment section where electrolytic treatments that offer higher line speeds should come into favour and roll coating of pretreatment should predominate. The capacity limiting surface texturing pass will either be eliminated or moved to the finishing line or a dedicated mill. The key to making aluminum both embedded carbon and cost competitive with steel for more and more affordable classes of vehicles lies in recycling of both prompt scrap and, in the longer term, end of life vehicle scrap. For the first time scrap separation technology is available that can compete effectively with hand sorting and can sort aluminum shredded vehicle scrap into wrought and cast alloys and then into individual alloy groups. The challenge is to use more end of life scrap in alloy formulation whilst at the same time extending the property range in terms of both strength and formability.

Jan 1, 2015

By M. Jayaraman

With the ever increasing demand for commodities, due to changes in lifestyle and increase in population, people are striving to find ways to keep up. Mining is one essential element in the solution. Though being a powerful boost to a country?s economy, mining can have disastrous effects in the absence of waste management practice and technologies; because of the harmful heavy metals and toxic chemical waste that is generated as a by-product in mining operations. It is an established and documented fact that pollution is a major concern for communities having to live with it. Disproportionate water consumption significantly impacts local rivers and ponds thereby reducing freshwater availability and have given rise to social conflict. In light of these misgivings, management and treatment of mine water and waste has gained considerable attention recently. In this paper, we summarize some of the treatment methods that can be adopted by mining companies to reduce their environmental footprint. Appropriate treatment solutions depend on various factors including available space and capital cost for treatment solutions, type of mining waste generated, current state of the mining plant, geographical location, and other location specific issues. Incorporating waste and water management solutions as a priority within mining operations is critical for addressing increasing regulatory requirements and a starting point for initiating other Corporate Social Responsibility (CSR) programs. Collaboration among mining companies, NGOs, local community, and government facilitates successful projects which build trust leading to long term relationships. In this paper we also talk about the benefits of implementing a CSR project that captures the focus of local communities and allows the mining company to focus on operations. Implementing a sustainable business model that incorporates the broader community impacted by projects will continue to benefit even after the mining company ceases operation in that location. The challenges involved with implementing effective CSR projects, which require measuring and reporting effectiveness to create a positive social, economic, and environmental impact is also presented in this paper.

Aug 1, 2013

By Aaro E. Aho

Yukon, one of the most potentially accessible, relatively undeveloped, regions of Canada, has major mineral possibilities. The Klondike placer gold fields and the Mayo silver-lead ?district are the sole major producers but large base-metal re-serves have been discovered in re-cent years and important asbestos deposits are now being explored. Several major exploration companies are active in this region despite short seasons, permafrost overburden, remoteness, lack of transportation, and resultant high costs. Pro-posed new roads can be expected to accelerate development. At ?present the major future mineral possibilities are considered to be lead-zinc, copper, aslbestos, silver-lead, gold, and mineral fuels. These and other mineral possibilities are outlined for various geological subdivisions of Yukon. Major favourable metallogenic features of Yukon include complexity of rock types and structures, widening of the Cordillera with cross-trends, and variety and quantity of mineralization found even with limited prospecting. Comparisons with southern 'British Columbia and the U.S. Cordillera suggest that further exploration will result in discovery and development of more major ore deposits and reserves which will eventually revolutionize economy of mining in Yukon. Such mineral resources, with interior petroleum and natural gas possibilities, and ?huge coastal hydroelectric power potential, are the foundations of a much larger future mining industry in Yukon.

Jan 1, 1958