Search Documents

The New Zealand opportunity NZ?s only significant phosphate deposit 1 million tonnes imported annually - mostly from Morocco US $180/t + $75/t freight

May 1, 2013

"This paper presents results of ongoing research being carried out at the University of New South Wales into improved methods for estimating rock mass strength. In this paper the rock mass strength of Hawkesbury Sandstone is assessed. An estimate is first made based on an extensive database of intact rock strength data being collated by the author and the assumption that the rock mass strength can be determined following the GSI approach. The resulting strength envelope is then compared with nine documented case studies where stress induced failure has occurred in tunnels excavated within Hawkesbury Sandstone. The case studies cover a range of conditions:• construction dates from 1880s to 2006• spans from 3.2 to 12.5 m• depths from 17 to 124 m• excavation methods of drill & blast, roadheader and TBM.Finite element modelling is used to assess the likely magnitudes of the stresses present at the time of failure. The finite element models are interrogated to provide the values of major and minor principal stresses in and around the mapped failure zone. Failure and stable points are then compared to the rock mass strength envelope(s) of Hawkesbury Sandstone derived using the Hoek-Brown criterion and spalling criteria. The Hoek-Brown rock mass strength envelope differentiates between the ‘failed’ and ‘stable’ zones remarkably well.INTRODUCTIONStress induced failures of rock masses are fortunately rare in civil tunnelling. However, when they occur they provide an opportunity to calibrate an assumed rock mass strength criterion. This paper compares an estimate of rock mass strength for the Hawkesbury Sandstone with the following cases where stress induced failure occurred in tunnels excavated within Hawkesbury Sandstone.• Cataract & Devines Tunnels of the Upper Canal (Upper Nepean Scheme)• Malabar Outfall Tunnel• Sydney liquefied petroleum gas (LPG) Storage Cavern• Northside Storage Tunnel• Cross City Tunnel• Lane Cove TunnelTwo-dimensional finite element modelling is used to assess the likely magnitudes of the stresses present at the time of the failures. The principal stresses are then compared to the assessed rock mass strength envelope(s) of Hawkesbury Sandstone derived using the 2002 Hoek-Brown criterion (Hoek et al., 2002) and the spalling criterion suggested by Diederichs (2007)."

Jan 1, 2015

By Zhiqiang Wang

This paper mainly focuses on the method of ?three-zone? definition (a caving zone, a fissure zone and a curve subsidence zone) for full height cutting in a thick seam. Based on criteria of a caving zone and a water conducting zone, as well as existing research achievements, it is believed that there exists great error for calculation of height of the ?three-zone? area using cutting height and the coefficient of bulk increase. Dynamic factors should be considered, so, based on the theory of key rock strata and combining this with several other factors, such as mining area, this paper presents a new method to determine the overburden ?three-zone? definition. The results are as follows: (1) geometric models of a working face and key stratum are established through the rock displacement angle, with consideration of the influence of mining on the key stratum (the range of key stratum influenced by mining is enlarged as the mining area increases); (2) because there is always a cavity below the key stratum of the thick coal seam with full seam cutting, and the key stratum gradually fracture with face advancing, based on the geometric dimension of strata, the maximum fracturing interval expression has been presented, including the working face advancing range. This can theoretically lead to the location of the key stratum influenced by mining, and its stability before mining, helps to confirm which zone the key stratum and following-up strata belong to, using the criteria of sliding instability or deformation instability; (3) the new method of ?three-zone? definition which is based on the theory of key rock strata is first proposed for full height cutting in thick seam. Finally, combined with practical engineering, and comparing with field data, it is believed that the proposed method is more objective than existing methods.

Aug 1, 2013

By G. H. Long, D. H. Magnusson

THE DEFINITION of the continental margin, as considered in this paper, is in the broad sense: " ... those provinces of the continents and of the oceans which are associated with the boundary between these two first-order features of the earth" (Heezen et aL, 1959, p. 17). The provinces in the area under con-sideration are: the Continental Shelf, the Continental Slope and the Continental Rise. The Continental Shelf extends from the shoreline to the shelf break, which lies at approximately the 200-meter isobath through-out the region (except north of the Grand Banks, where the break may be defined more properly by the 400-meter isobath). The Continental Slope and Rise occur between the shelf break and the 4,000-meter isobath. (The last figure was somewhat arbitrarily selected for the purpose of this paper.) The Atlantic Continental Margin as thus defined extends along the eastern coast of Canada from the International Boundary in the Gulf of Maine northward to approximately the 60°N latitude off the coast of Labrador. The area of study amounts to at }east 500,000 square miles -an area roughly equivalent to 13 per cent of Canada's total land surface.

Jan 1, 1970

By E. Quaquero

This article reports on the current state of an ongoing research project which is aimed at implementing intelligent models for hardly predictable hazard scenarios identification in construction sites. As past evidences showed that no programmatic action can deal with the unpredictable nature of many risk dynamics, we tried to survey on how the current approach for safety management in the construction industry could be improved. In our previous research the use of Bayesian networks elicited from subjective knowledge were preliminarily tested. Those networks might be meant as a reliable knowledge map about accident dynamics and they showed that a relevant ratio of occurrences fall in ?hardly predictable hazards? class, which cannot be warded off by programmatic safety measures. This paper reports the second outcome of our research project, which focused on the development of first elementary fragments, regarding the occurrence of a possible ?hardly predictable scenario?. Instead of experts? contributions (who, over their carrier, seldom incurred in accidents), we used ?legal cases? as an accurate source of information. They suggested which categories of ?hidden hazard scenarios? are more likely to happen. We found that the most frequent hidden hazard scenarios are linked to operator?s negligence and abnormal behavior, e.g. irregular removal of scaffolding?s components, unprotected openings, improper use of PPE, etc. Every pattern determined by legal cases has been formalized by a fragment (i.e. elementary network) of the overall Bayesian network. Finally, all the elementary networks were integrated into a comprehensive intelligent tool for realtime hardly predictable hazards prevention. The final setup, asked for interfacing these intelligent models to a low-level sensor network and used to feed them with inputs about the current state of the context, is discussed too.

Aug 1, 2013

By Robert D. McKellar, Luke Frawley, Okrasa. Richard

"The resource industries in Canada are facing increasing global competition and stringent environmental regulations. This has made it essential for companies to lower operating costs wherever possible. Electrical energy rep-resents one variable cost that may be better managed and utilized, providing the user with lower operating costs, improved productivity and better yields.The utility industry is also facing changes in the way it must do business. Utilities in North America are facing the prospect of deregulation that will eliminate the monopoly they have traditionally held. This will force them to strive for lower operating costs, to maintain a competitive position and to improve customer ser-vice so as to maintain their customer base.Ontario Hydro has been working with industry for several years. Many opportunities for cost savings have been identified involving energy efficiency, process improvements and the use of new electro technologies. One useful service that the utility can offer industry is to increase the awareness of potential opportunities suited to their operations. This paper will provide an overview of some of the projects that have been implemented and those that are presently being evaluated. An electronic data-base of electro technology applications that is under development will also be described."

Jan 1, 1996

By Claude Hubert, Robert Sansfaçon

"The Malartic gold camp includes the Malartic Gold Fields, Barnat, East-Malartic, Canadian Malartic and Sladen mines. From 1935 to 1984, these mines have yielded 212 403 kg of gold. They occur within a 900 m wide belt of highly sheared, dislocated and faulted volcanic and sedimentary rocks (Piché and part of the Pontiac groups) herein named the Malartic Tectonic Znne (MTZ). The zone trends WNW-ESE and separates two lithotectonic sedimentary domains, the Cadillac to the north and the Pontiac to the south. The sedimentary domains are characterized by their coherent fold generations consisting of open to tight reclined and recumbent F1 folds that have been refolded into series of asymmetric upright F2 folds. A flat-lying schistosity (S1 ) and a vertical pressure-solution cleavage (S2) are ubiquitous throughout. Discrete sets of brittle and brittleductile faults are synchronous and parallel to each of these two fabrics.The MTZ trends N320° in the northwestern sector of the town of Malartie, changing to N2800 at its easternmost extremity. The Malartie and Sladen faults constitute its northern and southern boundaries respectively. These two faults also bound another set of faults oriented N305°. Throughout the MTZ, the faults at N280° and N320° and those at N305° outline a series of anastomosed motifs that constitute the principal structural feature of the Malartic district. Locally, a fourth set of minor faults at N065° combines with the other three prominent sets. All these faults have disrupted the gold-bearing volcanic, sedimentary and intrusive rocks encountered throughout the MTZ.The MTZ comprises numerous lozenge-shaped blocks of komatiites and basalts or greywackes and black shales which are cut by disjointed dikes, sills and small intrusions of felsic and mafic rocks. The latter includes gabbro, diorite, lamprophyre, monzonite and pegmatite. They frequently fill conjugate sets of fractures. In some areas, they are clustered into coalescent intrusions. The present morphology of these intrusive bodies( cube, chocolate-tablet boudin, parallel epiped and cigar) is not representative of their primary forms but the result of late shearing and faulting indicative of a major tectonic event subsequent to their emplacement. The intrusions were injected during a brittle stage of deformation related to the F1 folding but prior to the development of the F2 folds and subsequent tearing and shearing by late brittle and brittle-ductile faults . The ultramafic and mafic rocks are intensely altered to serpentine, tremolite, actinolite, carbonate, biotite, hematite and pyrite according to the nature of their proto/it h. In the vicinity of the MTZ, all lithologies exhibit mineral assemblages indicative of the upper greenschist or lower amphibolite facies of metamorphism.The structural evolution of the MTZ involved superimposed folding, shearing, transposition, mylonitization, brittle and brittle-ductile faulting. Each lenticular motif results from the combined effect of conjugate sets of shear zones that outline lozenge-shaped blocks where strain markers indicate different strain states from cores to margins. Bedding in ultramafic flows and/or sedimentary rocks is either NW-SE or NE-SW within the blocks but, in the vicinity of the Malartie and S laden faults, it has been rotated to become subparallel to the faults.Ore shoots are most commonly associated with altered and deformed bodies of diorite and monzonite, or some mafic and ultramafic schists and, at the Canadian Malartic, Sladen and East Malartic mines, with metasedimentary rocks. The shoots occur in close proximity to the various faults of the MTZ but the gold itself is intimately associated with pyrite, biotite and carbonate in halos bordering fractures crisscrossing the different host rocks. The density of fractures and the width of their altered zones have been significant parameters in the production of economic ore shoots. Grains of gold are visible in some veins of quartz a"

Jan 1, 1990

By A. Elsayed

Lightweight metals such as magnesium show potential in replacing aluminum alloy castings for engine cradles, cylinder heads and transmission cases. Unfortunately, magnesium alloys are susceptible to entrapping oxides and other impurities during casting that hinder strength and ductility. The current study examined various filter sizes and configurations with the aim of improving the mechanical properties of permanent mould cast AZ91E. The unfiltered casting had a yield strength, tensile strength and ductility of 93.3 MPa, 153.3 MPa and 2.2 % respectively and increased to 96.5 MPa, 167.0 MPa and 3.1 % with the use of a fine mesh filter within the well of the mould. The increased strength and ductility was likely due to the filtered castings containing fewer inclusions on their fracture surfaces as compared to the unfiltered castings.

Jan 1, 2011

By M. L. F. Paullo, S. Cristian Mejia, D. Roehl

"Rock fracture simulation most often presents non-linear behaviour due to loss of material integrity and strain concentration in the fracture zone. These strains generate local instabilities that propagate to the global system of equilibrium equations, generating convergence problems of the numerical solution. Often, in such cases, analyses in the post-critical regime are unfeasible. To overcome the numerical difficulties associated with problems of stiffness loss in the post-critical regime control methods, also called continuation methods, are employed. Among them are the arc-length method, the energy control method and the indirect displacement control method. These methods are employed in conjunction with a Newton- Raphson scheme for the solution of non-linear systems of equations. However, depending on the system instability, convergence in not guaranteed even with very small increments. In the present work these control techniques are investigated in combination with cohesive elements to simulate rock fracture. The constitutive model employed with the cohesive elements represents stiffness degradation through a damage law, which leads to serious convergence difficulties as reported in the literature. Here the continuation methods mentioned are applied to a Mode I rock fracture problem and to hydraulic fracture simulations. The effectiveness of the different continuation methods is compared.INTRODUCTIONThe process of rock fracture induced by the fluid pressure is called hydraulic fracturing. The propagation of a hydraulic fracture is a complex process, which is basically defined by the mechanical deformation of the rock, the fluid flow within the fracture and the fracture propagation itself (Mokryakov, 2011). In the works of Bendezu et al. (2013), Chen (2012) and Carrier et al. (2012), vertical hydraulic fracture propagation is modeled by cohesive elements with traction-separation law. The softening behavior of rock in post-critical regime is demonstrated by experimental testing and is characterized mainly by high strains and low stresses (Crowder and Bawden, 2004). This nonlinear behaviour can arise due to material nonlinearity, such as micro-cracking and damage, leading to softening behaviour (Chandrakant, S.D., 2012). The cohesive fracture model considers in its formulation the softening behaviour that most rocks present in post-critical regime with propagation criteria."

Jan 1, 2015

By J. S. Stewart

THE Mackenzie River Valley proper extends from Great Slave lake to the Arctic ocean (see map, Figure 1). From Fort Providence, near Great Slave lake, to Aklavik, near the Arctic coast, the distance by river is 1,000 miles. This will give some idea of the extent of the region. Throughout the length of the river valley, the Precambrian complex rocks are overlain by unaltered sedimentary rocks several thousand feet in thickness. These sediments are dominantly marine and Palaeozoic in age. In places, the Palaeozoic strata are overlain unconformable by Cretaceous an Tertiary sediments. The strata have been folded and, in general, the inclination of the beds to the horizontal is comparatively gentle. Here, then, we have the essentials for potential oil fields covering an area over 1,000 miles in length. This is probably the largest comparatively unexplored potential petroleum region in North America, and surface evidences of oil in the form of seepages occur in several places. Many of these seeps were known to the early explorers, and the first Geological Survey report on the Mackenzie River region, containing the results of field work carried out by R. G. McConnell in 1887-88, noted the petroliferous character of the Devonian strata and the indications of petroleum(l). This region is, however, handicapped by distance from markets and sources of supply of materials; by lack of modern transport facilities; by short season for river transport, and mountainous country separating the valley from the Pacific seaboard; and by the long winter season with weather that makes outdoor work difficult. These factors have tended to discourage the enthusiasm of would-be promoters, and so development in this region has been slow In 1920, a test well drilled about fifty miles northwest of Fort Norman discovered oil in commercial quantity, and three additional wells proved a small area to be productive.

Jan 1, 1944

By R. Al-Hent, M. Aissa, J. Asfahani

"This paper presents regional radiometric gamma-ray spectrometry maps of Syria for total radioactivity (Ur) and surficial concentrations of equivalent uranium (eU). The maps were created by merging airborne and ground-based gamma-ray spectrometric survey datasets. On the regional radiometric eU map, eU anomalies are closely related to either phosphate and/or glauconite deposits. The Ur and eU maps delineate the boundaries of three phosphate deposits, close to the Palmyrides ridge, in the northern part of the Coastal Range and Syrian Desert. Scattered occurrences of uranium mineralization in other phosphate formations are attributed to secondary chemical and physical processes, rather than primary accumulation.RÉSUMÉ Cet article presente des cartes regionales radiometriques de spectrometrie gamma de la Syrie pour la radioactivite totale (Ur) et les concentrations en surface de l’equivalent en uranium (eU). Les cartes ont ete creees en combinant des ensembles de donnees, aeroportees et au sol, de releves de spectrometrie gamma. Sur la carte regionale radiometrique eU, les anomalies eU sont etroitement reliees aux gisements de phosphate et(ou) de glauconite. Les cartes Ur et eU delimitent les limites de trois gisements de phosphate, a proximite de la crete des Palmyrides, dans la partie nord de la chaine cotiere et du desert de Syrie. Des dispersions de mineralisation d’uranium dans d’autres formations de phosphate sont attribuees a des procedes chimiques et physiques secondaires, plutot qu’a une accumulation primaire."

Jan 1, 2016

By J. L. Feng, F. Zhang, S. K. Hu

"Cracking is one of the most serious damages in tunnel linings, which is often observed by in-situ inspection to tunnel engineering. It is difficult to better characterise for the deformations from continua to discontinua by the traditional continuum mechanics due to emerging of crack initiation, crack propagation, and coalescence, at several scales. In this paper, the process of failure that was from micro damage to macro crack in concrete tunnel linings under experimental load conditions, was quantitatively simulated by the combined finite-discrete element method (FDEM). Comparison of the simulating results with that obtained by the full-scale test of concrete lining under different loading conditions in the literature was respectively good agreed and shows that such FDEM technique is appropriate to model the continuousdiscontinuous problems. The present study indicates that the FDEM technique could be benefit to quantitatively evaluate the stability and damage level of tunnel lining system. INTRODUCTIONMost damage to tunnel linings is caused during the construction phase, which can emerge in a form of single macro cracks or even large-scale spalling. The cause of such damage is mostly the occurrence of, either impermissibly large contact stresses resulting from high thrust loads combined with production and installation tolerances in the segments resulting in a geometrical lack of fit (Maidl et al., 2012; Transportation Research Board, Basic Research and Emerging Technologies Related to Concrete Committee, 2006), or unallowable tensile/shear stresses appearing in the tunnel linings under complicated loading conditions (Ansell, 2010). Such a macro failure phenomenon may also be regarded to as a result of growth, coalescence, initiation of microcracks in tunnel linings due to the complicated loading action, and even potentially lead to an instability or collapse of the local or entire tunnel system. Much work has been devoted to investigate for the characters of micro and macro cracks, the influence factors of damage patterns, the settlement of a tunnel, the width, length and density of lining cracks, especially from classifiedly and qualitatively (Wang, 2010; Huang et al., 2013). However, the safety evaluation of tunnel is definitely required to not only inspect in situ, but further also quantify computing and analyzing for tunnel lining systems, so as to provide a global viewpoint of process of the tunnel deformation, which aims to help for subsequent decisions, e.g. controlling traffic flow or immediately repairing task. Additionally, the design of lining thickness and its structural analysis that is mostly determined by previous experience and similar construction examples is also needed to be improved."

Jan 1, 2015

"Conveyed coal flows have been diverted on the basis of real time ash analysis since the 1980s. Many coarse particle separation methods are available through screens, jigs, heavy media separation, particle sorters, to name a few, however bulk diversion requires a representative, continuous analysis to ensure diversion decisions can be made with confidence. Sensors also need to be able to provide measurements at useful time increments so that small tonnages can be diverted for maximum selectivity. Particle separation typically requires high capital costs and there are limitations either in throughput tonnage or particle size or both. Few techniques are able to provide robust and representative analysis of conveyed flows in a useful time basis. Prompt Gamma Neutron Activation Analysis provides multi-elemental analysis of conveyed bulk materials and has been proven in the minerals industry since 2003. This paper outlines the success of this technology in minerals applications in iron ore, phosphate rock and most recently in copper-gold ores, including its use in bulk diversion.INTRODUCTION Naturally occurring quality variability, or heterogeneity, in mineral deposits enables separation and recovery of the valuable components through mining and processing operations. There are distinct advantages in processing the minimum quantity of material to achieve the highest possible yield. Unfortunately, declining ore grades has resulted in larger scale operations and a subsequent loss in selectivity for mining operations. As limits are approached on the practical size of equipment, there is more motivation to investigate alternative solutions. Mining companies are subject to increasing social resistance to growing waste disposal requirements in addition to higher energy and transport costs. Major savings are available by reducing the quantities of material processed where pre-concentration can be effectively applied at early stages in the process. One of the simplest ways to pre-concentrate is to measure the bulk material and reject waste soon after mining so that minimal expense is incurred and that only higher quality material is sent to processing operations. This bulk sorting can occur within the mining operations and has major benefits through energy and other consumables savings. This paper discusses the application of real time analysis technologies suitable for bulk sorting within the minerals industry. Technology that has proven representative for conveyed material bulk analysis and its successful applications to date is explained. Analysis using a sensing technique is only one component of a successful bulk sorting process; the importance of effective diversion systems and a bulk sorting strategy are also discussed. The bulk sorting stage may be one component of a system that could include additional downstream technologies such as particle based sorting systems on a diverted stream."

Jan 1, 2018

By W. K. Smith, V. P. Krueger, D. C. Mulder

"AbstractThis paper describes the geological procedures used to evaluate two mineable high-volatile C bituminous coal seams at Coal Valley , located in the outer foothills belt of the Rocky Mountain Eastern Slopes in west-central Alberta. Lexco Testing Ltd., the exploration arm of Luscos: Ltd., owns and operates an all -weather geophysical logging system which provides gamma, focused density , single-point resistance and caliper logs in a single pass. A mathematical analysis for a theoretical interpretation of the single-point resistance log confirms empirical research that bed boundaries are located at a point 10% from the bottom of the curve. A unique and efficient triple-tube, wireline rotary coring system cuts an undisturbed 0.076m- diameter core in a plastic liner at recoveries exceeding 90% . Although only 10% of the total footage is cored, it provides vital analytical and geotechnical data, and, when integrated with the geophysical logs, improves the quality and extends the usefulness of interpreting both sets of data. All data are programmed to produce computerized structure contour, isopach, isoratio and isoquality maps, and volume calculations.General IntroductionTHE COAL VALLEY AREA is located in the outer foothills belt of the Rocky Mountain Eastern Slopes, 60 miles (96 km) by road southwest of Edson, Alberta. Luscar Ltd. holds leases which total 49,000 acres (19,830 ha) , of which 18,300 acres (7,410 ha) have been assigned to the Coal Valley mine area (Fig. 1 ) . There are two Paleocene high-volatile C bituminous coal seams initially developed for mining within a total stratigraphic interval of 750 feet (230 m ) (Fig. 2 ). These seams strike generally NW, and in the undisturbed areas generally dip westerly from 10 to 30 degrees."

Jan 1, 1977

By M. Hozayen, Q. Ni, E. S. Radwan, P. Nawrocki, A. Jebbouri

"A major geomechanical study was conducted for one of the UAE onshore oil fields with the purpose of studying reservoir rock properties and stress distribution, based on which a 3D coupled reservoir geomechanical model was built. This model was later used for wellbore stability analysis and for analyzing the effect of fractures on future reservoir production performance, including fracture deformation and permeability evolution occurring due to reservoir depletion and resulting changes in local stress field. The subject of this study was a complex fractured Upper Cretaceous carbonate reservoir characterized by high degree of heterogeneity, both vertically and laterally. Wellbore instability related drilling problems were encountered while drilling the wells in this field. The problems were mainly in drilling the horizontal wells, including breakouts and mud losses. Experimental results of laboratory tests used in this study are summarized in Part I of this paper whereas wellbore stability analysis and formulation of a3D geomechanical model that was built for that purpose is summarized herein.A 3D geomechanical reservoir model was developed, which included natural fractures. The mechanical properties of the reservoir rock, such as Young’s modulus, Poisson’s ratio, UCS, friction angle and tensile strength were populated based on the correlations established in Part I of this paper and the developed model was then used to simulate the 3D mechanical-property distribution and the evolution of the in situ stresses in the field due to depletion from 1983 to present-day. Based on the full field model, mud weight cubes were developed to predict the safe mud weight windows in different drilling directions. In addition, well stability prediction for two planned wells was performed using a 3D near-borehole model. Firstly, the computed stress state and mechanical properties simulated in the full field model were extracted along the well trajectory of an existing horizontal well which was drilled recently and then, a3D near-borehole model was constructed along the well trajectory. The wellbore stability analysis along the well trajectory, including stress state, strain distribution and displacements, was performed to identify the instability events along the well trajectory. It has been seen that the presence of natural fractures is closely related to the recorded borehole instability incidents. The computed plastic strains which indicate the wellbore failure were consistent with the recorded wellbore instability events in the FMI image logs, what provide further verification of the developed model. Then, this 3D near-borehole model was applied to two planned horizontal wells and the wellbore stability analysis for the two wells was carried out.The results showed that drilling vertically in the reservoir is safer than drilling horizontally. However, the drilling mud weight window in the vertical direction is narrow, being as narrow as 18.7 pcf or 0.299 sg locally. Drilling horizontally is less stable towards the maximum far field stress direction than towards the minimum far field stress direction. The mud weight cubes were used to identify the optimal well placement and well trajectory. For planned well trajectories, this technology can also be used to determine the optimal mud weight."

Jan 1, 2015

By Ho-Sung Yoon, Jyothi Rajesh Kumar, Jin-Young Lee

"Global population is a key factor in future energy requirements, especially considering the important elements of global energy resources, electricity production, the accessibility/non-accessibility of electricity, greenhouse gas emissions and the states of nuclear reactors. Everyday human requirements depend on industrial products, and industries need a considerable amount of electricity to run. Nuclear fuel is inexpensive and bolsters industrial growth. As uranium reserves are being consumed rapidly, an alternative source of energy in the nuclear industry is thorium. Here, primary energy supplies by various sources from 1993 to 2011 as well as estimates of future needs to 2020 are discussed. This study finds that primary energy sources are mainly fossil fuels, renewables sources, and nuclear and hydro energy. In addition, growth depends on increases mainly in renewable sources.Recovery of thorium from its ores by using hydrometallurgical routes were described and discussed. The final part of this paper was presented a case study of the thorium extraction from Korean monazite ore leach liquors by using Prieme JM-T diluted in A150 diluent as an extractant system. And possible separation of the thorium from rare earths (REs) and base metals were calculated by measuring of separation factors and finally, the recovery of thorium from loaded organic of Prieme JM-T was established.THORIUM IS FUTURE NUCLEAR FUEL?Global energy consumption is increasing everyday with the high population growth, high industrialization of numerous countries and the higher level of good and services consumption that follows it. If we look at specific sectors of the economy, oil consumption grew by 0.8 million barrels per day, globally, whereas the increase was 0.4 % for natural gas and coal 1.8 % for nuclear power and just under 2.0 % for hydroelectric power (Asheley 2009). Use of renewable sources of energy for power generation and transportation increased by 3% in 2014 (BP 2015)). Thus alternative source of energy must be identified and developed to meet this increasing demand. Thorium is a potential one for the nuclear industry."

Jan 1, 2016

By Ausenco Engineering Canada

"This paper demonstrates the selection of grinding circuit technology for a number of recent projects including discussion of the key drivers and the role of energy efficiency. Decreasing head grades combined with a strong and sustained increase in operating costs has forced miners to examine increased project size, increased equipment capacity and efficiency improvements in order to reduce their unit operating costs and improve overall project economics. Comminution energy consumption, safety and capital cost considerations play a critical role in the success of projects. This paper presents some key guidelines for a successful and cost effective comminution circuit design and includes a case study on three projects, outlining the issues and the drivers which led to the ultimate circuit selection and the critical role that energy efficiency played.INTRODUCTIONComminution circuits for minerals processing are selected based on their suitability and efficiency in reducing run-of-mine ore to the desired feed size for the downstream process. The input material (ore) properties and downstream process requirements are the key determinants and there are standard approaches for each circumstance.The minerals processing industry has been a fast adaptor of efficiency improvements based on increasing capacity of equipment (e.g. trucks, crushers, mills, pumps) but less successful in adapting radically new technologies that disrupt incumbent flowsheets or processes.The installed power of grinding mills has increased linearly over the past 25 years (Meka & Lane, 2010) and pumps and classification equipment have kept pace. The autogenous grinding (AG) and semiautogenous grinding (SAG) mills displaced stage crushing as a dominant method of coarse rock breakage in many applications causing crusher manufactures to increase the capacity of cone crushers to meet the competitive demand.Examples of new comminution technology in the 20th and 21st centuries are the development and adoption of cyclone classification in the 1940s (Newtech, 2016), AG milling in the late 1950s, vertical grinding mills in the 1980s, high pressure grinding rolls (HPGRs) also in the 1980s and ultrafine milling technology in the 1990s (Meka & Lane, 2010)."

Jan 1, 2016

By A. Ignatieff

"Excavation, the principal mining process, 'which hitherto has been based largely on the intuition and logic of mining men, is increasingly receiving the attention of engineers and scientists versed in rock mechanics. The paper intro-duce the principles of this science in simplified form, directed both to underground and open-pit mining. Reference is made to the large annual tonnage from ore and rock excavations, which in 1967 were responsible for 250 million tons of mineral production in Canada.The urge to transform excavation into a continuous instead of an interrupted process is discussed with references to the various types of energies employed or proposed in rock breakage or excavation. Due to the rapid decay of applied energy in the discontinuous and heterogeneous rock environment, large confined blasts proposed for in-situ mining do not give much expectation of success as yet. Raises and ventilating shafts are already bored in reasonably hard rock. Tunnelling machines will be used for drifting and cross-cutting in the future, but continuous mining machines of the cuttmg and shearing type are not 'around the corner' for stoping typical orebodies. On the other hand, bed mining, particularly of coal, has led the way in continuous mining, and Remotely Operated Long-wall Face (ROLF) experiments are progressing in an encouraging way. Some reflections on the mining environment in relation to the human element are made."

Jan 1, 1970

By Antonio Segatori, Bjørn Holmedal, Kai Zhang, Trond Aukrust, Knut Marthinsen

"The visual appearance and mechanical properties of aluminium alloy extrusions are strongly dependent on the microstructure and texture of the extruded profiles, where the desired microstructure and texture may depend on the specific applications. In the present work, the evolution of deformation, as well as recrystallization textures during extrusion of AA6xxx aluminium alloys, have been experimentally and numerically investigated. Extrusion trials were performed in a laboratory extrusion set-up, which enabled immediate water-quenching of the profiles at the exit of the die, and thus the possibility to capture the deformation texture prior to post-extrusion recrystallization. The textures and their through-thickness variations were experimentally measured by the electron back-scatter diffraction technique (EBSD, and the deformation textures numerically modelled by coupling FEM flow simulations and crystal plasticity (CP) simulations. Different CP models as well as different choices of model parameters were employed and evaluated for texture predictions. With an appropriate choice of crystal plasticity model and model parameters, the deformation texture can mainly be predicted, although the accurate intensities are hard to reproduce. The corresponding recrystallization textures, either generated through spontaneous recrystallization of the extruded profiles or through post-extrusion annealing, are far more challenging to reproduce with available recrystallization models.INTRODUCTION Extrusion is a widely applied thermal-mechanical process to produce aluminium profiles. The properties of the profiles, for example mechanical, fatigue, fracture, corrosion as well surface appearance, are strongly dependent on the underlying microstructure and texture, and the requirements with respect to these aspects may vary with applications (Ralston et al., 2010; Dumoulin et al., 2012; Donati et al., 2013). Moreover, it is often a challenge to produce extrusions with a consistent and homogenous grain structure and texture along as well as through the cross section of the profiles. It is thus vital to understand and be able to predict (model) how different microstructures and textures are formed and how they evolve during and after extrusion, as basis for controlling the final appearance and properties of extruded profiles."

Jan 1, 2018

By A. Desbiens, R. del Villar

"This two-part paper summarizes the design and implementation of a distributed PIbased control strategy installed at the B grinding circuit, at the Kidd Creek Division of Falconbridge Ltd. Part I details the design of the control strategy using a grinding circuit dynamic simulator (DYNAFRAG). The first step consisted of sampling campaigns and data processing to calibrate DYNAFRAG. Then, several control alternatives were designed and tested with the simulator. The main feature of these strategies is their ability to regulate or keep within an upper and lower limit five output variables (circulating load, rod mill density, cyclone feed and overflow densities and pump box level) with only three manipulated variables (rod mill water, pump box water and rod mill tonnage). By simulation on DYNAFRAG, it was possible to discriminate among several control structures. The preferred control strategy uses a saturation algorithm, which allows the adequate regulation of two measured variables with only one actuator. Controllers located in interacting loops are appropriately tuned, taking into account the existing process coupling. Part II will present the implementation of the selected control strategy.IntroductionSteady state simulators are used to predict the stationary state of a given process under specific operating conditions. Tradi - tionally, steady state simulation has been applied for process flowsheet design, for evaluating process modification benefits or for determining key operating parameters in process operation optimization. Dynamic simulators add a new dimension to process simulation since they allow the prediction of the process transient behaviour, resulting from the application of a different set of operating conditions and/or from natural disturbances or equipment failure. Dynamic simulators can also be used for the training of new operators or for the design of control strategies."

Jan 1, 1997