Search Documents

By Ting Lu, Gerard Laman

"This document compares the systems of coal classification described under ASTM standards used in Canada to GB standards used in China. A preliminary connection of metallurgical coal classes was set up between the two classifications. In GB classification system, there are nine metallurgical coal groups, namely PS, SM, JM, FM, ½ ZN, RN, 1/3 JM, and QM used in coal blending for coke production. PS coal is almost equivalent to the Low Volatile Bituminous coal; SM, JM, and FM coal groups fall into Low to Medium Volatile Bituminous range; ½ ZN, RN, 1/3 JM, and QM are equivalent to bituminous coal with medium to high volatile matters; QF contains higher volatile bituminous coal compared with High Volatile Bituminous coal. The caking properties commonly used in respective country are also compared in this document. These properties include free swelling index (FSI) and maximum fluidity used in Canada, as well as caking index (GR.I.), and the maximum plastic layer thickness (Y) mainly employed in China. It has been observed that the log of the maximum fluidity has a stronger correlation with the caking index than the Y values. Metallurgical coal processing strategy and typical coking coal product qualities are briefly discussed in the last section of this paper. Currently there is a trend to use heavy medium cyclone in both countries. In Canada the conventional two-product cyclone technology is the preferred practice; whereas in China the three-product heavy medium cyclone arrangement is widely used.INTRODUCTION Coal can be simply classified by applications into two categories: i) thermal coal used to provide heat energy in combustion, and ii) metallurgical coal which is converted to coke, in a carbonization process, and used mainly in the iron and steel industry. Metallurgical coal contains even higher heating values than thermal coal. In addition, it presents unique plastic properties during carbonization which in turn produces a porous solid, high in carbon referred to as coke. Coke is one of the most important raw materials in the iron and steel industry."

Jan 1, 2012

By Monique Pharand, Jeet Basi, Simon Hille

"High quality activated carbon is essential in the recovery of gold in Carbon-in-Leach (CIL), Carbon-in-Pulp (CIP), and Carbon-in-Column (CIC) circuits. Goldcorp’s Campbell complex at Red Lake Gold Mines (RLGM) experienced a period of low soluble gold (Au) recoveries during Q3 2013, during which time the processing plant saw higher than typical Au grades in the CIP tails solution stream. A technical review identified that the CIP circuit may be experiencing a carbon-fouling issue. To further understand the degree of fouling, and to troubleshoot the low recovery problem, samples of carbon were collected from the CIP, elution, acid wash, and regeneration circuits, and submitted for characterization test work. This paper summarizes the steps taken to remedy the carbon-fouling problem at RLGM resulting in increased overall Au recovery.Overview of Red Lake Gold MinesRed Lake Gold Mines is located approximately 450 kilometres northeast of Winnipeg, Manitoba, in Ontario’s western boundary region.All mining is carried out through underground operations, utilizing overhand cut and fill, underhand cut and fill, and long-hole mining methods. Ore types include: silica-replaced carbonate veins with free milling gold, siliceous replacement-type mineralization (rich with arsenopyrite) marginal to veins, broad disseminated sulphide mineralization along major shears, and some minor sulphidized chemical sediment-hosted ore. The operation is supported by two milling complexes: Red Lake, and Campbell.Process DescriptionThe Campbell processing plant's main unit operations consist of grinding, gravity concentrating, flotation, autoclaving, leaching, carbon-in-pulp (CIP), carbon elution and reactivation, electro-winning, bullion smelting/refining and cyanide destruction, and concentrate handling. A schematic of the plant flowsheet is shown in the figure below.BackgroundHigh quality activated carbon is essential in the recovery of gold at many CIP/CIL/CIC processing plants. At RLGM, gold-bearing ore is milled and cyanide is added to leach the gold from the solids into solution. The dissolved gold then comes into contact with activated carbon, and adsorbs onto its highly porous surfaces. Gold is then recovered by separating the activated carbon from the main slurry for further refining. As such, the characteristics and quality of the activated carbon have a significant and direct impact on overall gold recovery."

Jan 1, 2016

By K. Delbeke

Within the framework of the EU Existing Substance (93/793/EEC) and REACH regulations EC/1907/2006), the copper industry initiated in 2000 a comprehensive Voluntary Risk Assessment of copper and several copper compounds. The Italian Government's Istituto Superiore di Sanità, reviewed the process and reports on behalf of the European Commission. Copper exposure levels to man and the environment from production of copper anodes and cathodes, copper powders and copper chemicals as well as fabrication and use of semi-fabrication products and down stream user products were collected across Europe. Environmental and human health effects data were obtained from literature as well as novel research programs and used to deduct safe threshold

Jan 1, 2007

By Brad Hewitt, Jeff Belke

"Murrin Murrin Operations has not had a successful beginning. Numerous reliability and operability issues many of which are the result of design decisions have been addressed through mechanical and operational changes and the CCD circuit is no exception. Four design aspects of the CCD circuit that have caused and continue to cause operational problems are:1. the inclusion of solution neutralisation gypsum in the CCD circuit feed which was designed solely for HPAL residue without proper investigation of its impact on the achievable underflow density and resulting wash efficiency;2. the decision to construct the thickener base from thickened solids;3. the lack of redundancy in the overflow, underflow and tailings pipe work; and4. the lack of thickener operational flexibility in the central rake-lift and feedwell dilution system.In November 2002, the lack of operational flexibility in the rake-lift and the feedwell dilution system through mechanical modification as follows:•, CCD1 has a modified rake mechanism that now allows central vertical lift of 600 mm;•, CCD1 has forced dilution using the Outokumpu Turbodil® technology and replacing the E-Duc® technology of Eimco;The decision to install, the installation and the results of the CCD1 rake-lift mechanism and feedwell dilution system are discussed in this paper. The installation was justified on improved operational robustness and an increase in the in the underflow density of 1 per cent (per cent w/w). At approximately the same time process modifications in the solution neutralisation circuit were implemented and these changes altered the rheology of the slurry reporting to CCD1. Since the modifications to CCD1 and the solution neutralisation circuit, the CCD circuit has averaged a 2 per cent improvement in the circuit underflow density.The CCD1 modification was completed on time and mechanically has performed well. From a risk point of view, the central rake-lift and Turbodil®dilution system add a degree of freedom and robustness to CCD1 operation that has extended the range of operational confidence. In this respect, the modification has been a success and is complementary solution neutralisation improvements."

Jan 1, 2005

By J. L. Jambor, J. E. Dutrizac, J. B. O'Reilly

The present-day metallurgical community is quite familiar with the use of jarosites [MFe3(S04)2(0H)6 where M = K, Na, NH4, Ag, 1/2Pb, etc.] as a means of controlling iron, alkalis and sulphate in hydrometallurgical circuits. This modern precipitation technology has found an increasingly widespread application in the zinc industry111 and is gradually also being extended into the hydrometallurgical processing of copper and cobalt121 . The chief advantage of jarosite precipitation is that the iron precipitate settles and filters well, and gives low losses of divalent metals in the washed residue. Although this jarosite precipitation technology was developed only within the past twenty years, man's involvement with jarosites extends back to antiquity, and jarosites have played an important role as a source of silver in several ancient metallurgical centres. In the early days of this century, argentojarosite was an important local source of silver at the Tintic Standard mine, Dividend, Utah, where over 200 000 oz of silver were recovered from highgrade natural jarosite over a three-month period 131 . At the Matagente mine in Peru, pockets of argentiferous plumbojarosite up to 40 m thick were mined and processed by the Indians prior to the arrival of the Spaniards14-51 . In Cyprus there are vast jarosite deposits associated with the ancient mining sitesl51 , but exploitation of these jarosites has been insignificant because of their low silver values. The most extensive mining of silver-bearing jarosite, and certainly the oldest documented instance of such jarosite exploitation, was in the vast pre-Roman workings at Rio Tinto, Spain. This mine, the greatest single miningmetallurgical site currently known from the ancient world and also the oldest site of more or less continuous metal production, has witnessed many metallurgical firsts. Aside from the initial processing of jarositic ores for their silver values, the development of large-scale hydrometallurgy also seems to have occurred at Rio Tinto. As early as 1737, copper was recovered by cementation on scrap iron from the mine waters at Rio Tintol51 . Large-scale heap leaching of calcined ore commenced with the British operations in 1876 and, by 1900, raw pyrite was heap leached to recover associated copper values161 .

Jan 1, 1999

By É. Roberge, S. Makni, G. Gagnon, F. Lavoie, A. Faucher

"Feed particle size is an important variable for the primary grinding mill operation. Several commercial vision systems have proven to successfully measure online many types of ores and are used for automatic control. However, due to limitations associated with segmentation algorithms, these systems fail to provide good measurements when the feed is composed of a specific bimodal particle size distribution: very big rocks and a large amount of fine particles. This is typically the case for crushed iron ore. This paper presents a technique to overcome the limitations of existing vision systems by using 3D cameras and appropriate processing methods. It provides online particle size distribution indicators and bulk volume flow rate measurement. It is designed to be very cost-effective, robust, precise, easy to install and to maintain. The 3D system was validated in two iron ore processing plants and the results clearly show that it can be used to optimize primary grinding mill operation where 2D segmentation vision systems fail.INTRODUCTIONFragmentation measurement using digital image processing has successfully been applied in mining and mineral processing operations. Several maintenance and operating applications are already deployed in the industry: Measurement of rock fragmentation after blasting (Maerz, 1999; Palangio, 1999) (Pragyan, 2012) Truck inventory (Palangio, 2005) Monitoring of crusher mantle wear Automatic control of crushers and SAG mills (Bouajila, 2000) (Bartolacci, 2001)Commercial technologies like WipFrag (Maerz, 1999), VisioRock and others proved to be very efficient to precisely measure the particle size distribution of many types of materials. These products are mainly composed of a camera, a lighting system and an image processing system based on a segmentation algorithm. By controlling adequately the lighting conditions and with periodic maintenance on the segmentation algorithm calibration parameters, it is almost always possible to achieve reliable measurements.However, the segmentation algorithm is not adequate when the particle size distribution contains big rocks and a large amount of fine particles. In this case, the area containing the fine particles is accounted as a big rock while big rocks get segmented as multiple smaller sized particles, leading globally to a wrong measurement. This situation prevails for crushed iron ore and coke, among other materials. Figure 1 shows a picture of a material which is typically very difficult to process through segmentation techniques."

Jan 1, 2015

By B. S. Fee, R. R. Klimpel

"Froth flotation is the most widely used and economic means of concentrating metal sulfide ores such as those containing copper, lead, zinc, nickel, molybdenum, and pyrite. Also recoverable are other metal species that are often associated with sulfide ores such as cobalt, platinum, gold, silver, etc. Most of the initial developments made with the process of froth flotation in the early 20th century were based on the processing of metal sulfide ores. It is the relative technical and economic ease of floating metal sulfide minerals with small amounts of appropriate frothers and sulfur containing (thio) collectors that has been a major economic driving force behind the rapid expansion in the supply of metals such as copper, lead, zinc, and nickel that has occurred in the world's economy in the last 50 years. This author estimates that 1.6 billion tons of sulfide ores are processed each year (1980) in the free world based on the froth flotation process.While there has been a tendency for the quality of metal sulfide ores in any one geographic location to deteriorate over time due to mining intensity, the overall global supply of sulfide minerals is still very large. Thus, the physical supply side of sulfide ore concentrates has not been under strong technology improvement pressure with increasing metal demands. Part of this is due to the ability of capital to consistently move to new geographic locations having suitable grade sulfide ores. In these moves, the actual froth flotation technology used (including collector chemicals) has had to change little. As an illustration of this trend, of the approximately 80,000 metric tons of thio collectors used commercially (1980) in the free world, almost 98% were known and manufactured in some form 25 years ago (1). This is clearly not typical of reagent development in other process related industries. In addition, the industrial scale practice of froth flotation applied to sulfide ores has proceeded since the 1920 s with often little direct (predictive) scientific explanation due to the extreme complexity of the flotation process. Empirical testing has been a mainstay of industrial flotation reagent development and use. Even today there is often strong disagreement between researchers as to the mechanisms of chemical flotation practices that have been performed successfully at an industrial scale for many years."

Jan 1, 1987

By Eric Bain Wasmund, Lance Christodoulou, Julio Jairo Carmona Franco, María Fernanda Castillo, Jose Concha

"A number of technologies are in practice for selectively removing coarse gold from conventional grinding circuits. These circuits are often designed so that the grinding mill output is size classified, with large (or high density) particles being removed before the tails are returned to the mill. Because of the high relative SG of gold, and the fact that some forms of gold such as free gold do not break apart during conventional grinding, coarse gold can accumulate in the circulating load, and eventually be lost.Eriez has developed a flotation cell that uses fluidized water to enhance flotation of coarse particles. More than 40 units have been sold in industrial minerals, and we are now exploring applications for the HydroFloat® in the gold industry.Mineros S.A currently produces approximately 120,000 oz of gold per year by gravity concentrating alluvial gold ore with a mean particle size of 330 microns, followed by further concentration using a Falcon separator. A 400 mm diameter pilot-scale HydroFloat® was added to the tails of the Falcon to test whether additional gold could be captured. Enrichments of 50-600 times and recoveries normally in excess of 95% were achieved. This allowed direct smelting of the gold concentrate. Metallurgical results and operating parameters such as water addition and power will be discussed during the presentation.This result opens the possibility that the HydroFloat® could be used directly in the grinding circuit, for removing coarse gold in the circulating load. This work also shows the possibility that the HydroFloat® can produce a throwaway tail, which will reduce the size of the circulating load stream and the grinding requirements of the circuit."

Jan 1, 2015

By K. Pirapakaran

The Geotechnical Engineering research group at James Cook University has been working closely with all the leading mines in Australia in the area of minefills. They have carried out substantial research and consulting work on the drainage and stress developments within hydraulic fills. The objective of this paper is to summarize their work during the past five years on hydraulic fills. The paper will serve as a one-stop reference, pointing to relevant literature including the authors? own publications, on various issues covering drainage and stress developments within hydraulic fills. More than 15 different hydraulic fills, representing five major mines in Australia, were studied. Their grain size distributions and placement characteristics including permeability, porosity and dry density were studied and comparisons were made with the limited in situ data available in the literature. Stress development within hydraulic fills has been studied to minimize the risk associated with barricades failure. FLAC and FLAC3D were used to model stress developments within the hydraulic fills and were compared against the approximate closed form solutions available in the literature. A laboratory model was developed to study arching effects within the hydraulic fills.

May 1, 2007

By D D. Deacon

A brief description is given of the requirements which No. 4 Shaft has been designed to meet and of the methods by which two-stage winding of rock has been accommodated in a single shaft sunk to a depth of 7,421 ft. This is followed by a consideration of the factors which led to the decision to sink the shaft as rapidly as possible. Introduction T HE No. 4 Shaft of Hartebeest-fontein Gold Mining Company, Ltd., has been sited to serve the deep southern area of the mine, some 1,500 claims in extent, between the elevations of 6,250 and 7,300 ft. below surface. From this area, some two-thirds of the mine production will ultimately be obtained. Above the 6,-250-ft. elevation, an existing shaft hoisting system, situated adjacent to the reduction plant, is of adequate capacity to cater for all ore hoisted to surface for milling. No. 4 Shaft will therefore be required to provide downcast ventilation of 1,000,000 c.f.m., together with surface hoisting facilities for men, material and development rock and underground hoisting

Jan 1, 1965

By Phillip I. Merritt

"IntroductionDuring and since• the war, it has been my privilege to work closely with those in Canada who are responsible for the vital raw materials needed in our co-operative atomic energy programme. The understanding which has developed between our two groups in this all-important enterprise has been a great source of pleasure. We in the United States are aware of the importance of the contribution made by Canada to this project, and we look forward to continuing our mutually advantageous relationship.The impact of World War II, and the decision by Canada, Great Britain, and the United States to join in a programme for the development of atomic weapons, created a sudden and immense demand for uranium minerals. Early in the raw materials programme, it was evident that sufficient raw materials to fulfill war-time atomic weapon requirements could be secured from three sources: the rich pitchblende deposits of the Eldorado , mine at Great Bear lake; the Shinkolobwe mine in the Belgian Congo; and as a by-product of the vanadium industry of the Colorado Plateau in the United States. In the early part of the programme, therefore, our joint efforts were directed toward obtaining immediate maximum production from these localities. The contribution made by Eldorado Mining and Refining (1944), Limited, both in supplying and refining raw materials, was and continues to be of vital importance.In addition, it was also obvious from the first that in this programme, as in any mining enterprise, exploration activities directed•toward the discovery and development of new sources of uranium ore were essential if production were to be maintained over an extended period of time. In order to satisfy obvious security requirements during the war, it was necessary to proceed with this exploration programme, both in Canada and the United States, as secretly as possible. With the end of the war, and the revelation that an atomic weapon had been developed, however, secrecy in exploration was no longer required. The important thing was to get on with a broadened exploration programme."

Jan 1, 1950

By F. Baerhold, S. Mitterecker

"Acid recovery is an important process step in pickling and leaching processes. Pyrohydrolysis in spray roasters and fluidized beds is a well-established technology to recover hydrochloric acid, but the hydrolysis in the liquid phase is more and more considered as an alternative new process route. The characteristic features of these three processes will be discussed along with select industry trends. For example, hydrochloric acid based leaching processes for ilmenite and nickel laterite ores produce far larger volumes of waste acid streams than the steel industry. Scaling-up of the spray roasting technology to the highest possible capacity is necessary in order to become more cost effective. In addition, process routes based on ferric chloride pyrohydrolysis allow the production of super-azeotropic HCl (up to 30 wt.%). Finally, the new ECOmode concept optimizes the operation of both pickling lines and the spray roast acid recovery plant. Long term results from industrial applications show that fuel savings in the spray roaster of 25% are easily achieved without additional process steps. An attractive feature is also to upgrade existing installations to higher plant capacities.INTRODUCTION Pyrohydrolysis is the conversion of metal halides into metal oxides at elevated temperatures in the presence of water vapor. Reaction products are a hydrogen halide gas and a metal oxide. The process was originally developed and introduced into the market by ANDRITZ Ruthner in the 1960’s. It has found wide technical application in the field of acid recovery and oxide production. The introduction of this process has revolutionized pickling technology. The use of hydrochloric acid has strongly increased over the last decades, since pyrohydrolysis is available for the total recovery of waste pickle liquors from mild steel pickling, as illustrated in Figure 1.Chloride media are also used increasingly in the metallurgical industry. Oxide production processes for Mg, Co, Ni, and Al have been installed. Processes using hydrochloric acid are known for the leaching of ores as well as for the re-extraction of metals from organic solvents. In both cases the recycling of HCl is of substantial importance to achieve highly economic processes and to reduce waste."

Jan 1, 2016

By Filip Rochette, Yvan De Busscher

Extraction of minerals can be achieved by a variety of technologies; one of them is ion exchange. There are several ion exchange configurations and mechanical set-ups available, but only one technology will provide more process performance and flexibility compared to the other. The multiple column Continuous Countercurrent Ion Exchange (CCIX) technology provides the highest form of process flexibility with also the highest mineral recovery feasible through ion exchange. In comparison with a fixed bed system, the PuriTech CCIX system offers the benefits of continuous counter-current contact mode. This way the resin capacity is fully exploited leading to reduction in resin inventory and, at the same time, in chemicals and water consumption, and product dilution. For any set of operating conditions the mass transfer zone has a characteristic length (MTZL). The MTZL can be expressed in duration, column length, or volume, but is the measure of the quantity of resin in the system that is doing "work" at any given moment in the process. The objective of continuous ion exchange processing is to eliminate all resin volume from the process equipment that is not within a mass transfer zone. In most commercial ion exchange processes for the recovery of metals, CCIX engineering can eliminate as much as 20 - 80 % of the ion exchange resin inventory. Consumptions of water and chemicals are typically brought down around 40% or more. For each type of resin the selectivity/affinity towards a particular metal depends on the basic process conditions such as pH, concentrations of other competing metals in solution. By changing the pH in the ion exchange process phase, the selectivity of the resin can be changed. By doing this, a split elution, or extraction of metals separately can be achieved and the effect of other competing metals (cross-contamination) can be reduced. For example the DOW resin XUS43578 is commonly used for the recovery of copper or nickel/cobalt separation.

Jan 1, 2016

By Wayne Phillips, Anatalia Silva, Robert Henderson, Tondo. Luis

"Kinross’ Paracatu Mine has 20 years of operational success as one of the lowest grade milloperated gold mines in the world. At year end 2005, Paracatu’s Proven and Probable Reserves were 1.18 billion tonnes at a grade of 0.40 g/t Au, containing a total of 15.2 million ounces of gold.In 2005, the plant processed 17 Mt of ore and produced 180,519 ounces of gold at a cash cost of US$274/oz. An investment of US$470 million has been approved to expand production to 61 Mtpa in 2009 which will extend mine life to 2036. During the period from 2009 to 2013 the project is expected to produce an average annual output of approximately 557,000 ounces of gold at an average cost of sales of approximately $230 per ounce.The soft, friable ore containing readily leachable gold associated with sulphides lends itself to simple processing. The process flowsheet consists of crushing, grinding, gravity recovery, flotation, concentrate leach and carbon adsorption to produce bullion bars. This paper describes the current operation, the deposit’s unique metallurgical features and the future expansion plant that has been designed to optimise recovery of gold.INTRODUCTIONRio Paracatu Mineração (RPM), a wholly owned subsidiary of Kinross Gold Corporation, operates the Paracatu mine. The mine is located in Brazil, 230 km south west of Brasilia in the north west portion of the State of Minas Gerais. The city of Paracatu, which has a population of 83,000 people, is just 2 km south of the mine."

Jan 1, 2007

By S. J. Haynes

"This paper documents the characteristics of the different quartz veins, and their relation to gold, in the turbiditic Meguma domain of eastern Nova Scotia. Eleven different types have been distinguished in the greenschist facies on the basis of form, internal structure, mineralogy, wallrock alteration and crosscutting relationships to each other and to regional structures. Gold is present as rare visible disseminations in host rock slates and in ore-grade, early-formed veins, that pre-date the formation of upright Acadian folds and intrusions of Devonian granitoids. Four vein types pre-date Acadian folding. Five gold-deficient vein types are associated with Acadian folding (syndeformation); whereas two gold-deficient vein types clearly post-date this deformational event: Previously unreported, wall rock alteration is associated with early crosscutting and semiconcordant auriferous veins. In contrast, early stratiform veins are devoid of wallrock alteration. It is suggested that the auriferous vein arrays formed as submarine exhalitive systems over synsedimentary tensional faults and that the Meguma domain may represent the opening of a basin similar to the modernGuaymas rift .IntroductionThe term ""turbidite-hosted gold deposits"" is introduced to distinguish gold deposits contained within a turbiditic sequence of wackes and shales (or their metamorphosed equivalents) from gold deposits in other types of sediments. Usage and justification for the term is similar to ""carbonate-hosted lead-zinc deposits"" or ""volcanogenic massive sulphides"". A range of different characteristics can be present in individual deposits, some of which may be indicative of specific deposit types in the same manner that volcanogenic massive sulphides can be subdivided into ""Cyprus type"", ""Kuroko type"", ""Besshi type"", etc. Historically, gold deposits hosted by turbiditic flysch were an important class of quartz-vein gold mines in the 19th century. They included the goldfields of Victoria, Australia, Otago, New Zealand and Nova Scotia, Canada. Production from most of these fields had ceased by World War II and interest in this type of deposit waned. However, the recent exploration interest in gold has resulted in both re-assessment of the classical mining camps and the discovery that ""turbidite-hosted"" gold deposits are present in many parts of the world.Mapping of the regional geology and gold deposits of the Megumadomain of Nova Scotia was carried out by E.R. Faribault of the Geological Survey of Canada between 1886 and 1939. Faribault produced a comprehensive series of maps and reports for each gold district, a compendium of which was published by Malcolm (1929)."

Jan 1, 1987

By H. C. Horwood

INTRODUCTION THE Argosy Gold Mines, Limited, which joined the ranks of active Ontario gold producers during the summer of 1936, holds a group of 21 claims on Casummit lake, in the Patricia portion, district of Kenora, northwestern Ontario. The Company is developing and mining goldbearing quartz veins that occur in a series of greywackes and slates of probable Keewatin age. The writer made a geological examination of the property and the surrounding area for the Ontario Department of Mines during the early part of the field season of 1936. This paper is a report on the general geology, structure, and ore deposits at the mine and is based almost entirely on data compiled during the examination. HISTORY Mineralization was first discovered on the property in May, 1929, by A. F. Hewitt, who, with J. A. Borthwick, decided that the country had prospecting possibilities and commenced work in April. Mr. Hewitt staked, and with his partner, J. Ziyone, still holds the group of claims lying immediately east of the present Argosy holdings. Mr. Borthwick staked six claims, K.R.L. 9,681 to 9,686, inclusive, adjoining Hewitt's on the west and later added claims K.R.L. 9,733 to 9,740, inclusive, to his holdings. F. Fiskness, who was also prospecting in the region, discoveted No. 1 vein on Borthwick's claims, and with his two partners, L. Parth and H. Jones, staked claims K.R.L. 9,758 to 9,763, inclusive, to the northwest of Borthwick's and Hewitt's ground. In July, 1929, the Casey Mountain Operating Syndicate, which held ground to the northwest, secured an option on Borthwick's claims. The Fiskness-Parth-Jones property was added in January, 1930, to protect the west dip of the veins. During the winter of 1930-31, the veins were explored by diamond drilling, No. 2 for a length ?of 900 feet and a vertical depth of from 51 to. 375 feet? and No. 3 .t~ a slope depth of 175 feet. I~ August, 1.931, after the msrallat10n of a miming plant, the Casey Summit Gold Mmes, limited, was incorporated to take over the property from the Syndicate. The Maple leaf Mines optioned a controlling interest in the stock in August, 1933, and on September 17th, 1934, brought a 50-ton amalgamation mill into production. From early in October to December 27th, 1934, when the mill was closed down, 4,094 tons of ore were treated to yield 887.89 ounces of gold and 87 .26 ounces of silver( ! ).

Jan 1, 1937

By Robert E. McIvor

"The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out.The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, “Circuit Classification System Efficiency” (CSE), is the fraction of “coarse” material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of “fines” or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable target CSE for any given circuit can be estimated, for example, by referring to a plant data base of CSE’s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE.This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.THE FUNCTIONAL PERFORMANCE EQUATIONObservation of the feed and product size distributions going into and discharging from the mill in grinding circuits with low versus high circulating load ratios initially led to the definition of “Circuit Classification System Efficiency” (or CSE, McIvor, 1988a), and subsequently the discovery of the Functional Performance Equation (McIvor, 1988b; McIvor et al, 1992). The CSE is the fraction or percentage of “coarse” (usually in reference to the plus P80) size material inside the mill, versus “fines” or product size material finer than the circuit P80. It can be readily calculated by taking the average of the percentage of said coarse material in the mill feed and mill discharge streams. As this also represents the percentage of the mill energy expended on targeted, coarse size material, it is directly proportional to overall grinding circuit efficiency and production rate. This is all clearly expressed in the Functional Performance Equation for ball milling circuits, for which the derivation has often been presented (e.g. McIvor, 2006)."

Jan 1, 2011

By Chuck Edwards

"Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. Over that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin close out the paper.INTRODUCTIONThe roughly oval Athabasca Basin in northern Saskatchewan occupies nearly one third of the surface area of the Saskatchewan Shield. Its sandstone-like deposits lie unconformably on the older basement. The basin hosts many high-grade unconformity-type uranium deposits(Saskatchewan Energy and Resources, 2010) for which the Athabasca Basin is world famous. Uranium production in the Athabasca Basin has come from four mills. In the order of startup these are Rabbit Lake, Cluff Lake, Key Lake and McClean Lake. General data (AREVA, 2010; Cameco, 2010; Denison 2010) for each mill are shown in Table 1."

Jan 1, 2011

By J. D. T. Steyl, C. A. Biley

"The chemistry of electrolyte systems containing iron remains generally poorly understood despite their prevalence in many natural and industrial processes, particularly in hydrometallurgy. These systems are typically challenging to study and model due to their affinity for complex formation and precipitation even at low pH. Recent developments in the hydrometallurgical processing of nickel laterites at Anglo American have called for a deeper understanding of the fundamental chemistry of the Fe2(SO4)3–FeSO4–H2SO4–H2O system. This paper details the development of an internally consistent, Pitzer ion-interaction model of this system, with explicit recognition of important contact ion pairs (CIPs). The primary application of this model is a thermodynamic framework for the interpretation of kinetic processes occurring during iron(III) reduction with SO2. Adopting a rigorous thermodynamic basis for the system chemistry facilitates the formulation of simple rate expressions that are capable of inherently capturing complex effects. While the iron(III) reduction case study remains the focus of this work, the developments have more universal applications and the thermodynamic speciation model can be extended into other systems containing acidic ferric sulfate.INTRODUCTIONIron is present in nearly all hydrometallurgical refining circuits typically as both a necessary and unwanted impurity and needs to be removed and disposed in a safe and efficient manner. This is generally performed by precipitation to form a range of solids such as hematite, goethite or jarosite. Numerous studies in the open literature have focussed on the removal of iron from refractory gold sulfide ore (Berezowsky & Weir, 1989; Berezowsky et al., 1991) and zinc pressure leaching (Buban, 1999; Ismael, 2003), and PGM matte sulfide circuits (Dutrizac & Monhemius, 1986). Moreover, since ferric iron is a strong oxidizing agent, it has been used extensively as a leaching agent for sulfide minerals (Dreisinger, 2006). Given the outlook of challenging economic conditions, declining ore grades and increasing levels of impurities, effective iron management is going to become increasingly critical to all hydrometallurgical processes.Against this background, and considering the widespread importance of acidic iron sulfate systems throughout natural and industrial processes, it is unexpected that the knowledge of the fundamental solution chemistry of these systems contains such significant gaps, particularly at the conditions typically found in hydrometallurgical applications. Existing literature describing the measurement and modelling of solution speciation in these systems have highlighted their significant chemical complexity (Magini & Caminiti, 1977; Magini, 1979; Lee & Tavlarides, 1985; Stipp, 1990; Papangelakis et al., 1994; Gil et al., 1995; Majzlan & Myneni, 2005; Kormanyos et al., 2008; Yue et al., 2014). Partially responsible for the lack of quantitative speciation measurements is the strong tendency of ferric to hydrolyse at even low pH (Flynn, 1984), complicating the laboratory study of such systems. Moreover, the large number of aqueous species that may co-exist simultaneously makes the study of individual species and the modelling of the numerous interactions between these species extremely difficult (Dry & Bryson, 1988; Stipp, 1990; Majzlan & Myeni, 2005; Kobylin et al., 2007)."

Jan 1, 2016

By Kosuke Hosoda, Shuji Owada, Hiroyuki Tokuichi, Hirobumi Ohta, Chiharu Tokoro, Moto-o Sato, Katsushi Okumura, Hiroto Ogawa, Hideaki Umezawa

The Japanese government enforced the "Small Domestic Appliances (SDAs) Recycling Law" in 2013. The law targets metals such as Ta, Nd, Dy, Co, and W to be recycled. Considerable amounts of these minor rare metals are mounted on printed circuit boards (PCBs) of the SDAs and/or e-scrap (electric and electronic scraps). Although precious metals and copper can be recovered from the e-scrap in non-ferrous metals smelters, most of the minor rare metals report to the slag in these smelters in non-recoverable forms. These metals are often used in particular types of devices, and therefore it is possible to concentrate them by separating such devices before feeding to the smelters. In previous work we developed technology for "Device Separation" to concentrate several minor rare metals, but some problems remained, such as how to remove the PCBs from e-scrap bodies, and how to detach devices from PCBs after their removal from escrap bodies. This paper proposes a two-stage crushing process in which, firstly, PCBs are removed from the e-scrap body with various crushers, and secondly, devices are detached from the PCBs involving the application of elevated temperatures. It was found that in the first stage, crushers with physically flexible rotating media such as chains, which provide high collision probability with the sample and consume relatively low energy, can quite effectively separate the PCBs from the e-scrap bodies non-destructively. In the second stage, heating was found to be remarkably effective in helping to detach mounted devices from PCBs, also non-destructively. This paper will also discuss the detailed mechanism of the heating effect on the detachment of devices from PCBs.

Jan 1, 2014