Search Documents

By Martin Lebeuf

The phenomena occurring in the cathode and at the cathode surface of aluminum electrolysis cells are very important in regards to cathode voltage drop and cathode wear. In the current study, laboratory-scale aluminum electrolysis cell cathodes were analyzed by X-ray microtomography. This technique allows an excellent visualization of the distribution of different substances, if their respective X-ray attenuation coefficients are different enough. In the current case, the important difference in the mean atomic number between cryolitic bath and graphitic carbon results in good contrasts. The volumetric bath penetration profile, porosity and impurities distribution in the cathode were thus obtained. Furthermore, metallic impurities and bath heterogeneities were observed at the cathode surface. Observations were also made with Scanning Electron Microscopy - Energy Dispersive Spectroscopy (SEM-EDS).

Jan 1, 2011

By J. R. Porter, C. Panaou

"A significant effort is expended on preparation of the capital estimate for feasibility studies. The development of the operating cost estimate is usually allocated a significantly smaller budget and less emphasis is placed on ensuring the accuracy of the operating cost. This paper presents a comparison of capital and operating costs of hydrometallurgy processing plants in order to demonstrate the importance that variations in operating costs have on the overall life-of-mine costs. The analysis is supported by a case study on the operating costs of a water treatment plant at an existing Australian hydrometallurgy facility at the feasibility design level. INTRODUCTIONDetermination of the economic validity of a minerals processing project is a critical outcome of a feasibility study. In many cases, the financial results of the feasibility study will determine if the project should proceed to execution. Ensuring that these results are reliable and built upon sound engineering practices allows companies to make informed decisions on resource opportunities and the selected technology.The methodology for developing a capital cost estimate at the feasibility level is well established. Specialist engineering estimators use budget quotations, first principle estimation and rules-of-thumb to develop an estimate with an accuracy of typically -10% to +15%. Cost reporting software packages are used to methodically build up the estimate from design information supplied by the engineering disciplines. Risk analysis and capital expense workshops are carried out to identify potential deficiencies in the estimate. It is widely recognized that in order to successfully produce a feasibility level capital estimate with an appropriate level of accuracy, a rigorous development process is necessary.The development of the operating cost estimate is typically less rigorous than the capital cost estimate. The operating cost is normally derived by the process engineering discipline and rarely are specialist estimators used to support the development. The allocated budget for producing an operating cost is usually smaller and less emphasis is placed on ensuring the accuracy and contingency reflect the most likely operating cost scenario."

Jan 1, 2012

By W. S. Dyer

Considerable attention has been paid in recent years to the fire-clay and silica-sand deposits of the Mattagami and Missinaibi rivers and ? to the lignite occurring in them. The fireclay especially deserves this attention; it is of first-class quality; it appears to be widespread; it is the only fire-clay in central Canada, and part of it lies not more than 20 miles west of Coral rapids, to which point steel will be laid this coming spring by the Temiskaming and Northern Ontario railway. Undoubtedly, these clays will rapidly find a place in industry. The fire-clays and the better grades of silica-sand are Mesozoic in age and have been referred to the Lower Cretaceous or Upper Jurassic. Glacial clays and sands and Palaeozoic shales also occur in the same region, but are of little economic value, and will not be dealt with in this paper. Dr. Robert Bell was perhaps the first to discover the clays, since in the Report of Progress of the Geological Survey of Canada for 1877 and 1878 he reported beds of lignite on Coal brook, a tributary of the Missinaibi river, underlain by sticky clay and overlain by glacial drift. In 1880 E. B. Borron (1) discovered an extensive deposit of white sand and clay on the east bank of the Missinaibi river, five miles below Coal brook, and in 1890 (2) he examined the deposit found by Dr. Bell on Coal brook. He recognized that the underlying clays were quite distinct from the glacial clays of the region, and suggested that they might be used for fire-brick if metallurgical operations were undertaken in the region. Somewhat later, J. M: Bell described a deposit of fire-clay and silica-sand on the Wabiskagami river, another tributary of the Missinaibi.

Jan 1, 1928

By Ian Hattie, Mark R. Wilson, T. Kurtis Kyser, Brian W. Janser

Petrographic, chemical and isotopic compo itions of auriferous and non-auriferous quartz vei ns from the Sta r Lake and Flin Flin-Amisk Lake areas of northern Saskatchewan indicate diver e origins fo r the fluids associated with gold mineralization. In the Sta r Lake area, the metavolcanic , Star Lake pl uton, and heared mafic dikes have retained their original igneous 81 80 values. The 81 80 value of quartz from mi neralized veins vary by I per mi! and range from+I0 to+IJ. The only quartz ample having a 81 80 value outside th is range came from a vein not associated wi th a dike or gold mineralization . Quartz from the Star Lake pluton has identical 8180 value to the qua rtz from mi neralized vei ns which suggests that the vei ns and the pluton are related to imilar proces es. The diffe rence in 81 80 values between mi neralized and barren vein may erve a a potential exploration tool in this area. Because o34S val ues of a limi ted number of amples of pyrite from gold-bearing quartz vei ns at Star Lake correlate directly with gold content. the gold may have been syngenetic with the su lphur and the 834 value may be useful for exploration . 8180 values of co-existing quartz, calcite, and amphibole in the veins from Star Lake indicate that isotopic disequilibrium among the minerals is common, but the val ues also record a high temperature of formation (ea . 500°C) involvi ng a component of magmatic fl uid. TheoD value of hydrou mineral from Star Lake retain their original igneous values but whole rock values are generally much lower, an effect attributed to interaction of the minerals with a late meteoric water. In the Fl in Flin-Amisk Lake area, auriferou and barren quartz veins formed from a mixture of hydrothermal and metamorph ic flu id at lower temperatures (ea . 350°C) than those at Sta r Lake. Becau e there i no apparent correlation between 8180 values of the quartz with gold content or relative age of the vein , nor between the 834S val ues of pyrite and gold content, table isotopes appear limited as an exploration tool in the Fl in FlonAmisk Lake areas.

Jan 1, 1986

By O. Peters, D. Lascelles, R. Caldwell

Ageing tests on a crushed Cu-porphyry ore were conducted to assess the impact of sample oxidation on flotation performance. The objective of the testwork was to simulate ageing of ore that would be blasted through block caving but not milled for possibly several months. Ageing was performed in specially designed columns, using site and deionised water to keep the samples moist over the entire ageing period. Samples from each ageing interval (0, 0.5, 1, 2, 4, and 8 months) were examined for physical and metallurgical changes resulting from the ageing process through chemical analyses, size analyses, and batch flotation tests.

Jan 1, 2009

By Karl J. C. Harries

"4.1. INTRODUCTIONThis chapter, although divided into four parts, deals with only two principal topics. The first briefly describes and discusses some common types of property interests and considerations relating to them and the second deals with entering upon privately owned lands and obtaining the consent to do so.It should be noted that the terms “mining rights” and “mineral rights” are used interchangeably. As so used, they include the right to exploit the minerals and dispose of them for the benefit of the owner/lessee. This is relatively common in common law jurisdictions. In some jurisdictions, the two terms have distinct meanings, with “mining rights” referring to the right to work or exploit the minerals and “mineral rights” referring to the minerals themselves.Finally, it must be mentioned that the comments in the Introduction and §§ 4.2., 4.3. and 4.4. are based primarily upon Ontario law and Ontario’s mining and real property systems of registration. They have been included for illustrative purposes.4.2. LICENCES, CLAIMS, AND LEASESIn most jurisdictions, there are several basic types of interests that can be obtained from the state for mining purposes and that are of interest to the explorationist, as opposed to the operator. Different jurisdictions will have variations of these and possibly some extra ones that will address special purposes or local concerns. In virtually every jurisdiction, privately owned property rights are obtained through negotiation between owner and acquiror.Exploration or prospecting licence. This licence grants to the holder the right to prospect over a large tract of land and the exclusive right to acquire mining claims within that tract for the term of the licence. Such licences are usually negotiated documents requiring a minimum expenditure during the first year (often secured by a deposit or surety bond) and minimum annual expenditures thereafter to continue the licence in force up to its full term. The term will rarely exceed four years. The number of claims permitted to be staked will be limited in some way, possibly as to a maximum aggregate area or a maximum number of claims per annum. It is normal for the holder to have to drop part of the licensed area each year, so that the area shrinks annually, although exploration expenditure requirements will usually increase.These types of licences are usually used by governments to encourage exploration of otherwise unattractive or remote areas, such as the far northern parts of some of Canada’s provinces. They do not grant any real property interest in the area for which they are issued, and they will be subject to any claims or property rights that exist in the area. They are contracts with the state that grant certain exclusive rights in return for commitments to carry out work. They may or may not be specifically authorized by statute."

Jan 1, 2003

By A. G. Spencer

"The horsepower required to drive large grinding mills has increased dramatically during the past ten years. Limitations on the amount of power which may be transmitted by a single gear and pinion have resulted in the application of multimotor drives, with consequent loadsharing problems. It has also sparked the development of some entirely new drive concepts. In addition, the severe demands made upon the electrical system during the acceleration period have required that the selection of motors and electrical system design be closely coordinated. Moreover, the installation of such large process units results in downtime being very costly. The equipment selected and the plant maintenance philosophy must therefore be such as to minimize the risk of unscheduled downtime."

Jan 1, 1972

By P. J. Bourassa

Incorporated in 1957 under the laws of the Province of Quebec, Quebec Cartier Mining Co. undertook the development of its low-grade iron ore reserves located at Lac Jeannine in the southwest extremity of the Quebec-Labrador trough. This challenge comprised the construction of a 200-mile access road, two towns, a 191-mile-long railroad from Port Cartier to Lac Jeannine, a hydro-electric generating plant on the Hart Jaune River, and mining, crushing, concentrating and ancillary facilities to support a yearly production of 8.0 million tons of iron ore concentrates at 66% Fe. In order to meet increasing market demands for iron ore concentrates concurrently with the depletion of its Lac Jeannine reserves , Quebec Cartier announced, late in 1969, the first step toward bringing into production a new iron ore deposit, known as Mount Wright, located 70 air miles northeast of Lac Jeannine and 25 miles southwest of Labrador City, Newfoundland. In September 1970, the company announced its decision to develop and bring into production its Mount Wright reserves at an annual rate of 1 8.4 million dry long tons. The scope of this project included the construction of an access road linking the mine, the new town and Labrador City, Newfoundland, the extension of the railroad by some 86 miles, the construction of an ore concentrating plant with all the ancillary facilities, the development: of the mine, the construction of a pourer transmission line and a new town adjacent to Lake Daviault. The Mount Wright story is divided into five individual papers covering: (a) the history and development of the project; (b) the mine; (c) plant control by a process computer; (d) crushing, grinding and concentrating; and (e) the townsite of Fermont.

Jan 1, 1977

By Reis. E., P. Pino Véliz

"Along the process of defining the fundamentals of a ferronickel project, several questions require proper answers from the very beginning such as the size and characteristics of the laterite deposit (oxide or silicate), the mineralogical variability, and the selection of the most valuable process route. In general, these elements will be defined along the progress of the exploration and feasibility studies, and definitive engineering. Also, from the very preliminary estimates, three questions are very common: what should be the plant capacity (annual tonnes of contained nickel), what will be the probable capital required (CAPEX), and what will be the estimated timeline (schedule) between the initial stage, say the feasibility study and the plant start-up and ramp-up to designed capacity. The accuracy of the capital cost estimates also progresses along the different stages of development from ±50% at the Preliminary Economic Assessment (PEA) stage down to ±5% for the Detailed Engineering and Construction stage. These accuracies of estimates have been, in some ways, accepted by the mining community and investors. The industry accepted benchmark for ferronickel projects in terms of CAPEX are then in the order of US$50,000 per tonne of nickel contained in the FeNi product. In this paper, the authors analyze in some details three ferronickel projects for lateritic ores that have selected the Rotary Kiln - Electric Furnace (RKEF) as the suitable technological route and have started production in the period 2006–2016. Some key aspects of the ferronickel projects are examined: 1) size and type of deposit; 2) flowsheet selection; 3) evolution of capital cost as a function of capacity from the feasibility stage to construction; 4) comparison between planned production scale and actual ramp up; 5) estimated capital expenditure (CAPEX) compared with actual figures; 6) nickel price evolution and timing of the approval for the project to proceed to construction and production start-up. The objective of this paper is to identify key elements that should be addressed in future projects and that are proposed as benchmark figures for similar projects."

Jan 1, 2017

By Gang Mei, Nengxiong Xu, Yanlin Zhang

After open-pit mining finishes, an iron mine with steeply inclined ore-bodies will generally transform to underground mining. Non-pillar sublevel caving method, with horizontal slice mining from up to down, is commonly used for mining deep ore-bodies under the open-pit bottom. As horizontal slice mining proceeds, a gradually enlarging goaf will be formed under the open-pit bottom, the rocks surrounding the handing and heading sides of the goaf will collapse continuously, and then these results in rock-mass failure with large deformation and displacement in the open-pit slope. Based on FLAC3D, a modeling approach to predict pit slope deformation and failure induced by transitioning open-pit to underground mining is proposed in this paper. This method mainly consists of three procedures of modeling, i.e., mining modeling, landslide modeling, and filling modeling, of which landslide modeling is the core of the proposed approach. In the procedures of modeling with FLAC3D, iteration non-convergence is taken as a local failure criterion of pit slope. When iteration calculation cannot converge, the sliding modeling will start by deleting some elements with large displacements, and finish until convergence. Before modeling landslide, several displacement contours of rock-masses in the pit slope are searched out, and each contour is an approximate possible sliding surface of the open-pit slope. From these contours, the most proper one is selected as the slope sliding surface by using the iteration calculation convergence and minimum element deletion as the judgment condition. Landslide modeling is then realized by removing the elements outside the slope sliding surface. Finally, to demonstrate the effectiveness, the proposed approach is used to simulate the process of open-pit to underground mining at Yanqianshan Iron Mine, and to predict the deformation and failure characteristics of open-pit slope during underground mining. The case study results show that: the prediction of the slope stability determined by using our method is consistent with that calculated by using the limit equilibrium methods.

Jan 1, 2015

By Zhiwei Wang, Chunsheng Qiao

"Aiming at the problems of the existing calculation methods for the support pressures of shallow tunnels in layered jointed rock strata, by using OAT (orthogonal array testing strategy) and DEM (distinct element method), 12 influencing factors including the thickness of the weathered overburden, and the states of the rock joints were considered. Then, the classification of the loosening zone was analysized. On this basis, by using the DEA (data envelopment analysis) theory, quantitative analysis on the influencing factors was conducted. By analyzing the influence of the key factors, a prediction formula of the boundary of the ringent trumpet-shaped loosening zone was established. According to principles of stress transformation, the formula of support pressures of the loosening zone which could considering the key factors were deduced. Finally, a practical case was introduced and studied to verify the proposed method.INTRODUCTIONIn recent years, various urban subway tunnels are increasingly carried out through jointed rock strata in many cities. Rock masses are discontinuous mediums with fissures, fractures, joints, bedding planes, and faults. The frequency of joints, their orientation with respect to the engineering structures, and the roughness of the joint have a significant importance from the stability point of view. However, there is a lack of understanding about the influence of the joints on the stability of tunnels. Therefore, how to measure the degree of the joints’ influence is a problem that needs to be solved.For the calculation of the support pressures, until now, many research results were focused on soil ground (Bierbäumer 1913; Terzaghi, 1943; Peck, 1969; Sabatini et al., 1999). In terms of site tests and model indoor tests, by measuring strut loads and calculating earth pressure based on strut spacing, the results proposed by Peck (1969) and Tschebotarioff (1973) have been widely used in practice for designing excavation support systems under sand (drained) and clay (undrained) soil conditions. Note that, it is unclear whether these findings could be extended to rock strata. For numerical simulations, how to simulate the states of the rock joints is a key problem that needs to be solved."

Jan 1, 2015

By A. Brown

"The first printed report on Canada's coal resources was published in Paris in 1672(1. Written by Nicholas Denys, then Governor for France of Isle Royale (Cape Breton Island), the report dealt exclusively with the coal of the Atlantic region because little or nothing was known about the interior of North America. Clearly, also, he wrote about a resource of which much was known among the military and early settlers of that day. This early knowledge is not surprising because the presence of coal is clearly displayed in the coastal cliffs of Cape Breton as it was also, at a later date, to the first arrivals on Vancouver Island.An example of early use was that of the French garrison at Fort Louisburg in the first half of the 1700s. Still earlier, in 1643, Governor Winthrop of New England reported the receipt of a small ship load of coal from New Brunswick (2). Despite this early knowledge there was no significant development of coal mines until the 1800s. This had to await the ending of wars between the French and British factions and the growth of population. Basically, also, its development awaited the beginning of the Industrial Age. Organized coal mining began in Canada in 1825 with the formation of the General Mining Association. This British firm was the creation of a group of London jewellers which had been granted royal rights, by the British crown, to all minerals in Acadia (substantially the present Maritime Provinces). The Association took over a number of existing small mines and opened up larger operations in the Sydney coal field. Subsequently, it expanded to the mainland Nova Scotia fields at Stellarton and Springhill. The Association continued in existence as the major coal producer in Canada until 1899 when it sold its properties to the Nova Scotia Steel and Coal Company, Limited (3). This Montreal-based firm managed the coal mines as a major Canadian producer of coal until 1968 when financial problems led to the expropriation of the mines by the Government of Canada. The federal government established the Cape Breton Development Corporation to operate the larger mines on Cape Breton Island. This Crown corporation continues to be a .major producer of coal in Canada."

Jan 1, 1985

By P. M. May, V. Gella

The deportment and speciation of trace elements during mining and minerals processing is becoming an area of increasing concern with regards to potential health and environment risks. The use of chemical modelling can enhance our basic understanding of the deportment and speciation of trace metals under conditions present in gold processing solutions, and assist in laboratory and field investigations. In this paper, we report the results of chemical speciation modelling using the JESS software package for the trace toxic elements Pb, Cd, Hg, Se and Te in cyanidation solutions of varying salinity and relate the models to experimental data. The speciation of mercury is examined in detail.

Jan 1, 2011

By S. W. Marcuson, P. J. Mackey

The Canadian non-ferrous mining and metallurgical industry has made great strides in environmental protection during the past half century. The path taken by the copper-nickel smelting industry in reaching today’s level is traced in this paper. Following the practice at early copper smelters in Wales and in the US, Canadian smelters originally used tall stacks to disperse furnace of-gases. This was the normal mode of operation and was accepted by society and by Government. Gradually, Government regulations required fixation of sulphur dioxide emissions and Canadian companies responded with significant technical developments to achieve this result. The initial development in Canada of the first new technologies such as the Cominco Flash Suspension Roaster and the Freeman Flash Smelting Process - both representing early versions of the modern established flash smelting technologies - and then later technologies such as the Inco Flash Smelting Process and the Noranda Process, both of which continue to this day, are discussed in this paper in terms of their contributions to the development of environmentally friendly plants. The evolution of these and other technologies is also discussed. Some comments regarding how the industry will face the future are also included.

Jan 1, 2015

By P. Nos, L. Kolbeinsen, M. W. Kennedy, A. Filzwieser, R. T. Jones, A. MacRae

Modern furnace designs often incorporate extensive use of cooled elements to achieve long campaign lives at high operating intensities. However, contact between water and high temperature fluids can result in powerful Boiling Liquid Expanding Vapour Explosions (BLEVEs). Therefore cooling such elements with water carries inherent risks when used under slag and particularly below molten metal or matte. Alternative cooling media exist that can reduce or eliminate the risk of BLEVEs. These media are analysed and discussed in the context of deeply cooled furnace elements. Important factors in selecting alternative coolants are explored including: critical heat flux, thermal limits, toxicity, flammability, unit cost, etc. Key cooling system design criteria are reviewed in the context of both traditional and alternative coolants. Results of Computational Fluid Dynamics are presented for an example tap-block cooler design using a number of selected coolants. Research needs to advance the safe use of alternative coolants are presented.

Jan 1, 2015

By M. Askari, A. Ahmadi

"This study was conducted to establish the possible application of bioleaching in the pilot scale to recover valuable metals from the sulfidic tailings of Golgohar Iron Mine (Kerman, Iran). Using bioleaching processes, solvent extraction and sulfide precipitation recovery of valuable metals including, copper, cobalt and nickel from the tailing was investigated. The results showed that the optimum pH and temperature conditions relative to the bioleaching step was 1.5 and 45°C. The extraction of the metals from the low grade polymetal resource with complex mineralogy is very important from economic, environmental and technical point of views. Moreover, the proposed method has some advantages from energy saving, tailing management and creating added value from waste materials aspects.INTRODUCTION The growing demand for base metals and strategic such as: copper, nickel and cobalt as well as high-grade resource depletion has caused them, the mining industry to extract metals from low-grade resources and driven by complex mineralogy (Xie et al., 2005). Economic extraction of metals with low grade sources requires low-cost and efficient processing methods. A source with enormous potential for metals in future, secondary sources, such as: tailings mineral industries which the lack of appropriate technology and the high cost of processing weren't recoverable with previous procedures in the past. But it is possible that with develop new and efficient technologies have the economic exploitation ability. Recovery of metals from tailings resources is very important not only in terms of precious metals but also in terms of reducing environmental problems (due to heavy metals). The metals of copper, nickel and cobalt are mainly like sulfide compounds in the nature, usually for their recovery, first they make ore with flotation method to obtain the sulfide concentrate that containing valuable metals. then for the metal production, it will be melt and purification. Due to the environmental aspects, technical problems in the recovery of base metals from low grade ore and mixes, the presence of small reserves, in the past three decades they pay much attention to the use of hydrometallurgical processes for the recovery of base metals from these resources. These processes are classified according to the solver agent to leaching sulfates, chlorides, nitrates and amines (Hackl, 1995). Early, chloride leaching under oxidation condition in acidic or alkaline solutions was recognized the best process to produce sulfide concentrates. But then the basic processes sulfates was considered as the superior process because of being easier, a better understanding of the chemistry of leaching and recovery of base metals, especially copper from the environment easier sulfate solution with an organic solvent extraction and electro winning. The bioleaching is shown its ability on a commercial scale of low-grade sulfide minerals and ore that because of environmental reasons, the possibility of melting is not possible to them. The existing industrial base factories are based on primarily on the bioleaching and pressure leaching and recovery of cathode copper sulfate solution by extraction with organic solvents (SX) and electrowinning (EW) (Wang, 2005). Preliminary analysis has shown that valuable elements such as copper, nickel and cobalt are in the float flotation unit. Hence the plan to extract these metals from the wet tailing stream has been done."

Jan 1, 2017

By X. Q. Jiang, D. L. Chen, A. Macwan

Magnesium alloy, being the lightest structural material, is a key candidate for the weight reduction of vehicles in automotive and aerospace industries; however, its poor corrosion resistance and difficulty in deformation are limiting factors. Recently, Al/Mg/Al tri-layered clad sheets have been considered as a promising alternative to improve corrosion resistance and formability of magnesium alloys. The aim of this study was to evaluate the tensile properties and deformation behavior of Al/Mg/Al tri-layer clad sheets at different temperatures and strain rates. Yield strength (YS), ultimate tensile strength (UTS), and elongation were observed to increase with increasing strain rate. With increasing temperature from -40°C to 180°C, YS and UTS decreased and ductility increased. The strain hardening exponent evaluated via three equations of Hollomon, Swift, and Afrin et al. showed a similar increase with increasing strain rate and decreasing temperature. The fractographic analysis showed partial debonding of clad interface especially at higher strain rates and lower temperatures.

Jan 1, 2015

By P. Karimi, G. Mollataheri, A. Amini, H. Abdollahi, A. Mirzaeian

"Chah-Palang tungsten deposit is one of the two tungsten indexes in Iran. Based on ore characterization techniques (including optical mineralogy and XRD analysis), quartz, chlorite, atacamite, azurite, malachite, ferberite, illite, goethite and calcite were distinguished as major minerals. The representative sample was analyzed qualitatively by using X-ray fluorescence and chemical assay. Results showed that grade of tungsten oxide and copper were 1.76 and 7%, respectively. Also precious metals such as gold with grade of 1 ppm was reported in the sample. By using the mineralogical studies on the prepared sample, the liberation degree of tungsten minerals in –0.6 mm size fraction was obtained 80%. Several tabling tests were carried out on the original sample which at the optimum conditions and as a result, the grade and recovery of tungsten in concentrate reached to proximately 23 and 59%, respectively. To increase the grade of tungsten in the final concentrate, acidic leaching were performed on the tabling concentrate and its appropriate results indicated that the grade of tungsten increased to 27%. Also more than 90% of copper was extracted as a byproduct in the fallowed process.INTRODUCTIONTungsten, a unique hard, heavy heat-resistant metal, is distributed erratically in economic concentrations throughout most continents, occurring mostly as small irregular deposits that are not readily adaptable to large-scale, low-cost mining methods. The diverse physical characteristics and mineral composition of tungsten ores also present problems in beneficiation, requiring complex hydro- and pyrometallurgical treatment to yield high-purity concentrates suitable for the production of ferro alloys, carbides and super alloys in the steel industry (Hausen, 1989; Kholmogorov & Kononova, 2005). Tungsten is most frequently used as tungsten monocarbide, which has hardness close to diamond, in cemented carbides. The most well-known use of tungsten is in lighting filaments, and other important applications include improving steel properties and use in tungsten alloys, electronics, and chemical products (Hausen, 1989; Kholmogorov & Kononova, 2005)."

Jan 1, 2016

By J. A. Drozdiak

In this paper we examine, through pilot-scale testing, the possibility of operating a circuit comprised of two stages of HPGR comminution, followed by grinding through a horizontal stirred mill. In order to assess whether the novel circuit design could achieve the reduced energy requirements indicated in the literature, two more-established circuits, a cone crusher / ball mill and an HPGR / ball mill, were examined using a combination of testing and flowsheet simulation. The results showed that, based solely on the specific energy requirements for comminution, the HPGR / stirred mill circuit achieved a reduction of 9.2% and 16.7% over the HPGR / ball mill and cone crusher / ball mill circuits, respectively.

Jan 1, 2012

By D. R. Derry

This paper up-dates an earlier paper by the author on the rate of new Canadian mineral discoveries and the exploration methods which were principally responsible for these finds. He concludes that the ratio of exploration expenditure to production value must be increased if we are to provide sufficient new reserves for the future.

Jan 1, 1970