Search Documents

By C. R. Julian

THE large pyrites ore-bodies, the underground mining of which is to be described, are situated at Rio Tinto in the Province of Huelva in Southern Spain. The situation of the different ore-bodies with relation to one another is shown in Figure 1. It will be seen on the plan that the strike of the ore-bodies is approximately east and west. The geology of the district has been very fully described by Dr. D. Williams (1), so that for the purposes of this paper it will be sufficient to give briefly the salient features o each of the two larger ore-bodies which are being mined by underground methods at the present time. (a) San Dionisio.-This ore-body is the largest single deposit in Rio Tinto, having on its upper levels a length of 3,500 ft. On the upper levels the average width is approximately 200ft. but in places on the lower levels there is a width of 900ft. of un broken pyrites. Diamond-drill holes, without running out of ore, show the ore-body to persist to a depth of at least 1,600 ft. The ore-body in the upper part lies between slate and porphyry walls, but in depth is enclosed in porphyry walls. (b) South Lode.-Faulting is considered to be responsible for the break in the solid ore between South Lode and San Dionisio. On the upper levels, the South Lode ore-body has an unbroken length of 4,000 ft. The massive pyrites has a maximum width of 300ft. and an average of about 100 ft. Ore has been proved to a depth of 1,000 ft., at which depth the ore-body is much reduced both in length and breadth. This ore-body, to the depth at which it has been proved, lies entirely between slate and porphyry walls. The South Lode and the San Dionisio ore-bodies are mined both by open-cast and by underground methods. There is evidence that these mines have been exploited intermittently during the last 3,000 years; but, as is to be expected, no records are available of the tonnage mined prior to the time of purchase by the present company.

Jan 1, 1940

By Peter N. Calder

The orientation of planes of inherent weakness (joints) with reference to an excavation in rock is the critical factor determining stability. The purely frictional 'residual' strength remaining following the breakdown of initial cohesion is the only strength which can be counted on to resist sliding for the long term. A simple method of resolving driving and resisting forces in three dimensions along joint intersections 'undercut' by the excavation is presented. Contrary to the case of slope failure in soils, it is shown how significant changes in the slope angle sometimes have no effect on the degree of stability pre-sent in rock slopes. Wall control by reorientation of the slope, the use of cable bolts and water diversion are briefly discussed.

Jan 1, 1970

By A. O. Dufresne

A Step which, it is believed, will prove extremely beneficial to the Quebec asbestos-mining industry was taken during 1931, when the asbestos mine operators of the Province assembled to work out a uniform method of naming the products of their mines. The outcome of several meetings was the drawing-up of a classification which defined, limited, and designated anew the numerous grades of asbestos marketed. It entailed no drastic departure from the existing processes of grading, nor any revolutionary changes in methods of testing, but aimed rather to perfect existing methods. The classification proposed has been accepted by all operators in the Province, who, from January first of this year, began introducing the new nomenclature. Unless one is conversant with the properties and mode of occurrence of chrysotile asbestos, with the unique milling methods devised for its recovery, and with the history of the development of their technique, he may not readily understand the basis of the new classification. For information on these and other data concerning the industry, the reader is referred to a recent publication, Chrysotile Asbestos in (Canada, by James Gordon Ross, issued by the Mines. Branch of the Department of Mines, Ottawa. The object of this paper is to present briefly some of the phases in the evolution of the classification of Canadian chrysotile asbestos, in the hope that the recent effort to standardize the marketable products of one of Canada's most important non-metallic mineral industries will open a field for discussion, fruitful in new ideas and constructive suggestions. The necessity for the grading of asbestos results fundamentally from the fact that the price per ton depends on the length of fibre. At all times in the history of the industry, the very limited available supply of the longer grades, as well as the requirements of the trade, have caused relatively very high prices to be paid for fibre over half an inch in length, while for the shorter grades the price decreases rapidly, and at a rate which bears no proportionate relation to the length of fibre.

Jan 1, 1932

At the end of a century of mining education in South Africa, it is appropriate to reflect on the past, take stock of the present and ponder the future of mining education. While it is likely that changes in the mining industry will generate an increased demand for mining graduates, the number of suitably qualified applicants to study mining is worryingly small. While good progress has been made in unifying the educational system that previously provided schooling on a racially separate basis, it appears that a decade or more will be required to raise competency levels in mathematics, science and English, and this paper describes the process as it affects mining engineering programs. It also describes the initiatives currently being undertaken by the University of the Witwatersrand and the mining industry to ensure that the South African industry receives an adequate flow of well-qualified mining graduates, despite more than 70% of the intake coming from severely disadvantaged educational backgrounds.

Jan 1, 1999

By W. L. Murphy

The Star Lake property, located 115 km northeast of La Ronge, Saskatchewan is underlain by metamorphosed andesitic tuffs and flows which have been intruded by the dioritic to granitic Star Lake Pluton. Gold mineralization on the Star Lake property was first discovered at Ru h Lake by E. Beveridge in 1959 and by M. and E. Hird in 1961. In 1960 E. Partridge discovered Kahn 18 and Kahn 28. In 1982 the SMDC-Starrex joint venture completed geophysical and geochemical urveys including magnetics, VLF, IP/Resistivity, vegetation, bulk till and oil sampling, followed by drill testing of pecific targets. To date the most ignificant depo it is the 21 Zone which contain drill indicated reserves of 230,000 tons grading 0.5 oz/ton Au . The 21 Zone con ists of quartz with 5-10% (locally > 30%) drusy pyrite, minor chalcopyrite and trace amounts of scheelite, chalcocite and arsenopyrite. The 21 Zone is enclosed by a 25-50 m wide band of mylonitized monzonite. The mylonite occurs in the central portion of a 300 m wide northeasterly trending zone of brittle deformation .

Jan 1, 1986

By C. M. Anson

Introduction The prosperity of any country today is dependent upon the efficiency and growth of its primary steel industry. The ?march of the United States of America to its present commanding position in world affairs parallels the growth of its steel industry. The remarkable growth of that industry was possible only because bountiful providence endowed that country with adequate supplies of the raw materials necessary for steel making -coal and iron ore. If we accept this hypothesis, and surely we must, then to what extent can we envisage the future of our own country? This symposium deals with the most important of the raw materials required for steel making -iron ore. If we are blessed with a bountiful supply of iron ore, then surely a glorious future awaits only our taking advantage of that blessing. It is becoming increasingly evident that Canada has immense iron ore deposits. It is my privilege to make you acquainted with one of these, one that can only be classified as among the more important ore reserves in the world. I refer to the Wabana ore deposits in Newfoundland. Location These deposits lie under the floor? of Conception bay, off the east coast of Newfoundland. They consist of a series of beds which outcropped for a distance of about three miles on the northeastern shore of Bell Island, dipping at approximately 8° toward the northwest. This three-mile outcrop is the only key to the occurrence.

Jan 1, 1951

By John B. Phillips

The mine is entered by a central vertical shaft, strongly timbered, and containing two compartments-one for the passenger cage, the other for the large skips bringing the ore to the surface. A man-way, for emergencies, is also provided, parallel to the shaft. The cage is a single-deck steel box, carrying about thirty persons; by means of arrangements above and below, it can also hoist and lower materials needed in the workings. Levels are run at intervals of 100 feet. In special cases, where the ore conditions warrant, sub-levels are operated, such as those at 1,113 feet and 1,123 feet (Fig. 7), which are connected by winzes with the 11 th level. One of these was pushed for 40 feet, and then abandoned because it was unprofitable to take up ore of the grade encountered. The ore between levels is removed by stoping. The drifts follow the course of the veins as much as possible, with numerous cross-cuts. Winzes, raises, connections, etc., are blasted out where needed. The main drifts are at least 8 ft. high by about 9 ft. wide. All former narrow drifts had to be widened some time ago, by ruling of the Ontario Department of Mines, to lessen the danger of accidents with cars in the small passages. Accurate plans of the under-ground workings are kept in the office, and extensive surveying is always being done underground to keep the maps up to date, measure the cubical contents of stopes, and so forth. Timber is extensively used in the construction of supports and chutes, and in the sinking of the shaft. Steel and concrete are too ex pensive to compete with timber, which 1s abundant in such sections as have escaped forest tires.

Jan 1, 1926

By D. R. Jolley

"The selection of equipment for open-pit mining is an important decision which results in a considerable capital expenditure by the operator. The decision is complicated by the wide product range on the market. Certainly, equipment performance is an important criterion to consider in making the decision. Equally important, however, is the operating inter-relationship among the equipment. A poor balance increases production costs and waiting time as queues form at the bottlenecks. This inter-relationship is dependent on equipment performance, but it is also affected by management decisions (i.e. scheduling techniques).The purpose of this paper is to show how the computer is used to decide which equipment and operating decisions achieve the required production objectives at least cost. Actual mining of the pit is simulated over a period of time using different equipment and scheduling decisions. Production, waiting time and costs are evaluated for each alternative until the operator is satisfied that he has achieved the best result."

Jan 1, 1970

By M. Holmes, R. Molnar, E. Norton, K. Baxter, J. Riordan

The Boleo Copper-Cobalt-Zinc-Manganese Project of Baja Mining Corp. is situated adjacent to Santa Rosalia on the Baja Peninsula of Mexico. The El Boleo ore is a mixed oxide-sulfide deposit with major values in copper, cobalt, zinc and manganese. The metallurgical process designed to treat the El Boleo orebody involves a sulfuric acid leach in seawater using oxidative and then reductive leaching to maximize metal extraction. The leach solution is separated from the barren solids via counter current washing through a series of high rate thickeners. Copper is recovered using conventional SX-EW processing as cathode. Zinc and cobalt are extracted from the copper SX raffinate after iron and aluminum precipitation. The CSIRO DSX solvent system (Versatic® 10 and LIX® 63 mixture) are used in this extraction. Manganese remains in the DSX raffinate and is recovered by soda ash addition as a high quality manganese carbonate precipitate. Zinc and cobalt are acid stripped from the loaded DSX solvent. Zinc is then re-extracted away from cobalt using Cyanex® 272 extractant and stripped into a highly concentrated strip liquor (+100 g/L Zn) and directed to either a spray dryer or a granulator for production of zinc sulfate monohydrate. The zinc solvent extraction raffinate, containing cobalt, advances to another SX circuit using Cyanex® 272, for the recovery of cobalt as cobalt cathode. In this paper, the detailed results from bench and integrated pilot plant testing for zinc recovery from the El Boleo ore will be described. The results of this testing are currently being used to engineer the commercial plant at El Boleo.

Jan 1, 2008

By J. Tuzo Wilson

Abstract A division of part of the Canadian Shield into provinces believed to represent former mountain belts is attempted, special emphasis- being laid upon radioactive age determinations, the relation of Archaean to Proterozoic rocks, and the structure of the Grenville province. Original data on the distribution of radioactivity within several batholiths and their connection with ore deposits are' presented. The possible growth of continents and a theory which explains the shape and distribution of the world's younger mountain and island areas are discussed and applied to the Canadian Shield in an attempt to explain how the growth and present structure came about. The relation of the major mining camps of northeastern Ontario to fault zones is discussed in the light of this theory. Introduction The valuable symposium issued by this Institute to celebrate its jubilees emphasizes the important role of major faults in determining the location of many ore deposits in the Canadian Shield. Many of these faults are known to extend for long distances. It is therefore widely appreciated that it would be of great value if the pattern, ages, and causes of these faults were better understood. This would be particularly useful if the relations of the major fault systems to petrological and metallogenic provinces and to former mountain belts could be established. Each year the volume of available data, and hence the chance of reaching a fuller solution of this problem, increases. This article is a review of the present situation. It is accordingly based almost wholly upon the work and ideas of others, which are gratefully acknowledged. Naturally, responsibility for the selection and marshalling of the data is the writer's.

Jan 1, 1949

"Far from being eclipsed by petroleum and natural gas, Canadian coal continues to command wide (and apparently growing) interest.Major R & D investigations are currently heavily oriented toward coal beneficiation (e.g., cleaning and utilization of fines) and toward a broad range of studies on metallurgical coals and cokes. However, active work is also being carried out in the areas of coal geology, mining, transportation and combustion; and, in some laboratories, increasing stress has been laid on developing a number of new, essentially non-fuel uses for coal and coal products.This review summarizes the work of Canadian coal research agencies during 1966 and indicates some of the more important advances made by them."

Jan 1, 1967

By Andrew Kerr

Overview of Presentation ? Introduction ? An historical context: From 1866 to the 21st century. ? Geological framework for iron ore in the region known as the ?Labrador Trough?. ? Producing iron-ore deposits of the Labrador City ? Wabush area, and near-future production from the Schefferville area. ? Exploration projects representing potential future production?.or expansion of the district. ? Some concluding remarks???

May 1, 2011

By S. S. Dimov, B. R. Hare

This paper describes two micro-beam analytical techniques(Dynamic SIMS and TOF-SIMS) which have become an intricate part of a comprehensive analytical approach for precious metal (PM) ore characterization and process mineralogy or deportment studies. The value of the D-SIMS technique is its capacity for accurate analysis in the sub ppm range along with the ability to produce high resolution elemental maps. The TOF-SIMS is significant for speciating and quantifying preg-robbed Au on the surface of carbonaceous material. In combination with traditional assays, the two techniques can provide invaluable information regarding the distribution of PMs within an ore along with providing insight into potential sources of PM loss in processing or where losses have occurred in process streams.

Jan 1, 2011

By M. Yamine, R. J. Ring, D. J. Waters

"An experimental program has been carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's acid as an alternative oxidant to pyrolusite in the leaching of uranium ores from the Alligator Rivers region of northern Australia. Batch leaching tests on Ranger, Nabarlek, Koongarra and Jabiluka ores showed that uranium extraction was unaffected by choice of oxidant, but that Caro's acid reduced acid requirements by 15 - 25%. Lime requirements for neutralization of tailings liquors were reduced by 20 - 30%.The batch studies were extended to a four-stage continuous leaching circuit with a capacity of 400 gore h-I. Comparative leaching tests confirmed the reagent savings obtained in the batch tests. Following these encouraging laboratory results, lnterox Chemicals Pty Ltd carried out plant trials using Caro's acid. Reagent savings in the mill were similar to, or better than, those obtained in laboratory test work. The trials also established that Caro's acid has a number of operational advantages over pyrolusite.IntroductionUranium is most commonly extracted from its ores by leaching in sulphuric acid. Simple hexavalent uranium oxides and compounds are readily soluble but uranium in the tetravalent form is insoluble and must be oxidized for dissolution to occur. The most commonly used oxidants have been sodium chlorate and manganese dioxide. They act indirectly by maintaining iron as the ferric ion which oxidizes uranium by a surface electro- chemical reaction. An Fe3+ concentration of about 1 - 2 g L-I is usually considered adequate for the effective dissolution of uraninite(1)."

Jan 1, 1984

Discovery of an economic diamond deposit produces considerable wealth in terms of jobs, royalties, mining investment, and economic spinoffs for residents, including Aboriginal peoples. Diamond mines contribute to the GDP, increased personal income per person and reduced unemployment rates. Is it possible in Alberta?

May 1, 2008

By Fei Dai

Musculoskeletal disorders (MSDs) are a group of painful disorders that affect muscles, tendons, nerves, joints, cartilage, and ligaments. They are a serious problem among the workforce in the United States. In the construction industry, high physically demanding tasks expose construction workers to a number of well recognized MSDs risk factors such as repetitive motion, high force exertion, and awkward body posture. Finding ways to effectively identify and evaluate risks of MSDs can significantly alleviate this problem. To this end, this paper reviews state of practice and research in the assessment of risks of MSDs among construction workers, in which a number of biomechanical models have been developed to evaluate joint and tissue loading with the aid of state-of-the-art remote sensing technologies. Findings from the review reveal that despite the advances in tracking human motion and muscle activities, current remote sensing approaches still involve sophisticated instrumentation and expensive experiment setup. These factors greatly limited the applicability of such approaches in real construction settings. How can we detect and evaluate the construction worker?s MSDs risk in real work environments? In this paper, strategies by utilizing video surveillance systems are presented, to set the stage for addressing the above question and discussing future research in real-time, marker-less, and costeffective MSDs risk assessment.

Aug 1, 2013

By T. H. Janes

"IntroductionSULPHUR is a constituent of many industrial products. It is part •of almost anything we eat, wear, or use. In fact, sulphur is so important that there has been an increasing tendency in recent years to measure industrial growth in terms of sulphur consumption.The uncertainty of obtaining adequate supplies •of elemental sulphur from the Frasch-mined domes. of Texas and Louisiana in the United States led all countries in 1950 to seek alternative sources of supply of this necessary element.Canadian industry has been supplied, for many years, with most of its sulphur requirements by United States Frasch-mined sulphur. World demand for this sulphur has necessitated the imposition of controls on its distribution, as production has not kept pace with demand. Until the third quarter of 1950, Canadian manufacturers of pulp and paper, heavy chemicals, explosives, and textiles •experienced little difficulty in obtaining their needs of elemental sulphur from the United States. However, at that time, low producers' stocks and declining reserves threatened to reduce shipments from producers, with the prospect of a continuing shortage for some time. These conditions, together with higher prices, stimulated the search for alternative sources of supply in Canada."

Jan 1, 1952

By F. E. Senftle

Introduction The usual laboratory methods of uranium analysis are either tedious, time-consuming chemical procedures or elaborate physical methods requiring sensitive equipment. There is thus an urgent need for a method of estimating the uranium content of ore samples by approximate analysis in the field. When a new property is being developed, it is desirable to know, with the least possible delay, the uranium content of channel samples in order to guide the diamond drilling and digging operations. Prospectors, too, require approximate analyses of their hand specimens to evaluate their discoveries. To satisfy the demand for these types of analyses, several field procedures have been tried. Two general plans can be followed. One is fast but will yield only a rough estimate. The other is slightly longer but, if done carefully, will give an assay probably within 10 per cent of the true value. For field operation it is necessary to strip the more accurate laboratory methods of analysis of all refinements because of the limited equipment and skilled techniques at hand. Most of the corrections normally applied, with the exception of that for equilibrium, will not alter the gross analysis to any appreciable extent. When uranium atoms in pitchblende disintegrate, they break down into other radioactive elements, and eventually the number of elements being formed is equal to the number breaking down. The ore is then said to be in equilibrium. Certain geological processes, however, such as leaching, may selectively remove some of these elements and hence reduce the radioactivity of the ore sample. The ore is then said to be out of equilibrium. The field analysis may then be in error by as much as 50 per cent since the apparatus is calibrated with standards that are in equilibrium. However, such a large error due to loss of equilibrium is the exception, and in most cases uncorrected field types of analyr.is are justified.

Jan 1, 1949

By Yvon T. Maurice

Under the auspices of the Federal-Provincial Uranium Reconnaissance Program, a geochemical orientation survey was undertaken in an area of uraniferous Lower Proterozoic (Aphebian) rocks near Cape Dorset in southwest Baffin Island. The main objective of this study was to establish a methodology for a future reconnaissance geochemical program using lake samples over a 300-mile Lower Proterozoic rock belt that occurs along the southern coast of Baffin Island. Mineralogical and chemical studies of known radioactive occurrences, combined with detailed sampling of secondary environment media in the vicinity of the showings. indicate that uranium is the most significant pathfinder, despite considerable enrichment of other metals in the uraniferous rocks, Significant geochemical patterns produced by uranium in lake waters and uranium in lake sediments have been obtained, but their relative usefulness depends on the distribution of carbonate bedrock, which in turn affect the bicarbonate content of lake waters. In southern Baffin Island, because of erratic variation in lake-water alkalinity, it is recommended that both water s and sediments be sampled on a routine basis. The need for lake-water acidification to prevent depletion of soluble metal ions in samples resulting from adsorption on the walls of the containers and/or suspended solid matter is discussed briefly. The base metal potential of the area was examined in some detail and found to be significant, particularly for a Lower Proterozoic gossanous formation that occurs throughout southern Baffin Island.

Jan 1, 1977

By P. R. Jones

"The paper describes the CDN$400 million expansion at Hudson Bay Mining and Smelting Co., Limited’s operations. The company has continuously produced copper and zinc at the Flin Flon metallurgical plant since 1930. The paper details the company’s operational turnaround since 1995 and “The 777 Project” which includes two new mines, expansion and modification of the concentrators, expansion of the zinc pressure leach plant, a new zinc electrolytic cellhouse and modifications to the copper smelter gas handling system to reduce ground level gas emissions. IntroductionHudson Bay Mining and Smelting Co., Limited (HBMS) was incorporated in 1927 to mine and process the world-class Flin Flon copper and zinc orebody. Ore concentration and metallurgical facilities were constructed in Flin Flon. The metallurgical complex capability is currently 89 000 tonnes of copper metal and 98 000 tonnes of zinc metal from both HBMS and purchased concentrates.Flin Flon, with a population of 7000, is in Manitoba and partly in the province of Saskatchewan. The location is isolated with Winnipeg 800 km to the south and Saskatoon 500 km southwest.Today, three underground mines feed the Flin Flon concentrator, one feeds the Ruttan concentrator at Leaf Rapids, 200 km to the north of Flin Flon, and Chisel North mine feeds the Snow Lake concentrator (Fig. 1).The Flin Flon volcanic massive sulphide proximal and distal orebodies are within the Flin Flon greenstone belt which stretches from the west of Flin Flon to the east of Snow Lake, a distance of 250 km. The belt is approximately 100 km wide before disappearing below the paleozoic cover to the south."

Jan 1, 2001