Search Documents

The properties required for a com-pound to form useful thermoelectric materials are described. Uranium compounds which might have these properties are reviewed. Several of these compounds have been prepared and fabricated into compacts. The apparatus used for hot pressing, and for the measurement of thermoelectric power, electrical conductivity and thermal conductivity, is described. Detailed attention has been given to the properties of the nitrides. Preliminary studies on a number of other uranium compounds are reported. The figures of merit of the best materials so far examined are one-tenth of those necessary for a useful thermo-electric material. THE efficiency of thermoelectric materials for power generation and cooling is determined by their figure of merit, Z = a2 a/K, where a, a and K are thermoelectric power, electrical conductivity and thermal conductivity, respectively. It is well known that the largest values of Z are achieved with semiconductors (1). High mobility of charge carriers is necessary for simultaneously high thermoelectric power and electrical conductivity.The properties required for a com-pound to form useful thermoelectric materials are described. Uranium compounds which might have these properties are reviewed. Several of these compounds have been prepared and fabricated into compacts. The apparatus used for hot pressing, and for the measurement of thermoelectric power, electrical conductivity and thermal conductivity, is described. Detailed attention has been given to the properties of the nitrides. Preliminary studies on a number of other uranium compounds are reported. The figures of merit of the best materials so far examined are one-tenth of those necessary for a useful thermo-electric material. THE efficiency of thermoelectric materials for power generation and cooling is determined by their figure of merit, Z = a2 a/K, where a, a and K are thermoelectric power, electrical conductivity and thermal conductivity, respectively. It is well known that the largest values of Z are achieved with semiconductors (1). High mobility of charge carriers is necessary for simultaneously high thermoelectric power and electrical conductivity.

Jan 1, 1963

By D. T. Pritchard

"Introduction""No accounting system is very good, and all of them are infinitely variable*.”The purpose of this chapter is to discuss those facets of a typical accounting system which are most commonly encountered by operating managers in mineral processing plants. However, before concentrating in any detail on these it is important to understand the broad purposes and basic techniques of any accounting system in any major business.The three broad purposes of an Accounting System are:- Administering, controlling, and recording the flow of cash in and out of the business. Cash is, of course, converted into other assets (or stores of value) such as inventory, plant and equipment, etc. These assets also have to be administered, controlled and recorded.- Internal reporting to Management for information, for control, and for use in making business plans and decisions. - External reporting to stockholders, government, lenders and other outside parties.In this chapter we shall organize our discussion of accounting practice in mineral processing plants around these three purposes of accounting and focus in some detail on specific practices and techniques with which operating personnel will be routinely involved. This chapter is divided into the following: Accounting Basics; Administration, Control and Recording of Cash Flows; Internal Reporting; Planning and Budgeting; Cost Control; and External Reporting."

Jan 1, 1989

By G. H. Agnew

When water floods are initiated after gas-oil ratios have increased, the transition period from the start of injection until" the gas-oil ratios are returned to the solution gas-oil ratio may be important for either economic or technical reasons. The transition period is longest, and consequently most critical in water floods where injection is equal to withdrawals. This paper describes a theoretical basis for predicting the behavior of such a system and outlines a procedure for making the necessary calculations. The calculation procedure is illustrated for two actual cases: a line drive water flood and a five spot water flood. In each case there is a reasonable similarity between the actual and calculated performance.

Jan 1, 1960

By C. Gosselin, M. Rheault, M. Benoit, Y. Bouroubi, V. Sarago

The last three decades have seen significant mining development in northern regions of Canada, where the freeze and thaw cycle of permafrost and the corresponding surface subsidence and heave represent a significant challenge to the design and maintenance of infrastructures. Identifying areas at risk is of great assistance to reduce the impact of this issue. Over the past ten years, Synthetic Aperture Radar Interferometry (InSAR) has been widely used to monitor ground surface deformation. With this technique, changes in phase between two SAR acquisitions are used to detect centimeter to millimeter surface displacements over a large area and with high spatial resolution. InSAR can be used as a tool to assist the siting and design of new infrastructure as well as highlighting the risk to existing structures in areas of unstable terrain. This paper presents the results of a project carried out by Effigis, which made use of SAR interferometry in the context of monitoring terrain and infrastructure stability in a northern mining environment that is affected by permafrost seasonal and long term changes. TerraSAR-X images acquired during two periods, August to November 2012 and March to October 2013, were used to measure the deformations and/or movement of ground surface, infrastructure and stockpiles caused by seasonal changes in permafrost extent in and around a mining site located in Nunavik, Quebec. The results showed that spatial and temporal distributions of surface displacements are in accordance with scientific and terrain knowledge. Some displacements were observed in loose soil areas while, as expected, none were detected in bedrock and rock outcrop areas. The areas most affected by active layer changes showed surface subsidence in the thaw settlement period. This study confirms that SAR interferometry has a great potential for operational applications related to risks induced by surface deformation in mining environments. It shows that this technique can be used to produce reliable maps of surface movement and monitor the vertical displacement of important infrastructure.

Jan 1, 2015

By L. M. Pidgeon

MAGNESIUM metal, with a specific gravity of 1.73, is two-thirds the weight of aluminium and one-quarter that of steel. It is the lightest metal which is stable in the atmosphere. Before the war it had begun, though somewhat slowly, to take a place among the established metals. In 1939, magnesium production on this continent amounted to some 3,000 tons per annum and was confined to one company. At that time, Germany produced perhaps 20,000 tons. The advent of war, however, increased the demand to fantastic heights and introduced production problems of unprecedented magnitude. By the end of 1943, North American production is expected to reach 300,000 tons per annum (1), an increase of one hundredfold. Such a rate of expansion has not been witnessed previously in the history of metallurgy. It has given the metallurgist an opportunity to try new production methods and to learn in a short time what might otherwise have taken many years. The metallurgy of magnesium is still in its formative years and at this time widely different production methods are in operation side by side. This paper will discuss these methods in so far as information is available for publication at this time. A general description of the new Canadian industry will be included.

Jan 1, 1944

By G. R. Elliott

Foreword The office of the Supervisory Mining Engineer, a branch of the l. Federal Government, is financially interested in no oil company and has no stock to sell. This office, however, is deeply interested in the proper and efficient development of Canada's natural resources. The people of Canada are interested in the petroleum development in Turner Valley for two principal reasons: As represented by the Department of the Interior, they are the largest owners of petroleum and natural-gas rights in the field; As a nation, they are vitally interested in the development of petroleum and natural gas as a national asset, and therefore, also, in all productive property, no matter who directly controls the leases. As has been stated by Mr. Charles C. Ross, Supervisory Mining Engineer, "The Department, being responsible for the administration of these public resources, necessarily requires regulations to protect them from abuse by lessees. Our portion of this responsibility is to record a complete history of all drilling operations and to see that proper drilling methods are adopted to prevent damage and wanton waste of the valuable natural resources under discussion." Not only does our position necessitate an impartial and a judicial viewpoint, but, being day by day in touch with all operations in the western provinces, we are uniquely situated to comprehend both individual and general problems.

Jan 1, 1930

By Claudio Rocha Rosales

"Peñoles is a mining group with integrated operations in the smelting and refining of non-ferrous metals, and is also a chemicals producer. Peñoles is the world’s foremost producer of refined silver, metallic bismuth and sodium sulphate and is the leading Latin American producer of refined gold, lead and zinc. The Met-Mex Peñoles Zinc Plant commenced operations in 1973 with an annual production capacity of 105,000 t/y. Year after year the production has been increased, and at present, the production capacity is 240,000 t/y. In this paper, the leaching process,particularly the operation of the jarosite circuit is reviewed ,specifying process improvements to treat high iron calcines.INTRODUCTIONThe purpose of the leaching process is to recover the metals, mainly zinc,through a series of extraction stages with sulphuric acid solutions, which progressively increase the zinc recovery. After the series of acidification stages,the solution, which is rich in iron, is sent to the jarosite circuit to separate the zinc from the iron (Garcia & Valdez, 1996).The first step of the leaching process is the neutral leach circuit which produces a zinc sulphate solution that is sent to the purification section for the removal of impurities such as cadmium, cobalt and copper, after this solution is sent to the tankhouse to feed the electrolytic cells."

Jan 1, 2016

By R. S. Douglas

THE Granby Consolidated Mining, Smelting and Power Company, Limited, is engaged in the mining and concentrating of copper ores, and, incidentally, in the mining of coal and the production of electric power. The Company has been engaged in these various operations both on the mainland of British Columbia and on Vancouver island for the past forty-five years. This paper will attempt to cover their present operations in the Similkameen mining district of southern interior British Columbia. GENERAL CHARACTER OF THE DISTRICT The Interior Plateau in southern British Columbia ranges in elevation from 3,000 feet to 6,000 feet. In the vicinity of Princet0n, a depression in the Plateau forms a well defined basin which is floored with a series of nearly flat-lying Tertiary sediments containing some workable seams of lignite. From this basin, the upland surface rises gradually t0ward the south, from an elevation of 2,000 feet at Princet0n to 4,000 feet at Copper mountain, and 6,000 feet in the upper parts of the Similkameen basin, where it merges into the rugged and diversified t0pography of the Cascade system, with glacier inhabited peaks rising to over 9,000 feet. The valleys of Similkameen river and its tributaries are wide, having flaring sides and gentle slopes, and are separated one from another by subdued rounded spurs, of which Copper mountain is typical. The drainage of this district is taken care of by Similkameen river and its larger tributaries, such as Pasayten river, and Wolfe, Friday, and Whipsaw creeks. The name Copper mountain is applied to a gently arched, nearly flat-topped spur between the deep valley of Similkameen river to the west and the shallower valley of Wolfe creek tO the east. The mountain is appro-priately named from the number of copper deposits occurring on its sides and summit, some of which have been developed int0 an important producer, known as the Copper Mountain mine.

Jan 1, 1943

By Duanyou Li, Qing Xiao, Zhiwang Wang, Xiaoqing Gan

"Seepage is a major cause of earth-rockfill dam failure. Numerical simulation of infiltration process, distribution of drift, flow velocity and direction after the impoundment can guide seepage control and evaluate its effects. A double field coupling model is established based on soil consolidation theory and the interaction between the seepage field and the temperature field. The simulation is implemented under the situation of core wall setted, core wall not setted, and core wall setted with concentrated leakage. The results indicated that the saturation line height was significantly reduced due to impervious core wall, and the temperature distribution is uniform above the saturation line. If concentrated leakage occurs, temperature distribution of dam was significantly changed, which is consistent with theoretical inference.INTRODUCTIONEngineering seepage field distribution must be calculated in seepage control design, optimization, and correction of new engineering construction of earth dams, as well as in seepage monitoring and evaluation of existing earth-rockfill dams. The aim of calculation is to identify the important parameters in seepage field, such as the coefficient of permeability, seepage flow, pressure, head, and allowable seepage slope, for effectively implementing seepage control design, correction, safety assessment, and anti-seepage reinforcement. These seepage parameters usually can be obtained by in-situ test and back-analysis based on reliable monitoring data.In order to obtain reliable monitoring data and reflect the earth-rockfill dam seepage state and change process, appropriate monitoring technology and monitoring method is necessary. The traditional seepage monitoring method is through site inspection and sensors (e.g., osmometer, piezometric tube and measuring weir) that buried in the structure and its foundation. However, there are still some disadvantages:"

Jan 1, 2015

By L. J. Cabri

A gold sample assaying 11.4 g Ault was selected for this study. Approximately 99% of the gold in this sample occurs as discrete gold minerals; the balance occurring as invisible gold in pyrite (determined by SIMS analysis). The sample was coarsely ground and sieved, yielding -38, 17, 22 and 22 wt.% in the -400+160 um, -160+80 um, -80+40 µm and -40 µm size fractions. Assays of the size fractions gave a gold distribution of -32, 20, 21, and 27% respectively. Processing with the hydroseparator (model HS-02) gave two tailings products and one concentrate from each size fraction. Assays of the concentrate from each size fraction gave gold recoveries of -7, 7, 24, 19%, respectively. Polished sections were prepared from each hydroseparation product and studied by image analysis to automatically search for gold minerals. Calculations were done using the surface area of the grains of gold minerals found on the polished sections.

Jan 1, 2005

By C. Chapman, M. G. Reading, M. P. Amsden

Ecstall Mining Limited, a subsidiary of Texasgulf Incorporated, operates the Kidd Creek mine, a 10,000- tpd base metal producer, near Timmins, Ontario. Two different ore types are mined and milled copper-zinc and silver-lead-zinc. At the highly automated Ecstall concentrator, the ores are processed by selective flotation in three individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous onstream X-ray analysis. Recently this system was further automated by adding computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery 0.8% and zinc recovery 1.6%, and reduced reagent costs by 12%. Although not anticipated, copper and zinc concentrate grades were improved modestly as well.

Jan 1, 1973

By A. Saigal

A finite element analysis based investigation using DEFORM software was undertaken to model the extrusion of 15% alumina and 15% silicon carbide reinforced aluminum metal matrix composites. The study dealt with predicting the extrusion load as a function of ram displacement and initial billet temperature. The finite element simulation was also used to determine the maximum extrusion load, temperature distribution, maximum temperature, strain rate, velocity and stress distributions in the billet during the hot extrusion process. The constitutive equation used was of the type: Z = E exp(Q RT) = A{sinh(ao-)}" where Z is the Zener-Hollman parameter (temperature compensated strain rate), s is the strain rate, Q is the activation energy, R is the gas constant, T is the absolute temperature, a is the flow stress and A, a and n are constants. Based on the work of Davies et al and McQueen and Konopleva, the values of Q (KJ/mol), a (MPa-1), n and A for aluminum 6061 composites reinforced with 15% alumina and 15% silicon carbide used are 181, 0.024, 4.15 and 1.33x10'2 and 233, 0.052, 2.60 and 1.26xl0'4, respectively. Even though the individual parameters are quite different, it was found that the predicted maximum extrusion load, temperature distribution, maximum temperature, strain rate, velocity and stress distributions are quite similar and differ by no more than 1-2 percent between the two composites indicating that the deformation behavior is primarily controlled by the matrix material and is not a function of the type of reinforcing ceramic particulates.

Jan 1, 2004

By A. Alwasel

Musculoskeletal disorders (MSDs) threaten the wellbeing and livelihood of a large number of construction workers incurring a significant cost to society. We present a new method to monitor and diagnose MSD risks in the workplace. The sensing unit of the system is an optical encoder encompassed within a non-intrusive exoskeleton to measure the joint angle of interest. This sensor can be applied to ball-and-socket and hinge-type joints of the human body, such as the shoulder, elbow, and knee joints. The system is contactless and does not require markers or cameras. Angle measurements are acquired directly without mathematical post-processing, thereby avoiding numerical noise and drift challenges. The system is a simple, robust, and deployable, but it currently lacks resolution of parallel degrees of freedom.

Aug 1, 2013

By V. A. James

The new electrolytic copper refinery situated at Copper Cliff, Ontario, has been in operation for over a year and a half. This plant is operated by the Ontario Refining Company, Limited. The associated companies behind the enterprise are the International Nickel ?company of Canada, Limited, the American Metals Company, Consolidated Mining and Smelting Company of Canada, Limited, and Ventures, Limited. The plant was an outgrowth of the rapid development of copper resources in the nickel-copper ores of the Frood and other great mines in the Sudbury district, and of the desire to have all primary production units grouped together as compactly as possible. Starting anode furnace operations in June, 1930, and electrolytic refining on July 1st of that year, after a record-breaking construction programme completed in only fifteen months, the plant soon settled into its stride and the usual starting-up difficulties were .rapidly overcome. The rated capacity of the plant, namely, twenty million pounds of refined copper per month, has, of course, never been reached, due to depressed business conditions and latterly to the world copper agreement limiting production. It may be said, however, that the present installation has proved its ability to produce in excess of its rated capacity, and with relatively minor additions to plant and equipment that capacity can be doubled. Owing to the severity of the winters, when temperatures of from 20 to 40 degrees below zero are to be expected, the building of this refinery involved a number of problems in insulation, layout, ventilation, etc., which were rather unusual in copper-refinery construction.

Jan 1, 1932

By A. Abdollahi

Modification of the silicon in Al-Si alloys can be performed by adding a very small amount of some elements like Na, Sr and Ca to alter the form of silicon from an acicular shape to a fine fibrous one. This modification results in a considerable improvement in mechanical properties especially elongation, Metallographic observations in A356 alloy indicated the degree of the modification with Na, Sr and Ca, They showed that the effect of Ca as a modifier is not as strong as is Na or Sr while Na is the most effective modifier, Although modifiers improve mechanical properties, they also increase porosity in castings, The reduced pressure test (RPT) and Tatur test showed that the increasing porosity with Na is the most and with Sr is the least.

Jan 1, 2004

By W. Hrynewich

"The Central Canada Potash facility, a division of Noranda Metal Industries Limited, is located 3 kilometres south of the junction of Highways 16 and 2, about 75 kilometres south-east of Saskatoon, Saskatchewan. The site occupies 26~ hectares of land and includes well-equipped machine and electrical _shops, a 325,000-tonne muriate storage and reclaim warehouse, a stores warehouse, processing plant (mill), two mine shafts (one for production, the other for servicing and personnel transport), as well as a two track product loading complex. Access to the site is by road and railway (CN and CP Rail). Suppliers of operating and maintenance use both means of transportation, whereas muriate shipments are entirely by railway.Currently five continuous mining machines - one a Goodman 526 borer and four Marietta 911-A units produce some 10,500 tonnes of ore per operating day. A smaller Voest-Alpine Af.1-100 boom type miner is used for floor cutting which was previously done by a production unit. In order to maintain safe, competent ground conditions only 35 percent of the total ore is extracted. At this rate mine reserves are deemed adequate for about 100 years. The plant has operated since August 1969 and has a current practical annual capacity of 1,270,000 tonnes of muriate. As of June 30, 1981, some 11.9 million tonnes of muriate had been produced from 31.4 million tonnes of ore. Of the total muriate, 6.1 million tonnes was granular, 4.8 million was coarse, and 1.0 million was standard. No standard product has been made since August 1978."

Jan 1, 1982

By E. M. Timoshenko, A. V. Tarasov

The results of laboratory, bench-scale and semi-commercial investigations of a method for adding surfactant (technical-grade lignosulphonate) to the process of pressure leaching of nickel-containing pyrrhotite concentrates have been discussed. Lt has been demonstrated that feeding of technical-grade lignosulphonate distributed along the length of an autoclave ensures a reduction in its requirement by a factor of 1.5 to 2 as compared with single-point feeding; it also results in a decrease by 5% in the unit requirement of metallized iron-bearing precipitator in the process of non-ferrous metals precipitation and reduces by 0.05 to 0.1% (abs.) the nickel and copper contents in the tailings of the given process. Technical solutions have been proposed for commercial introduction of the process.

Jan 1, 2004

By Gui Hua Wang, Xin Chang, Zhong Ying Han, Yuan Fang Cheng

"According to the geometrical characteristics of triangular meshes, Triangular Mesh Split Model (TMSM) based on a finite element method is proposed to simulate cracks propagation of fractured rock. With TMSM, stress intensity factors at the tip of cracks are obtained by far-field contour integral. Meanwhile, vector cross multiplication is adopted to fix the cracking unit, and maximum circumferential stress criterion is used to determine the crack propagation angle. Then crack dynamic propagation simulation is realized through local mesh split or node movement at crack tip. With this method, the crack can split apart a unit or extend along the mesh boundary, so the crack could extend along an arbitrary path and is not restricted by the initial mesh. The applicability of the mesh split algorithm is verified by the crack propagation examples of wing crack and multi-fractured rock mass with holes. The results show that this method not only has higher accuracy of fracture parameters calculation, but also can accurately simulate the crack initiation and propagation of rock under complex stress state such as tension, compression and shear. In addition, the far contour integral is introduced to determine the crack tip stress intensity factor and there is no need to reconstruct a singular element at the crack tip or to intensify the meshes. Compared with the existing mesh reconstruction algorithm, this method significantly improves the computational efficiency.INTRODUCTIONGenerally, rock is neither the full continuum, nor entirely discrete body, but rich in geological defects, such as joints and cracks. A large amount of geotechnical engineering practice shows that most fracture of rock is closely related to the internal joints, cracks and crack expansion (Horii et al., 1985; Wong et al., 1998). Although the classical theory of fracture mechanics established the theoretical foundation of crack initiation, propagation, so far it is still extremely difficult to characterize the propagation of airfoil-typed crack and the interference problem of multiple cracks. Up to now, the micromechanics mechanism research of crack propagation of fractured rocks has still been a hot research topic of rock fracture mechanics."

Jan 1, 2015

By A. Baydusa, K. Barron

A theory for cutter roof failure in coal mines has been developed. It is shown that the key parameters influencing the likelihood of cutter roof failure are the rock strength, the vertical stress (depth) and the horizontal to vertical stress ratio. The support force necessary to prevent the development of this mode of failure is, in most cases, so high as to make it impractical to apply a force of such magnitude. It is, therefore, better to allow the failure to occur and to design a bolting system to support the dead weight load of the failed block. This is probably best achieved by using a yielding bolt system (such as split set bolts) which is anchored well beyond the top of the potential failure block. The maximum potential caving height determined from this theoretical approach compares favourably with field observations reported in the literature.

Jan 1, 1999

By A. Bowles

The process of accumulative roll bonding (ARB) has been applied to wrought magnesium alloy AZ31. Accumulative roll bonding results in severe plastic deformation of sheet material. In AZ31, this process leads to the refinement of the microstructure by dynamic recrystallization. The refinement of the microstructure results in an improvement in mechanical properties with potential for producing materials for superplastic forming. In this work AZ31 was bonded with up to 64 layers and the potential of roll cladding with aluminium was also investigated. The development of microstructure and the mechanical properties are reported here.

Jan 1, 2006