Search Documents

By J. Chelsey Dawson

In presenting a thesis on this subject it is advisable to explain a few of the reasons for its seeming incompleteness. World progress has brought us to a position where approximations are not only to be condoned, but regarded as absolute essentials. Production in anticipation of demand is always accompanied by mistakes on the part of the producers. Only through trial and sometimes erring hypotheses may there be evolved the true course and theory upon which the steady triumphant march of world-wide industry depends. The average person likes to have everything placed ?before him in a clear and convincing manner. It is the impossibility of doing this which, in many cases, arises to confound the writer on shales. All that one can do is to present, as lucidly as possible, the known hypotheses' and theories on the subject and leave the reader to study and work out the truth for himself. Many theories have been advanced on the origin of oil-shales ; some may be correct in certain instances and not in others; however, the writer will attempt no decision as to which are and which are not correct, but .will merely point out the relative merits of each. The figures given for reserves of oil and shale in different countries are only approximations and give but a rough idea of the true conditions.

Jan 1, 1925

By M. A. Rabah

This study aims to recover europium, yttrium metals, some valuable salts or oxides from the white powder (apatite) coating the inner surface of spent florescent lamps (SFLs). Pressure leaching using sulphuric/nitric acid successfully dissolved the metals of interest. Europium or yttrium metals were obtained by hydrogen reduction of their oxides. Addition of potassium thiocyanate converted the dissolved sulphates to thiocyanates. Selective separation of Eu and Y was then carried out by solvent extraction from the thiocyanate solution. The used solvent was trimethyl-benzylammonium chloride. N-trihutylphosphate in 1 M nitric acid was used to strip the metal loaded in the organic phase. Results showed that the quality of the cleaned glass tubes of the SFL met the standard requirement for the lamp manufacture. The white powder (WP) is composed of calcium sulphate 35.2%, phosphate 61.5% and oxides of europium and yttrium 1.65%wt. respectively. Autoclave digestion of the WP for 4 h at 120°C and 500 kPa in sulphuric acid/nitric acid mixture dissolved 96.4% of yttrium and 92.8% of europium. The conversion rate of sulphate to thiocyanate was favoured at low temperature. Stripping of Eu and Y from the loaded organic phase behaved in an opposite way. A metal separation factor of 9.4 was obtained. ate recovered europium and yttrium salts were selectively separated using ethyl alcohol or dilute nitric acid. Yttrium was very soluble while europium was not. Europium and yttrium metals were obtained by hydrogen gas reduction at 850°C and 1575°C respectively.

Jan 1, 2004

By R. V. Typliski, G. J. Labarre

"Hudson Bay Mining and Smelting Co., Limited, Flin Flon, Manitoba, Canada, has developed a metallurgical wastewater treatment system employing two-stage lime neutralization, sludge recirculation and conventional mechanical thickening.Laboratory investigations, initiated in 1970, led to the construction of a pilot-scale minewater treatment plant, at Schist Lake Mine, in early 1971. This plant, treating 600 cubic meters/day wastewater containing 30-60 mg/l zinc, demonstrated metal extraction efficiencies of 99% under normal operating conditions.On the basis of this pilot work, a second pilot-scale treatment system was established in 1975 at the Flin Flon metallurgical plant to treat zinc refinery process waste water. Through numerous improvements, including automatic control equipment, the system has evolved to a full-scale operation capable of treating 800 cubic meters/ day wastewater containing 4-11 gm/l zinc. Treated effluent contains 0.2-20 mgll zinc. Hydroxide sludge produced returns to the metallurgical process for recovery of metals while clarified effluent discharges to waste.With the system, Hudson Bay Mining has achieved its original goal: the reduction of environmental contamination, while realizing ii return from metal recovery."

Jan 1, 1980

By C. S. Parsons

Introduction Up to the present, the operation of small mills for the treatment of gold ores has not been favoured in Canada to the extent that it has in other countries. For instance, a list of the operating properties in Southern Rhodesia, published in The Rhodesian Mining Journal of November, 1934, shows for the month of September, 1934, that there were over 500 small mills treating less than 50 tons per day, and the majority of these between 5 and 25 tons. They are operated by individuals, syndicates, and small mining companies. It is presumed that the operations are profitable, although from the published figures of the tonnages treated and the yields, it is difficult for one familiar with Canadian operations to understand how this can be possible, in the majority of cases. Most of these small mills employ stamps with plate amalgamation and with, occasionally, tables to produce a concentrate. Enquiries have been received from many parts of the world respecting milling practice suitable for small gold mines and the type of plant used in Canada. The tenor of these enquiries leaves the impression that the majority of the writers assume that the practice would be similar at all small properties. This, of course, is not the case. Conditions vary widely, and what would be a suitable mill for a typical Nova Scotia ore would not necessarily be wholly adaptable to many ores in Ontario, Quebec, or British Columbia. This paper has been written with the intention of inviting discussion, and it is hoped that, by such discussion, the subject will be more fully dealt with than has been possible in the time at the disposal of the writer. Only more or less standard principles and practices have been dealt with, and, purposely, no reference has been made to plants using mills of the Hadsel, the Nutt, or the Gibson type. As there is available but little reliable information on the costs of installation and operation of small mills, it is also hoped that those contributing to the discussion of milling practices for small mines will be in a position to give these data for the benefit of those contemplating the erection of small plants in Canada. Although it is difficult to generalize, it can be said that there are three types of gold mills commonly used at small mines: (1) Amalgamation and Gravity Concentration; (2) Amalgamation and Flotation; and (3) Cyanidation.

Jan 1, 1935

By F. Qi, T. Frišcic, C. Mottillo

"One of the principal goals of modern industry is to minimize the environmental impact and increase the materials- and energy-efficiency of transforming raw materials into valuable products. This paper will highlight our latest laboratory-scale research in low-energy, low-solvent reactivity of metal oxides and their conversion into popular metal-organic frameworks (MOFs), zeolitic imidazolate frameworks (e.g. Basolite® Z1200 component ZIF-8), and metallodrugs (e.g. bismuth subsalicylate, active component of Pepto-Bismol®). Mechanochemical ion- and liquid-assisted grinding (ILAG) and ""accelerated aging"" techniques will be presented, along with novel low-energy and solvent-free approaches, inspired by geological weathering processes, for converting metal oxides into metal-organic materials. INTRODUCTIONThe development of environmentally-friendly processes, which would in the same time be more materials- and energy-efficient than the existing ones, is one of the central concerns of modern chemical research. In that sense, the focus of the chemist has been mainly on the preparation of carbon-based organic molecules and adaptation of traditional organic synthesis to the recently delineated ideals of Green Chemistry. However, there is a growing realization within the chemistry community that significant energy, materials, and ecology-related benefits can be achieved and, indeed, targeted in the transformations of materials that are typically associated with inorganic chemistry and minerals processing. The principal aim of this highlight contribution is to illustrate how, through the use of approaches associated with solventfree chemistry and mechanochemistry (James et al., 2012), one can develop a clean and efficient system of chemical and materials transformations involving oxide precursors that normally belong to the realm of inorganic chemistry and mineral processing. In particular, this contribution will provide an overview of the recently developed mechanochemical and solvent-free reactivity of metal oxides towards small organic molecules. These mechanochemical reactions, including the methods of liquid-assisted grinding (LAG, Frišcic & Jones, 2009) and ion- and liquid-assisted grinding (ILAG, Frišcic, 2010), have so far provided a radically different means to construct advanced metal-organic materials (e.g. porous metal-organic frameworks, [MOFs] or metallodrugs) by rehabilitating metal oxides as precursors, eliminating the use of bulk organic solvents, and avoiding the use of high temperatures."

Jan 1, 2012

By B. K. Gorain

"As mining has evolved over a century, so are the challenges associated with mining. Mining of complex ore bodies at greater depths is a major challenge requiring high capital and operating costs due to remote locations, high energy costs, water quality and complex environmental issues. In addition, the stakeholder expectations are growing along with challenges associated with highly complex mine permitting processes and changing demographics of mining jurisdictions. The dynamic metals market adds to these challenges impacting the long term development and sustainability of mining projects.These challenges are compelling mining companies to look at various innovations with an integrated approach focusing on meeting the needs of various stakeholders. Mining companies are slowly tapping into some successful concepts that have transformed other industries such as manufacturing, chemical, pharmaceuticals along with oil and gas.This paper provides an overview of various innovations and technology developments in mineral processing that have shaped the current mining industry. A glimpse of the present and future challenges in mining is also presented. An integrated approach to problem solving involving various stakeholders is gaining momentum and this has been reflected in this paper. Various developments that are being pursed in mineral processing focusing on a change in the existing mining paradigm are also presented in this paper.INTRODUCTIONAs mining is evolving, so are the challenges associated with mining. Some of the key challenges are complex ore bodies at greater depths, high capital and operating costs, water scarcity and quality issues, high energy costs, complex environmental issues including tailings management, worldwide constraints on resource availability, more and more elaborated regulations in emerging economies impacting the permitting processes, increasing stakeholder expectations, changing demographics of mining operations with ever-changing cultural or community expectations and the urgent need for a better assessment of project viability, this in very dynamic metals markets impacting the dynamics of mining projects development and sustainability."

Jan 1, 2016

By K. Janghorban

Multilayered ceramic-metal composites were produced by solid state diffusion bonding of polycrystalline alumina and three Al alloys containing 1 to 2%Sr, 2% Mg and Mg + Si (5057 Al alloy), The multilayered structures were fabricated at 610°C under a compressive stress of 3 MPa for 2 hours in He-5%H atmosphere, The ceramic-metal interfaces were studied by SEM and TEM equipped with energy dispersive spectrometer (EDS). Addition of 1 wt % Sr to Al promoted good adhesion, without producing any interfacial products, while the Al-2%Sr was poor in this regard due to the presence of dispersed A14Sr which is an intrinsic phase in the Al-Sr phase system, The Al-2%Mg alloy produced a continuous film at the interface, which was characterized to be MgAl2O4. Al alloys containing Mg and Si (5057 commercial alloy) produced not only the spinel structure (MgAl2O4), but another phase rich in Mg and Si (close to Mg2Si), These latter interfacial reaction products were not the intrinsic phases in Al-Mg alloys, and were reaction products at the Al2O3 ?Al alloy interfaces.

Jan 1, 2005

By P. L. Li, B. X. Song, C. H. Wang, T. Wang, Z. Hu

"The treatment of an oxidized copper-gold ore by stage cyanide addition was investigated. For cyanidation, free cyanide ion concentration can be an indicator of whether there is copper dissolved in cyanide solution, and maintaining the free cyanide ion concentration lower than 1.0 g/L could be an effective way to prevent copper dissolution and reduce cyanide consumption. For that purpose, stage cyanide addition was introduced to control free cyanide ion concentration within the range from 0.8 to 1.0 g/L. Cyanidation tests results indicate that gold extraction was still acceptable at reduced cyanide consumption with a lower copper extraction. Based on the experimental study, industry application works at Beiya concentrator of Yunnan province, China were successfully conducted. When the raw ore contains 2.95 ppm Au and 0.75% Cu, by stage cyanide addition method, the gold extraction was still 93% at reduced cyanide consumption of 2135 g/t, which was only half of one addition method, and the copper extraction dropped to only 5%, which indicated that dissolution was prevented for almost 75% of the malachites.INTRODUCTIONCyanide with its competency to form a strong complex with gold, is the most preferable lixiviant for gold leaching. However, cyanidation is not inherently a selective process since many other minerals present in the ore are also readily soluble, especially the copper minerals. Muir (2011) reported that every 1% reactive copper present in the ore consumes about 30 kg/t NaCN, which can have detrimental effects on the process efficiency and economics due to high cyanide consumption, reduced gold leach rates and poor gold recovery."

Jan 1, 2016

By Jesús L. Valenzuela, José R. Parga, Salvador Aguayo, Héctor Moreno

The Merrill Crowe zinc-precipitation process has been applied worldwide on a large number of operations for the recovery of gold and silver resulting in a higher consumption of zinc dust from cyanide solutions. However, in some of plants this precipitate is of low quality, because lead, cadmium and especially copper are precipitated along with gold and silver. The low quality precipitate also requires more fluxes in smelting and shortens crucible life. In this study, a process is introduced to remove copper, silver, lead and cadmium from barren solutions following the Merrill-Crowe process. Copper and silver are removed by precipitation in a serpentine reactor, using sodium sulfide as the precipitator, and sulfuric acid for pH control. The recovery of lead and cadmium ions with natural hydroxyapatite using cow bone powder (CBP) as a new adsorbent material, is introduced. CBP is capable of removing lead and cadmium ions from aqueous cyanide solutions with 99% efficiency. It has the ability to compete with other existing commercial adsorbents for the removal of lead and cadmium. Results show that pH value has a significant effect on copper cyanide removal efficiency, and it was determined the optimal pH range to be 2 - 3. At this pH value, the copper cyanide removal efficiency achieved was up to 99 %; and for the cyanide associated with copper cyanide complexes, the recovery was 90%. Finally, the precipitate quality was improved 400% .This procedure was successfully run at three mines in México.

Jan 1, 2014

By Habib Zughbi, Paul Zulli

"A key step towards sustainability in iron and steelmaking is to optimise the use of raw materials and energy consumption, and consequently minimise CO2 emissions. Models based on a Process Integration (PI) approach play a key role in evaluating various scenarios and the impact of introducing changes in raw materials and operational conditions on the overall energy consumption and CO2 emissions. BlueScope uses a PI based comprehensive model for its Port Kembla Steelworks (PKSW), called the Integrated Steelworks Energy and Emissions Model (ISEEM). ISEEM is tightly coupled to the configuration of PKSW. It is based on mass and energy balances as well as thermodynamic relationships. ISEEM is a steady-state model and is used to predict overall and detailed unit-by-unit energy consumptions and CO2 emissions. It is also used for plant-based scenario modelling. This paper investigates the impact of major changes to PKSW configuration, including the shutting down of a blast furnace and cokemaking battery, on the energy consumption and CO2 emissions of the plant. It discusses some of the issues involved in updating the model and some identified opportunities."

Jan 1, 2015

By D. L. Cluff

Ventilation Air Methane (VAM) is a high volume low concentration methane source. The capture or use of methane from VAM is challenging, which results in the routine discharge of methane into the atmosphere. Mitigating VAM has the benefits of providing an energy source and reducing the atmospheric Greenhouse Gas (GHG) burden. The GHG radiative forcing effect of methane is 17?23 times as potent as carbon dioxide on a 100-year time horizon. Thus, any reduction in atmospheric methane would be beneficial. The calorific value of methane is 55.5 MJ/Kg; therefore, a 100 m3/s flow with VAM concentrations from 0.1?1% can provide 3.8?38 MW of exploitable power. Strategies to mitigate VAM such as: Thermal Flow Reverse Reactors (TFRR), Catalytic Flow Reverse Reactors (CFRR), Lean Burn and Catalytic Gas Turbines, Biothermica Vamox®, Megtec VOCSIDIZER©, and Vamcat? are briefly reviewed. The review of VAM mitigation technologies reveals disadvantages such as the need to maintain a minimum internal heat capable of oxidizing the methane. This requirement uses all of the available methane up to the point of reaction sustainability and up to half at the highest methane concentration in VAM. Some systems may introduce a pressure drop to the ventilation system, which would impinge on the existing ventilation system design. These impediments necessitate the development of a more amenable technology. In the proposed system, gas turbines (GT), coupled to a combustion chamber with an external fuel supply, assist the combustion of the VAM. The combustion-chamber coupled system provides electricity, while the heat contained in the GT exhaust gases increases the temperature of the VAM, encouraging the development of a flame inside a combustion chamber. The flow from the combustion chamber streams through a primary air/fluid heat exchanger capable of producing steam of a high enough quality to generate electricity using conventional steam turbines. The residual heat after primary extraction, directed through other equipment, provides additional heat based products such as industrial scale dry air, chilling by an absorption chiller or hot water. The overall design of the system is scalable for low to high VAM flows or variations in concentrations and is capable of providing the company or community with heating, chilling, hot water, electricity or motive force as needed by the particular site or community. The Multi-generation system uses heat from three sources to provide clean efficient energy while mitigating the atmospheric emissions of methane. These sources are heat from the GT, often considered waste heat, heat from fuel injected into the igniters and heat from the VAM. The opportunity to collect carbon credits may improve the economics. In order to design a system with this capacity, a detailed analysis of the combustion characteristics of three separate flows is required. VAM is the main airflow, having the highest volumetric effect, while the GT exhaust and the additional fuel added to the hot exhaust flow of the gas turbine are lower flows, but have a higher velocity and temperature. The aim of the modeling undertaken in this work is to establish the combustion dynamics, degree of pre-heating required and the geometry essential to the design of combustion based VAM mitigation multi-generation systems.

Aug 1, 2013

By L. E. Djingheuzian

"IntroductionDURING the past two decades an enormous amount of empirical data has been accumulating on grinding. These data have been obtained by mill operators on grinding ores with a diversity of characteristics, and generally they have been published. However, whenever an operator, who has started milling on a new ore, has tried to find a case in literature which would exactly fit his particular grinding problem, he has failed. Evidently, something fundamental has been lacking in all these empirical data, and, as a consequence, each new operator has had to undertake his own experimenting, get the best results he can, maybe publish these results, and let it go at that. This, in the writer's opinion, has been• due to the fact that even the ablest and most inquisitive millman has been forced to look on grinding as an art, and so, except very rarely, has not been able to find the time to stop and think; if he did so, it was rather in a philosophic way, that grinding is a fundamental process, a process that takes place in river beds, on the sea shore, etc.Nevertheless, when all the data so far published are correlated and examined as a whole, one is struck with the advances that have been made in grinding. The writer (7) had made such a study in 1949, and, when the correlation was completed, it showed that there was nothing heterogeneous about the accumulated data and that when brought together they were in harmony with each other. The writer's conclusion was that, if grinding criteria were defined and were expressed in such a way as to make integration of any data into basic formulae possible, grinding would be established as a mathematically exact science, and grinding worries of the harassed mill operator would be at an end!The first attempts to rationalize comminution were made by Rittinger and Kick. However, their theories led to endless disputes which did not accomplish much, except possibly clearing the path for subsequent investigators."

Jan 1, 1952

By I. Tinto

"IntroductionEnvironmental pollution problems, caused by gases or effluents, by high noise levels or from air borne dust, are placing increasing demands of the operators, from statutory authorities, and from the general public, to adopt more stringent dust control measures. This requires that a successful plant dust control program be an integral part of any plant operation. While a successful environmental program is a key factor in maintaining productivity and good labour relations, anticipation of future environmental regulations during the plant design phase can avoid the high cost of plant upgrading, or dealing with pulmonary conditions in the work force in subsequent years.Particulate removal, conventionally called dust collection, involves the removal of coarse- and fine-particulates from the airstream. Although generally limited to that required for contro!Hng plant generated air emissions, particulate control equipment also has a wide application for air cleaning and filtration inside the plant, as well as for recovery of usable products.In the late 1950s and early 1960s the public became more concerned with the problems of air pollution. This increasing concern was stirred by an awareness of the extremes to which water pollution had progressed in many of the rivers and lakes, by increasing perception of air pollution as detected by visible smog and harsh chemical odors, by the alarming rate of increase of smog plagued cities and communities, and by specific incidents where ill health could be traced to specific episodes of air pollution. Particle size is perhaps the most important single factor affecting particulate control. Large particles (over 5 microns) constitute the major mass fraction of most sources of emission and economical control equipment dqes exist for their efficient control. However, while these larger particles frequently represent the source of soiling and unsightly smoke plumes, they are not a major health problem as they tend to settle relatively quickly, are more easily scrubbed from the atmosphere by rain, and are not able to penetrate the respiratory system. By far the most important form of particulate air pollution is the fine particulate, (below 3 microns) which is harmful to the pulmonary system. The adverse effects caused by this particulate matter on human health are for the most part related to injury to the surfaces of the respiratory system. Particulate material in the respiratory tract may produce injury itself, or it may act in conjunction with gases, altering their sites or their modes of action. A combination of particulates and gases may produce an effect that is greater than the sum of the effects caused by either individually (i.e. synergistic effect)."

Jan 1, 1989

By S. Downing, T. Grammatikopoulos, N. Hoffmann, C. Gunning

"Most deposits display a high degree of geological and mineralogical complexity that can affect metallurgical processing. Therefore, the proper characterization of the ore and gangue minerals requires a multi disciplinary approach combining geology, mineralogy, geochemistry and processing. However, mineralogy to a large extent informs the metallurgical process. Automated methods can be used throughout the mining chain from advanced exploration through to production.In this presentation we discuss actual case studies where automated mineralogy has been applied in a geometallurgical framework at a pre-feasibility to feasibility level. These include examples from a strongly serpentinized magmatic Ni deposit (Dumont) and a magmatic Cu-Ni deposit (Maturi). Mineral speciation and ratios, e.g., chalcopyrite, cubanite, and pentlandite/pyrrhotite are critical to model the Cu-Ni magmatic deposit. In the serpentinized Ni ore, automated mineralogy is used to speciate the Ni minerals into sulphides, alloys and refractory Ni in the silicate matrix.The mineralogical results are linked to the metallurgical test work in order to model the geometallurgical domains. These case studies will illustrate how mineral quantification and improved understanding of inherent mineralogical parameters in relation to metallurgy reduce technical risk in both exploration and flowsheet development.INTRODUCTIONGeometallurgy is a cross-discipline approach combining geology, metallurgy and mine planning (e.g., Dunham et al., 2011). It is aimed to improve the understanding of geological, mineralogical and metallurgical parameters of an ore. Informational gaps among the different disciplines are often apparent. Automated mineralogy is shown in many studies (e.g., Eppinger et al., 2013, Philander and Rozendaal, 2013) to constitute the link between geology and metallurgy. The geometallurgical approach can provide specific data to geology, mining and mineral processing development and plant operations. The scope of the automated mineralogy is to illustrate how mineral quantification can improve the understanding of inherent mineralogical parameters in relation to metallurgy, and reduce the technical risk in both exploration and flowsheet development."

Jan 1, 2016

By L. K. Sinclair

In situ leaching of copper has the potential to deliver low-cost recovery for soluble copper deposits of sufficient permeability. In order to provide key inputs for modeling of the in situ leaching process, bench scale test work can be used in conjunction with geochemical software to identify key leaching and precipitation reactions. A case study is presented in which a series of flow-through acid leaching tests were conducted on drill core sections from a porphyry copper deposit without crushing or grinding. Concentrations of copper and other key elements were monitored in the recirculating leach solution over several months. A geochemical model of each leaching test was prepared using Geochemist's Workbench using a combination of diffusion-controlled and reaction-controlled rate mechanisms. Key reactions included leaching of chrysocolla, iron oxides, and plagioclase. The model was able to simultaneously satisfy the evolving chemistry of the recirculating leach solution, mineralogy of the head and leach residue, measured acid consumption, and leaching rates for key minerals reported from previous laboratory studies. Opportunities and limitations for scaling up the model to simulate the commercial wellfield are discussed.

Jan 1, 2015

By F. E. Lathe

INTRODUCTION THE present study, based largely upon phase equilibrium diagrams and other theoretical considerations but nevertheless addressed primarily to the practical metallurgist, has been undertaken with a view to discovering what light can be thrown upon the role of alumina in slags. According to Liddell (23), "alumina apparently acts as .a base if much silica is present, as an acid if the silica is low, always as a nuisance." Newton and Wilson (26) state that .alumina "is never added intentionally, as it makes the slag viscous, and is generally an undesirable constituent of slags". Camp and Francis (3) sum up their views by saying, "alumina is seldom used intentionally as a flux, but it is present in nearly all raw material, hence unavoidable". One has only to read The Function of Alumina in Slags, by Henrich (I3), and the very extensive discussion that followed the presentation of his paper, to realize that, before the days of phase equilibrium diagrams, it was a very serious question indeed as to whether alumina should be calculated as a basic, acid, or neutral constituent. Opinions then differed widely, as well they might; today, even though no categorical answer can be given to the question raised, the function of alumina can be at least partly clarified by a study of the fundamental work done by the Geophysical Laboratory in Washington and by certain universities in both America and Europe. It will be a source of gratification to Canadian metallurgists and ceramists to know that work of this type is now under way in the recently organized Physical and Crystal Chemistry Section of the Mines Branch, Ottawa, and that results of practical value have in fact already been obtained.

Jan 1, 1951

"Many underground mines are achieving extended life and optimizing existing facilities by mining at greater depths. The challenges to do this require a sound engineering approach to mine design and mine services, as well as ingenuity in safety design. The social consequence is full utilization of existing infrastructure.Accessing ores at depths of 2000 m to 3000 m requires exceptional hoisting design. May’s theme issue includes a paper that examines a case study of one such hoisting plant, with emphasis on the hoist rope selection at Agnico-Eagle’s Penna shaft. The paper also describes the process whereby consultation with provincial safety authorities resulted in a revised safety factor suited to the hoist. Another paper examines the challenges of ventilating mechanized mines to 3000 m, including air cooling and dilution of diesel exhaust emissions. Vent system designs are discussed, using sound engineering design, and proven technology that minimizes emissions to achieve cost efficiencies. The paper suggests design based on process and ventilation simulators to obtain realistic economic data at the design stage. Increased ground pressures present unique challenges for production and safety. While this is not confined to deep mining, one paper examines rock pressures and seismic events at the Brunswick mine, for which experience may be applied at depth. It describes seismic monitoring as a predictive tool in a real mine situation, and how it is used to improve overall recoveries and maintain worker safety."

Jan 1, 2004

By Knud Sinding

Environmental reporting by mining firms takes many forms and change frequently. The objective of these reports is related to increasing the legitimacy of mining firms with their diverse stakeholders. This study, focusing on internet-based reports, shows that there are considerable variations in reporting. This phenomenon is interesting because it belies the efforts pursued by leading industry members under iniatives such as the Global Mining Initiative and the Mining, Minerals and Sustainable Development project. The observed variation, both internally among reports and between reports and other industry policy statements, suggests that the industry needs to explore the possibilities for more convergence in terms of reporting quality. Based on theoretical constructs from the management literature we present a series of arguments defining necessary and sufficient conditions for durable and well-institutionalized reporting practices and standards.

May 1, 2002

By G. P. Contractor

Medium and low carbon steels, modified with uranium, were studied in order to evaluate the influence of uranium on forge ability, mechanical 11roperties, response to heat treatment and microstructure. Uranium contents ranged up to 0.70 per cent. The medium carbon steels are hot short if the uranium content exceeds about 0.35 per cent. More uranium can be tolerated in low carbon steels. The hot shortness is caused by the formation of intergranular phase UFe2. Critical transformation temperatures, Jominy hardenability, and resistance to tempering are not significantly affected by the 11resence of uranium. Similarly, uranium has little or no effect on the tensile properties of carbon steels. The addition of uranium has a favourable effect 11n the stress-rupture characteristics and some beneficial effect on fatigue properties. However, more results are required for verification. In the steels investigated, it seems that most of the uranium carbide combines to form complex inclusions of U (0, C, N) or (C, N), rich in oxygen or nitrogen or both.

Jan 1, 1963

By Robert B. Parsons

"Finance Minister Paul Martin's second budget might be good for Canada's mining industry in the long run, but the budget raises a number of concerns for the industry in the near term. The budget papers suggest that the 25% resource allowance is not working as intended, and report that the Department of Finance will be reviewing this valuable allowance. The so-called ""large corporations tax"" rate will be increased. This annual tax, which is imposed on a corporation's capital even when the corporation is not in production, is particularly harmful to the mining sector.IntroductionThe Honourable Paul Martin, in his second federal budget, emphasized spending cuts and made only modest tax changes. However, two of these tax changes could have a serious impact on the Canadian mining industry: the proposed review of the 25% resource allowance; and, the increase in the large corporations tax rate.Personal Tax Measures Personal Tax Rates UnchangedThe government has been under political pressure not to increase personal tax rates. Mr. Martin's announcement that rates would not change will be popular."

Jan 1, 1995