Search Documents

By N Kojola, A Vickerfält, J Huss

The possibility of using an acidic autogenous hydrogen direct reduced iron (H-DRI) slag as a basis for vanadium extraction is investigated. For a raw material to be suitable for producing high-quality FeV, the vanadium oxide content should be sufficiently high and the phosphorus oxide content in a tolerable range. Therefore, the feasibility for vanadium extraction relies on fulfilling two demands: the predominate partitioning of phosphorus to the metal and vanadium to the slag. Correspondingly, the behaviours of phosphorus and vanadium in the Al2O3-SiO2-FeOx-VyOz-P2O5-Fe system were studied experimentally. Slag, 10 g, was put in contact with liquid iron, 30 g, for different durations (2–24 hrs) in closed alumina crucibles at 1873 K. The slag composition was varied between 33.1– 49.3 wt per cent Al2O3, 27.1–46.7 wt per cent SiO2, 16.6–30.1 wt per cent FeOx, and 2.5– 8.8 wt per cent V2O3. The equilibrium phosphorus distribution was 0.42, while the vanadium distribution ranged from 7.6 to 43.4, increasing with the Al2O3- and the FeOx-content.

Jun 19, 2024

By D J. Brake

There are many sources of gas in underground mines including development and production blasting, strata gases, spontaneous combustion, diesel equipment, chemicals used for a wide range of functions, welding activities and fires.It is only in relatively recent times that electronic gas monitors (or detectors) have become both safe and affordable for routine use.In modern mines, gas monitors should be in daily use by the ventilation department as well as blasting re-entry (or clearance) crews, and are often used by drilling crews, shift supervisors, hygienists and mine rescue or fire fighting crews.When first released, electronic gas monitors needed to be sent off-site periodically for calibration at a suitable accredited laboratory. Between calibrations, their accuracy was unknown. More recently, ‘bump testing’ and field calibration has become possible on the mine site, improving both reliability and safety as well as reducing the total number of gas monitors that need to be in use.There has been almost an overwhelming increase in the number and sophistication of gas monitor features in recent years. This paper reports on a case study into the key criteria that ventilation practitioners should be aware of with respect to the specification and selection of the most recent gas monitoring systems, and recommends good practice for site-based operation and calibration.CITATION:Brake, D J, 2015. Specification and selection of hand-held gas monitors (detectors) for underground mines, in Proceedings The Australian Mine Ventilation Conference, pp 143–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D Anderson, W Timms

"A geotechnical centrifuge can characterise and model the interaction of tailings and fluids over very long time periods by accelerating drainage and consolidation processes. This technology can be considered an environmental ‘time machine’ for designing and evaluating tailings storage projects and verifying numerical models. The Broadbent G-18 geotechnical centrifuge (2 m diameter, up to 875 rev/min) and associated equipment is a unique facility commissioned in 2011 at UNSW Australia for applied research in low-permeability materials such as mine tailings. Two centrifuge modules are available: the permeameter module for characterisation and physical modelling and the strongbox module for physical modelling.This paper presents examples of geotechnical centrifuge applications for the: consolidation of slurries and dewatering design of earthen barriers compatible with tailings chemistry prediction of contaminant mobility. The specifications and capability of the UNSW Australia geotechnical centrifuge and associated instrumentation is also presented, along with preliminary analysis of the confidence intervals associated with permeability testing of a set of samples of varying heterogeneity. Drainage velocity through a mine tailings sample increases linearly with g-level in the centrifuge permeameter until tailings consolidation occurs. Alternatively, geotechnical centrifuge experiments can be designed to limit consolidation so as to quantify permeability changes that may occur with geochemical interactions between fluids and mine tailings or earthen containments. Reactive solute transport through mine tailings can be simulated at realistic solid:liquid ratios when chemical equilibrium is maintained during geotechnical centrifuge testing. Carefully designed physical models of tailings disposal tested at accelerated gravity can therefore provide a realistic evaluation of tailings consolidation and drainage and the potential for subsurface migration of contaminants from mine tailings over long time periods.CITATION:Timms, W and Anderson, D, 2015. Geotechnical centrifuge technology for characterising the interaction of tailings and pore water over decadal time periods, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 247–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By T Trott, M Lewis, G Lumley

The analysis of equipment trends in The AusIMMÆs revision of Monograph 19 - Australasian Mining and Metallurgical Operating Practices (AMMOP) (in prep) in the paper by Graham Lumley raised some interesting, and in parts disturbing, trends in the Australian open cut mining industry. According to the Australian Bureau of Statistics (2011) the productivity of the whole mining industry is down by 34 per cent since 2001. In terms of open cut equipment, median output for draglines is down by 15 per cent since 2003, electric rope shovels are down by 41 per cent since 2003, hydraulic excavators are down by 39 per cent since 2008, front-end loaders are down by 39 per cent since 2007 and trucks are down by 41 per cent since 2006. Clearly e boom has not been good for the efficiency of the mines. During this same time, best practice (defined as the average of the top ten per cent by annual output per unit of input) has declined, but not by as much as the median (eg shovels down by eight per cent, excavators down by 19 per cent and FELs down by five per cent). This paper will build on the analysis of AMMOP to understand the differences occurring between median and best practice and identify the factors contributing to the decline in performance. As the industry enters a period of potentially lower prices for commodities and reduced margins, pressure will be brought to bear on mine sites to start moving more with the equipment they have. An understanding of where efficiency has been lost will be a key component in that. The information contained in AMMOP, and the subsequent analysis of that information in papers such as this one, will be crucial to reversing the decline in open cut equipment performance.CITATION:Lumley, G, Trott, T and Lewis, M, 2012. Reversing the trend in open pit mining equipment output, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 75-82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By Carter A. J, Miller D. M, Holder N. H M, Van Aswegen P C

The Harbour Lights Mine situated at Leonora in Western Australia, mines a refractory sulphidic gold ore. The main sulphide minerals are pyrite and arsenopyrite. Due to the association of gold with the pyrite and arsenopyrite, gold recovery is not amenable to the normal cyanidation process.A pyrite/arsenopyrite flotation concentrate is produced at Harbour Lights. This concentrate has been stockpiled for the past two years.A bio-oxidation process (BIOX«)* to treat refractory gold flotation concentrates has been developed by GENMIN in South Africa. Harbour Lights acquired the technology from CRL BIOX« Pty Limited in Brisbane, to treat the refractory gold concentrates.

Jan 1, 1992

By F F. Pitard

The optimisation of a metallurgical plant requires two kinds of sampling systems. The first provides samples to follow process changes, so in due time actions to maintain key parameters within pre-established specifications can be applied. The second provides composite samples at the end of a working shift to demonstrate that valuable constituents sent to the plant went to either a final concentrate or to the tailings in a logical, expected proportion. Contrary to what many experts may claim, these two kinds of sampling requirements are incompatible and cannot be fulfilled using the same sampling systems; this is because the required samples have completely different objectives. A process control sample is an instantaneous sample with increments taken at short intervals, and the objective is to know where the process is at any given time. Excellent accuracy is not a must, however good precision is recommended since a possible process correction may need to be made. Online analysers fed with in-stream stationary cutters or other kinds of in-stream or by-stream probes can do well for such a mission. A composite sample for metallurgical accounting with increments collected over a long period of time, for which excellent accuracy and good precision are both required, must be generated by sophisticated and extremely well-maintained cross-stream sampling stations. The use of process control sampling systems to achieve good metallurgical accounting has been promoted by several manufacturers of sampling equipment around the world; it is a grave mistake that is misleading top management and a practice that should be scrutinised and preferably eliminated. Furthermore, bias tests used to prove otherwise are often based on insufficient data to draw valid conclusions; a guideline is provided.CITATION:Pitard, F F, 2014. Sampling systems for process control and metallurgical accounting, in Proceedings Sampling 2014 , pp 25–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By R Beaulieu, D Burlingame, C Hanks

The Ekati Diamond MineÖ is CanadaÆs first diamond mine and is located 300 kilometres northeast of Yellowknife in the Northwest Territories. The development of the mine supports sustainable development through the integration of environmental, economic and social considerations with the broad aim of minimising environmental impacts while maximising opportunities and benefits to northern residents and northern businesses. The environmental assessment and regulatory processes for the Ekati Diamond MineÖ were the most extensive seen in the NWT to that date; in Canada only uranium mines receive more attention. In addition to the regulatory requirements, an Environmental Agreement was negotiated with the Governments of Canada and the Northwest Territories to address environmental concerns not covered by existing legislation and regulation. Under the agreement an Independent Environmental Monitoring Agency was set up to oversee the regulatory process and implementation of the Environmental Agreement. Environmental stewardship is implemented through an Operational Environmental Management Plan, part of which includes effects monitoring programs for wildlife and aquatics where available traditional ecological and scientific knowledge are integrated to broaden our understanding of the tundra environment. A Socio-economic Agreement was concluded with the Government of the Northwest Territories to maximise employment and business benefits to the north. Voluntary and confidential Impact Benefits Agreements (IBAs) were also negotiated with four Aboriginal groups who use the area where the mine is located. The intention of the IBAs is to foster development initiatives and a partnership thereby helping to insure that benefits from the project flowed to the Aboriginal groups despite a lack of settled land claims in the region. All these were completed before commercial production in October 1998. Employment targets of 62 per cent residents of the Northwest Territories and 31 per cent Northern Aboriginal have consistently been met thereby ensuring benefits flow to residents of the Northwest Territories. In 2000, $316 million was spent to support operations at the Ekati Diamond MineÖ. Of this, 82.2 per cent of total spending and 26.6 per cent total northern spending was northern and northern Aboriginal businesses, respectively. The environmental and socio-economic monitoring results are reported annually to the responsible government agencies and potentially affected Aboriginal groups. To date, there have not been any significant adverse environmental effects documented and socio-economic targets have been met.

Jan 1, 2002

By A M. Barrett, P J. Chapman

As filtering technology improves and there is an increased focus on environmental impacts, the concept of managing fine coal rejects by filtering, mixing with coarse rejects and dry stacking them is being considered more seriously. In Queensland, there appears to be a desire from regulators to move away from wet rejects facilities towards dry-stacked facilities, resulting in a change in the risk profile for the facility.A coalminer has a site with many constraints, including limited area that is not planned to be undermined and nearby rivers that are prone to flooding. The design of a dry-stacked facility that meets the operational requirements and environmental compliance criteria is challenging in subtropical climatic settings, where there is a need to consider wet seasons with high-volume, sustained rainfall events. The impact of the rainfall is multifaceted, requiring careful surface water management to separate clean and contact water, adequate foundation preparation to limit seepage to groundwater, management of stack stability given a potentially high phreatic surface and the avoidance of potential flood zones. These design constraints were compounded by a limited area available for rejects storage that would not be undermined.This paper presents a summary of the conceptual design of a dry rejects facility, including consideration of regulatory and client requirements, provision for expansion while also considering progressive rehabilitation, diversion of clean water as much as practicable during operations and siting constraints. A step-by-step concept is presented that addresses each constraint during the life of the facility.CITATION:Barrett, A M and Chapman, P J, 2015. Conceptual design of a dry-stacked coal rejects facility in a subtropical climate, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By A L. Zawadski, B G. Putland

"This paper discusses a method to build a calibrated comminution circuit model, using historic operating data and blend information that is useful for forecasting and optimising plant performance, as well as evaluating expansion opportunities. A preferred method for building a calibrated power-based comminution model is discussed and justified based on two case studies, offering low-cost and effective strategies to utilise existing information for the maximum possible benefit.The first example is the Lefa Gold Mine located in Guinea, West Africa operating a semi-autogenous grinding (SAG) and ball milling circuit with recycle crushing (SABC). Daily blend information and operating data was utilised to build and calibrate a power-based model of the comminution circuit. The least squares regression method was used to solve the SAG mill specific energy requirement and the operating work index (Wio) for each individual ore type. The calibrated model was used to evaluate expansion strategies to sustain throughput at higher proportions of fresh ore based on the proposed life-of-mine schedule.The second example is the Ok Tedi Copper-Gold Mine in Papua New Guinea operating a SAG and ball milling circuit (SAB). The circuit limitation would often shift between the SAG mill and the ball mill due to variable ore characteristics and feed blend. Typical SAG mill relief strategies, such as recycle crushing or secondary crushing, required significant capital expenditure and the potential throughput benefit would vary depending on ore type, making economic justification difficult. Daily blend information and operating data was used to build and calibrate a power-based model of the comminution circuit to identify ore types that might benefit from higher blast intensities to increase fines content, thus relieving the SAG mill limitation and increasing overall throughput without a major capital investment.Citation:Zawadski, A L and Putland, B G, 2016. Calibrating Comminution Models Using Operating Data to Forecast and Optimise Plant Performance, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 17–26 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By A T. Spathis, M L. Lawlor-O’Neill

A methodology for the inversion of a scaled charge weight superposition model to predict peak particle velocity (PPV) has been examined. The inversion involves two steps: first simulated annealing is used to get an initial estimate of the model parameters; and second, these parameters are used as input to a quasi-Newton non-linear optimisation method, used to refine the value of the parameters. The methodology recovers the three required parameters (two charge weight scaling parameters and a time window width) and does this directly from a single production blast for a given point of interest. It has been tested on a synthetic example and recovered the input model parameters successfully in the presence of introduced noise with a coefficient of variation ranging up to ten per cent. Another test used the vibration measurements of three tunnel blasts monitored during the construction of the Citybanan tunnel in Stockholm. In this case, the three model parameters are found from one blast and for a given point of interest, and the PPV at the same point of interest is predicted for the second and third blast fired in the same vicinity as the first blast. The three blasts used different firing sequences. The predicted PPV limits use a confidence interval determined from the scatter in the peak levels obtained from the single calibration blast. The methodology was able to predict an upper bound for the PPV in 21 of the 26 tunnel blast vibrations studied. These predictions improve on a previous study involving the same model but which did not use the inversion process above. Given this reasonable success, further testing of the method on other data sets and alternative forward prediction models is recommended.CITATION:Lawlor-O’Neill, M L and Spathis, A T, 2015. An inversion method for the prediction of peak particle velocity in blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 97–108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By L Jackson, A Parbhakar-Fox, N Fox

"Characterisation of sulfide minerals (eg pyrite, sphalerite) in historic tailings can assist in determining whether there are economic benefits of reprocessing such materials using modern metallurgical practices. In addition, there are associated environmental advantages if the historic tailings are actively generating acid and metalliferous drainage (AMD). At the Old Tailings Dam (OTD), Savage River, Western Tasmania, 38 Mt of pyritic tailings were deposited from 1967 to 1982; consequently it has been recognised as an AMD source. Long-term management options considered for this site have included the establishment of either a water, hard-engineered or vegetation cover. However, due to geotechnical challenges posed and the lack of success demonstrated by previous pilot studies, these strategies have not been implemented. Instead, resolving the pyrite chemistry can allow for a first-pass assessment of whether reprocessing these tailings is a feasible option as part of a long-term management strategy for this legacy site.Tailings samples (n = 144) were collected across the OTD from up to 2 m depth from five facies (A–E), and four zones (1 to 4; defined by hydrological regime and grain size). These materials were subjected to acid-base accounting (ABA) and mineralogical evaluations to determine their geoenvironmental characteristics. Following this, 26 samples were selected for in-depth laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) investigations to evaluate pyrite chemistry across different tailings facies. The results revealed enrichment of Co and Ni in these materials. Specifically, Co content was up to 3.0 wt per cent, particularly within facies C to E, and Zones 3 and 4. Cobalt is recognised as a critical metal, therefore, reprocessing should be considered as a future rehabilitation option for the OTD, pending resource definition using established codes and practices.CITATION:Parbhakar-Fox, A, Fox, N and Jackson, L, 2016. Geometallurgical Evaluations of Mine Waste – an Example from the Old Tailings Dam, Savage River, Tasmania, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 193–204 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By R Wolff

One critical factor in open pit mining projects is the estimation of the recoverable reserves. The reason for this is that at the valuation stage there is a lack of information about future metal prices and production costs. Consequently, the estimation of the recoverable reserves needs to be done based on a fixed break-even cut-off grade (BECG), in which fixed expected metal prices and production costs are assumed throughout the operating life of the mine (OLM). In this paper, an alternative technique for estimating the recoverable reserves of an open pit mining project is presented and explained in detail. The main characteristic of this technique is that it estimates the recoverable reserves of the project using mining costs as reference: this is done due to the fact that mining costs are easier to model than metal prices. Another important characteristic of this technique is that it uses the uncertainty of the geology of the orebody, given by simulations of the deposit, to make final strategic decisions, such as the selection of the operating life of the mine and the optimal production rate, which minimise the risk of not achieving future production targets while maximising the upside potential of future rewards. As it will be shown, the final outcome of the proposed technique is the generation of a robust open pit design, that include cutbacks and ultimate pit limits, called the marginal open pit mine design (MOPMD). One characteristic of the MOPMD is that, at each production period, it will be characterised by their respective geological uncertainty, given as probability distributions of ore, waste and metal quantities, and by marginal economical project indicators, such as cut-off grades and metal prices, among others. The details follow in the paper.

Jan 1, 2006

By S J. Chen, N Jiang, Y S. Ding, F X. Li, D W. Yin, F Wang

This study assessed the deformation failure characteristics of rock-coal composites with different height ratios. Uniaxial compression tests were conducted using an acoustic emission monitoring system and XTDIC three-dimensional full-field strain measurement system. The results showed that with the increase in rock-coal height ratios, the uniaxial compressive strength of composite samples increased from 5.26 MPa to 14.61 MPa. The evolution of the deformation localisation zone of the composite samples is closely related to the initiation and propagation of the primary cracks in the coal samples. At the moment when the main fracture of the coal samples occurs, there is a large drop after the peak of the stress-strain curve of the composite samples, and the height of the rock samples increased to varying degrees, which indicated that the failure of the coal samples induced the rebound deformation of the rock samples. With the increase in rock-coal height ratios, the rebound deformation amount of the rock samples decreased from 0.042 mm to 0.008 mm, and the rebound deformation rate decreased from 0.210 per cent to 0.010 per cent. Meanwhile, the rock samples’ rebound deformation releases part of the elastic energy to act on the coal sample, further contributing to the destruction of the coal samples. Compared with single composite coal samples, the coal samples of the composite samples have much more failures. In addition, with the increase in rock-coal height ratio, the input energy density, elastic energy density, post-peak release energy density, and residual elastic energy density of the composite samples increased, the dissipation energy density decreased, and the percentage of pre-peak elastic energy density increased from 98.56 per cent to 99.86 per cent. These results revealed the deformation failure characteristics of rock-coal composite with different height ratios and provided a theoretical reference for understanding the underground dynamic rock failures.

Nov 29, 2022

By V Srinivasan, P Knights, C T. Farrelly

By 2025, with the widespread industry adoption of remote operation centres and advanced analytics, mining companies will find themselves making better, more informed decisions across the value chain. Process automation will drive significant business integration and reorganisation. Better collaboration between functions will make cross value chain optimisation a reality. Wherever possible decisions will be automated, based on analytical models and embedded in an enterprise decision management (EDM) architecture. This will take care of many of the minor day-to-day or the minute-to-minute decisions that consume operators and managers today. More flexible information technologies and architectures derived from the extensions to Web 2.0 and service oriented architecture (SOA) will solve many of the integration issues of today. The ongoing business imperatives for doing more with less people will make true collaboration with partners such as mining contractors, equipment vendors, transport providers, suppliers and maintenance contractors commonplace throughout the industry. All these organisations will be linked in and share common goals and objectives in real-time while providing visibility of internal constraints and available capability, allowing optimised decisions to be made across the extended enterprise. Humans will increasingly move to a more supervisory role and will use advanced collaboration to quickly solve complex abnormal issues that span the value chain out to the extended enterprise. The open collaboration and communication models instilled in the workforce through the widespread use of social networking technologies will drive thought leadership far beyond current æbest practiceÆ thinking. This will encourage the mining industry to extract the business value from rapidly converging fields of study such as environmental sciences, neuroscience, psychology, engineering, information technology and business finance. The future of mining will see a more uniform distribution of data savvy workers between the ages of 20 - 40, forcing a change in current operations. This group will drive the adoption of ubiquitous computing, augmented reality, presence and digital labelling. The enterprise will shift from a relatively static disparate set of functions to a digitally aware, integrated and interactive environment with information available, in context and just in time, to those who need it. The networked virtual enterprise will therefore be a reality.

Jan 1, 2008

By X Zheng, P Manton

Pebble recycle crushing circuit performance at Telfer has historically fallen significantly short of the design product P80 of 12 mm. An investigation was undertaken to evaluate the current pebble crusher circuit performance, quantify the optimum performance achievable with the existing circuit and examine the impact of pebble crusher performance on the overall grinding circuit throughput. The primary objective of this investigation was to develop an operating strategy that could consistently deliver the finest possible pebble crusher product to maximise the overall plant throughput.The pebble crusher specific energy (Wc) was proposed as a key control variable for pebble crusher operation based on the results of plant survey work. Over the range of pebble crusher specific energies encountered at Telfer, a strong linear relationship was found to exist between Wc and the crusher product size. This direct linear relationship between specific energy and crusher product size remained constant regardless of how the change in specific energy was generated, ie through changes to the crusher closed side setting (CSS), feed rate, liner profile or moisture content. Key findings for the Telfer pebble crushing circuit were: each 0.1 kWh/t change in Wc resulted in a 4.9 per cent to 6.0 per cent change in plant throughput, each 1 mm change in pebble crusher CSS resulted in a 2.2 per cent to 2.6 per cent change in plant throughput, and 0.57 tonne of new feed was displaced for each tonne of crushed pebbles recycled to the semi-autogenous grinding (SAG) mill. The presence of an existing 3000 tonne pebble stockpile between the SAG mill and pebble crushers provides an opportunity to manipulate the feed rate to the pebble crushers independently of the SAG mill pebble production rate. This flexibility, along with excess pebble crushing capacity, enables the pebble crusher specific energy to be maximised the majority of the time. Pebble crusher specific energy has subsequently been incorporated as an online crusher control measure to assist in maximising plant throughput.

Jan 1, 2009

In March 2003, Rio Tinto Coal AustraliaÆs (RTCA) new Hail Creek open cut coal mine commenced operations in the Bowen Basin. Hail Creek is a two-seam strip mining operation utilising two 90 m3 draglines and a fleet of excavators and trucks to remove the overburden. All overburden at Hail Creek is blasted prior to excavation. The mine conducts its own drill and blast operations while engaging Dyno Nobel for the provision of explosives supply and loading truck (bulk explosives vehicle û BEV) services. This arrangement was favoured over outsourcing the entire blasting function to a contractor. Subsequent to a value engineering review, the mine set about developing and implementing a blasting operation that did not rely on the need to store bulk quantities of ammonium nitrate on site. There were advantages identified in doing this, in particular the reduction of capital expenditure required and reduced exposure to a number of recently introduced security requirements. This approach also makes sense operationally. The establishment of reload facilities for the BEV close to the blasting location, where turnaround times are kept to a minimum, increases the productivity of the BEV. For this strategy to be successful the logistics of ammonium nitrate supply into the blasting operations has to be well planned and thoroughly executed. This means a robust planning and forecasting arrangement needs to be established with the supplier and transporters of the ammonium nitrate. To date, 80 million bcm of overburden has been blasted at Hail Creek and each year the quantity of overburden requiring blasting is increasing. The purpose of this paper is to present the findings of a study: evaluating the effectiveness to date of the strategy to conduct blasting operations without ammonium nitrate storage on site, and identifying whether there is a limit to which this strategy can operate after which the introduction of bulk ammonium nitrate storage facilities are necessary.

Jan 1, 2007

By Kuganathan K, Potvin Y

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: 1. a minimum filling rate of 250 ma/h, 2. a curing time of 28 days, and 3. minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998

When I was first asked to give a paper on work-life balance in the mining industry I was both excited and aware of the incongruity of my position. I have never worked in mining operations nor have I had any experience that approximates the on-site lifestyle. IÆm not really an adventurer or a traveller, I prefer writing and research to hands-on activities and IÆve never worked further than twenty minutes away from home. The perspective I offer is thus largely an objective one. I say largely since I grew up in a family where my parents work arrangements involved long-distance commuting; my dad continues to work FIFO at a coalmine in Blackwater until this day. Perhaps my tortoise-like existence is a rebellion against his flighty movements. The analysis I will be presenting today draws together a variety of sources, from member anecdotes and research on FIFO and work-life balance to the popular philosophy writings of a bald Englishman with a French name. I am speaking of the famous writer, Alain de Botton, whose television show æThe Consolations of PhilosophyÆ you may have seen on the ABC. Work-life balance is a term that gets a lot of mileage in corporate brochures and at breakfast seminars. But like many terms that get bandied around in the human resources circuit, from æteam synergyÆ to æperformance optimisationÆ, I am frequently perplexed as to what it actually means. Corporate websites are at pains to emphasise the high priority that they place on the needs of the whole person. Yet in terms of substantive content, a commitment to work-life balance often seems to translate into little more than the option to take a few morning yoga classes in exchange for working a seventy-hour week. As extended work hours have taken their toll, leading to high attrition of professionals across all industries, employers are increasingly expending resources to discover just what lies behind this buzz word. The challenge for companies is to find meaningful strategies to help employees better integrate different aspects of their lives in a new era of work, as employees are sending the message that they are not willing to play work, social life and leisure off against each other in a zero sum game.

Jan 1, 2005

By L N. Loganathan

Risk exposure in tunnel projects is extremely high due to various factors such as variability of subsurface conditions, selection of inappropriate design and tunnelling methods, improper risk assessment on adjacent surface and subsurface structures and utilities, and inadequate contractual practices. The risks in tunnelling must be borne by the contractor, designer and the owner of a tunnelling project. There have been a number of improvements in the last ten to 15 years in the manner in which tunnel projects are developed and implemented in terms of their design, construction, financing and operations. One significant improvement has been the manner in which underground conditions and their risks are being managed. Owners are less willing to transfer the full responsibility to the contractor for managing the underground conditions, although this is a familiar manner in which underground major urban projects have been previously contracted and managed. The owners of tunnel projects in Singapore have advanced the risk management process for their projects through geotechnical interpretative baseline reports (GIBRs), geotechnical data reports (GDRs) and project specifications (PSs). This paper discusses industry practice and its development as well as the application during the preparation and use in Singapore on the Deep Tunnel Sewerage System (DTSS) and the Marina Coastal Expressway (MCE) project in Singapore. The DTSS trunk sewer is 48 km and ranges from 3.3 m to 6 m finished diameter up to 50 m below the ground. The underground conditions ranged from Old Alluvium, strengths of about 1 MPa to competent Bukit Tima granite, with strengths of over 230 MPa. The total route length of the MCE is about 5 km. About 3.6 km will be constructed underground, consisting of dual five-lane carriageways. The underground construction will be cut-and-cover, and 2.6 km will be constructed about 13 m underground, and 1 km of tunnel will range from 13 m to 24 m as the tunnel passes under a 420 m wide reach of Marina Bay, whose crossing will be constructed as a two-phase cofferdam.

Jan 1, 2008

By A Manzoori, M T. Shadloo

This paper describes a CFD modelling study which was carried out to investigate possible improvements in the design of an alumina precipitator tank at the Jajarm plant of Iran Alumina Company. In particular, the tank has an impeller located very close to the tank bottom, such that it quickly becomes covered with settled solids after a shut-down of the agitator, making it difficult to restart. A CFD model was firstly set up in which the existing design was evaluated in terms of flow pattern, off-bottom suspension and distribution of solids, and power consumption. Further simulations were then carried out to test alternative designs, leading to a recommended design, which maintains good mixing, with the same power consumption and without the use of a low-clearance impeller.

Jan 1, 2006