Search Documents

By G. M. Ritcey, A. W. Ashbrook, E. G. Joe

Solvent-in-pulp extraction of uranium from acid leach slurries of flotation concentrates is described. Solvent extraction was carried out in a 10 in. diam pulsed-plate column. The extractant was a 0.1 M tertiary amine (General Mills Alamine 336) in a kerosene diluent containing isodecanol as an emulsion suppressor and third phase inhibitor. In pilot plant operation at the Beaverlodge mill of Eldorado Mining and Refining, Ltd., slurry feeds containing up to 35% solids were processed at a throughput rate of 13.5 tpd of dry feed. Uranium extraction obtained was as high as 98%. Amine losses to the raffinate were approximately 0.07 lb amine per ton of original dry feed. The Beaverlodge Mill of Eldorado Mining and Refining employs a carbonate leach for the extraction of uranium from the ore.',' Prior to carbonate leaching sulphides are removed by flotation to reduce reagent consumption. This flotation concentrate containing some uranium is then leached with sulfuric acid, filtered, and the uranium precipitated with magnesium hydroxide. The precipitate is then returned to the carbonate leach circuit. Although the tonnage of flotation concentrate treated by acid leaching is low, reagent costs are relatively high. Also maintenance costs on the acid leach filtration circuit were beginning to show significant increases. The choice of solvent extraction-in-pulp as an alternative to the present circuit was influenced by the following factors: 1) elimination of acid pulp filtration, 2) increase in overall recovery because of soluble loss elimination, 3) reduction of reagent cost (mill sodium carbonate solutions are used as strip), and 4) production of higher purity precipitate at the mill site. Because a solvent-in-pulp process would be difficult to test on a bench-scale, the Eldorado experience in the use of pulse columns,3-5 mixer-settlers,6 and solvent-in-pulp operations in particular7 was applied directly to the initial pilot plant carried out during the summer of 1965 and followed by the second pilot plant in 1966. The latter work, which is presented in this paper, determined the following factors for anticipated scale-up to plant production: 1) overall uranium recovery by this process, 2) tonnage throughput expected, and 3) solvent losses anticipated for the full-scale plant. The equipment used consisted of a 10 in. diam extraction pulse column and three mixer-settlers for scrubbing, stripping, and acid equilibration. All equipment was designed by Eldorado and much of the pilot plant was built at the mill site. PROCESS CHEMISTRY Feed to the acid leach plant consists of a sulphide flotation1,2 concentrate containing mainly pyrite, uranium and graphite, with a particle size of 90%

Jan 1, 1968

By Donald W. Gentry

The recently established SME-AIME Education Board has completed its first full year of operation, and its six constituent committees-Accreditation, Career Guidance, Continuing Education, Educational Statistics, and Scholarship-have been extremely active in identifying and initiating programs to serve the educational needs of the Society of Mining Engineers and its members. The Continuing Education Committee-primarily concerned with the needs and problems associated with providing a continuing education program for SME members-is responsible for: (1) determining the need for short course offerings; (2) developing needed courses, along with new means and opportunities of presentation; and (3) scheduling and evaluating course presentation. In response to this charge, the committee has sponsored two short courses at the SME-AIME Fall Meeting in St. Louis and three short courses at the AIME Annual Meeting in Denver. Its major effort, however, has been directed toward the 1978 SME-AIME Fall Meeting to be held in Orlando, Fla., where 18 days of short-course instruction have been scheduled. A portion of these courses will be presented prior to the meeting, with the remainder to be presented in Nassau, Bahamas, immediately following the meeting.

Jan 7, 1978

By Eugene N. Cameron

Pegmatites of these areas have become important sources of beryl and lepidolite and have yielded cassiterite, columbite-tantalite, and other minerals. Examination of about 60 of these pegmatites leads the author to question the opinion of earlier investigators that the concentrations of beryl, lepidolite, and columbite-tantalite found have mostly formed by hydrothermal or pneumatolytic replacement of previously formed quartz-feldspar pegmatites. The author concludes, on the contrary, that present knowledge of the occurrence of minerals in zoned pegmatites can be applied to prospecting and mining of pegmatite deposits in these two areas of South West Africa. PEGMATITES occur in abundance in certain areas of South West Africa and in adjacent parts of northern Cape Province in the Union of South Africa. Some of the pegmatite deposits were prospected before World War I, and intermittent mining was done during the period between the two World Wars. The deposits of the Jooste lithium mines became an important source of lepidolite, and beryl, columbite-tantalite, wolframite, and other minerals were produced. Since World War II prospecting and mining have been carried on vigorously, with the result that South West Africa produced nearly 3000 tons of beryl during 1949 through 1953, together with more than 40,000 tons of lithium minerals, chiefly lepidolite and petalite. Small amounts of tantalite, columbite, and other minerals have also been produced during the postwar period. Most of this mineral production has come from two pegmatite areas roughly outlined in Fig. 1. One is the Karibib-Omaruru area of north central South West Africa. The second is the northeastern part of the Orange River pegmatite area, which extends into adjacent parts of Namaqualand, in northern Cape Province of the Union of South Africa. The writer visited the two pegmatite areas in July 1951. The visit was brief. but it gave an opportunity to compare some of the' pegmatites of these areas with those studied and described in detail by many investigators in the U. S., Brazil, and Canada during and since World War 11.'-l' The writer has attempted to determine, in a preliminary way, whether the concepts of internal structure and distribution of minerals in pegmatite bodies developed out of these studies are applicable to prospecting and exploration of pegmatites in South West Africa. Previous Work In an important series of papers (1929 to 1942) T. W. Gevers, H. I?. Frommurze, S. H. Haughton, G. K. Joubert, and other geologists of the Geological Survey of South Africa described and discussed the pegmatites of the two areas.*-" These works are the principal sources of information on the pegmatite mineral deposits of South West Africa. The investigations showed that in the two areas pegmatites are profusely distributed in pre-Cambrian rocks. These rocks are meta-igneous and metasedimentary units that have been folded and subsequently invaded by younger pre-Cambrian granites and by other igneous rocks. The pegmatites are considered to be genetically related to the pre-Cambrian granites. Pegmatites occur in the granite bodies themselves but are most abundant in the surrounding metamor-phic rocks, a pattern repeated in many pegmatite districts of the world. The origin of the pegmatites and the factors controlling the occurrence of mineral deposits in them were discussed at length by Gevers and Frommurze (1929)" and later by Gevers 14, 15 pp. 41-51, Ref.

Jan 1, 1956

By J. W. Harshbarger, E. L. Montgomery

The region of metallic ore deposits in northern Chile, southern Peru, western Bolivia, and northwestern Argentina occurs in arid zones at altitudes as high as 6 km (19,700 ft). Because surface water supplies are meager, new mines require unexploited sources of water. Prolific ground water aquifers occur in salar basins in this region of the Andean Highlands. Exploration water wells have been constructed and aquifer characteristics have been tested in eight salar basins. Results indicate ground water quality is good. Aquifer transmissivity and storage computed from results of pumping tests indicate maximum capacities of more than 170 L/sec (2700 gpm) for individual production water wells. Results of investigations conducted by the authors demonstrate that ground water reservoirs in the Andean Highlands comprise a source of large quantities of water for the mineral industry.

Jan 1, 1986

By Charles Will Wright

THE economy as well as the living standards of a country depends largely upon adequate supplies of raw materials at reasonable prices. Geological and climatic conditions responsible for the occurrence of commercial minerals and the growth of raw agricultural and forest products are so varied in different parts of the world that no country can be self-sufficient. The world is rapidly shrinking because of improvement in transportation facilities, but populations are steadily increasing and so are the needs for a greater production of raw materials and for their more equitable distribution. Too many barriers between nations prevent free access to the main sources of supply of the raw materials vital to neighboring nations and it is just such barriers that are often the cause of friction and even war. The International Trade Organization is doing a commendable job in helping to. break down barriers and to reduce friction, and we should now find ways to facilitate access to these sources of supply and encourage more efficient and greater production of the raw materials so urgently needed throughout the world. This cannot be done by individual selfish governmental agencies, influenced as they are by politics, nor by socialistic governments attempting to nationalize industries. It can be done efficiently only by the free individual through private enterprise properly protected against adverse governmental action. This protection can be supplied by the World Bank.

Jan 1, 1948

By John B. Pearse

IN view of the great importance of accurate knowledge respecting the chemistry of iron and steel, as related to their physical properties, I come before you with a paper showing the great mass of work which has been heretofore done on the subject. I have tabulated the more important data I bring at this time, so as to draw out the results clearly. This information is accessible to all who will seek for it. I have made it the basis of my own practice throughout, and such knowledge is undoubtedly the only foundation, for the successful practice of metallurgy. As is well known the ordnance corps of our army, after 1841, made exhaustive experiments on the properties of cast-iron. The investigations were undertaken in order to obtain necessary information on the reorganization of the corps. I wish to call your attention to the results obtained by a comparison of the chemical and physical properties of cast-iron for guns, to describe certain characteristic peculiarities of steel, and to give a brief history of the chemical work relating to carbon in iron. The Reports on Experiments on the Strength and other Properties of Metals for Cannon, published by H. Carey Baird, Philadelphia,

Jan 1, 1876

By John B. Pearse

In view of the great importance of accurate knowledge respecting the chemistry of iron and steel, as related to their physical properties, I come before you with a paper showing the great mass of work which has been heretofore done on the subject. I have tabulated the more important data I bring at this time, so as to draw out the results clearly. This information is accessible to all who will seek for it. I have made it the basis of my own practice throughout, and such knowledge is undoubtedly the only foundation for the successful practice of metallurgy. As is well known the ordnance corps of our army, after 1841, made exhaustive experiments on the properties of cast-iron. The investigations were undertaken in order to obtain necessary information on the reorganization of the corps. I wish to call your attention to the results obtained by a comparison of the chemical and physical properties of cast-iron for guns, to describe certain characteristic peculiarities of steel, and to give a brief history of the chemical work relating to carbon in iron. The Reports on Experiments on the Strength and other Properties of Metals for Cannon, published by H. Carey Baird, Philadelphia,

By R. J. Reynik

A semiempirial small flunctation theory of diff- sion in liquids is presented, which employs a fluctuation energy assumed quadratic for a small atomic or molecular displacement and Einstein's random-iralh model. The resulting diffusion equation is given by In these equations. D is the diffusivity, is the average liquid shite coordination number (at interatomic distance d. cm. T is the absolute temperature, xu. em, is (the diffusive displacement. K, is the quadratic fluctuation energy force constant, and rg, cm, are the radii oj diffusing atoms A and B, respectively. The quantities Xn and K are calculated from the computer-filled values of the slope and intercept. respectively. The radius of self-diffusing atom or radii and of diffusing atoms A and B are eta United and compared with values reported in the literature.. The predicted linear variation of diffusivity with. It tempera lure htm been observed in approximately thirty-iire metallic liquid systems, and in over seventy-fiee other liquid systems, including the organic .alcohols, liquified inert gases, and the molten salts, ALTHOUGH the average density within a macroscopic volume element of liquid is constant for fixed total number of atoms. pressure. and temperature, there exist microscopic: density fluctuations within the respective volume element. As such the microscopic volume available to an atom and its Z first nearest neighbors at any instant of time fluctuates above and below the average volume available to these atoms. If one assumes that liquid state atoms vibrate as in a solid. and further postulates that the mean position of any atom in the liquid state is not stationary. but shifts during every .vibration a distance 0 5 j 5 xo. then every atom in the liquid state continuously undergoes diffusive displacements which vary in the range 0 5 j 5 ro. Mathematically. for a binary liquid system consisting of atcrms A and B. the maximum diffusive displacement. .YO, is defined by the equation: where d is the average liquid state interatomic distance at specified liquid state coordination number Z. and v~ \ and vg are the effective radii of diffusing atoms A and B: respectively. For self-diffusion. r^ equals rg , and Eq. [I.] reduces to: It is interesting to note that Eq. [l] or [2] can be used to compute the radii of the diffusing atoms, provided one had an experimental evaluation of xo. As such. the computed radii could be compared with metallic or crystallographic ionic radii to ascerlain the electronic character of the diffusing atoms. Thus it is proposed that in the liquid state the n~otion of an atom relative to its original equilibrium position of oscillation represents the thermal vibration of any atom and its Z first nearest neighbors. while the small and variable displacements. 0 5 1 5 xc,. of the centers of oscillation represent the complex diffusive motions of the atoms at constant temperature and pressure. This is consistent with data obtained from slow neutron scattering by liquids1 ' and resembles an itinerant oscillator model of the liquid state.'" It is further postulated that the atomic displacements characterizing the liquid state diffusion process are essentially a random-walk process. As such. it nlay be described by Einstein's equation:' where D is the diffusivity. sq cm sec-'. j2 is the mean square value of the diffusive displacement. and i> is the frequency of density fluctuations giving rise to diffusion. FORMULATION OF DIFFUSION EQUATION The effective spherical volume occupied by an atom, as a consequence of a microscopic density fluctuation which enlarges the volume available to any atom, exceeds its average liquid state atomic volume by an amount: where AV is the enlarged spherical volume, v is the radius of the diffusing atom. and j is the elementary displacement distance from the original center of oscillation of the vibrating atom to a new center of oscillation position. For small atomic displacements. where c is a constant whose value depends upon the assumed geometry of the enlarged volume. For a spherical increase in volume, c equals 4nr2. Following the treatment of Furthl' and ~walin." assuming the enlarged volu~nes AL7 for the diffusing atoms are distributed in a continuunl. the probability of finding a fluctuation in the size range 0 5 j 5 xo defined by Where c includes the geometric constant cl and Eij) is the fluctuation energy causing the volume change. But the proposed model assumes all the Z first nearest-neighbor atoms are centers of oscillation. and hence the probability that any of these atoms is adjacent to a fluctuation of magnitude 05j5xo is unity. Thus:

Jan 1, 1970

By Hiroshi Kato, Shin’ichi Nagashima, Hiroshi Takechi

The preferred orientations detleloped during cold rolling, annealing, and hot rolling of low-carbon steel sheets have been investigated by means of an inverse pole figure technique. And X-ray line profile meas-urerrlents were made for the study of the factor which causes the textural changes between cold-rolled and recrystallized sheets. From ND (sheet normal divection) and RD (rolling direction) inverse Pole figures tlze axis detisity change with increasing cold reduction was measured and the Preferred orientations were analyzed. These results can be explained by crystal rotation due to slip during rolling deformation. The ND axis density change during annealing of cold-rollitig sheets is contrary to the change observed in the case of rolling. It was found that the orientation dependency of stored strain energy resulting from cold rolling apparently corresponds to the textural changes during recrystallization. The texture in hot-rolled sheets was found to be influenced by finishing tenlperatltre. In a sheet kol-rolled below the Ar, temperature a significant differernce in texture between the surface and central layers was obtained, the former having {hkl}(111} and {110 )(uvw) orientations and the latter having {pqr}( 110) orientation. A large number of investigations1 6 have been made on the textures of iron and low-carbon steel sheets, and, since it was shown7 13 that preferred orientations are closely related to deep drawability of steel sheets, studies14" 7 on the influence of production processes upon textures have been made from the standpoint of industrial interest. Generally, the textures in low-carbon steel sheets have several components of preferred orientations, but the overlapping of poles makes it difficult to analyze texture quantitatively from pole figures. On the other hand, an inverse pole figure directly expresses quantitative values of components of preferred orientations as the density of a certain sample axis with respect to the crystallite coordinates. Such a texture representation is desirable for a study of deep drawability. The purpose of the present work is to use both inverse and conventional pole figures, with emphasis on the former, to clar~fy the textural changes ~n low-carbon steel sheets by the production processes of hot rolling, cold rolling, and annealing. And the factor causing the textural changes during annealing is studied using an X-ray diffraction line profile technique. EXPERIMENTAL PROCEDURE Sheet specimens for study of cold rolling and annealing textures were taken from a hot-rolled strip of rimmed steel 2.7 mm thick. The chemical composition is shown in Table I. Although the study of cold-rolling textures requires a suitable material with random orientation, it is difficult to produce a perfect random one. But the used specimens, obtained from the hot-rolled strip with a finishing temperature higher than Ar3, were nearly random, such as shown in Fig. 15. These were cold-rolled to various reductions by a 4-high rolling mill with 150-mm-diam work rolls and 300-mm-diam backup rolls. The influence of hot-rolling conditions such as finishing and coiling temperatures on textures of hot-rolled strips was studied. The chemical compositions of these hot coils are given in Table I1 and the hot-rolling conditions are given in Table 111. inverse Pole ~i~ure -~easurement. Two methods for determining inverse pole figures with high precision have been proposed. The first, by Jetter et a1.,18 consists of obtaining mean densities of divided regions in a unit stereographic triangle by solving simultaneous linear equations to approximate the integral relation between conventional and inverse pole figures. The second, proposed by ~oe'~-'~ and Bunge,22'23 consists of determining an expanded series of spherical surface harmonics which express axis densities from several sets of pole distribution data. Both methods require laborious numerical calculations which make them unsuitable for practical use. However, the axis densities of the locations corresponding to low Miller indices in a unit stereographic triangle can be obtained

Jan 1, 1969

By Kurt Kennedy

A method is described by which three elements can be condensed simirltaneously on a common substrate in such a way that the composition varies with position on the substrate. Almost all possible combinations of three solid elements can be formed in a single evaporation. The three elements are heated by magnetically deflected electron beams. The alloys and cornpounds formed by this method generally correspond to those trade by other methods; however, many exceptions exist. Simple symmetric crystallographic phases tend to form in preference to more complex phases. The Nb-Sn. Cr-Fe-Nt, and other systems of alloys made by this method will be discussed. Phases that form very slowly, such as the o phase in Cr-Fe alloys, may be formed rapidly by this method when certain substrate temperatures are used. STUDYING all the mixtures and compounds of two or more elements by the preparation of individual samples forces the investigator to make sampling sufficiently close together so that the properties of the intermediate compositions can be inferred. A completely unknown system will require a dis c our aging ly large number of preparations in order to fully know all its properties. For the purpose of expediting this type of investigation, methods have been devised to prepare samples that have a continuous variation in composition over some predefined area. The code-position of two elements onto suitable substrates has been used to produce alloys or compounds that have variable compositions depending on their positions on the substrates Composition gradients have been formed by depositing a wedge-shaped layer of one element and then depositing a second wedge-shaped layer on top of it such that the total film thickness is kept constant. Concentration equilibrium perpendicular to the surface is then established by annealing.4 This paper describes a method for the simultaneous condensation of three volatile components on a substrate such that there is a regular variation of composition with position on the substrate. The arrangement of the evaporation sources and the substrate is shown schematically in Fig. 1. Materials to be evaporated are placed in three water-cooled crucibles located at the corners of a 10-in. equilateral triangle. Electron beams from cathodes located below the crucibles are bent 180 deg by magnetic fields and focused on the material to be evaporated. The cathodes are connected in parallel to a constant-current 12-kv power supply. The distribution of emission current from each cathode is controlled by filament temperature. When materials that sublime are to be evaporated, the electron beam is deflected by an auxiliary ac magnetic field so that the beam moves over the surface of the evaporating material rather than digging a hole in one spot. The substrate is a 10-in. triangle of 2-mil stainless steel or molybdenum which is stretched against a slightly curved heat sink by a frame as shown in Fig. 2. This frame and heat sink are located so that each corner is directly above an evaporation source. The heat sink has three radiant heaters at each corner that can be separately controlled permitting the

Jan 1, 1967

By Cyril Stanley Smith

For many years sulphur and its congeners selenium and tellurium have been regarded as very harmful elements in copper and copper-rich alloys. Like many similar prejudices, this has been found to be partly wrong. All three of these elements actually have no great effect on the working properties of copper and its alloys, and are desirable additions in that they considerably enhance the machinability of alloys in which they are present. Because of their possible commercial importance, a study of the machinability and other properties of the pure binary alloys was made, as described in this paper, and the effect of selenium on a large number of copper alloys was determined. The current opinion regarding the deleterious effects of elements in this group undoubtedly arose because of occasional failures of tough-pitch copper containing unusually high tellurium, and because of the well-known fact that sulphur causes spewing and unsoundness in tough-pitch copper. Siebe,1 also Deretchey and Margolina,2 studied the effect of sulphur on copper and showed that in the absence of oxygen it was present in the form of copper sulphide, which was less harmful to the properties than an equivalent amount of copper oxide. No data have been published on selenium and tellurium, although the statement is often made, following Eggleston,3 that tellurium makes copper hot-short. Copper specifications call for only traces of these elements. Skowronski and Mosher4 give data on the effect of selenium and tellurium on the conductivity of tough-pitch copper. In private communication Mr. Skowronski says that the samples were hot-forged from small castings and drawn to 0.081 in. diameter, but it should not be inferred from this that these elements are harmless to the working properties of wirebars and commercial shapes. Constitution and Microstructure Constitution.—Sulphur, selenium and tellurium exist in their alloys with copper in the form of copper sulphide, selenide or telluride. These compounds are practically insoluble in the solid state and possess limited

Jan 1, 1938

By Cyril Stanley Smith

For many years sulphur and its congeners selenium and tellurium have been regarded as very harmful elements in copper and copper-rich alloys. Like many similar prejudices, this has been found to be partly wrong. All three of these elements actually have no great effect on the working properties of copper and its alloys, and are desirable additions in that they considerably enhance the machinability of alloys in which they are present. Because of their possible commercial importance, a study of the machinability and other properties of the pure binary alloys was made, as described in this paper, and the effect of selenium on a large number of copper alloys was determined. The current opinion regarding the deleterious effects of elements in this group undoubtedly arose because of occasional failures of tough-pitch copper containing unusually high tellurium, and because of the well-known fact that sulphur causes spewing and unsoundness in tough-pitch copper. Siebe,1 also Deretchey and Margolina,2 studied the effect of sulphur on copper and showed that in the absence of oxygen it was present in the form of copper sulphide, which was less harmful to the properties than an equivalent amount of copper oxide. No data have been published on selenium and tellurium, although the statement is often made, following Eggleston,3 that tellurium makes copper hot-short. Copper specifications call for only traces of these elements. Skowronski and Mosher4 give data on the effect of selenium and tellurium on the conductivity of tough-pitch copper. In private communication Mr. Skowronski says that the samples were hot-forged from small castings and drawn to 0.081 in. diameter, but it should not be inferred from this that these elements are harmless to the working properties of wirebars and commercial shapes. Constitution and Microstructure Constitution.—Sulphur, selenium and tellurium exist in their alloys with copper in the form of copper sulphide, selenide or telluride. These compounds are practically insoluble in the solid state and possess limited

Jan 1, 1938

By J. F. Fidiam, T. F. Ford, A. G. Loomis

It is only within the past 10 years that serious attempt appears to have been made to improve rotary drilling fluids by the application of the principles of colloid chemistry, although the use of chemicals to control the rheological properties of clay slips has long been known in the ceramic industry. The main difficulty apparently lay in the lack of a complete analysis of all of the functions of a drilling fluid in the drilling of the well, together with the lack of adequate consideration of how colloid science could be applied to secure these ends, and particularly how apparent antithetical properties of the fluid could be compromised. Thus one analvsisl of the many requirements of a drilling fluid proved conclusively that the viscosity should be low, in order that cuttings and entrained gas might be eliminated effi-ciently in the settling ditch, while the loss in carrying capacity accompanying low viscosity could be regained by increasing either the density of the mud or the upward velocity of the mud stream in the annular space of the well, and the danger of sticking of the drill stem due to rapid settling in case of enforced suspension of drilling operations could be eliminated by enhancing the thixotropic properties of the fluid. The desired properties of the drilling fluid having thus been established, it was a natural step to treat the fluid with vis-cosity-reducing chemicals, such as salts of weak organic acidsl for example, sodium tannate or gallate—and to adjust the pH to the alkaline side to such a degree of thixo-tropy as would give low viscosity and low yield point under the conditions of flow prevailing in the settling ditch, but rapid gelation and high yield point when quiescent in the annular space during shutdowns. In fact, flow in the settling ditch should be just short of turbulent while flow in the well, together with the flow of mud past the cuttings, is practically always turbulent. The use of chemicals other than those mentioned, such as Calgon (sodium hexametaphosphate) and certain other phosphates together with sodium tannate, has now become standard practice and it is the consensus that this method of treatment has proved to be an important step in the development of the art of drilling oil wells. It is safe to assume that the application of colloid chemical principles can also help in solving other outstanding problems of drilling fluids, such as the development of cheaper and more efficient viscosity reducers ; the development of chemicals that do not lose their effectiveness in a short time during drilling operations; the finding of chemicals to preserve the plastering properties of muds when concentrated brines are encountered or in drilling through salt beds; improvement in the plastering properties of poor muds by further defloc-culation, and, conversely, the prevention of excessive deflocculation of certain marine shales sometimes encountered; the preparation of muds suitable for the successful drilling of heaving shale formations; the finding 0f chemicals to treat the mud to prevent or to diminish lost circulation; the development 0f muds that will not impair 6

Jan 1, 1941

By T. F. Ford, J. F. Fidiam, A. G. Loomis

It is only within the past 10 years that serious attempt appears to have been made to improve rotary drilling fluids by the application of the principles of colloid chemistry, although the use of chemicals to control the rheological properties of clay slips has long been known in the ceramic industry. The main difficulty apparently lay in the lack of a complete analysis of all of the functions of a drilling fluid in the drilling of the well, together with the lack of adequate consideration of how colloid science could be applied to secure these ends, and particularly how apparent antithetical properties of the fluid could be compromised. Thus one analvsisl of the many requirements of a drilling fluid proved conclusively that the viscosity should be low, in order that cuttings and entrained gas might be eliminated effi-ciently in the settling ditch, while the loss in carrying capacity accompanying low viscosity could be regained by increasing either the density of the mud or the upward velocity of the mud stream in the annular space of the well, and the danger of sticking of the drill stem due to rapid settling in case of enforced suspension of drilling operations could be eliminated by enhancing the thixotropic properties of the fluid. The desired properties of the drilling fluid having thus been established, it was a natural step to treat the fluid with vis-cosity-reducing chemicals, such as salts of weak organic acidsl for example, sodium tannate or gallate—and to adjust the pH to the alkaline side to such a degree of thixo-tropy as would give low viscosity and low yield point under the conditions of flow prevailing in the settling ditch, but rapid gelation and high yield point when quiescent in the annular space during shutdowns. In fact, flow in the settling ditch should be just short of turbulent while flow in the well, together with the flow of mud past the cuttings, is practically always turbulent. The use of chemicals other than those mentioned, such as Calgon (sodium hexametaphosphate) and certain other phosphates together with sodium tannate, has now become standard practice and it is the consensus that this method of treatment has proved to be an important step in the development of the art of drilling oil wells. It is safe to assume that the application of colloid chemical principles can also help in solving other outstanding problems of drilling fluids, such as the development of cheaper and more efficient viscosity reducers ; the development of chemicals that do not lose their effectiveness in a short time during drilling operations; the finding of chemicals to preserve the plastering properties of muds when concentrated brines are encountered or in drilling through salt beds; improvement in the plastering properties of poor muds by further defloc-culation, and, conversely, the prevention of excessive deflocculation of certain marine shales sometimes encountered; the preparation of muds suitable for the successful drilling of heaving shale formations; the finding 0f chemicals to treat the mud to prevent or to diminish lost circulation; the development 0f muds that will not impair 6

Jan 1, 1941

By E. M. MacKevett

The only source of uranium ore in Alaska that has been mined commercially is the Ross-Adams de- posit, a gently inclined, fusiform orebody in alkali granite in which uranothorite and uranoan thorianlte are the chief ore minerals. In mode of occurrence, apparent genetic association with the granite, and to a lesser extent in mineralogy, this type of deposit is uncommon. The mine is in the southern part of Prince of Wales Island (Fig. 1) at an altitude of about 950 ft on the southeast flank of Bokan Mountain. A steep unpaved road 1 ¾ miles long leads to the dock on the West Arm of Kendrick Bay, which can be reached by boat or seaplane from Ketchikan, some 35 miles to the northeast.

Jan 9, 1959

By R. J. Brison, W. C. Bleimeister

The International Salt Company has long been interested in finding an efficient process for the removal of impurities from rock salt, and particularly from the rock salt produced at the Detroit mine. Methods which have been used previously at the Detroit mine included both hand sorting and differential crushing in a Bradford breaker with rejection of the oversize. Neither of these methods was adequately effective. The development of a new process for removal of impurities from rock salt has been described in the preceding article." Basically, the process consists of exposure of crude rock salt to radiant heating which selectively heats the impure particles. Subsequently the heated particles are removed by adhesion to a heat sensitive-coating on a conveyor belt. This method was found to be effective in improving both the quality and appearance of rock salt by the rejection of the dark, impure particles.

Jan 8, 1960

By H. H. Hausner, H. S. Kalish

IN recent years zirconium and beryllium have become of great interest because of their special properties. Zirconium is known for its remarkable ability to absorb the gases oxygen, nitrogen and hydrogen, has extensive use as a getter in electron tubes and has indeed become the primary metal in the manufacture of photoflash bulbs. Beryllium is of interest because it is light metal and as such could supplement aluminum and magnesium in light metal applications. The late development of zirconium ductile at room temperature produced by both the iodide and calcium reduction methods has stimulated frequent articles on this metal in the recent literature. Beryllium is so closely akin to zirconium crystall-ographically that some investigators are of the opinion that beryllium should be ductile at room temperature if it were pure enough. The crystallographic relationship of beryllium and zirconium, the interest created in Be-Zr alloys where the zirconium is believed to function as a remover of solid solution gas in beryllium and thus increase the ductility of the beryllium rich alloy, and the amenability of these metals to powder metallurgy methods stimulated this approach to an investigation of the system Be-Zr. Preliminary work showed that a zirconium compact melted when pressed in contact with a beryllium compact and sintered at 1250°C, without any apparent final bond between the two. A search of the literature revealed nothing pertinent about the Zr-Be system or about any zirconium - beryllium alloys. In 1936 Misch³ vaguely identified the compound ZrBe2 and reported that it has a deformed cubic structure. Two patents," , were issued to Mach-lett Laboratories in 1943 and in 1946 regarding the addition of small amounts of zirconium to beryllium in order to improve the ductility of beryllium so that it may better be used for X ray windows. In considering the alloy formation of beryllium with other metals Raynor thought it unlikely that zirconium would have any solid solubility in beryllium. From this indefinite information nothing could be ascertained about the possible use of Zr-Be alloys or the use of these metals intimately. A brief preliminary study of the system Zr-Be by powder metallurgy methods was undertaken to provide regions for more intense studies of Zr-Be alloys and as a guide to a formal phase diagram determination. The investigation described in the following pages was completed in less than three weeks. The usefulness of this rapid method to facilitate phase diagram studies and new alloy investigations will be shown. Materials and Procedure Zirconium powder was produced from crystal bar stock of high purity supplied by Foote Mineral Co. The crystal bar was converted to hydride at 730°C, crushed, and the hydride decomposed in purified argon at 850°C. 60 pct of the powder passed through a 325 mesh screen, 40 pct of the powder was —140 mesh, +325 mesh and the average particle size of the total was 8 to 12 microns. The beryllium powder was used as re-

Jan 1, 1951

By P. W. Bridgman

IT is characteristic of most scientific investigators that they are not satisfied with the discovery of new facts, no matter how curious or unexpected, but that along with the factual discovery there is a constant effort to understand It appears that. one's interest in, and satisfaction with, the discovery of an array of news experimental facts is enormously increased if one has at the same time a theory or hypothesis guiding one's expectation of what sort of new experimental discovery may lie around the corner Conversely, as a theoretical physicist one's satisfaction with his theory is greatly enhanced if along with the development of the theory can go the discovery of new experimental facts, confirming or perhaps modifying the theory as it grows Of course, there have been long and stretches in the history of physics in which new data of unquestioned ultimate importance ham e piled up, without much inspiration or illumination in the way of understanding For 50 years spectroscopy had such an and history, but how irksome this was felt to be is plainly shown by the almost audible relief that greeted the first success by Bohr in injecting understanding into the situation, and by the fresh rush of experimenters into this field when the prospect of understanding had once been offered The investigations in the field of high pressure, which have occupied me for a long time,1 until the last few years have been in very much the Same sort of situation as spectroscopy before the advent of Bohr A great many kids, of data were collected for a great many solid and liquid substances, and there could be no question of the importance of these data, because the uniform change of dimensions produced by hydrostatic pressure is perhaps the simplest conceivable type of alteration to which a body can be subjected But except for a few isolated flashes, there was no theoretical illumination, so that it had to be to a large extent the enthusiasm of the collector that kept me going However, within the last few years the wave-mechanics theory of solids has progressed so rapidly that

Jan 1, 1938

By C. J. Rodgers

The present day success of gravel packs to prevent or retard the migration of unconsolidated sands into the well bore is due to: (I) the use of a saline or non-aqueous, nonsolids drill fluid, (2) proper preparation of the well bore prior to gravel packing, and (3) pressure placement of the gravel. The experience gained from the "pressure pack" method of gravel packing indicates that sand-free fluid production can be maintained for a length of time sufficient to make the operation economically attractive. Data pertaining to the first 15 wells so completed by Gulf indicate that for each dollar spent to effect the completion, there will be a return of more than $2.92. The pressure pack technique of gravel packing is essentially the placing of gravel in and adjacent to the producing formations. This is done with fluid pressure and by the use of a drill fluid that will permit partial or complete loss of returns to the formation during placement. This technique was first intentionally used by Gulf in May, 1950, and since that time has been applied in more than 90 wells. Other advantages claimed for this type of completion are that the pressure placement of the gravel has a scouring effect on the casing perforations, that additional drainage channels to the well bore are created, and that the possibility of shifting of the formations adjacent to the casing is minimized and possibly prevented. During the past few years, the use of gravel to prevent or retard the migration of unconsolidated sands into the well bore has met with a favorable degree of success. Numerous methods and techniques of "gravel packing" have been used, each having its own relative merits, and with varying results. M. L. Cashion1 in 1939 ably reviewed the history of gravel packing to that time. As stated in his paper, ". .. the idea of gravel packing wells is not new." During the period 1939 to 1949, very little if any progress or change in technique in this type of completion was made. However, it was noted in some cases that during the placement of gravel, if there was a loss of drill fluid to the formation, there was a corresponding loss of gravel to the formation. Also, it was noted that in those gravel-packed completions (opposite casing perforations) that "sanded up," there was found to be an absence of gravel in the annular space between the liner and casing, although gravel had previously been placed in this space and no gravel had been removed from the well at the surface. These findings resulted in the placement of gravel with fluid pressure and by the use of a drill fluid that would permit partial or complete loss of returns to the formation during placement. Pressure placement of gravel became an accepted practice in late 1949 and early 1950. Another fact brought to light that has contributed to the current success of gravel pack completions is that drilling fluids containing solids will to some extent cause plugging of the screening medium or blocking of the producing section. The removal of these solids by chemical action, mechanical action, or a combination of the

Jan 1, 1955

By T. A. Rickard

The Cripple Creek district occupies a cluster of foot-hills on the south side of Pike's Peak and is a portion of an extensive, though uneven, plateau which unites the eastern range of the Rocky mountains with the Sangre de Cristo. It is essentially a small volcanic area, of about 20 square miles, amid the granite of the Front range. But though, when regarded as a rich mining district, it may be considered as an isolated area,* yet, geologically, it is, as Whitman Cross has pointed out, only an outlying portion of a much larger volcanic region, which stretches to the south and west, around Silver Cliff and the Rosita hills, forming the picturesque country cut by the deep cañons of the Arkansas river and its tributaries. The mines are situated amid a volcanic complex, consisting of tuffs and breccias which have been penetrated by an extensive system of dikes and other intrusive masses. The prevailing formation is an andesite breccia, which lies upon the worn surface of the granite and fills the deep basin around a volcanic vent. The breccia, since its deposition, has been broken into by several eruptions of phonolite and, later still, by a series of thin dikes of basalt and other allied rocks of a highly basic composition. The successive sedimentary formatione which, elsewhere in Colorado, lie upon the basal granite, are not represented in the district; whatever sediments were laid down before the volcanic period must have been removed by erosion, and there is very little evidence which affords a datum-line whereby the geological age of the volcanic eruptions can be determined. Whit-

Jan 1, 1901