Search Documents

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,' Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o's. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze's (and McAdam's) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By G. Caetani, E. Burt

Jan 1, 1907

By William Campbell

The structure of iron and steel, though the object of so much study and research for the past 25 years, is by no means thoroughly understood. In the first place, we have three or more distinct iron-carbon thermal diagrams, each with its own supporters, and each representing a theory of the structure and constitution of cast-iron. In the second place, by reason of the fact that austenite, the solid solution of carbon in iron, decomposes in the solid state into ferrite, or pure iron, and cementite (Fe3C), and that quenching from above this transition-range, no matter how rapid, cannot entirely prevent the change and thus preserve the austenite by itself at ordinary temperatures, it happens that under the microscope we find, in addition to the ferrite, Fe3C, and austenite, which the thermal diagram of steel requires, a series of transition-products with distinctive structures, to which have been given the names martensite, troostite, sorbite, etc. Now these transition-products, in addition to the solid solution, austenite, have been the source of much controversy, at times very bitter. One side would insist that, say, troostite was an entity, which the other side would deny, pointing out that it must be a transition-mixture, with a particular structure. That austenite was a solid solution of carbon in iron has been denied by one school; we have been told that Fe24C dissolved both Fe3C and Fe, and thus gave rise to a whole series of quenching-pro-ducts—all this in spite of the fact that no matter how the thermal diagrams differ in regard to cast-iron, they all agree in regard to the solid solution, austenite, for Fe24C finds no place on the diagram. Thus it happens that while the authorities fight both in regard to the iron carbon diagram and the structures met with in hard-

Jan 1, 1913

By W. C. Phalen

INTRODUCTION NOBODY will dispute the fact that the conservation in every legitimate manner of our valuable high-grade phosphate-rock deposits is a present-day problem of importance. The table and curve, given herewith, show. that during the past 10 years the exportation of high-grade rock has averaged very close to half the total output of the entire country. The bulk of this exportation is from Florida, for obvious reasons. It is plain that the deposits in this State, more particularly, are being wastefully depleted under a system of selecting the cream of the product for exportation to Europe, leaving the comparatively low-grade rock, running from 65 to 70 per cent., and under, in bone phosphate of lime, for our own n fertilizer manufacturers to work up when all the best rock is gone. In this paper the writer has endeavored to make a point of describing in some detail the important methods of production and conservation in Tennessee. These ought to prove of educational value to our American agriculturists and fertilizer manufacturers, and should result in a demand for the highest-grade rock, both for direct application to the soil and for use in making acid phosphate. It is certainly evident that the European

Jan 10, 1916

By John C. Draper

The principal object of an underground coal mine transportation system is to move coal from the face where it is produced to the outside of the mine where it is prepared for market. In addition to the movement of coal, a transportation system must also move supply materials to the inside ; it must move men in and out of the mine ; and it must move rock and other debris out of the mine for disposal. Usually, mine haulage is divided into three categories named for the various areas of the mine served : 1) Pace Haulage. This is used at face from the mining machine to the intermediate transport system. 2) Intermediate or Secondary Haulage. Generally this is used between face haulage and main haulage. Sometimes this is merely an extension of the main haulage. 3) Main Haulage. This extends from the secondary haulage to the outside and is usually either a track or conveyor system, sometimes a combination of both. Transportation modes of coal in the various areas pose different problems, but the whole system must be synchronized. For instance, at the face the coal should be removed quickly from the various places to facilitate the movement of machines, whereas the intermediate system just passes the same coal on to the main transportation system. Selection of the transportation system must be based on the seam height, mining methods used to extract the coal, capacity required, ease of coal handling, and haulage efficiency. When driving rooms, mine cars can be used. They often simplify supply haulage and rock handling because they can also handle these items. Conveyors could be used and would have a greater haulage capacity but they cannot handle supplies easily or segregate the rock. When using a different mining method, such as longwall, mine cars cannot be used because there is not sufficient space to move the cars at the face nor can the cars haul the coal without delays which would cause excessive losses in production. As for ease of handling

Jan 1, 1981

By Y. L. Yao

The solubility limit of oxygeu in a titanionn at 850°C has been determined by magnetic measurements as 12.5 + 0.5 pct (29.0—30,9 at. pct). Also in the susceptibility-co~centmtion curve, there is n distinct but not sharp maximum at 19.0 * 0.5 z~t pet (40.5--42.1 at. pct), which indicates the presence of the 6 phase. The magnetic susceptibilities of the alloys of the titanium-oxygen system were determined byEhrlich in 1939.' is alloys were prepared by sintiring mixtures of titanium and its oxide at high temperatures. On the titanium-rich side, despite the fact that the alloy compositions he measured crossed two phase boundaries, the limited results obtained

Jan 1, 1960

By W. L. Fink, R. S. Archer

This paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent, beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium docs not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. Commercial Possibilities of Beryllium Alloys Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to thc strength and corrosion resistance of thc aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

By E. C. Harder

AT a Meeting of the New York Section, on May 23, 1918, the sole subject of discussion was the nature and occurrence of iron ores in certain parts of the world.? Owing to the importance of this subject, it has been deemed' advisable to publish the remarks made at that meeting in the form of a paper, for presentation at the Milwaukee Meeting, instead of in the usual place, under News of Local Sections. The remarks related to the following districts: Brazil, by E. C. Harder, of the U. S. Geological Survey; Scandinavia, by Waldemar Lindgren, of the U. S. Geological Survey; Cuba, by C. M. Weld, of the U. S. Bureau 'of Mines; Southern Europe, by A. C. Spencer, of the U. S. Geological Survey; China, by H. Foster Bain, of the U. S. Bureau of Mines; Alsace-Lorraine, by Sidney Paige, of the U. S. Geological Survey. BRAZIL By E. C. Harder During the years immediately preceding the war, the iron ores of Brazil were attracting the attention of iron operators both in Europe and in the United States. This was clue to the large quantities of practically undeveloped ore available, and to its great purity. It is reasonably safe to state that had capital not been diverted from the exploitation of these deposits to war purposes, Brazilian iron ores would probably now be offered in European and American markets. It is certain that after the war these ores will play a prominent part in the economic reconstruction of Europe and perhaps in the development of America.

Jan 9, 1918

By B. Sadtler

The oldest producing district of Park county, and in fact one of the oldest producing gold-districts of the State, is situated on the head-waters of the Platte and tributary streams. Geo-

Jan 1, 1897

By D. B. Rushmore, K. A. Pauly

Of primary importance in mine-installations is the hoist, which has a very direct bearing on the successful operation of a mine. Conditions vary greatly with different mines, and especially in different localities. Such factors as depth, incline, the number of levels, permissible or desirable speeds, conditions of ore, etc., are always more or less special in each case. Veins of ore are never exactly duplicated, and the nature of the ground through which shafts are sunk may considerably modify permissible values. As mining-laws are made by the different States, they necessarily vary somewhat, and, even when not fully observed, they introduce factors which qualify the conditions of hoisting men and ore. The amount of timbering required is often of importance as relating to hoisting-conditions. Methods of loading ore affect the time required, as also does the question of the use of cars or skips. Safety-precautions must be very carefully considered, and the number of men in each mine, the number of compartments, and often the method of removing water from the mine, must have careful consideration. While a general discussion of the subject of hoisting is possible, most cases are entirely special, and can be considered only in connection with the peculiar conditions pertaining to that particular installation. The cost of installation of the hoisting-plant may be an appreciable amount, while the cost of raising the ore may be but a small part of the total operating-charge. In many cases, however, the output of the mine is limited by the capacity or the hoist, and the latter thus becomes of the first importance.

Jan 1, 1911

By K. C. Strebig, C. W. Schultz, A. A. Selim

The effect of some organic additives in diamond drilling of quartzite was investigated in the laboratory. The drill was designed to measure the rate of penetration, the thrust, and the torque and to record each as a function of the distance drilled. A statistical plan was followed throughout the investigation and an equation representing the bit performance was derived from the mathematical theory of reliability. The drilling torque was found to increase with the use of additives while the sliding coefficient of friction and the wear coefficient decreased. The energy per unit volume consumed was found to increase with the use of additives. A hypothesis explaining the effects achieved with the additives is given. INTRODUCTION For some time researchers have attempted to increase drilling efficiency by adding certain agents to the flushing medium. Much of this interest is the result of the observations of Rehbinder, Shreiner and Zhigach1 They postulated that "...in processes for the mechanical destruction of solids, a region of increased crack formation is created in the deformed layers adjoining that surface of destruction, forming the predestmction zone. The surrounding medium (for example, a liquid) which wets a given solid will penetrate the embryo microcracks of the predestruc-tion zone. Increasing the molecular affinity of this liquid for the surface of the solid considerably facilitates the deformation and destruction by softening the solid in the zone of increased crack formation. In this manner, the hardness or strength of the deformed body is decreased by the influence of the penetration of the liquid into the predestraction zone." This is known as the "Rehbinder effect". Rehbinder's work has prompted many investigators to examine the effect of additives on the mechanical destruction of rocks. Engelmann, Terichow and Selim reported that the maximum penetration of the rock by a diamond point in a solution environment was at the isoelectric point of the solution.* Robinson reported that his results did not appear to support the theory of Rehbinder.3 Joris and .McLaren suggested that additives with surface tension lower than water will be more efficient in cooling the diamonds.4 Their effectiveness in removing the fine cuttings from the face of the bit will also improve the efficiency of the system. They reported an improvement in impregnated bit life and penetration rates with the use of soluble oil additives. In contrast, Long and Agnew, drilling with surface set bits, reported that lubricating agents increase bit temperature and wear.5 A significant change was reported6 in the mechanical properties of rock with polar additives. It was concluded that this change in the mechanical properties of the rock in the presence of the additive is due to the rock hydrophilic properties. Ethylene glycol, glycerine and anionic detergent were selected for this investigation because their surface tension is lower than that of water. The surface tension of these additives for the concentrations studied was 42 to 75 percent of the surface tension of water. A low surface tension additive would wet the surface of the diamonds more easily and hence would be more effective in cooling the diamonds. Another characteristic of these low surface tension additives is their effectiveness in removing the cuttings and preventing the flocculation of the formed particles in the drilling process. This article summarizes the results of an investigation performed at the laboratories of USBM, Twin Cities Mining Research Center. The objective of the investigation was to study the over-all effects of some organic additives on the performance of diamond impregnated bits in atmospheric drilling conditions only and not in downhole pressured conditions.

Jan 1, 1970

By Harry L. Washburn, Robert L. Llewellyn, W. J. Halvorsen

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment. JUSTIFICATION FOR COAL PREPARATION During the past decade, major changes have occurred affecting the market, profit, and long-range planning of the coal industry. Mining companies have become "partners" with consumers at many new and some old mines, both for steam and metallurgical coals. Coal properties have become "assigned" tonnages at mutually agreed upon conditions and prices. Lower unit-train tariffs have been instrumental in helping coal markets to compete against oil and nuclear energy. Coal prices for power plants are still on a Btu (British thermal unit)

Jan 1, 1981

By A. F. Buddington

INTRODUCTION EVER since a genetic connection between many ore deposits and magmas began to be widely recognized, some two-score years ago, there has been much discussion of the complex and intricate problem of the genetic association of specific kinds of mineralization with specific kinds of igneous rocks. General discussions of the latter problem and pertinent data have been given by S. F. Emmons, Kemp, Lindgren, Niggli, Rastall, Spurr, Vogt, and others. In this paper no attempt is made to deal with mineral deposits genetically associated with volcanic rocks, but only with those presumed to be related to exposed intrusive masses. The writer is indebted to E. S. Bastin, F. F. Grout, Edward Sampson, and to the members of the committee in charge of the preparation of the volume, for a critical reading of the manuscript and many worth-while suggestions.

Jan 1, 1933

By H. F. Hebley

In recent years, especially in the last decade, great interest has been shown and many advances have been made in the preparation and cleaning of coal. In the major coal-producing countries, the percentage of tonnage cleaned has been increasing ever since 1924. As separating media, both liquids and gases are used, these generally being water and air respectively. Some systems, instead of obtaining separation by the velocity of the medium in which the coal is cleaned, depend on the density of water mixed with sand, or coal dust and shale, or with chemicals such as calcium chloride. In studying the results of coal-cleaning equipment, it will be observed that the efficiency of the cleaning apparatus lowers as the size of the coal decreases. This inability to obtain any marked improvement in the fines has been partly responsible for the installation of dedusting equipment, to remove the fine sizes from the raw coal prior to cleaning. When considering the possibility of installing dedusting equipment, many factors must be taken into account. Very often, but not always, both the ash and sulfur content of the coal increase as the coal size decreases. When bituminous coal, containing soft powdery fusain, is subjected to a wet washing process, the porous fines of the fusain remain in the small coal or in the wash water and delay the dewatering of the washed coal and increase the difficulty of clarification in settling tanks or thickeners. When a dedusted coal is cleaned by a wet process, the sludge recovered from the settling tank often runs so high in ash that the sludge can be discarded without further treatment and still the loss is small. Where treatment of the sludge is desired, however, froth flotation may be used to advantage if the size of the feed is below 1/10 in. Dust from the deduster can be treated in a similar manner. Fusain, which is usually found in the fine sizes, has often a much larger ash content than other coal. Illustrative of this condition is a table of ash contents for the various petrographic constituents of Illinois coal (No. 5 bed) as given by Mitchell' (Table 1).

Jan 1, 1934

By Michael H. Kuryla, Galen H. Clevenger

Some years after Nobel made his epoch-making contribution to the knowledge of high explosives, Sprengell described a new class of detonating explosives consisting of mixtures, made immediately before use, of an oxidizing agent and a combustible substance.2 The novel feature of the Sprengel explosives is that the constituents alone are non-explosive during manufacture, storage and transport. Despite this advantage, and although some of these have been used in important work, they are now little used, possibly on account of the greater inconvenience to the user, compared with explosives supplied by the manufacturer in final form. Liquid-oxygen explosives are a type of Sprengel explosive in that the oxidizing agent (liquid oxygen) and the combustible substance or substances (solid carbonaceous matter alone or in combination with liquid hydrocarbons or even metallic powders and, at times inert absorbents) are brought together immediately before use. The components separately are non-explosive. The possibility of using liquid oxygen as one of the components of an explosive was perhaps first suggested by Sprengel, who stated that the beau ideal of a detonating explosive was a mixture of eight parts of liquid oxygen with one part of liquid hydrogen. Although the liquefaction of air3 had been accomplished in the laboratory as early

Jan 1, 1923

By Michael H. Kuryla, Galen H. Clevenger

Some years after Nobel made his epoch-making contribution to the knowledge of high explosives, Sprengell described a new class of detonating explosives consisting of mixtures, made immediately before use, of an oxidizing agent and a combustible substance.2 The novel feature of the Sprengel explosives is that the constituents alone are non-explosive during manufacture, storage and transport. Despite this advantage, and although some of these have been used in important work, they are now little used, possibly on account of the greater inconvenience to the user, compared with explosives supplied by the manufacturer in final form. Liquid-oxygen explosives are a type of Sprengel explosive in that the oxidizing agent (liquid oxygen) and the combustible substance or substances (solid carbonaceous matter alone or in combination with liquid hydrocarbons or even metallic powders and, at times inert absorbents) are brought together immediately before use. The components separately are non-explosive. The possibility of using liquid oxygen as one of the components of an explosive was perhaps first suggested by Sprengel, who stated that the beau ideal of a detonating explosive was a mixture of eight parts of liquid oxygen with one part of liquid hydrogen. Although the liquefaction of air3 had been accomplished in the laboratory as early

Jan 1, 1923

By E. W. Shaw

Continued discussion of the paper of Roswell H. JOHNSON, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 221 to 226. See also Bulletin No. 101, May, 1915, pp. 1157 to 1162. E. W. SHAW, Washington, D. C. (communication to the Secretary+). -With the word petrology-literally the science of rocks-being used primarily for igneous rocks, and with geophysics coming to mean the study of lavas and the rocks into which they solidify, contributions to the knowledge of the physical chemistry of sedimentary rocks, even though only ideas which may be used as working hypotheses, become most welcome. The forces which control the formation and subsequent history of the stratified portions of the earth's crust are so little known that no one has yet been able to settle finally the questions as to whether petroleum is of organic or inorganic origin; whether it originated far from its present position, or nearby. Yet both the chemical and physical problems of the rocks in which oil occurs seem to be more simple than those of the igneous rocks. The oil-bearing rocks of western Pennsylvania, for example, have in all probability never been subjected to a pressure exceeding 3,000 or 4,000 lb. to the square inch, nor to a temperature higher than 100° or 200° C. These pressures are considerably below the crushing strength of rocks, and the temperature far below their melting point. The igneous rocks,, on the other hand, have been affected by enormous pressures and very high temperatures and yet steady progress is being made in reproducing in the laboratory the conditions of their formation and subsequent modification within the earth. The solution of the sedimentary-rock problems would seem to be fully as important as those of igneous rocks, and yet we must content ourselves with reasoning backward and our inferences as to what has happened are oftentimes little more than guesses.1 One of the fundamental problems is the origin of the salt water in oil fields. Is the salt water fossil sea water; has it been formed by the solution o-f salts of various kinds from distinct beds, from disseminated par-ticles, and from the weathering of suitable grains in the rock; or is it of deep-seated origin? Its general resemblance to sea water points to the first, but the principles held by some concerning the free circulation of water throughout the earth's crust, and certain peculiarities of composition indicated by the few analyses available, seem out of harmony with such an explanation.

Jan 7, 1915

By H. D. Newell

THERE has been much research and commercial development in recent years in the use of chromium and nickel in steels of various types, including those intended for high-temperature service. By "high-tem-perature steels" are meant those specifically designed for service at ele-vated temperatures in steam plants, oil refineries and other industries where high-temperature operations are conducted. This paper is devoted to some preliminary data on the effect of silicon on certain of the most popular chromium-molybdenum steels now being used in quantity by the refining industry and includes a short statement on the influence of copper in steels intended for high-temperature service.

Jan 1, 1937

By Norman Goss

IT is generally agreed that cold-working mechanically refines the grains into smaller fragments and with continued working these are oriented with certain crystallographic directions bearing a relation to the direction in which the metal is worked. Some of the energy expended on the metal during plastic deformation appears in the form of heat, but a very small portion remains in the metal as stored energy. The entropy, specific heat capacity, temperature at which recrystallization will just begin, density, ductility, elasticity, tensile strength, and resistance to corrosion are affected. These properties have been studied extensively and some of the changes in the physical properties due to cold-working were attributed to lattice distortion.1-8 The broadening of the K. lines on the X-ray diffraction diagrams of plastically deformed metals is believed to indicate lattice distortion, and consequently the existence of internal stresses. The evidence supporting this theory rests solely upon the observed experimental fact that the dif-fraction lines are broadened and the K a doublets are completely diffused. Elam9 has reviewed the matter of lattice distortion in relationship to the hardening of metals by plastic deformation. The X-ray diagrams of plastically deformed metals differ in general from annealed metals. The hardening of a metal was believed due to lattice distortion.9 The resolu-tion of the doublet is lost when a metal is cold-worked and the Lane spots are elongated. At one time this elongation was thought to indicate the elastic bending of the crystal planes. However, more careful work showed that the asterism was due to new orientations developed within the fragmented grains during plastic deformation. Some theories attrib-uted the hardening to fragmentation of the grains into smaller units.

Jan 1, 1940

By Robert Keeney

Before the outbreak of the war in 1914, the only electric-furnace smelting plant operating on a commercial basis west of the Mississippi River was an electric pig-iron plant in California; rare metal ores were not smelted, concentrates of molybdenum, tungsten, uranium, and vanadium ores being shipped east for reduction. Practically no- chrome ore was being mined, and only comparatively small amounts of manganese ore. Today there are two electric smelting plants in California, one in Washington, one in Iowa, and four in Colorado; two plants are under construction in California, and one in Montana. Ores of manganese, chromium, molybdenum and tungsten are now smelted in the West, and although uranium and vanadium concentrates are still shipped to the East, they will probably be treated in western plants in a short time. The four electric-furnace plants in Colorado are listed in Table 1. TABLE 1.-Electric Smelting Plants in Colorado Capacity, Company, Location Kilowatts Products . Tungsten Products Co Boulder 800 Ferrotungsten, ferromolybdentun. Boulder Tungsten Production Co. . Boulder 400 Ferrotungsten. Ferro Alloy Co Utah Junction 1200 Ferrochrome, ferrotung-sten. Iron Mountain Alloy Co Utah Junction 3000 Ferromanganese. Power for all of these plants is supplied by the Colorado Power Co.

Jan 8, 1918