Search Documents

By R. W. Powers, M. V. Doyle

ThE solution of a diatomic gas such as 0, or N2 in a metal usually follows Sieverts' law; i. e., Here C is the solute concentration at equilibrium and P, the gas pressure. The proportionality constant Ks is also the equilibrium constant for the reaction 1/2 02 (at pressure, P) - 0 (in solution at [21 concentration., C). to use oxygen as an illustrative gas. Sieverts' law is therefore interpreted to indicate that diatomic gases go into metallic solution atomically and that the solute "gas" atoms interact negligibly with each other. Of course, this interpretation is strictly valid only over the temperature interval in which the reaction indicated in [Z] can be investigated. At temperatures several hundreds of degrees below this interval, the possibility of interactions between solute atoms is conceivable. Indeed, from internal-friction measurements some evidence for the existence of groupings of oxygen atoms in tantalum solid solutions was presented a few years ago.1,2 Over a range of solute concentration, the experimental oxygen internal-friction peak in tantalum, measured as a function of temperature at constant frequency of vibration, can be described as the sum of two elemental peaks, each corresponding to a separate relaxation process. At 0.7 cps, the height of the elemental peak found at 137°C is proportional to the oxygen content, whereas the height of the one at 162°C varies as the square of the oxygen concentration. The 137°C peak was presumed to arise from the stress-induced ordering of oxygen atoms among various classes of octahedral sites in the manner proposed by Snoek.3 The 162°C peak was attributed to a somewhat similar stress-induced ordering process, in which each oxygen atom was interacting with a neighboring oxygen atom. Similarly, the experimental peak due to nitrogen in tantalum can also be described as the sum of two peaks. The height of one varies as the nitrogen concentration and the other as the square of this quantity. In fact, some evidence of solute interactions exist for all oxygen and nitrogen solid solutions of Group V transition metals. However, the interaction energy was not obtained previously for any alloy. The determination of this quantity, as a part of a more intensive study of the interaction between oxygen atoms in solid solution in tantalum, is reported in this paper. PRINCIPLE OF THE EXPERIMENT Consider an equilibrium in a solid solution of tantalum between oxygen atoms which are bound together pairwise and those solute oxygen atoms which are not so associated. 20 (Ta) - O2 (Ta) [3]

Jan 1, 1960

By B. S. Hickman

Using primarily quantitative single crystal X-ray techniques studies have been made of the precipitation of the metastable w phase in alloys of titanium with Mo, Mn, Fe, Cr, and Nb. It is shown that, in agreement with earlier work on the Ti-V system, the composition of the w phase during aging approaches a constant; the value varies from one system to another in a systematic manner with the electron concentmtion. Results relevant to the mechanism of w precipitation during quenching and during aging are presented and discussed. Results are presented to confirm that the w phase is coherent and the nzorphology of the Necipitates is described and discussed. PRECIPITATION of the metastable w phase in alloys of titanium is of interest because of its severe embrittling effect and also because of the enhancement of the superconducting properties which accompanies precipitation.1 The general features of w phase precipitation have been discussed by cuillan and by Bagaratskii et d3 The work described in this paper forms part of a general study of w phase precipitation which was undertaken to elucidate various unknown or controversial features of the process, namely: i) What is the mechanism of formation of the phase ii) How does its composition, morphology, volume fraction, and particle size vary with the type and content of the alloying element and with the heat treatment conditions? iii) What is the relation between the w phase and the equilibrium a phase? In a previous paper4 the results of a detailed study of w phase in Ti-V alloys were presented. It was shown that: U During aging the composition of the w phase approached a saturation value of 13.5 to 14.0 at. pct V. ii) w precipitated as cube shaped particles and once precipitation was complete, particle coarsening did not occur. iii) a phase formed initially by direct conversion of w-phase precipitates. In this paper similar measurements are reported on Ti-Mo alloys and some more limited data given on the Ti-Cr, Ti-Fe, Ti-Mn, and Ti-Nb systems. The results i.1 the six systems are then compared. It has been shown previously by electron microscopy that the w precipitates as ellipsoids in both the Ti-Nb system,&apos; and in i-o.&apos; Blackburn and williamsz3 have reported the precipitates in Ti-Fe, Ti-Cr, and Ti-Mn are cubic, i.e., similar to the Ti-V system.476 EXPERIMENTAL METHODS 1) Specimen Preparation. Samples of the compositions shown in Table I were prepared by arc melting. High purity electron beam zone refined titanium (Materials Research Corporation Grade I—total impurity content =250 ppm) was used; the other source materials are given in the table. A commercial Ti-8 wt pct Mn alloy was used for studies of this system. After homogenization the materials were rolled or cut into strip approximately 1/4 in. by 2 in.; the strip was then heated at temperatures of 1200" to 1300°C for several hours by passage of a direct current through the strip in an ultra high vacuum system (<10-torr) and then quenched by admitting high purity helium and switching off the current. This treatment resulted in crystals up to 2 in. by 2 in. by A in., almost all of which had a [100] direction nearly perpendicular to the plane of the strip. The crystals were cut from the strip by spark machining and their composition checked by lattice parameter measurements supported by chemical analysis. 2) X-Ray Diffraction Methods. Lattice parameter measurements were made using a modification of the single crystal spectrometer described by ond. In this technique the crystal angles for reflection on either side of a highly collimated primary beam are measured. Generally the 400 CuK, or the 400 CuKp reflections of the bcc lattice were used. In the as-quenched crystals a precision of 1 in 105 was obtained, but due to line broadening the parameters in aged materials could only be measured to 1 in lo4. This accuracy was, however, quite adequate for the purposes of these experiments and enabled the composition of the p phase to be obtained to 10.1 pct in all systems except Ti-Nb where the lattice parameter change with composition is very small. The precipitation and growth of the w phase was examined using a single crystal goniometer attached to a Phillips diffractometer. The relative intensities and line shapes of b-phase and w-phase reflections

Jan 1, 1970

By Wallace E. Pratt

UNDER the stimulus of war psychology the American public has grown confused and jittery in its thinking on the subject of this nation&apos;s petroleum resources. This confusion arises from the failure of the average citizen, and even of many leaders in government, in our armed forces, and in the petroleum industry itself, to distinguish between our proved reserves of petroleum in the several oil-producing states and the total petroleum re- sources available to this nation. Leaders and public alike examine the accepted estimates of our proved reserves and thoughtlessly conclude that these estimates represent the total of our petroleum resources. Our fears are aggravated if we turn to the statistics on oil-finding and observe that the discovery of new reserves has waned decidedly in recent years. This confusion is dangerous because, under its influence, ill - considered policies spring up and flourish, choking out the most valuable fruits of the long experience of the American petroleum industry.

Jan 1, 1944

By H. I. Aaronson

ONLY limited studies have been made of pro-eutectoid a morphology in hypoeutectoid Ti-Cr alloys during previous investigations, 1-3 The nature of the eutectoid reaction, ß?a + TiCr2, has been considered in somewhat more detail.1,2,4,4 Inasmuch as the proeutectoid ferrite reaction in plain carbon steels has recently been extensively investigated in this laboratory, advantage has been taken of the opportunity to compare the morphologies developed in two rather different eutectoid systems in order to permit a preliminary estimate to be made of the degree of generality which may be ascribed to the various results obtained. Experimental Procedure The chemical analyses of the alloys used are given in Table I. The 7.22 pct Cr alloy was prepared by the Battelle Memorial Institute from iodide titanium and high purity chromium. The initial ingot was made by arc melting a master alloy and iodide titanium. The resultant ingot was twice remelted. by the consumable electrode technique. Upset forging at 950°C reduced the final ingot to 3/4 in. sq bars. The 10.94 pct Cr alloy was prepared by the Titanium Metals Corp. of America from sponge titanium and chromium of ordinary purity. This alloy was melted twice by the consumable electrode technique, forged at 1200° to a 3/4 in. sq bar, and rolled at 815°C to a 1/2 in. round. Specimens 1/4 in. x 1/4 in. x 1/16 in. were cut from the 7.22 pct Cr alloy; halves of disks 1/2 in. in dlam and 1/16 in. thick served as specimens of the 10.94 pct Cr alloy. These specimens were individually encapsulated in Vycor, Each capsule was evacuated three times to a pressure of 2 to 6 x lo-&apos; mm Hg and flushed twice with a reduced pressure of argon prior to sealing. The inclusion of two small packets of zirconium chips permitted the capsules to be outgassed and internally gettered, without heating the specimen, prior to heat treatment. The specimens were solution annealed for 40 min at 1000°C, isothermally reacted in deoxidized lead pots, and quenched in iced water. Most of the isothermal reaction treatments were carried out at 25" intervals between 725° and 550°C on specimens of the 7.22 pct Cr alloy and at 650°C on specimens of the 10.94 pct Cr alloy. Results and Discussion Morphologies of Proeutectoid a*—Kinetics of the ß?a Reaction: Fig. 1 shows the TTT-curves for the beginning of the proeutectoid a and the eutectoid reactions in the temperature range investigated in the 7.22 pct Cr alloy. The M, temperature in this alloy is below 0°C. The curve for the beginning of the proeutectoid a reaction is in good agreement with that of Frost, Parris, Hirsch, Doig, and Schwartz&apos; for a 7.54 pct Cr alloy, appears at considerably earlier reaction times than the corresponding curve presented by Rostoker4 for a 7 pct Cr alloy, and lies athwart the curve of Spachner and co-workers11 for an 8 pct Cr alloy. Differences in criteria for the beginning of the a reaction and the relatively high rate of this reaction at lower temperatures presumably account for some of these divergences and may also explain, in part, the apparent failure of an iodide-base 7.22 pct Cr alloy to react more slowly than sponge-base 7 to 8 pct Cr alloys. Grain Boundary Allotriomorphs: Crystals of this morphology nucleate at and grow preferentially and more or less smoothly along the matrix grain boundaries.5-7 Allotriomorphs are the first morphology to precipitate at most grain boundaries at reaction temperatures from 725°C, the highest temperature studied, at least through 575°C. Fig. 2 Shows typical allotriomorphs, formed during an early stage of transformation at 725°C. Grain boundary allotriomorphs are not the predc=iaant morphology at late reaction times at any temperature studied. However; from 725" through

Jan 1, 1958

By G. D. Cody, D. S. Beers, B. Abeles

The thermal diffusivity (thermal conductivity divided by specific heat) of Armco iron has been measured over the temperature range 30º to 1025ºC. The results are in good agreement with the thermal diffusivity computed from published values of thermal conductivity and specific heat, except near the Curie point and at the a to y phase transition, where the measured diffusivity undergoes rabid variations. The differences observed are ascribed to a rapid variation in the electronic thermal conductivity near the Curie point, and a decrease in the lattice thermal conductivity, at the a to ? phase transition. A major difficulty in measuring the thermal conductivity of materials at high temperatures is the determination and elimination of radiation losses. It has been shown, however, that in measuring thermal diffusivity D (thermal conductivity/specific heat) radiation losses can be taken into account exactly.&apos; In order to test the performance of a newly designed apparatus for measuring thermal diffusivity of solids,&apos; we measured Armco iron to an accuracy of 2 pct in the temperature range 30" to 1025°C. This material was selected since both the thermal conductivity,3&apos;4 k, and specific heat,5 C, are known accurately in this temperature range and thus the measured values of D could be compared with D computed from the pub-

Jan 1, 1962

By H. I-Lieh Huang, O. D. Sherby, J. E. Dorn

RECENT investigations1-4 have suggested that the total plastic strain, C, for high temperature creep under a given stress can be correlated by means of a temperature-compensated time, te- where t is the duration of test, e is the base of natural logarithms, aH is the activation energy for creep, R is the gas constant, and T is the absolute temperature. A typical set of data on which this deduction was based is given in Fig. la. Inasmuch as the e-in t curves for the various temperatures are identical except for their displacement along the In t axis where f and are appropriate functions. If the increase in creep rate with an increase in temperature is exclusively ascribable to a single process involv- ing thermal activation, (T) should equal RT and therefore it = constant [2] where ?= te Assuming the validity of this relationship, ? = ?2 at the same strain, or where the subscripts refer to two alternate test conditions.

Jan 1, 1957

By A. C. Wallace

THE development of the natural resources of any district of any magnitude, inevitably gives rise to many problems off title, usually due to the greatly enhanced value of the land. The development of the mining industry in the Quapaw Agency has been no exception to this general rule. Our problems, how-ever, have not been many or particularly serious. The Quapaws were allotted and patents issued by the United States Government in 1895. These patents contained a restriction against alienation for a pe-riod of twenty-five years. The effect of the restric-tion was to prevent the Indian from selling, leasing, or in any way encumbering his land. The Govern-ment, in a paternalistic spirit, sought to teach the Indian thrift and industry and to insure him a place of residence. This is evidenced by the first Leasing Act passed by Congress, which permitted only incom-petents and those physically disabled to lease their land for either agricultural or mining purposes. The able-bodied Indian was denied the right to lease. It soon became apparent to the Government, how-ever, that this was a mistaken policy, and in 1897 a General Leasing Act was passed by Congress and it was under this act that the mining industry in the Quapaw Agency was developed. The act, reads as follows: "That the allottees of land within the limits of the Qua- paw Agency, Indian Territory, are hereby authorized to lease their lands, or any part thereof, for a term not ex-ceeding three years, for farming or grazing purposes, or ten years for mining or business purposes. And said al-lottees and their lessees and tenants shall have the right to employ such assistants, laborers, and help from time to time as they may deem necessary: Provided, That when-ever it shall be made to appear to the Secretary of the Interior that, by reason of age or disability, any such allottee cannot improve or manage his allotment properly and with benefit to himself, the same may be leased, in the discretion of the Secretary, upon such terms and conditions as shall be prescribed by him. All acts and parts of acts inconsistent with this are hereby repealed." It was the interpretation of this Act that gave rise to our first serious problems. It will be noted that the Act says that "allottees of land" within the limits of the Quapaw Agency are authorized to lease their land. Thus, the first question was presented by the use of the term "allottee," and the question was as to whether or not Congress intended to limit the Quapaw Indian to the leasing of his own allotment or did Congress mean that the term "allottee" was synonym-ous with "Indian" and intend to give the Indian a right to lease both his allotment and his inherited land and was an Indian without an allotment an "allottee" even though he was a member of the Qua-paw tribe and the owner of the Quapaw land by in-heritance, and not being an allottee, could he lease his inherited Quapaw land under the authority granted in this Act?

Jan 5, 1928

By P. Somasundaran, G. E. Agar

The role of calcium, phosphate, and fluoride species in determining the zeta potential of apatite in aqueous solutions was investigated in this study. The zeta potential of apatite was determined by streaming potential measurements over a wide range of concentrations of potassium nitrate, calcium nitrate, potassium dihydrogen phosphate, and potassium fluoride solutions at various pH values. While the addition of phosphate made the apatite surface more negative at all pH values, calcium caused a significant increase of the zeta potential only when the zeta potential was negative. Fluoride addition had only a minor effect on the zeta potential, but both negative and positive values were increased.

Jan 1, 1973

By W. M. McKewan

Magnetite pellets were reduced in flowing hydrogen at pressures up to 40 atm over a temperature range of 350° to 500°C. The rate of weight loss of oxygen per unit area of the reaction surface was found to be constant with time at each temperature and pressure. The reaction rate was found to be directly proportional to hydrogen pressure up to 1 atm and to approach a maximum rate at high pressures. The results can be explained by considering the reaction surface to be sparsely occupied by adsorbed hydrogen at low pressures and saturated at high pressures. PREVIOUS investigation1,2 have shown that the reduction of iron oxides in hydrogen is controlled at the reaction interface. Under fixed conditions of temperature, hydrogen pressure, and gas composition, the reduction rate is constant with time, per unit surface area of residual oxide, and is directly proportional to the hydrogen pressure up to one atmosphere. The reduction rate of a sphere of iron oxide can be described3 by the following equation which takes into account the changing reaction surface area: where ro and do are the initial radius and density of the sphere; t is time; R is the fractional reduction; and R, is the reduction rate constant with units mass per area per time. The quantityis actually the fractional thickness of the reduced layer in terms of fractional reduction R. It was found in a previous investigation2 of the reduction of magnetite pellets in H2-H,O-N, mixtures, that the reaction rate was directly proportional to the hydrogen partial pressure up to 1 atm at a constant ratio of water vapor to hydrogen. Water vapor poisoned the oxide surface by an oxidizing reaction and markedly slowed the reduction. The enthalpy of activation was found to be + 13,600 cal per mole. It was also found that the magnetite reduced to meta-stable wüstite before proceeding to iron metal. The following equation was derived from absolute reaction-rate theory4,8 to expfain the experimental data: where Ro is the reduction rate in mg cm-2 min-&apos;; KO contains the conversion units; Ph2 and PH2O are the hydrogen and water vapor partial pressures in atmospheres; Ke is the equilibrium constant for the Fe,O,/FeO equilibrium; Kp is the equilibrium constant for the poisoning reaction of water vapor; L is the total number of active sites; k and h are Boltzmann&apos;s and Planck&apos;s constants; and AF is the free energy of activation. Tenenbaum zind Joseph5 studied the reduction of iron ore by hydrogen at pressures over 1 atm. They showed that increasing the hydrogen pressure materially increased the rate of reduction. This is in accordance with the work of Diepschlag,6 who found that the rate of reduction of iron ores by either carbon monoxide or hydrogen was much greater at higher pressures. He used pressures as high as 7 atm. In order to further understand the mechanism of the reduction of iron oxide by hydrogen it was decided to study the effect of increasing the hydrogen pressure on rebduction rates of magnetite pellets. EXPERIMENTAL PROCEDURE The dense magnetite pellets used in these experiments were made in the following manner. Reagent-grade ferric oxide was moistened with water and hand-rolled into spherical pellets. The pellets were heated slowly to 550°C in an atmosphere of 10 pct H2-90 pct CO, and held for 1 hr. They were then heated slowly to 1370°C in an atmosphere of 2 pct H2-98 pct CO, then cooled slowly in the same atmosphere. The sintered pellets were crystalline magnetite with an apparent density of about 4.9 gm per cm3. They were about 0.9 cm in diam. The porosity of the pellets, which was discontinuous in nature, was akrout 6 pct. The pellets were suspended from a quartz spring balance in a vertical tube furnace. The equipment is shown in Fig. 1. Essentially the furnace consists of a 12-in. OD stainless steel outer shell and a 3-in. ID inconel inner shell. The kanthal wound 22 in. long, 1 1/2, in. ID alumina reaction tube is inside the inconel inner shell. Prepurified hydrogen sweeps the reaction tube to remove the water vapor formed during the reaction. The hydrogen is static in the rest of the furnace. The sample is placed at the bottom of the furnace in a nickel wire mesh basket suspended by nickel wire from the quartz spring. The furnace is then sealed, evacuated, and refilled with argon several times to remove all traces of oxygen. It is then evacuated, filled with

Jan 1, 1962

By G. Sachs, S. I. Liu

INTRODUCTION IN a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in, Fig I,§ the ductility (EF) retained after prestraining in tension by a certain amount (EI) and measured in a subsequent tension test is represented by a straight line sloping down under 45°. If a compression of the same magnitude as the first tension is inserted (E2 - EI) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. . The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.2 As also shown in Fig I, the ductility in subsequent tensile tests decreased with compression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount E1, subsequently straining in compression by an amount E2, and finally determining the retained ductility, Ef, in a tensile test. Prestraining in tension is then represented by E1 > o and E2 = o. Prestraining in compression is given by E1 = o and e2 < o. Balanced cyclic straining is defined. by the condition E1 > o and E2 = -El. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, E1, and the compression strain, E2, within extreme limits; El varied between 0.06 and 0.28 and E2 between -0.008 and -0.60 approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date. The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the subsequent tensile tests.

Jan 1, 1948

By C. F. Wang

Page I. Introduction............:.............. 395 Manchuria in General ....................... 395 Pen-hsi-hu............................ 397 Pen-hsi-hu Coal & Iron Co., Ltd................... 399 I1. organization........................... 400 III. Coal Deposit........................... 402 Location..............................402 Geology............................. 403 Coal Mining...........&apos;.................. 404 Mining Methods........................407 Mining Cost.........................408 IV. Coal Washing Plant.......................408 V. Coking Plant..........................410 VI. Iron Deposit...........................413 Magnetite Belt.......................... 413 Origin of Deposit......................... 414 Iron Mining........................... 415 VII. Concentration Plant........................ 417 VIII. Briquetting Plant.......................... 418 IX. Blast-furnace Smelting...................... 418 iNTKODtrCTION Manchuria in General Manchuria. called the "Three Eastern Provinces" in Chinese. forms the northeastern corner of China and is bordered by Siberia on the north and northeast. and by Korea on the east. It is a land famous in Chinese annals as the place of origin of the Ching dynasty. and in more recent times it has bcen an arena for diplomatic maneuvering and commercial competition between the Russians. advancing from the north. and the Japanese from the southeast. It derives its name of "three eastern provinces" from the fact that it is divided into three provinces; Hei-

Jan 1, 1918

By A. F. Melcher

The present paper is a progress report on an investigation of the physical factors of oil and gas and especially of their sands,&apos; such as pore space, size of pores or permeability, retentivity, viscosity of the oil, temperature, pressure, thickness and area of the pay sand, water relations, and capillarity. The purpose is to determine as many of these physical factors as possible, and to ascertain the relations existing, directly or indirectly, between these physical factors and the production of oil and gas. As yet only pore space2 and size of grains of pay sands have been investigated, although an apparatus has been designed to determine the permeability of a sand to oil, water, or gas under definite drops of pressure between the entrance face and exit face of the sample. Messrs. E. W. Shaw, R. Van A. Mills, D. Dale Condit, G. B. Richardson, G. C. Matson, and C. H. Wegemann collected the samples upon which the physical determinations were made. Acknowledgment is made to my colleagues of the United States Geological Survey for many suggestions and criticisms; to Mr. Mills for the production data given of the oil wells from which some of the samples were collected; to Mr. A. W. McCoy of the Empire Gas and Fuel Co., Bartlesville, Okla., for many ideas. Determining Pore Space of Oil and Gas Sands In selecting a method for the determination of pore space, two objects were kept in mind: First, the method must not only be sufficiently

Jan 1, 1921

[Appalachian Petroleum Section: Chairman: Robert H. Edele, 1st V.C.: Robert Vutech, 2nd V.C.: Robert Tullis, Sec.-Treas.: Frederick T. Solomon. Meets last Tuesday of each month in Charleston, W. Va. Balcones Section: Chairman: Dr. Frank W. Jessen, 1st V.C.: Gilbert M. Andreen, 2nd V.C.: Lloyd N. Johnson, Seo.-Treas.: W. C. Vercellino. Big Horn Basin Subsection: Chairman: B. E. Yester, 1st V.C.: Robert J. Woodhall, 2nd V.C.: Herbert A. Koch, Secretary: Dean Costello, Treasurer: Thomas W. DeLong. Meets 2nd Wednesday; alternating between Cody and Worland. Billings Petroleum Section: Chairman: George O. Ellis, 1st V. C.: Robert L. Spottswood, 2nd V. C.: Robert M. Watkins, Sec-Treas.: Joseph H. Bato. Meets 5:30 p.m., 3rd Tuesday at Billings Press Club.]

Jan 1, 1961

By Frank A. Linforth

The object of this paper is to present a brief outline of the methods of geologic mapping employed in the Geological Department of the Anaconda Copper Mining Co., at Butte, and to show by means of a few typical examples the practical nature of the results obtained. The extremely complicated geological conditions early encountered in Butte mining led mine operators to realize the necessity of accurate detailed geologic mapping m an aid to successful development of the ore bodies. The organization of the Anaconda Geological Department was undertaken in 1900 by H. V. Winchell, who, in conjunction with D. W. Brunton, worked out the essential methods of procedure which are, in the main, followed at the present time. Since the year 1906 the geologic work has been under the direction of Reno H. Sales, and in some respects the scope of the work has been slightly enlarged. An excellent article describing the general equipment of the geological department was presented by D. W. Brunton at the British Columbia meeting of the Institute in 1905.&apos; His idea, that data collected underground and recorded should be put to practical use and not remain a mere " inventory of the company&apos;s underground possessions," is the keynote to the success of applied geology in Butte. The geologic notes are taken as soon as possible after the ground is broken so that any mistake in the mining may be corrected at once, or any particularly advantageous procedure may be suggested before any useless work is done. Taking the notes underground is a comparatively simple matter, but a few necessary precautions may be pointed out. The essential to success is that the notes shall show exactly what geological facts are disclosed. The observer must discriminate carefully between important and unimportant exposures in making the record, especially as regards the relation between veins and stringers, between faults and minor slips, or between the characteristics of veins of different ages. A simple color scheme has been adopted for making this record. Red pencils are used to indicate

Jan 1, 1914

By B. M. Larsen, L. S. Darken

SOME years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general. our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2-by a high concentration of active (or "free") lime and of manganese oxide dis) solved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. DISTRIBUTION OF MANGANESE BETWEEN SLAG AND METAL AT EQUILIBRIUM On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction [FeO + Mn ;7± MnO + Fe [A] slag metal slag metal] the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as [K" aFPI OFeO ? aMn] where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term aFe may he combined with K" to give a new constant K&apos;. Making these changes.

Jan 1, 1942

By B. M. Larsen, L. S. Darken

Some years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2) by a high concentration of active (or "free") lime and of manganese oxide dissolved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. Distribution 02 Manganese between Slag and Metal at Equilibrium On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction FeO + Mn -& MnO + Fe [A] slag metal slag metal the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as K,, _ aMnO&apos; afe aFeO &apos; aMn where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term afe may be combined with K" to give a new constant K&apos;. Making these changes, 7

Jan 1, 1942

By B. M. Larsen, L. S. Darken

Some years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2) by a high concentration of active (or "free") lime and of manganese oxide dissolved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. Distribution 02 Manganese between Slag and Metal at Equilibrium On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction FeO + Mn -& MnO + Fe [A] slag metal slag metal the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as K,, _ aMnO&apos; afe aFeO &apos; aMn where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term afe may be combined with K" to give a new constant K&apos;. Making these changes, 7

Jan 1, 1942

APPROXIMATELY 90 per cent of the steel that is melted and refined in the United States and poured into ingots is made in basic open-hearth furnaces, as shown in Table 1-1. The annual ingot capacity of the steel industry reported January 1, 1950, by the American Iron and Steel Institute3* was 99,040,160 tons, of which the basic open-hearth process accounted for 85,896,580 tons, 86.7 per cent of the .total. The capacity of the individual furnaces varies over a wide range, a large majority falling within limits of 50 to 200 tons (Fig 1-1). Most of the units constructed [ ] since 1942 are in the larger size groups, between 175 and 225 tons capacity.

Jan 1, 1964

By Blake M. Loring

Recently the S-curves for 30 to 40 alloy steels have been pub1ished.l.2 These steels show individual characteristics, which make each additional S-curve of great interest. There are important differences in the mechanism of the transformation process, the type of transformation product, and the influence of alloying elements. Steels of the same general alloy composition may possess such variable characteristics with regard to the length of time of isothermal transformation that an S-curve for each heat of steel may be desirable. In the present work the isothermal transformation of a steel having the following composition and grain size was studied: 0.29 per cent carbon; 0.21 manganese; 0.026 phosphorus; 0.017 sulphur; 0.056 silicon; 1.45 chromium; 3.25 nickel; austenite grain size, 7. The progress of the isothermal transformation was followed by several different methods, including hardness measurements, dilatometer observations, and examinations of the microstructure. It was not expected that these methods would be in precise agreement.3 Accordingly, the changes in microstructure and hardness were given additional weight in determining the initial stage of transformation and the dilatometer measurements were relied on in estimating the completion of the process. The beginning of transformation was indicated by I per cent of transformation products and the end of transformation by about 99 per cent. The reproducibility of the various methods in the ranges of highest sensitivity was checked by several observations at each time and temperature. The steel used in this investigation was annealed for 24 hr, at 925°C. Macroetching revealed no serious segregation. The specimens for the metallographic and hardness investigations were 1¼ by ½ by ? in. Wires attached to the samples were used for handling. instead of tongs, to avoid chilling. The specimens were heated at 845°C. for ½ hr. and quenched into constant-temperature salt baths held at various temperatures from 205&apos; to 650°C. The time required to transfer the specimens was found to be about 1½ sec., and nearly 5 sec. more was required for them to come to the temperature of the bath. After various lengths of time in the constant-temperature baths the specimens were quenched in water at 2I°C. The specimens were cut in half for the metallographic examination, to provide a surface free from decarburization. To determine the beginning and end of the transformation the percentage of transformation determined metallographically and by hardness was plotted against time. A planimeter was used in the metallographic determination. The hardness and metallographic determinations made at room temperature were confirmed reasonably well by dilatometer measurements taken during the process of transformation at the various temperatures. Two dilatometers were used to

Jan 1, 1942

By Blake M. Loring

Recently the S-curves for 30 to 40 alloy steels have been pub1ished.l.2 These steels show individual characteristics, which make each additional S-curve of great interest. There are important differences in the mechanism of the transformation process, the type of transformation product, and the influence of alloying elements. Steels of the same general alloy composition may possess such variable characteristics with regard to the length of time of isothermal transformation that an S-curve for each heat of steel may be desirable. In the present work the isothermal transformation of a steel having the following composition and grain size was studied: 0.29 per cent carbon; 0.21 manganese; 0.026 phosphorus; 0.017 sulphur; 0.056 silicon; 1.45 chromium; 3.25 nickel; austenite grain size, 7. The progress of the isothermal transformation was followed by several different methods, including hardness measurements, dilatometer observations, and examinations of the microstructure. It was not expected that these methods would be in precise agreement.3 Accordingly, the changes in microstructure and hardness were given additional weight in determining the initial stage of transformation and the dilatometer measurements were relied on in estimating the completion of the process. The beginning of transformation was indicated by I per cent of transformation products and the end of transformation by about 99 per cent. The reproducibility of the various methods in the ranges of highest sensitivity was checked by several observations at each time and temperature. The steel used in this investigation was annealed for 24 hr, at 925°C. Macroetching revealed no serious segregation. The specimens for the metallographic and hardness investigations were 1¼ by ½ by ? in. Wires attached to the samples were used for handling. instead of tongs, to avoid chilling. The specimens were heated at 845°C. for ½ hr. and quenched into constant-temperature salt baths held at various temperatures from 205&apos; to 650°C. The time required to transfer the specimens was found to be about 1½ sec., and nearly 5 sec. more was required for them to come to the temperature of the bath. After various lengths of time in the constant-temperature baths the specimens were quenched in water at 2I°C. The specimens were cut in half for the metallographic examination, to provide a surface free from decarburization. To determine the beginning and end of the transformation the percentage of transformation determined metallographically and by hardness was plotted against time. A planimeter was used in the metallographic determination. The hardness and metallographic determinations made at room temperature were confirmed reasonably well by dilatometer measurements taken during the process of transformation at the various temperatures. Two dilatometers were used to

Jan 1, 1942