Search Documents

By C. G. Dunn

NUCLEI that are formed during the recrystallization of a grain following plastic deformation generally have orientations that differ from the original. This aspect of recrystallization may be described in terms of orientation changes. It was shown previously, in an investigation on recrystallization in silicon ferrite,1 that the observed orientation changes were highly improbable on a chance basis, and that some mechanism must be involved. Analysis showed that the data could be satisfactorily classified into the smaller of two subclassesf of the 36 third- order twin transformations. No attempt was made at that time to classify the data within the special class of 12 third-order twin transformations, although results did indicate a greater probability for some of them to occur. A classification of this type would be more valuable, of course, with more data on orientation changes per old deformed grain. The present work fulfills this condition to some degree and also extends the scope of the investigation to include the effects of original orientation and the amount of plastic deformation. The effect of original orientation is of considerable interest because of the known effects of orientation on plastic deformation, particularly with regard to degree of fragmentation and the formation of de- formation bands, and because the orientations produced by deformation should influence the orientations obtained through recrystallization. Barrett and Levenson2 reported that single crystals of iron deformed in the range 82 to 97 per cent could be put into three general classes; namely, crystals in class I maintained a reasonably sharp single orientation, those in class 2 transformed into two distinct orientations, and those in class 3 changed into a large number of major and minor orientations. Something similar would be expected for silicon ferrite crystals, and verification of this for a few cases of types class I and class 2 deformation has been reported elsewhere3 for single crystals of silicon ferrite cold-rolled in the range 10 to 20 per cent. As an example of class 2 deformation, it was shown that a crystal of silicon ferrite cold-rolled in a {110} plane in a < 100> direction developed two layers, or deformation bands differing in orientation. When this happens it is possible to etch away one band and leave a single structure for use in studying the orientation changes that occur during recrystallization. when preferred crystal orientations are obtained in recrystallization, it is notparticularly necessary to evaluate groups of common orientation, as was done previously (ref. I, Table 6); but an

Jan 1, 1946

By M. E. Wadswort, A. S. Peck

Infrared data disclose that phenacite reacts with oleic acid to form a chemisorbed oleate monolayer on the mineral surface. The absorption band characteristic of the antisymmetrical C = 0 oleate structure appears at a spectral wavelength of 1623 cm-&apos;. Chemisorption also results in the displacement of OH- and silicate from the mineral surface. Infrared absorbance at 1623 cm-1 is correlated with float-ability at different pH for -60-mesh phenacite particles. Phenacite, Be2SiO4, is an ore mineral often associated with quartz, microcline, and chrysoberyl in pegmatites and mica schist. Experimental phenacite beneficiating processes have been confined principally to the flotation of low grade ores occur-ing in several mountain ranges of Utah and Nevada. The U.S. Bureau of Mines &apos; has recently reported on the separation of phenacite from ore deposits of Mount Wheeler, Nev. Infrared techniques were previously applied by the authors to characterize the role of sodium oleate and oleic acid in the flotation of several non-sulfide minerals.23 A parallel study was projected to the flotation of the orthosilicate mineral phenacite with oleic acid. Infrared spectra provided a &apos;molecular fingerprint&apos; of the mineral surface and permitted identification of the reaction mechanisms. Infrared data were complemented with flotation and chemical tests. EXPERIMENTAL PROCEDURES The experimental procedures used in this investigation, for which data are presented in graphical or spectral form, are described in chronological test order. Phenacite crystals from Mt. Antero, Colo., were obtained from Ward&apos;s Co., Monterey, Calif. The crystals were fragmented in a porcelain mortar to -60 mesh and then pretreated with 0.5 molar HC1 for 15 min to remove iron. Then, the mineral particles were washed free of acid with distilled water and dried. Part of the dried material was ground to a fine powder with a Fisher Grinder using an agate mortar and pestle. Next, the powder was placed in a graduated cylinder and mixed with 500 ml of distilled water. The mineral in suspension was decanted from the settled fraction after 5 min, and the colloidal suspension was used for adsorption tests in which a high specific mineral surface area was required for adsorption and infrared analysis. Conditioning was performed in 50 ml glass centrifuge tubes for both infrared and flotation test determinations. Twenty ml of colloidal suspension was used for the infrared adsorption tests. One and a half g of deslimed -60-mesh HCl pretreated phenacite was added to 20 ml of distilled water for flotation conditioning tests. Six mg of oleic acid was used for each infrared adsorption test, and 0.2 mg of oleic acid was used for the flotation conditioning tests. HCl and NaOH were used for pH modification. The pulps were stirred at a speed of about 1500 rpm for 3 min. Then, the solids were separated out and either dried at 50°C or immediately transferred to a float cell. The pH of the residual liquid was determined with a Beckman Zeromatic pH meter. The flotation procedure is described as follows: 1) A 325-1111 glass micro-float cell was filled with distilled water. 2) Conditioned mineral was placed in the cell and the pulp was aerated through the glass fritted bottom at 7 psi pressure. 3) Floated mineral was skimmed from the cell with a glass slide until flotation ceased. (The end point was reached in all tests in less than 2 min.) 4) The flotation products were dried, weighed, and the recovery was calculated. Samples for infrared analysis were made into mulls using either oleic acid or series 13-21 Halocarbon oil obtained from Halocarbon Products Corp., Hacken-sack, N.J. The mulls were placed between two sodium chloride windows. A characteristic phenacite infrared band at 1868 cm-&apos; was used as an internal standard for quantitative determinations in which absorbance at this position was quantified by the baseline-tangent method4 and related to absorbance at 1623 cm-&apos;. The ratio obtained by dividing absorbance at 1623 cm-&apos; by absorbance at 1868 cm-&apos; was defined as an absorbance quotient for use in graphical presentation.

Jan 1, 1968

By R. B. Toombs

The national and international importance of Canada&apos;s minerals and metals producing industry is reported. The growth of the Canadian industry is traced from 1945, through the period of rapid development of the early 1950&apos;s, to the consolidation and expansion activities of the late 1950&apos;s and early 1960&apos;s. Mineral production in Canada during 1963-including steel, nonferrous metals, and fuels -is reported. It is estimated that by 1970 the Canadian industry will produce $3.9 billion worth of metals, nonmetals, and fuels.

Jan 8, 1964

By V. H. Wilhelm

The trend initiated in January 1936, of stabilized gasoline prices, increased demand and extraordinary drilling activity, continued in California during the year 1937. Crude prices were maintained during the year at the highest level since September 1930. Wildcat activity with resultant new discoveries and development of proven acreage were greater than in any year since 1928. Many fields in California in former years have been produced at full capacity, with consequent loss of reservoir energy, but at the present time continued activity is maintained to develop adequate reserves, so that production in these fields can be taken at a rate to correspond with good operating practice. Naturally, this good operating practice will be influenced to some degree by gas outlets and, in certain instances perhaps, by oil outlets. In any event, these last two controlling features will result in favorable rather than detrimental operation. In fields producing from great depths, ultimate production will be practically limited to the flowing and compressor life of the well, since there is as yet no economical method for pumping wells below depths of approximately 7000 ft. Experience has shown, however, that such pumping difficulties will be overcome and that production secured by pumping will add some to reserves established on the flowing life of the wells. California continued to operate under voluntary curtailment, but with unlimited transfers of allowable between various fields. Even though there was at all times considerable production above the Umpire&apos;s established quota, a constantly increasing demand reduced storage during the year. This increasing demand was due mainly to the rapid rise in Pacific foreign shipments from May to September. It is questionable, however, whether this favorable condition will be maintained over a prolonged period. (See Fig. 1.) Field Discoveries The great drilling activity during the year resulted in the discovery of three new fields in the San Joaquin Valley, as well as many extensions

Jan 1, 1938

By C. A. Heiland

FOR the past three years, the senior writer has carried out, with inter-ruptions, a series of investigations into the characteristics of prospecting seismographs of a wide variety of construction. Early in 1932, a com-plete equipment was developed for both refraction and reflection observa-tions; its first function being, however, the application in reflection shooting. The performance of the equipment proved to be highly satis-factory in a series of field tests&apos; which were carried out by the junior writer, whose services were loaned to the Colorado School of Mines by courtesy of the Plains Exploration Co. in Denver. The various problems that were encountered in the construction of the equipment, in its application in the field, and in the interpretation of the results, are fully treated in Publication 47 of the Department of Geophysics of the Colorado School of Mines. Its first part deals with the various problems encountered in the design of the instruments, and presents a discussion of such topics as the free and forced oscillations of damped and undamped mechanical seismographs, the action of oscil-lographic recording instruments and amplifiers, the characteristics of electromagnetic seismographs, and the requirements of damping, natural frequencies and static magnification for the pickups, amplifiers and oscillographs used in refraction and reflection seismographs. Further-more, a detailed discussion of the various methods of static and dynamic tests of seismic receivers, and a description of the reflection equipment developed at the School of Mines is presented. Unfortunately, a delay has occurred in the publication of the first part of this investigation concerning the instrument problems. There-fore, the second part, dealing with the field problems, is herewith pre-sented first.

Jan 1, 1933

By C. H. Jr. Herty

DURING the past few years frequent reference has been made to a certain type of iron known generally as "bad iron," "dirty iron," etc., both by steelmakers and producers of iron castings.1 Open-hearth operators have claimed that such iron was entirely within the specified limits as to ordinary analysis but it was difficult to make good steel from it. It has been suggested that unreduced material in the iron is responsible, also that most trouble is experienced with the iron when the blast furnace is delivering a product whose analysis is more or less variable. Other reasons suggested are the use of scrap or borings, unsintered flue dust in the burden, a cold hearth, too high a proportion of unsuitable grade of ore, or the form of the carbon in the iron. Accordingly, a subcommittee was appointed at the fall meeting of the Open-hearth Committee of the American Institute of Mining and Metallurgical Engineers held in Pittsburgh in October, 1926, to investigate the reasons for the occurrence of this bad iron and suggest methods for preventing its appearance. This committee enlisted the cooperation of the U. S: Bureau of Mines Experiment Station at Pittsburgh in undertaking a study of pig-iron quality as affecting the open hearth. The following is a report of the findings to date:

Jan 1, 1929

By Eugene McAuliffe

HAVING reached the status of an octogenarian plus, I suddenly decided to take a trip to Great Britain by airplane, before the possibility of hardening of the arteries made such a program too precarious. Of thirty June and July days spent in the islands, five were spent in the south of Ireland, or Eire as the politicians like to call their country. On June 15 I arrived in Glasgow where a day was spent with old friends before moving on to Edinburgh, where the Institution of Mining Engineers was billed to hold its summer session. I had received a cablegram before leaving New York inviting me to attend the sessions which I accepted with avidity, spending three most enjoyable and informative days with old friends and the officers of the Institution, Douglas Hay, president; Ian McDermid, secretary; and members of the council.

Jan 1, 1947

By J. Szekely, J. W. Evans

A formulation is given for radiant heat loss from the surface of molten steel held in a ladle and numerical solutions are presented for the resultant integrodif-ferential equations. The results are shown on plots of the net rate of heat loss against time, with the geometlry, emissivities, thermal properties of the walls, and Preheat as parameters. It was found that the rate of the vadiant heat loss from the exposed metal surface was comparable to the conductive losses from the Portion of the metal in direct contact with the walls. The radiant heat loss was markedly affected by the geometry and by the thermal properties of the walls the net radiant heat loss from the steel could be drastically reduced by providing a top cover and also by the provision of preheat. The results of this work are thought to be relevant to heat loss calculatious concerned with vacuum degassing and with operatzons in which molten metals are held in ladles. WhEN molten steel is held or transferred in ladles heat losses inevitably occur. The accurate assessment of these heat losses is of importance in process design considerations, as the temperature of the metal may have to meet rigid specifications in certain stages of the processing sequence. As shown in Fig. 1, the principal mechanisms responsible for heat loss are: i) Conduction into the walls and ii) Thermal radation from the top metal surface (possibly augmented by natural convection) The conductive heat loss may be readily calculated as much information is available in the literature on both the general theory1&apos;&apos; and on its particular applications to ladle heat loss calculations. Evaluation of the radiant component of the heat loss is less straight-forward. In two recent papers it has been shown that the presence of a slag layer 2 to 3 in. thick would prevent any significant heat loss for periods up to an hour,5&apos;" however, should bare metal be exposed, constituting the radiant surface, substantial heat losses could occur. This latter case is of considerable practical interest in various degassing operations and in the vacuum processing of certain specialty steels, where the top surface of the metal is not covered by a protective slag layer. Under these conditions a substantial radiant flux is emitted by the top metal surface; part of this flux leaves the system, part of it falls in the ladle walls. The radiant flux incident on the ladle walls is in part absorbed and conducted away, and in part reflected and re radiated. The purpose of the paper is to present a general formulation of the problem, the resultant solution of which should enable computation of the net radiant heat loss from the metal surface. The principal variables, the effect of which will be investigated, include initial metal temperature, geometry, thermal and radiative properties of the wall, and various modes of preheat. FORMULATION Consider a cylindrical enclosure, shown in Fig. 2, with a diameter D, height H, and wall thickness W, the cover at the top of the cylinder having a wall thickness L. If the temperature of the base (representing the top surface of the metal) is kept constant, say, Tb, the problem is to calculate the net rate of heat loss from the base as a function of time, geometry, the initial temperature distribution, and the thermal properties of the system. As customary, the formulation will consist of the mathematical statement of the conservation of thermal energy within the system.

Jan 1, 1970

By W. V. Vietti, W. A. Oberlin

Crude petroleum produced in the Texas Panhandle oil field is both an asphalt and a paraffin-base oil and is further characterized by being a high-gravity crude with an extremely high cold test,. An eight-well composite of Panhandle crude showed the following characteristics: Gravity, 36.6° A. P. I. Viscosity: 61 sec. Saybolt at 100° F. 170 sec. Saybolt at 75° F. 1560 sec. Saybolt at 50° F. (stirring) Cold Test, 60° F. Distillation Test: Per Cent. Per Cent. Gasoline........................ 28.8 Wax........................... 19.2 Kerosene........................ 4.8 Asphalt........................ 13 .0 Gas oil......................... 30.7 Sulfur1......................... 0.8 Fuel oil......................... 34.7 Subsurface Conditions The original pressure in the formation in the Panhandle field closely approximated 420 Ib. gage or 435 Ib. absolute pressure. Temperatures taken indicate that the formation temperatures do not exceed 90° F. The temperatures in Table I are typical measurements taken on one lease. * A contribrition from the research department of the Marland Refining Co. of Oklahoma and the production engineering department of the Marland Oil Co. of Texas. 1 Smith [Analysis of Panhandle and Rig Lake Crudes. U. S. Bur. Mines, Circular No. 6014 (December, 1926)] found an average sulfur content of 0.6 per cent.

Jan 1, 1928

President MRS. REED W. HYDE 84 Mountain Ave. Summit, N. J. First Vice-President MRS, WILLIAM A. SCHEUCH Trent St. Great Kills, S. I., N. Y. Second Vice-President MRS. THORNS E. LLOYD Box B Netcong, N. J. Third Vice-President MRS. H.. T. HAMILTON 24 Ridge Rd. Summit, N. J.&apos; Fourth. Vice-President MRS. R. A. PALLANCH 1342 Laird Ave. Salt Lake City, Utah

Jan 1, 1939

Dec. 2, American Mining Congress, annual membership meeting, University Club, New York. Dec. 2, Society for Applied Spectroscopy, Socony-Vacuum Training Center, New York City. Dec. 4-6, AIME, Electric Steel Furnace Conference, Hotel William Penn, Pittsburgh. Dee. 5, Atlanta Meeting of Southeast Section, AIME, Ansley Hotel, Atlanta. Dec. 7-10, American Institute of Chemical Engineers, annual meeting, Hotels Cleveland and Carter, Cleveland. Dec. 8, AIME, Arizona Section, all-day meeting, Tucson. Jan. 6, 1953, Society for Applied Spectroscopy, Socony-Vacuum Training Center, New- York City. Jan. 14, 1953, AIME Connecticut Section, Hammond Metallurgical Laboratory, Yale University, New Haven, Conn. Jan. 14-16, 19th Annual Meeting of Society of Photogrammetry, Shoreham Hotel, Washington, D. C.

Jan 1, 1952

By John K. Kennedy

ThE basic equations describing continuous zone-melting via the zone-void method were reported by Pfann. Using these equations, a theoretical study was undertaken in this laboratory on the effect of the variation of the significant parameters of the zone-void system. These parameters are the zone length, 1, the heater length, h, and the effective distribution coefficient, k. The object of this study was to determine the effect of these parameters on and (where a = Cp/Cf and ß = Cw/Cf, Cp, C,, and Cf being, respectively, the solute concentration in product, waste, and feed) so that, in future application of this technique to the ultrapurification of materials, the effect of 1 and h would be predictable regardless of the value of k. The basic assumptions made by pfannl were, for the purposes of this study, assumed to hold. For k < 1, the steady-state solute distribution in the stripping section and the shift in this distribution brought about by passage of a void is shown in Fig. 7 of Ref. 1. In this section the definition of k and ß precludes the possibility of ß assuming values less than unity when k < 1. In the course of this investigation it was found that computations based on Pfann&apos;s equations gave values of ß less than unity in the region 1 > k > l/h for almost all values of Ls, where Further computations showed that 6 assumes negative values when k > 1 for many values of L,, 1, and h. A check of the derivation of the stripping-section equations showed that an error had been

Jan 1, 1964

Jan 1, 1934

By M. S. Seltzer

High temperature steady-state creep rates have been determined jor lead sulfide single crystals whose defect concentrations were fixed by equilibration under controlled sulfur pressure. The activation energy of creep, Qc , for undoped lead sulfide, is a function 01 composilion, decreasing from 2.9 to 2.2 ev as the carrier concentration increases from 9 x 1016 to 8 1018 electrons cm-3 for lead excess crystals, and increasing from 1.7 to 2.3 ev as the concentration of holes increases from 4 x 1017 to 1 x 1018 cm-3 in sulfur excess material. For five different composilions, Qc for undoped and bismuth-doped crystals has been found to be equal to Qpb + Qs, the self-diffusion activation energies for lead and sulfur in PbS. It is well-established1 that high-temperature steady-state creep of pure metals is a diffusion-controlled process, where the activation energy of creep is equal, within experimental error, to the activation energy of self-diffusion. The relationship between the activation energy for steady-state creep and those for self-diffusion in binary compounds is more complicated, however, because two different diffusing species must be considered, and becayse the activation energies may be influenced by compositional variations and by foreign atom additions.2-4 In some cases experimentally determined creep activation energies are correlated with those for self-diffusion of the slower-moving species, but such agreement is by no means universal. Interpretation of experimental results is difficult because few investigations include measurements of creep rates and self-diffusion coefficients of both diffusing species on single crystals of similar composition and foreign atom concentration. The objective of this investigation, therefore, is to determine the influence of stoichiometric defects and foreign atoms on steady-state creep and self-diffusion for a well-characterized binary compound. Lead sulfide, a compound semiconductor which crystallizes in the NaC1-type structure, and whose homogeneity range includes compositions on either side of the 1:l atom ratio, was chosen for study in this investigation. The pressure-temperature-composition relations for PbS are available,5,3 and deviations from stoichiometry may be monitored by electrical measurements.7 Single-crystal specimens are available to allow observation of effects due to bulk phenomena without interference from grain-boundary effects. These crystals have been employed to determine steady-state creep rates under compressive stress for "pure" and bismuth-doped PbS as a function of sulfur pressure and temperature as well as crystal orientation and applied stress in order to establish the relationships between defect concentrations and creep rates. EXPERIMENTAL PROCEDURES Crystal Growth. Lead sulfide crystals, prepared by the Bridgman method, are grown in evacuated quartz crucibles, filled with almost equal atomic proportions of high-purity (99.999 pct) lead and sulfur, and heated to a temperature above the melting point of PbS (about 1127°C) so that the lead and sulfur react to form molten PbS. The crucible and melt are dropped through the hot zone of the crystal-growing furnace at the rate of 1 cm per hr. The maximum melting point of PbS is slightly on the lead-rich side of the 50:50 composition; hence crystals grown from a near stoichiometric melt are usually n-type semiconductors containing excess lead atoms. Typically the lead excess concentration in solid solution with the PbS is 3 x 1018 atoms cm-3. Crystals containing either 1/20 or 1/2 mole pct Bi2S3 were prepared by addition of the foreign atoms prior to crystal synthesis. Preparation of Specimens of Controlled Stoichiom-etry. Since it is difficult to grow crystals of desired composition, the process of crystal growth and control of stoichiometry are separated into two distinct operations. Equilibration of as-grown PbS to a desired composition is most easily accomplished by first annealing the n-type crystals under high sulfur pressure (about 1 atm) at temperatures above 700°C. This process serves to put excess lead precipitates into solution, yielding 0 -type crystals upon quenching to room temperature. Inter diffusion occurs readily in crystals so treated, and the methods described by Bloem may then be employed to obtain crystals of controlled stoi-chiometry. For the creep measurements made in this study, this involves heating crystals in mixtures of H2 and H2S The equilibrium constant for H2S is given by: Thus the sulfur partial pressure is obtained from knowledge of the H2/H2S ratio and Kh2S for the temperature in question. Fig. 1 shows the p-T-x diagram for PbS. It can be seen that, within the stability limits for single-phase lead sulfide, desired compositions may be obtained by equilibrating under a specified sulfur pressure and temperature. Characterization of Crystals. The principal methods for evaluating PbS crystals include measurement of electrical properties and mass-spectrographic analysis. The measured electrical parameters include Hall coefficient, conductivity type, and electrical resistivity Bloem7 has shown that there is a 1:l relation between the defect concentration and carrier concentration obtained. Hence, if the contribution to the carrier con-

Jan 1, 1968

By James W. Malcomson

The Tigre Mining Co. of Mexico, owned by the Lucky Tiger Combination Gold Mining Co. of Kansas City, decided early in 1910 to enlarge its mill, which consisted of a concentrator milling 3,000 tons of ore per month. The enlarged plant was designed to crush and concentrate 6,000 of ore and to cyanide 7,500 tons per month. The extra tonnage cyanided was to be obtained from tailings which were stored below the old mill. Power was supplied to the old mill from four boilers; a 150-h-p. Corliss engine and two Weber 60-h-p. gas-engines using producer-gas made from charcoal. The total horse-power required, including 60 h-p. used for machine-drills in the mine, was approximately 275. Cord-wood cost $4.32 per cord, 8 by 4 by 3 ft., and charcoal $15 per ton. The fuel supply in the surrounding country was approaching exhaustion; more than 150 mules and 50 men were engaged in cutting and transporting this fuel, and the unsettled political conditions in Sonora were such that it would be practically impossible to keep an organization of this kind together. The price of fuel was steadily rising and at times it became almost impossible to get sufficient fuel to operate. It was estimated that the enlarged plant, together with the mine, would require 750 h-p., as follows: Horse-Power. Old mill, which was left unchanged,..............180 New concentrator,.......................90 Cyanide-plant,........................380 Mine and other requirements,................. 100 Total,........•..................750 In a study of the best manner to obtain power the following alternative propositions were considered:

Jan 1, 1914

By R. L. Orr, J. D. G. Masse, Ralph Hultgren

The relative partial molar enthalpies of gold and tin in liquid Au-Sn alloys have been measured from Xsn = 0.474 to 0.510 at 696°K, slightly above the melting point of solid AuSn. Within an average precision of 6 cal per g-atom, the data are represented by two smooth curves, which satisfy the Gibbs-Duhem relationship and which do not show any anomalous behavior in the range of composition studied. The results give no support to the hypothesis that atomic associations in the equiatomic liquid alloy resemble those in solid AuSu. LITTLE has been firmly established as to the nature of atomic distribution in liquid metallic phases. A favored hypothesis assumes the existence of atomic groupings in the liquid phase which are similar to those in solid phases occurring at lower temperatures. Beginning with this hypothesis, it is often possible to adjust the values of certain parameters (such as degree of association) so that approximate agreement is achieved with certain features of the X-ray diffraction pattern of the liquid, even though many other possible structures might satisfy the data equally well. Thus, in this manner, the structure of liquid tin has been described as a dispersion of fragments of gray tin in a matrix of metallic tin.1 Four X-ray diffraction studies2"5 have been made of the liquid alloy of composition AuSn at temperatures slightly above the melting point of the solid. Each investigator concluded, on somewhat different grounds, that the liquid consisted to a large extent of arrays of atoms similar to the solid, with admixture of more disordered arrays. Solid AuSn has the nickel arsenide crystal structure: each tin atom has six nearest neighbors, all gold atoms; and each gold atom has six tin and two gold atoms as nearest neighbors. It remains highly ordered to the melting point. The liquid alloy has a large exothermic (?H700° K = -2700 cal per g-atom6) enthalpy of formation, favoring ordering and making the hypothetical molecular association not unreasonable. The possible existence of such solidlike arrays, or of a high degree of order that occurs preferentially at a specific composition in a liquid alloy, might also be revealed by thermodynamic behavior somewhat analogous to that in highly ordered solid alloy phases. The latter often exist over wide composition ranges, within which the highest degree of order occurs at the ideal composition for which the atomic fractions are equal to the fractions of sites which are "right" for each kind of atom. On departing from the ideal composition, the excess atoms occupy "wrong" positions, raising the internal energy and making it progressively easier for additional atoms to occupy "wrong" positions. Thus, on either side of the ideal composition, there should be a pronounced rise in the entropy and enthalpy, which would be shown particularly by the change in the relative partial molar enthalpies, ?Hi, since they depend strongly on d?H/dx. In the one case where accurate measurements have been made, the solid AuCu ordered phase, the structure becomes much less ordered as the composition deviates from the ideal, and relative partial molar enthalpies change sharply as shown by the data6 given in Table I. This suggests the possibility of finding similar pronounced changes in the relative partial molar enthalpies of gold and tin in liquid alloys near the composition AuSn if the postulated solidlike ar-

Jan 1, 1967

By E. T. Turkdogan, L. S. Darken, R. J. Fruehan

Further consideration is given to the application of the quadratic formalism to evaluate the thermodynamics of binary metallic solutions from experimental data. The use of the thermodynamic relation, in(r1/r2) dN2= 0, in the evaluation of activity data is discussed. The empirical correlations derived previously for enthalpies and entropies of solutions in Part II are shown to be predicted theoretically for a special case. The applicability of the quadratic formalism to the activity coefficients for binary organic solutions is demonstrated. DARKEN&apos; introduced a quadratic formalism describing the composition dependence of the activity coefficient in the terminal regions of binary metallic solutions. In a subsequent paper (Part II) Turkdogan and Darkeen2 extended this formalism to the enthalpy and excess entropy of binary metallic solutions, and showed that the available data for the activity coefficients and heats of mixing of many solid and liquid binary metallic solutions confirm reasonable applicability of the quadratic formalism. Much variation was noted, however, in the extent of the terminal regions from one system to another, commonly from about 10 to 70 at. pct. For the present purpose, equations derived previously need be given only for one of the terminal regions, e.g. region (I), 0 < N2 < N&apos;2: where subscripts 1 and 2 indicate quantities for components 1 and 2 and superscript ° the values at infinite dilution; other terms are: N = atom fraction, y = activity coefficient, = partial molar enthalpy of solution, ?HM = molar heat of solution, ?Sx = excess partial molar entropy, ?Sx = excess molar entropy. The heat and entropy like terms (constants) el, and S12 are defined in the following expression for the temperature dependence of a12, thus a12 £12 — s12 rnl 2.303RT 2.303 R l J Using this formalism, the thermodynamics of binary systems in the terminal regions may be described over a temperature range of experisental interest in terms of eight quantities: Lº1—Lº2, ?Sx1,?Sxº2 , £12 ,£21,fiai, S12, and S21. In the previous paper, these quantities were evaluated for many solid and liquid binary solutions, and two significant correlations were observed between these thermodynamic quantities pertaining to the terminal regions, thus [10] and [11] Combining Eqs. [9], [l0], and [ll] and rearranging gives a12 -a21 = 1.382R log rº2- 0.08(?S2xº- ?S1xº) [12] Since the second term involving entropies is small and Eqs. 1101 and [ll] are empirical relations, the above equation may be simplified to a12 = 2.74 log rº2 [13] Using the values of a&apos;s and y°&apos;s compiled in Parts I and 11, a12 - a21 is plotted against log(rº2/rº1) in Fig. 1; the line drawn has a slope of 2.74. For Hg-K at 300°C, log(yº2 /yº1)= —5.10, not shown in Fig. 1, and from correlation [13], a12 - a21 = -13.97; this is to be compared with -10.76 derived from the activity data (Part II).

Jan 1, 1970

By AIME AIME

AT a recent meeting of the Utah Section. A.I.M.E., P. D. Nielson, general plant superintendent of the new Geneva steel plant at Provo, Utah, spoke on "General Operations of the Geneva Plant." Mr. Nielson explained that the plant was located at Provo, Utah, on account of railroad facilities, the proximity of coal, iron, and limestone, and the nearness of water for operating the plant. Water probably was the most important item in making the decision.

Jan 1, 1944

By B. R. Banerjee

MATERIAL used throughout this investigation was high-purity aluminum (99.998 pct). The 1/2-in. cubes were cut out of a cold-rolled slab and annealed at 550°C for 1 hr before deformation. The single crystal specimen was 1 in. in diam x 0.33 in. thick, cut from a cylindrical crystal produced by cooling at about 55°C per hr in a furnace which had a convenient gradient of about 10°C in every 4.5 in. vertical crucible length. Specific data on the ten specimens studied are summarized in table I. Three types of deformation were employed: (I) compression in a hand-operated hydraulic press; (2) impact with a 7-lb sledge hammer; and (3) rolling, using a wedge-shaped specimen&apos; to obtain a gradient of deformations varying from 0 to 50 pct along the length of the wedge. Specimens were either deformed at room temperature, or first cooled in a freezing mixture of dry ice and ether at a temperature of —72°C and then deformed between steel blocks cooled with dry ice. The specimens deformed at the low temperature were ground and polished through 000 emery paper and wheels impregnated with alundum and alumina No. 1. During this entire procedure the specimens were dipped frequently in the freezing mixture of dry ice and ether in order to maintain constantly a frosty surface as insurance against overheating. All specimens were given a final electrolytic polish, using two different electrolytes* to insure that the surface effects observed were not char- acteristic of the polishing technique. With both electrolytes, the annealed specimens gave even surfaces with good polish. Several standard etchants were tried without success. The best results were obtained with an immersion etchant, developed in this connection, containing: hydrofluoric acid, 4 parts; nitric acid, 1 part; glycerine, 3 parts. Discussion of Results Typical strain markings have been observed within deformation bands, as shown in figs. 1, 2, and 4. By stereographic plotting of metallographic measurements, the strain markings within a deformation band in a single crystal of aluminum deformed by compression were found to be traces of (111) planes within a maximum scatter of 6". The edges of the deformation band were found to be traces of the (100) planes also within the maximum scatter of 6" (in agreement with previous workers). At 30 pct deformation, this scatter was considered quite normal because of the fragmentation and rotation of the crystal. This solution, based on the traces on one plane of observation is not unique, but as the planes were observed to be those normally and logically to be expected, further work in this regard was not felt to be necessary. The study of strain markings in a wedge-shaped specimen, rolled to obtain a gradient of deformation from 0 to 50 pct, revealed prominent strain markings at 25 pct reduction in thickness (fig.5). Faint and weak strain markings were visually observable up to a minimum reduction in thickness of about 12 pct. Since strain markings have been observed in other face-centered cubic metals after much smaller deformations;1, 2 and since the rate of recovery in aluminum is high, it is believed that, at lower deformations, self-recovery removes the localized strains at the slip interfaces, thus removing the source of the etching effects that give rise to strain markings. At high magnifications, strain markings sometimes seem to appear as very thin, light-banded re-gions bounded by a pair of dark edges. This so-

Jan 1, 1951

By A. D. Hughes

A relatively small area in Malaya, about 200 miles long by 40 miles wide, is the most important source of tin in the world. Some tin is recovered in other parts of the peninsula. Of the tin mined, 98 pct is recovered from alluvial deposits. From 1935 to 1941 the average annual world production of tin was 190,000 tons. The average annual production from Malaya during the same period was 62,000 tons or about one third of the total. Other producing countries, in order of importance, were the Netherlands East Indies 34,000 tons, Bolivia 30,000, Belgian Congo, Nigeria, Siam, Burma, China, and a few others with smaller amounts. The serious shortage of tin during the war period was due to the fact that the Japanese were occupying Malaya, Netherlands East Indies, Siam, Burma, and China which, together, formerly were producing 65 pct of the world supply.

Jan 1, 1949