Search Documents

By J. E. Ryan

TRONA, Calif., is a miniature urban community of some 3500 people, located on the northwest shore of dry Searles Lake in the extreme northwest corner of San Bernardino County, approximately 186 miles north and east of Los Angeles. Since it is situated on the Mojave Desert, a typically desert climate prevails with wide variations in temperature between day and night, extreme daytime summer heat, and cool to cold winters. Rainfall averages somewhat less than 4 in. per year, and dust storms are common. The rate of evaporation, .however, is great, amounting to 6 to 9 ft of water per year. The extremely low humidity makes the summer heat of 110°F tolerable with only a mild, temporary discomfort. Nature of Deposit During the periods when Searles Basin was flooded, the waters that passed through Indian Wells Valley spread out to form a broad, shallow lake providing, in effect, a settling basin for suspended sediment. The drainage into the deeper and more isolated Searles Basin thus was clarified to a great degree before concentration began. Today, the elevation of the dry surface of Searles Lake is 1618 ft, and the salt deposit measures 5x7 miles. At the eastern and northeastern margins of the main playa zone and just at the foot of the alluvial slope of sand and coarser wash from the Slate Range mountains, a rim of crusted salts rises a few feet above the level of the flat. The deposit is a saline efflorescence composed of salts that were presumably brought up with rising ground waters to be deposited at the surface by solar evaporation. This deposit consists chiefly of trona, and it is after this Trona Reef that the town Trona was named. Strip mining operations have been conducted in the past at infrequent intervals for the recovery of crude trona salts. The main focal point of interest in Searles Lake from a commercial standpoint is the main salt body located almost centrally in the basin. The exposed portion of this porous saline deposit covers approximately 12 sq miles and averages 71 ft deep. Its interstitial voids, which constitute 50 pct of the total volume, are permeated with a brine, which is in equilibrium with the soluble salt deposits. The brine is the raw material for the operations of the American Potash and Chemical Corp. plant at Trona, shown in Fig. 1. The soluble salt deposits are of interest for their potential values in future technologic development. The brine, which is stratified according to slight differences in density, stands usually within 6 in. of the surface of this exposed, firm, salt body. The surface is usually dry and will support the weight of heavy mobile units and drilling equipment. Occasionally, however, surface waters from the higher watersheds encroach upon the main salt body during infrequent periods of precipitation on the surrounding mountains. This water dissolves surface salt, becomes a dilute brine, and has been observed to stand as high as 18 in. above the salt surface when undisturbed. Windstorms will shift the water back and forth across the lake surface. The exposed salt body is surrounded by additional submerged areas of commercial soluble salt deposits covering some 20 sq miles, hidden from view by marginal playa mud. These vary in depth up to as much as 30 ft. Thus, the outline of exposed and submerged salt deposits of commercial value is estimated to cover a total area of 32 sq miles, which is roughly circular but slightly elongated from northwest to southeast. It has been estimated that each square mile contains about 100 million tons% f alkali salts. The results of drill borings in the past 15 years have brought to light the interesting fact that the main salt body lies superimposed on an impervious mud deposit from 10 to 15 ft thick containing relatively little soluble salt. Under this deposit lies a second soluble salt body 35 ft deep. The lower salt body is interspersed with numerous insoluble mud lenses and its composition is considerably different from that of the primary, or main salt deposit. Recent drill borings have not penetrated beyond 300 ft. They have, however, revealed that underlying the lower salt body, the mud sediments carry deposited minerals of trona, nahcolite, mirabilite and much less soluble carbonates or sulphates of calcium and/ or magnesium. This structure is shown in Fig. 2. Current Lake Survey Program Several hundred holes have been drilled in the deposit. However, to carry out a thorough and carefully correlated study of the composition of the soluble salts and other minerals in the dry lake basin, a drilling program was inaugurated recently and is now nearing completion. In this survey, pattern drill holes are sunk at regular lh-mile intervals to a depth of approximately 150 ft. Drilling equipment consists of a No. 51 C. P.

Jan 1, 1952

By Evan Just

DIRECT subsidies for mine production in this country began as an outgrowth of wartime 'price regulation. The price-fixing authorities realized that the volume of production to be required from domestic copper, lead, and zinc mines would invoke costs of production considerably higher than the established ceiling prices. Accordingly, beginning Feb. 1, 1942 the Premium Price Plan was set up, which undertook to pay premiums to mines for production in excess of quota, of 5¢ per lb of copper and 2Y4¢ per lb of zinc or lead. Quotas, except for small mines, were initially established at the average rate of production in 1941, but were later reduced arbitrarily on an individual basis. Subsequently, additional "B" premiums were set for lead and zinc of 2Y40 per lb and a further "C" zinc premium of 2%¢. Additional copper premiums were negotiated on an individual basis, mainly with small mines. Quotas under each of these successive categories were the production obtained at the next lower premium level. In other words, under ceiling prices of 12¢ for copper, 6,14¢ for lead, and 83¢ for zinc, it was possible for high-cost operations to receive prices plus premiums of 17¢ or more for copper, 12¢ for lead, and 16% 0 for zinc on a portion of their production. On the other hand, some of the larger operators received only slight premiums and in at least one instance none at all. The average price plus premium for copper was 12.25¢ in 1942 and rose to 13.65¢ in 1945. That for lead was 6.99¢ in 1942 and 8.73¢ in 1945, and for zinc it was 9.06¢ in 1942 and 11.200 in 1945.

Jan 1, 1948

By S. M. Shelton

SINCE the Saar started. the real progress in scrap-metal recover is in the change of point of view regarding secondary metals. The tendency had been to regard scrap as the normal outgrowth of obsolescence, fluctuating somewhat from periods of depression to periods of prosperity. but nevertheless an unwieldy economic factor more to be contended with than embraced. Now, metals above the ground are being looked upon as semi-permanent reserves or stock piles in various stages of repeated use or revolving life cycles. The change in point of view is due to the forced realization that domestic supplies of new metals are limited and many foreign sources are at least temporarily closed. The stock piles must be cultivated. The reserves must be made more nearly permanent. Steps are being taken : (1) develop methods for recovery of scrap metals heretofore not recovered, and (2) restrict strategic metals to uses ensuring a large percentage of re-use, which in turn means substitute materials in the dissipative uses.

Jan 1, 1942

EXECUTIVE COMMITTEE OF THE BOARD OF DIRECTORS W E WRATHER, Chairman A B KINZEL -EARLE E SCHUMACHER DONALD H MCLAUGHLIN - JOHN R SUMAN FINANCE COMMITTEE OF THE BOARD OF DIRECTORS ERLE V DAVELER, Chairman PHILIP KRAFT - CLYDE E WEED

Jan 1, 1952

FOR this Famous Mining Enterprise issue MINING ENGINEERING selected the company that started the zinc in dustry in the United States. The New Jersey Zinc Co. has been a supplier of zinc products to the nation's industries for more than 104 years. Its Horse Head trade mark is famous throughout the world.

Jan 12, 1953

By Campbell Hunter

PETROLEUM is found in almost every province in Persia. On the northern frontier, along the southern shore of the Caspian Sea, it is found near Anzelli and Shakhtesar and gas at Khoremabad. Oil is also found at Gumush Tepe, northwest of Astrabad, on the southeastern shore of the Caspian Sea. Further inland, to the south of Astrabad, oil is found at Schahkuh-i-balae, also on the margin of the Khorasan desert at Semnan, 115 mi. (35 m.) east of Teheran. Along the western frontier, from northwest to southeast, oil is encountered at Ouschachi, north of Lake Urumieh; in the province of Azerbaijan, at Zohab, Khanikin, and other places in the district of Kormanshah in the province, of Ardelan. Further south, in the province of Luristan, oil is found east of Mendeli and in the Pusht-i-kuh districts. Considerable quantities of oil are also obtained from Schuster, Maidan-i-Naphtun, Ram-Hormuz, Beheban, which are almost on a straight line, running northwest and southeast along the foothills of the Bakhtiari Mountains. At Ahwaz, in the province of Arabistan, oil has been found along another range of hills whose axis also lies in a northwest-southeast direction. In the Fars province, boring for oil has taken place at Daliki, and indications of oil are found at Kheri, Fasa, Darab, and other places. A gas show is also recorded at Kuhi-Sung-Atush in this province, 30 mi. (48 km.) east of Darab. In the south of Persia, oil is encountered on. Qishm Island, also at Ahmedi and other places north of Bunder Abbas. On the southeastern frontier, oil is found on the Sarhad range of hills. Thus, oil indications have been noted over a distance of approximately 1100 mi. along the western and 700 mi. along the northern frontiers of Persia.

Jan 2, 1920

By R. B. Adair, J. S. Browning

The laboratory batch and continuous flotation pilot plant tests demonstrated the technical feasibility of recovering high grade mica concentrates from weathered mica pegmatite ores of Alabama and Georgia. The research indicated that combinations of anionic and cationic collectors may be used effectively for flotation of fine size mica from weathered pegmatite ores. In continuous tests, concentrates containing 98.5% mica were obtained from the Georgia pegmatite ore; the Alabama pegmatite ore concentrates contained 98.4% mica. The recoveries were 91 and 89% respectively. INTRODUCTION The principal uses of fine ground mica are as a filler in wallboard joint cement, as a filler and surface coating for roofing, as an ingredient in paints, and in oil well drilling mud. The mineral has other uses in the manufacture of rubber, wallpaper, plastics, welding rods, electric insulation, house insulation, and textiles, and as an annealing agent in metal treatment. In recent years, more than 99% of the domestic mica produced has been scrap and flake mica (mica which does not meet specifications for sheet mica and is used for producing fine ground mica). There has been a continued increase in mica production for several years, the 1963 production of scrap and flake mica totaling 117,251 tons.1 Ground mica is obtained primarily by crushing and milling pegmatites and schists. To a lesser extent, mica is produced as a byproduct of kaolin washing and feldspar and spodumene flotation operations. The processes used in recovering mica by crushing and milling pegmatites are generally simple, consisting of various combinations of alternate roll crushers and trommel screens that separate the mica and gangue at screen sizes coarser than 6-mesh. As these processes are designed to recover only coarse mica, high losses in the plant rejects are common. Large tonnages of tailings from the crushing and screening plants have been accumulated in a number of areas. Methods for treating such products were developed by the Bureau of Mines in 1941,2 but have not been generally applied. More recently, mica flotation research has been completed and published by the Bureau of Mines.3 These methods required complete removal of 150- to 200-mesh materials from the flotation feed with consequent fine mica losses. Later, the Bureau of. Mines investigated methods for-recovering fine size mica from pegmatite ores after desliming sufficiently to remove clay materials, but not so drastically as to remove the fine sands. This report summarizes the results of these studies. The process developed was effective on pegmatite ores from two locations and should be applicable to the commercial treatment of other mica-bearing pegmatite ores and fine rejects that have been accumulated at various mica-milling operations. DESCRIPTION OF ORES The ores used in the investigation were obtained from the Dixie Mines, Inc., Heflin, Alabama, and the Ruberoid Corporation, Hartwell, Georgia. The sample from Alabama contained muscovite and quartz, with a high percentage of clay, and minor amounts of biotite, kaolin, limonite and tourmaline. The mica in the ore was essentially all minus 4-mesh in size and was free of attached mineral grains. The Georgia sample contained muscovite and quartz, with minor amounts of biotite, kaolin, and limonite. The mica in the ore, which was essentially all minus 4-mesh, was liberated. Petrographic analyses of the two samples are given in Table I. THE ANIONIC-CATIONIC MICA FLOTATION METHOD Previous investigators2,3 have reported that complete desliming of mica ores at 150- to 200-mesh was required prior to flotation with cationic collectors to obtain satisfactory selective separation of the mica from the other mineral components. Numerous tests were made at the Tuscaloosa Metallurgy Research Center to determine if some reagent combination could be used to selectively float finer size mica without complete desliming. The investigation led to development of a process using a simple reagent com-

Jan 1, 1967

H. Van F. Furman, Denver, Colo. (communication to the Secretary): There are some statements in Dr. Carpenter's interesting paper which appear to require explanation, if not modification.

Jan 1, 1901

By James E. Lawver, James L. Wright

This paper discusses the design and calibration of a Faraday pail for measuring electric charge. The paper also shows that at least for two minerals, quartz and calcite, the phenomenon that Johnson termed "reversibility" can be explained in terms of the contact electrification between the minerals and the metal rotor of an electrostatic machine. Each year the free world produces about 13 million tons of mineral concentrates by electrical separation. However, despite the rather general acceptance of electrical concentration as an industrial process, research in this area has lagged far behind the efforts devoted to competitive processes such as froth flotation. The purpose of this paper is to describe the design and calibration of a Faraday ice pail for measuring charge density on mineral grains and to show some of its applications in the area of electrostatic and electrodynamic research. THE DESIGN AND CALIBRATION OF FARADAY PAILS FOR ABSOLUTE CHARGE MEASUREMENT The electric charge on mineral grains at a given time during an electrical concentration process is de- pendent on many factors and cannot, in general, be accurately calculated a priori. It is thus important to devise a method of measuring absolute charge. One method of measuring electric charge is to note the potential rise of an electrometer when charged particles drop into a Faraday pail. Two types of Faraday pail have been constructed and calibrated. The first type, Faraday Pail I (Fig. 1), is a vertical pail originally designed to measure the charge due to contact electrification between mineral grains and a metal rotor or due to conductive induction when mineral grains are passed over a rotating cylinder in the presence of an electric field. The second type, labeled Faraday Pail II (Fig. 2), is a horizontal pail designed to determine the charge distribution of mineral grains after they pass through the separating zone of the electrical concentrator shown in Fig. 4. The main advantage of the horizontal pail is its low head-room requirement and the long opening which enables the experimenter to sample the entire width of the stream of minerals being separated. The Faraday pails were calibrated in the following manner: A calibration head was constructed in the form of a hollow brass sphere that could be held in an insulated metal cylinder by vacuum (Fig. 1). The capacitance of the sphere was calculated by measuring the capacitance of the sphere and cylinder combined and that of the cylinder alone and subtracting the latter measurement from the former. The sphere was then charged to a known potential (V) and allowed to drop into the Faraday pail which was attached to a Keithley Model 610A electrometer. This instrument has an accuracy of 2% full scale and has

Jan 1, 1969

By C. H. P. Lupis, R. Hocine, G. Bernard

The necessary and sufficient conditions for the stability of a multicomponent phase with respect to infinitesinzal fluctuations are derived and transformed to be written in terms of activity coeffcients and mole fractions rather than in terms of the customary second deritlatives of the free energy. NECESSARY conditions for the stability of a multi-component system were derived by Gibbs as early as 1876.' However, as the usefulness of these conditions is greatly enhanced by the simplicity of their translation in terms of functions of common usage, the present contribution establishes these conditions in terms of activities or activity coefficients-and mole fractions. It was shown in another article2 that not only may these conditions be used for the prediction of the appearance of new phases, but they may also provide a check on the orders of magnitude of the interaction coefficients involved. "Spinodal" decomposition is said to occur when, at constant temperature and pressure, the system is unstable with respect to infinitesimal fluctuations in composition. As a result, the "phases" which appear may be attained through continuous changes in the system rather than discontinuous ones, and, consequently, the free energy of these phases may be described by a unique continuous free-energy function. For a binary system, the familiar curve of Fig. 1 illustrates the case we wish to extend to a multicom-ponent system. The conditions to be written pertain to the decomposition of a system of n moles into moles of phase moles of phase v, ...hen moles of phase 9, where the phases a, ...v, ...9 are—at least initially-arbitrarily close in composition to that of the original phase. Each A, is positive and since the total number of moles n in the system remains constant: Each phase v contains hv(nl +dnY) moles of component (I), ...xV(ni +dny) of component + dnk) moles of component (m). The total number of moles ni in the system remaining also constant, it is clear that:

Jan 1, 1968

By S. L. Hoyt

ABOUT three years ago eight standard steels were prepared for the cooperative investigation of methods for oxygen analysis, sponsored by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers and by the National Bureau of Standards. A preliminary report of the results was made at the annual meeting of the A.I.M.E. in February, 1936. ? This report showed the reliability of vacuum-fusion methods and further brought out certain advantages of the fractional vacuum-fusion method. The results obtained by the authors with the latter method will be discussed here, with some com-ments on the procedure for those who are interested in determinations of gases in steel. Some additional comments are offered on the use of the polarizing microscope for identifying the inclusions in the steel to check and amplify the findings of the fractional vacuum-fusion analysis. For details of the fractional method, see the paper by L. Reeve1.

Jan 1, 1937

By Thomas J. O’Neil

During the past five years, the mining industry has been subjected to new operating constraints that are unprecedented in number, scope, and urgency. The industry must operate in a safer, cleaner manner, yet produce more without large price increases. Compliance with any new sweeping legislation is always difficult-and particularly so in today's adverse economic climate, which is being aggravated by the steady stream of environmental control and tax-reform programs. In effect, while government is unwittingly but surely undercutting the country's productive capabilities, it blames industry for the resulting failure to meet consumer demand. Any such real or alleged failure then brings heightened bitterness from Congress. During the recent energy shortage, for instance, threats of nationalization were ventilated in public along with proposals to abolish the mineral depletion allowance.

Jan 11, 1974

By Raymond O. Ladoo

FUSED quartz is a glass made by the fusion of nearly pure silica. Some confusion in terminology exists but in the trade today "fused quartz" generally refers to the perfectly transparent colorless product made from rock crystal whereas "fused silica" is a white, translucent product made from silica sand. Vitrified silica is the term preferred by purists for all quartz glass, but it lacks the definiteness of -the trade terms. Since the raw materials, methods of production, and properties of the finished products arc different for the two types, the trade terms are preferred. As fused quartz is amorphous, it-physical properties differ greatly from those of quartz crystal. Lacking crystallographic directions and having no piezo-electric properties, fused quartz. of course, has no value for the making of radio oscillator plates; but it does have other valuable and unique properties. Perhaps the 'best known and most useful properties are its extremely low coefficient of expansion and its ability to transmit short-wave ultraviolet radiant energy. Crystal quartz not only has an aver-

Jan 1, 1947

By J. H. Schloen, C. W. Clark

Two papers have been written previously concerning operations at the Montreal East plant of Canadian Copper Refiners Limited. The first one,' written in 1932, described silver-refinery operations at the time for producing silver and gold bullion from tankhouse anode slimes; the second,2 published in 1933, consisted of a description of the entire plant. Since publication of these papers the refinery has become the world's largest producer of refined selenium. The first selenium was produced in August 1934. Tellurium production on a commercial scale followed in October 1935. This paper will deal with selenium and tellurium production and also with present operations in the silver refinery. Blister cakes from Hudson Bay Mining and Smelting Co., Flin Flon, Manitoba, and commercial anodes from Noranda Mines Limited, Noranda, Quebec, are refined at Montreal East. Both these bullions have unusually high gold, selenium and tellurium content. The average assay of raw slimes produced from domestic and Noranda anodes is about 40 per cent Cu, 3600 oz. per ton Ag, 800 oz. per ton Au, 22 per cent Se and 3.7 per cent Te. Early Silver-refinery Operations From the start of operations in 1931 until July 1934, the raw slimes were oxidize-roasted at 700" I?. in a Nichols-Herreshoff furnace, acid-leached with tankhouse discarded foul electrolyte (20 per cent H²SO), filtered and charged directly to the doré furnace for refining to doré meta1. This is the customary method for treating tankhouse anode slimes but was not suitable at the Montreal East plant because of the high selenium and tellurium content of our slimes. In the acid-leaching process about 50 per cent of the selenium and tellurium in the roasted slimes was dissolved in the electrolyte. These elements were recovered with the copper as a sludge in a small electrolytic

Jan 1, 1943

By C. W. Clark, J. H. Schloen

Two papers have been written previously concerning operations at the Montreal East plant of Canadian Copper Refiners Limited. The first one,' written in 1932, described silver-refinery operations at the time for producing silver and gold bullion from tankhouse anode slimes; the second,2 published in 1933, consisted of a description of the entire plant. Since publication of these papers the refinery has become the world's largest producer of refined selenium. The first selenium was produced in August 1934. Tellurium production on a commercial scale followed in October 1935. This paper will deal with selenium and tellurium production and also with present operations in the silver refinery. Blister cakes from Hudson Bay Mining and Smelting Co., Flin Flon, Manitoba, and commercial anodes from Noranda Mines Limited, Noranda, Quebec, are refined at Montreal East. Both these bullions have unusually high gold, selenium and tellurium content. The average assay of raw slimes produced from domestic and Noranda anodes is about 40 per cent Cu, 3600 oz. per ton Ag, 800 oz. per ton Au, 22 per cent Se and 3.7 per cent Te. Early Silver-refinery Operations From the start of operations in 1931 until July 1934, the raw slimes were oxidize-roasted at 700" I?. in a Nichols-Herreshoff furnace, acid-leached with tankhouse discarded foul electrolyte (20 per cent H²SO), filtered and charged directly to the doré furnace for refining to doré meta1. This is the customary method for treating tankhouse anode slimes but was not suitable at the Montreal East plant because of the high selenium and tellurium content of our slimes. In the acid-leaching process about 50 per cent of the selenium and tellurium in the roasted slimes was dissolved in the electrolyte. These elements were recovered with the copper as a sludge in a small electrolytic

Jan 1, 1943

By D. V. Carter, Dan C. Williams, John R. Coombs

Exploration was active in East and East Central Texas during 1944. Ten oil fields were discovered during the year, of which four show promise of development. The discovery wells of the Sand Flat and Tyler, South fields were drilled to a depth greater than 10,000 ft., and the latter field now produces from the Pettit at a depth of 9890 ft. The Sand Flat well was plugged back to the Paluxy. The other two fields are Glen Rose producers near 8000 ft. The Pickton field produces from the Bacon Lime and Winnsboro from the Rodessa section. The Eylau field, Bowie County, was significant as the first Smackover production in Texas. Magnolia drilled a test in the Concord field, which topped salt. The most extensive and significant development in the district was the Carthage gas-condensate field. It expanded from the 8000 acres of last year to an estimated 190,000 acres, or about 300 sq. miles, and is not defined as yet. The first oil production in the Carthage area was made from the Travis Peak in 1944 in the Rogers Lacy's Cameron Lumber Company well No. I, on the northwestern side of the field. The New Hope field, Franklin County, scored the largest number of completions during 1944 with 24, bringing its total number of wells to 27. Two more pays were opened and produced as dual completions with the older horizons. The Manziel field, Wood County, had 19 new wells added during the year, for a total of 29, while the Pittsburgh field, Camp County, reached a total of 23 wells by completing 14 new ones. Material shortages and drilling restrictions dropped the total number of producing wells completed in the district from 171 during 1943 to 141 for 1944. Abandonments increased from 531 during 1943 to 609 for 1944. Of this number, 479 were in the East Texas field. Subsidy payments had very little effect in the district and it was mostly a few of the old fault-line fields that had any wells to fall within the requirements for subsidy payments. The prices of crude oil remained constant in the district except for increases as a result of subsidy payments. Production and Probation Wartime demands called for increased allowables for many fields, consequently the condensate and oil production for 1944 increased to 190,016,180, which is up 6.9 per cent over 1943. The East Texas field, of course, remained the principal producer of the district, accounting for 134,768'499 bbl. during the year, or 71 per cent of the district total production of condensate and oil. The field topped its own 1943 production by 4.8 per cent and became the first field in the world to produce 2 billion barrels of oil. The Hawkins field remained the second largest oil producer in the district, with 13,317,088 bbl. for the year, a drop of 6.8 per cent from 1943, while Van field was third with 11,635,708 bbl. The

Jan 1, 1945

By H. F. Yancey, M. R. Geer, C. L. Allyn, R. H. Eckhouse

W. M. Bertholf—This is an excellent report of a well-conducted investigation, of sufficient scope to provide generally useful information. Some years ago we had occasion to test the Humphreys spiral on the middling from our table plant. The conclusions reached in this investigation come as no surprise to us. In certain applications it is virtually impossible to improve on the spiral from the monetary returns point of view even though its "efficiency" may be low. We have noted that in all successful applications of the spiral the feed is "classified," hence we were somewhat disappointed in the showing the spiral made on the Poplar Ridge coal, the only one of the four which could really be considered the equivalent of a classified feed. As was noted in the paper, however, this coal contained a considerable amount of middle and high-gravity material, apparently more than enough to make up for the theoretical advantage of small particles in these categories. A comparison of particle size in the various specific gravity classes of the four coals is given in table XXV. Table XXV. Comparison of Particle Size in Various Specific Gravity Classes. (Unit size, 150 m to 0.105 mm) Black Eagle Clements Poplar Ridge Rosly,n 1.3 Float 7.47 10.60 8.68 9.66 1.3 x 1.4 7.89 7.96 7.58 8.20 1.4x1.6 7.24 8.36 5.58 6.85 1.6 x 1.8 7.98 8.31 3.42 7.33 Sink 1.8 7.85 7.13 5.09 7.41 Avg 7.69 10.08 7.15 8.38 This tabulation indicates that there was very little difference in the size of the various gravity fractions for three of the coals, Poplar Ridge varying the most. Examination of figs. 3, 6, 7, and 8 reveals a general similarity of behavior for all coals except Black Eagle. Would the authors care to speculate on the reasons for the difference in the distribution curve for the sink 1.60 material in the washed coal of fig. 3 as compared to the others? This difference is particularly noticeable in the 8xl4-mesh size. Was there a "shape effect"? J. D. Price and W. M. Bertholf—The performance data on three of the coals studied appear to be typical, but there are certain departures from the general pattern in the case of the Poplar Ridge coal which are large enough to deserve special consideration. For example: 1. Despite the high proportion of sink 1.60 material in the feed, it was not possible to make a corresponding proportion of high-ash reject. (See table XVI.) 2. Even though approximately 70 pct of the feed was 1.40 float with an ash content of 6.6 pct, and this

Jan 1, 1951

By R. H. Eckhouse, M. R. Geer, H. F. Yancey, C. L. Allyn

W. M. Bertholf—This is an excellent report of a well-conducted investigation, of sufficient scope to provide generally useful information. Some years ago we had occasion to test the Humphreys spiral on the middling from our table plant. The conclusions reached in this investigation come as no surprise to us. In certain applications it is virtually impossible to improve on the spiral from the monetary returns point of view even though its "efficiency" may be low. We have noted that in all successful applications of the spiral the feed is "classified," hence we were somewhat disappointed in the showing the spiral made on the Poplar Ridge coal, the only one of the four which could really be considered the equivalent of a classified feed. As was noted in the paper, however, this coal contained a considerable amount of middle and high-gravity material, apparently more than enough to make up for the theoretical advantage of small particles in these categories. A comparison of particle size in the various specific gravity classes of the four coals is given in table XXV. Table XXV. Comparison of Particle Size in Various Specific Gravity Classes. (Unit size, 150 m to 0.105 mm) Black Eagle Clements Poplar Ridge Rosly,n 1.3 Float 7.47 10.60 8.68 9.66 1.3 x 1.4 7.89 7.96 7.58 8.20 1.4x1.6 7.24 8.36 5.58 6.85 1.6 x 1.8 7.98 8.31 3.42 7.33 Sink 1.8 7.85 7.13 5.09 7.41 Avg 7.69 10.08 7.15 8.38 This tabulation indicates that there was very little difference in the size of the various gravity fractions for three of the coals, Poplar Ridge varying the most. Examination of figs. 3, 6, 7, and 8 reveals a general similarity of behavior for all coals except Black Eagle. Would the authors care to speculate on the reasons for the difference in the distribution curve for the sink 1.60 material in the washed coal of fig. 3 as compared to the others? This difference is particularly noticeable in the 8xl4-mesh size. Was there a "shape effect"? J. D. Price and W. M. Bertholf—The performance data on three of the coals studied appear to be typical, but there are certain departures from the general pattern in the case of the Poplar Ridge coal which are large enough to deserve special consideration. For example: 1. Despite the high proportion of sink 1.60 material in the feed, it was not possible to make a corresponding proportion of high-ash reject. (See table XVI.) 2. Even though approximately 70 pct of the feed was 1.40 float with an ash content of 6.6 pct, and this

Jan 1, 1951

By C. R. Sandberg, C. A. Connally, N. Stein

This paper describes the results of volumetric efficiency tests on oil well pumps handling gas oil mixtures. The work was performed in a large scale, above ground unit wherein test conditions could be accurately controlled and measured. The main variables studied were gas/oil ratio (including gas from solution and free gas mixed with oil), pump compression ratio, pump stroke length, pump speed, and clearance volume between the valves at their closest approach. Results are presented for two different pumps and for oils of two viscosities. Relatively small amounts of gas entering the pump resulted in large decreases in volumetric efficiency. Under conditions where the pump was operating at reduced efficiency because of the presence of gas, it was found that variation in the clearance volume between the standing and traveling valves had a considerable effect on pump efficiency level. This effect of the valve clearance volume was found to be significantly altered by the viscosity of the oil used in the tests. The effects on pump efficiency of the other variables studied were found to be relatively small over the range of conditions utilized. INTRODUCTION The production of oil by pumping is often hampered by low volumetric efficiency. A direct increase in lifting costs results from low volumetric efficiency. An indirect increase in lifting costs, probably greater than the direct increase, results from additional wear and tear on pumping equipment and from the down-time necessary for the repairs which can be traced to low-efficiency operation. Both increases in lifting costs tend to reduce economically recoverable oil. A number of different factors can contribute to low pump efficiency. A known basic cause of low efficiency is the presence of free gas in the pumped fluid. Pump volumetric efficiency is calculated only on the basis of liquid pumped and because any free gas pumped is discounted, this volume of free gas would represent a loss of pump efficiency. However, gas also causes a reduction in pump efficiency because it is a highly compressible fluid. It is known that pumps some- times "gas lock" because of excessive gas-to-liquid ratios in the pump barrel. Little is known of the role of gas compressibility in the intermediate case where the pump is operating at low efficiency. The opinion exists, however, that oil-well pumps tend to operate at higher efficiency with long stroke lengths at low speeds, but no quantitative studies of these pumping variables have been reported. It was believed that a much better understanding of the variables which control pump volumetric efficiency could be obtained and that possibly some suggestions as to the methods for increasing efficiency might be found from a study of the operation of pumps handling gas under closely controlled conditions. Previous investigators have studied the effects on pump efficiency of such factors as oil viscosity, oil temperature, slippage of oil. past pump plungers, pump submergence, valve size and spacing, pressure above pump plunger and fluid vapor pressure. However, none of these published investigations were conducted with pumps being subjected to large amounts of gas such as might be the case in a pumping well, nor did any of the investigations study the effect of variation in stroke length or pump speed. A large-scale teat unit was therefore constructed for studying the operation of pumps handling gas and for evaluating effects of such variables as pump stroke length and pump speed. PROCEDURE AND EQUIPMENT A schematic diagram of the pump testing equipment is given in Fig. 1. A 45-ft length of 6-in. casing is mounted vertically in a 65-ft tower. Sight ports are mounted in the casing at intervals near the location of the pump intake and the liquid level in the casing. These sight ports are fitted with Lucite windows sealed by neoprene "0" rings. The Lucite windows are machined to conform to the I.D. of the casing so that no obstruction to flow is present along the casing wall. The casing is fitted with a tubing head and 2-in. tubing is hung inside the casing. Pumps are seated in a shoe attached to the 2-in. tubing. A 1-in. polish rod is attacked directly to the pump without any intervening sucker rods. The top of the polish rod is attached to the weight carrier, which contains a number of weights to be used to force the polish rod in against tubing pressure on the down-stroke. This is necessary because a long string of sucker

Jan 1, 1953

By Oliver Bowles

WAR necessities have spurred inventive genius in many fields. A grinding mill without any moving grinding parts stirs the imagination. Among the new and striking accomplishments in the heterogeneous group of nonmetallic industrial minerals is the use of an electric arc to speed up manyfold the difficult and delicate task of drilling a microscopic hole in a diamond, the hardest of all known substances. Outstanding in the field of optical research is the ability that man has developed to improve upon nature by making in the laboratory optical crystals many times larger than those usually found in rocky crevices. These are merely samples of numerous events and circumstances of noteworthy import, many of which are recorded in this review. Termination of the second World War in 1945 permits an appraisal of the effects of the conflict and the probable effects of the coming restoration of a peacetime economy on the nonmetallic mineral industries. Some industries were stimulated greatly by the war, notably mica, quartz crystal, graphite, spinning asbestos, potash, fluorspar, barite, and refractories. The large-tonnage industries connected with the building trades, however, were forced to curtail their activities, except where their products were needed for wartime construction. Their reconversion to peacetime production will not be difficult.

Jan 1, 1946