Search Documents

By Jun-Yan Chen

Ground control problems in sublevel caving become evident as the rock pressure increases with depth. Recently, a finite element analysis of the stability problem of the sublevel caving method was completed by the author. This paper summarizes the results of stress analysis in sublevel extraction drifts under different field stress conditions by using linear elastic and nonlinear elastic-plastic finite element modeling techniques. A critical stress concentration will occur in the uppermost sublevel drifts beneath the caved area or blasted ore area. During the blasting and drawing cycle, a tensile and shear failure condition could develop in the center extraction drift when it would be mined last. Under a high horizontal stress field condition, almost all tensile stress in the back of the extraction drifts will be eliminated and only slight yield can be seen in the floor of the extraction drifts. Compared to the cases under the stress field where vertical stress is the dominant factor, the total yielding zone will be greatly reduced because of an in- creasing horizontal stress field with depth. However, it is predicted that the center of each ore column side will experience excessive shear stress that probably will result in ore failure. The two major conclusions drawn from this study to improve the overall stability of sublevel caving are: (1) the drift width must be carefully controlled and an appropriate stoping sequence selected; and (2) the sublevel caving method can be used in deep min

Jan 1, 1983

NEW MEMBERS The following list comprises the names of those persons who became members during the period Apr. 10 to May 10, 1915: Members ADMAN, WILLIAM, Supt., Susquehanna Coal Co Lykens, Pa. BARTH, CARL G., JR., Min. Engr 6151 Columbia Ave., Philadelphia, Pa. BOOTH, ERIC EDWIN, Min. Engr., Mount Elliott Mine, Selwyn via Cloncurry, North Queensland, Australia. BOYDELL, HARRY CYRIL, Asst. Mgr., Randfontein Central Gold Min. Co., Box 42, Randfontein, Transvaal, South Africa. BRADY, SAMUEL HOWARD, Mine Supt Bohemian Club, .San Francisco, Cal. Buses, HARRY EDWARD, Mine Supt., Engels Copper MiningCo Keddie, Cal.

Jan 6, 1915

By MALCOLM FRASER

I was delighted to be invited to be patron of this Joint Conference, but the challenging task you have set yourselves, and your speakers' depth of expertise, deny anyone, even the patron, the opportunity to be patronizing. Australia's history has been inextricably linked with the fortunes of our great mining industry. That link will remain. Just as the gold rushes of the last century, and the discoveries at Kalgoorlie and Broken Hill changed the lives of generations, so the more recent development activity in iron ore, bauxite, nickel, coal, and uranium are having a significant impact on the lives of Australians today. The minerals industry has contributed to Australia's jobs and prosperity. Mining is not free of problems, but so long as safeguards are strong and appropriate the net benefits the mining industry brings Australia will continue to be enormous. We rely on our mining industry to find, prove, develop and sell our minerals profitably, and my Government is committed to maintaining a healthy mining industry. In the past year there have been positive signs of a resurgence in exploration and development. The North-West Shelf ventures are spending $50 million on a feasibility study to work out the extent of future investment in that project; exploration expenditure for minerals other than petroleum increased by 34 per cent in 1976-77 to $134 million; petroleum exploration increased dramatically last year almost doubling to $94 million-this year it is projected to reach $125 million.

Jan 1, 1978

By A. W. Schlechten, R. F. Doelling

Parkes' process crusts were vacuum distilled using a shortened Pidgeon retort. Zinc was effectively removed below 800°C and recovered as a zinc sheet easily stripped from the furnace liner. Lead dasdistillationazinc required about 950°C and the resulting lead condensate tillationtended to stick to the thin metal liner. Final purity of residue is limited only by nonvolatile metals such as copper. THE successful commercial application of vacuum distillation for the removal of zinc from lead, as described by W. T. Isbell,' raises the question of whether or not a similar method can be used for other metal separations. Preliminary laboratory experiments on the vacuum distillation of Parkes' crusts by one of the authors' gave such encouraging results that it was decided to make a series of tests with large scale equipment to determine the results that might be expected in plant operation. The pilot-plant test results are reported in this paper. The great advantages of vacuum dezincing are its simplicity, the relatively low temperature of operation, and the fact that the zinc is recovered in the metallic state ready for use again in the desilveriza-tion of lead bullion. These same advantages and others would be realized from the vacuum distillation of the zinc-lead-silver crusts made in the Parkes' process. Zinc readily will distill over at temperatures of 800" to 900 °C as contrasted with the 1200°C or more used in the Faber du Faur furnace. Furthermore, the recovery of zinc as metal is practically perfect since there is no loss by oxidation or fuming. If the vacuum distillation is continued and hastened by raising the temperature to around 1000°C, the lead will distill over at an appreciable rate and deposit in a warmer zone of the condenser. This lead will contain a small amount of silver, but it can be returned to the desilverizing kettles and there is not the chance of loss that there is in disposing of the rich litharge from cupelling. The lower temperatures required will mean a saving of fuel and less wear on the equipment. One further point is that the vacuum distillation could be run on a small scale practically continuously, so as to avoid the accumulation of large amounts of silver-rich material and the need of assembling a large crew for special cupellation runs. It should be pointed out here that the final purity of the silver residue will depend on the copper or iron content of the crusts, as these and other metals with low vapor pressure will not be eliminated. The idea of treating the silver-zinc-lead crusts from the desilverization of lead bullion by vacuum distillation is not a new one, but such experiments have not been reported, as far as can be determined. In 1912, T. Turner presented a paper3 before the Institute of Metals on the vacuum distillation of brass, and a member of the audience suggested that he try his method on Parkes' crusts. In 1935, W. J. Kroll, noted for his discovery of debismuthiz-ing lead by calcium additions, published a paper' on vacuum distillation of metals and pointed out possible applications in the lead industry. Principles of Separation The successful separation of two or more metals by distillation depends upon an appreciable difference in the effective vapor pressures of the metals in the alloy to be treated. The vapor pressures of the common metals have been determined with considerable accuracy; for example, at 800°C the vapor pressures of the individual metals which are of particular interest in this paper are about .as follows: Zn, 241 mm; Pb, 0.0553 mm; and Ag, 0.0000276 mm. Unfortunately,, data are not available on the activities of the components in the ternary system Zn-Pb-Ag, but it can be estimated that on the basis of the vapor pressures of the individual metals a good separation can be made by distillation. The preliminary laboratory tests previously mentioned' supported this assumption. The pilot-plant size vacuum distilling furnace is shown in Fig. 1. It consisted of an abbreviated Pidgeon retort, 5 ft long with an ID of 8 in., heated by six silicon carbide elements placed symmetrically

Jan 1, 1952

By J. L. Huiatt, M. C. Fuerstenau, M. C. Kuhn

Dithiophosphatogen is the species responsible for flotation of pyrite when dithiophosphate is added as collector. Oxidation of collector apparently occurs by reaction with oxygen adsorbed on the pyrite surface. Oxidation of dithiophosphate and xanthate is also effected with Cu++, Cu(OH) , and Fe+++ and rates of oxidation are presented as a function of pH. Reasons for the selectivity observed when dithiophosphate is added as collector in a natural ore system as compared to xanthate are presented and discussed.

Jan 1, 1972

By E. S. Greiner

STUDY of the plasticity of germanium or other semiconductor crystals affords unusual opportunities to extend our knowledge of deformation mechanisms. Crystals are available having extraordinary perfection and very high purity. They deform by slip on the systems {111} <110>,1-3 as do crystals of the simple face-centered-cubic structure. Dislocations generated in them during slip are easily revealed in the form of etch pits on either (111) or (100) surfaces.4,5 This fact alone makes possible more detailed studies of mechanisms than is usually the case with metals but, even further, the effect of deformation on their electrical conductivity is very large compared with metals. This comes about not only because the mobility of the charge carriers is reduced, as in deformed metals, but also because the number of these carriers is greatly altered. This latter effect seems closely related to the formation of both line and point imperfections during deformation and thus provides a needed tool for the study of the kinds and distributions of these imperfections. Other investigators have deformed germanium at elevated temperatures by bending,1, 6-8 compres-sion,6, 0,10 tension,2,3,6,11,12 torsion,23 and indentation." Wang and Alexander" have also reported successful indentation at room temperature. Dislocation etch pits consequent to deformation have been observed and studied.7,8,10,18,14,20 The experiments to be de- scribed here include principally the compression and the subsequent annealing of germanium with concomitant studies of etch pits, microstructures, and electrical properties. Both single crystals and heavily twinned specimens were used. Some indentation studies are included. Experimental Methods Plastic compression was effected in the apparatus shown schematically in Fig. 1. It consists of two tantalum platens contained in a helium atmosphere and so arranged that pressure can be applied by a hydraulic press. The specimen between the platens is heated by the surrounding furnace. The specimen is usually a small crystal cube about 0.30 in. on an edge. A control specimen is always inserted so, that it is subject to the same thermal cycle as the one being deformed. This serves to detect any impurity contamination that might accompany the thermal treatment. For high temperature work, where such impurity contamination often occurs, the specimens were first plated with gold whenever subsequent electrical properties were to be determined. This method" is effective in preventing significant contamination of germanium up to temperatures at least as high as 750°C, as evidenced by the constancy of the electrical conductivities of control specimens subjected to the same heat treatments. The total range of temperature used for deformation was from 375°C, the lowest at which significant flow was observed, up to 900°C. Microscopic examination was made after mechanical and chemical polishing and etching. Dislocation pits were revealed with CP-4 etchant by the tech-

Jan 1, 1958

By J. C. Reed, P. J. Shenon

The Elk City district is in north-central Idaho about 60 miles east of Grangeville and near the headwaters of the South Fork of the Clearwater River (Fig. 1). At the height of its boom in the early sixties, Elk City had a population of more than 2000 people, Published estimates of the placer production from the district range from $10,000,000 to $18,500,000. Although the first quartz-vein location was made as early as 1870, very little gold was extracted from quartz ores until after the completion of the American Eagle mill in 1902. Between 1902 and 1932 a total of from $750,000 to $1,000,000 was taken from about six properties. General Geology Distribution of Rocks Banded gneiss (Fig. 2) is the most aburldant bedrock in the Elk City district. It is interbedded with schist and quartzite and ill some places these rocks have been intruded by sills and dikes. Banded gneiss prevails in the western part of the area whereas schist prevails to the southeast. Augen gneiss occurs for the most part as irregular bodies, which lie transverse to the trend of the banded gneiss and schist. It is largely confined to two areas; one of which extends from east of the American Eagle mine westward as far as the Black Pine mine, a total distance of about five miles, and another area of about two square miles in the vicinity of the California-Idaho placer mine. Quartzite is fairly abundant. In addition to the bands of the latter interbedded with gneiss and schist, some large lenses crop out in the southeastern part of the dik-trict near the southern contact of the area underlain by granodiorite. Granodiorite crops out over a large area and extends northeastward

Jan 1, 1935

By P. J. Shenon, J. C. Reed

The Elk City district is in north-central Idaho about 60 miles east of Grangeville and near the headwaters of the South Fork of the Clearwater River (Fig. 1). At the height of its boom in the early sixties, Elk City had a population of more than 2000 people, Published estimates of the placer production from the district range from $10,000,000 to $18,500,000. Although the first quartz-vein location was made as early as 1870, very little gold was extracted from quartz ores until after the completion of the American Eagle mill in 1902. Between 1902 and 1932 a total of from $750,000 to $1,000,000 was taken from about six properties. General Geology Distribution of Rocks Banded gneiss (Fig. 2) is the most aburldant bedrock in the Elk City district. It is interbedded with schist and quartzite and ill some places these rocks have been intruded by sills and dikes. Banded gneiss prevails in the western part of the area whereas schist prevails to the southeast. Augen gneiss occurs for the most part as irregular bodies, which lie transverse to the trend of the banded gneiss and schist. It is largely confined to two areas; one of which extends from east of the American Eagle mine westward as far as the Black Pine mine, a total distance of about five miles, and another area of about two square miles in the vicinity of the California-Idaho placer mine. Quartzite is fairly abundant. In addition to the bands of the latter interbedded with gneiss and schist, some large lenses crop out in the southeastern part of the dik-trict near the southern contact of the area underlain by granodiorite. Granodiorite crops out over a large area and extends northeastward

Jan 1, 1935

The Elk City district is in north-central Idaho about 60 miles east of Grangeville and near the headwaters of the South Fork of the Clearwater River (Fig. 1). At the height of its boom in the early sixties, Elk City had a population of more than 2000 people, Published estimates of the placer production from the district range from $10,000,000 to $18,500,000. Although the first quartz-vein location was made as early as 1870, very little gold was extracted from quartz ores until after the completion of the American Eagle mill in 1902. Between 1902 and 1932 a total of from $750,000 to $1,000,000 was taken from about six properties. General Geology Distribution of Rocks Banded gneiss (Fig. 2) is the most aburldant bedrock in the Elk City district. It is interbedded with schist and quartzite and ill some places these rocks have been intruded by sills and dikes. Banded gneiss prevails in the western part of the area whereas schist prevails to the southeast. Augen gneiss occurs for the most part as irregular bodies, which lie transverse to the trend of the banded gneiss and schist. It is largely confined to two areas; one of which extends from east of the American Eagle mine westward as far as the Black Pine mine, a total distance of about five miles, and another area of about two square miles in the vicinity of the California-Idaho placer mine. Quartzite is fairly abundant. In addition to the bands of the latter interbedded with gneiss and schist, some large lenses crop out in the southeastern part of the dik-trict near the southern contact of the area underlain by granodiorite. Granodiorite crops out over a large area and extends northeastward

Jan 1, 1935

By P. J. Shenon, J. C. Reed

The Elk City district is in north-central Idaho about 60 miles east of Grangeville and near the headwaters of the South Fork of the Clearwater River (Fig. 1). At the height of its boom in the early sixties, Elk City had a population of more than 2000 people, Published estimates of the placer production from the district range from $10,000,000 to $18,500,000. Although the first quartz-vein location was made as early as 1870, very little gold was extracted from quartz ores until after the completion of the American Eagle mill in 1902. Between 1902 and 1932 a total of from $750,000 to $1,000,000 was taken from about six properties. General Geology Distribution of Rocks Banded gneiss (Fig. 2) is the most aburldant bedrock in the Elk City district. It is interbedded with schist and quartzite and ill some places these rocks have been intruded by sills and dikes. Banded gneiss prevails in the western part of the area whereas schist prevails to the southeast. Augen gneiss occurs for the most part as irregular bodies, which lie transverse to the trend of the banded gneiss and schist. It is largely confined to two areas; one of which extends from east of the American Eagle mine westward as far as the Black Pine mine, a total distance of about five miles, and another area of about two square miles in the vicinity of the California-Idaho placer mine. Quartzite is fairly abundant. In addition to the bands of the latter interbedded with gneiss and schist, some large lenses crop out in the southeastern part of the dik-trict near the southern contact of the area underlain by granodiorite. Granodiorite crops out over a large area and extends northeastward

Jan 1, 1935

By W. D. Haselton, J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte.5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

By B. M. Larsen

A discussion based on three commercial furnace tests and electrical analogue calculations is presented. It shows that while regenerator efficiency is mainly dependent on loading or relative amount of heat exchange surface plus the heat transfer coefficients as effected by flow velocity, the actual air preheat temperature can be high or low, largely independent of regenerator efficiency, mainly due to the diluting or unbalancing effects of cold air leakage into various parts of the furnace system. THERE are many signs of a renewal of interest in the heat regeneration aspect of the open hearth process, among them being the recent paper by Marsh,&apos; the introduction of auxiliary checkers in the stacks of the Isley furnace design, and a number of recent installations of two-pass checkers in new and old furnaces. However, there are also signs of yielding to the usual temptation of oversimplifying a problem. Faced with the job of obtaining better draft on a furnace, for example, a good designer always recognizes that focusing attention on some one factor, such as height of the stack or capacity of the exhaust fan, does not make his problem any easier; rather he must look at the whole system, including such items as valve resistances, bends in the flues, and flow resistance in the waste heat boiler; then he must make his design in relation to the available draft so as to avoid any serious bottleneck in the system. Yet this example is really much simpler than the problem of air preheating, and again, the latter problem is not really made easier by concentrating on air temperature in uptakes and on the more obvious methods for making this air as hot as possible. Also to be considered are such things as the total amount of air needed theoretically for complete combustion at any selected fuel rate, together with that needed for oxygen absorbed into the bath and for burning the combustible gases given out from the bath, plus some excess air. Furthermore, how does this total air requirement relate to the regenerator efficiency at various loadings? How much of the total air equivalent in stack gases will come from preheated air passed through the whole length of the incoming regenerator and how much from air leakage into various zones of the whole furnace system? Does the effect of leakage air differ depending on whether it leaks into the ingoing regenerator, the furnace above floor level, the outgoing regenerator, or the stack zone? Over a number of years we have in this Laboratory experimented with methods for measuring hot gas temperatures; we have measured, approximately, the efficiency of a few regenerators on commercial furnaces and we have developed an electrical analogue&apos; for calculations of regenerator efficiency. The whole problem is too complex to cover in one paper even with a more complete background of data than we possess, but we can attempt here to clarify certain aspects in a general way, hoping to assist specific plant studies on individual furnaces. Some of our earlier experience has been incorporated into chaps. 4, 19, 20, and 21 in the book "Basic Open Hearth Steelmaking,"" and on the assumption that this text is available to most readers, this discussion has been shortened by references to that book. The most recent design of a flowing-gas thermocouple which we are now using for measurement

Jan 1, 1955

By J. Burns Read, Charles H. Fulton

A previous article1 by the authors contained a general description of the new roasting furnace herein described but it did not go into detail as to the metallurgical behavior or the results obtained. Believing that such information would be of great value, they have elaborated on the subject and have given many unpublished details. The furnace described applies the principle of roasting finely divided zinc-sulfide ores, now produced in large quantity by the flotation process, in gaseous suspension; that is, the ore particles are carried, in suspension, in a current of air and gaseous products of the roast. The relatively great fineness of flotation concentrate presents difficulties and problems of roasting in furnaces of the ordinary type; the fine ore is forwarded through the furnace in the form of a shallow bed and its very fineness leads to dense impervious bedding which prevents oxygen from reaching the interior of the bed, thus unduly lengthening the time of roasting and preventing the elimination of the last of the sulfur. The fineness of the concentrate, normally, should lead to a rapid and complete roast, for the speed of roasting is a function of the surface exposed to oxygen, which surface is greatest, per unit of weight, in very fine material. The difficulty in bed roasting is to get the oxygen to the particle. If the fine ore, during the roasting, could be freely suspended in oxidizing gases, full advantage could be taken of the great surface conferred by its fineness. This fundamental idea, of course, is not new, for the Stedtefelt furnace, familiar to the older metallurgists, is an example of it; but the manner in which this is accomplished may be new. The numerous efforts to roast in gaseous suspension show that the idea is attractive; in fact, an analysis would indicate that it is the most reason-

Jan 1, 1925

By Sadao Maruyama

INTRODUCTION Since the big discovery of Kuroko deposits in Kosaka mine, Akita Pref., northeastern Japan in 1959, major Japanese mining companies have been engaged in extensive exploration for the deposits expending large amounts of money. Above all their exploration activities have been particularly fruitful in discovering new deposits in northern Akita Pref. It is estimated that the total ore reserves newly found in the area are at least 50 million tons. Kuroko deposits are the most important ore source of copper, lead and zinc in Japan and have been mined since last century in the said area. Kuroko (black ore) is fine, compact aggregates with sphalerite , glena and barite as principal constituents and chalco- pyrite, pyrite and tetrahedrite as subsequent constituents. The name Kuroko comes from its appearance. It is not rare that total grade of copper, lead and zinc reaches 20 - 30% and the gold and silver content is also fairly good. Accordingly the unit value of the ore is much higher than the ore from other types of deposits. Besides the Kuroko ore, the Kuroko deposits consists of Ohko (yellow ore, massive cupriferous pyritic ore), Keikoh (silicious ore, cupriferous network ore) and gypsum ore. This type of deposit is considered to be not only an important source of base metal but also a source of gypsum and barite. Although the importance of this type of deposit had been commonly recognized, sub-surface nature of the occurrence hampered exploration work. In recent years the improved exploration techniques and increased knowledge of the Kuroko deposits have met with remarkable success in the location of new deposits. This outburst of exploration and dis-

Jan 1, 1970

By A. J. Lanza

THE prevention of illness among the employees of the mining industry is especially important in view of the importance of the industry, the unsettled conditions of labor, which emphasize the economic necessity for conservation of labor, and for humanitarian reasons. The burden of chronic illness is altogether unwarranted and unnecessary. If the industry is to maintain its labor supply in an efficient manner and keep the standard high, it is essential that it make every effort to keep its labor in good physical condition. The basic principles underlying health conservation are the same for any industry, but they are here applied especially to the mining industry, and more particularly, perhaps, to metal mining, as it is with this phase of the industry that the writer is most familiar, and as it is conceded that metal mining presents more health hazards than coal mining. The first step in the prevention of illness lies in securing employees who are in sound health and free from organic disease. I do not mean that all men who go underground should be physically perfect, but they should be free from organic defects of the heart, lungs, and other organs, or from anatomical defects that would- markedly increase their liability to accident. The number of men working underground in mines in this country whose physical, condition totally unfits them for such work presents-a situation that should not be allowed to continue, and which I believe is &apos;not equalled in any other, industry in the country. There is but one way to secure men who come up to the required standard, . and that is by a thorough physical examination before employment. I am fully aware of the objections felt toward such a procedure by many employers and employees. There is much to he said on both sides, but to any one who is at all familiar with the mining industry as it is today in this country, and who approaches the matter with an unbiased mind, there can be absolutely no doubt as to the necessity for physical examination. As a purely logical proposition this is self-evident, but there remains the further necessity of placing physical examinations on such a

Jan 2, 1919

By Richard H. Sprute, Dennis J. Kelsh

Slow-settling, fine-grained suspensions can often be dewatered and densified by applying direct current between buried electrodes. Although water removal rates and power expenditures depend on physical and chemical properties of the treated slurries, metal mine tailings from Idaho, Colorado, and Mexico have responded well in laboratory testing, as have 29 samples of ultrafine coal waste from mines in nine states. This Bureau of Mines report reviews field tests at two Idaho metal mines and describes the recent installation at the Henderson molybdenum mine near Empire, Colorado, and the treatment of coal sludge at a Clinchfield Coal Co. preparation plant near Dante, Virginia.

Jan 1, 1980

By Hsun Hu, R. S. Cline

A detailed studj) of texture formation in 2 pet Al-Fe single crystals with initial orientations of approximately (111) [112], (112) [111], and (112) [111] was made by examining the textures developed on the surface and at various interior sections of the crystal after rolling to various amounts. Depending&apos; upon the initial orientation of the crystal, the surface and interior textures may differ only in sharpness, or may differ essentially in orientation. The orientation of the (111) [112] crystal does not change upon rolling up to 70 pet, but after rolling more than 90 pet a distinct component of (001) (110] orientation is developed. The texture formed in the two (112) (1111 type crystals consists of (111) (1121 and (001) (1101 components. The latter, however, is largely confined to the surface layers. The textures formed on both sides of the crystal are identical, and the texture composition profile is approximately symmetrical with respect to the central section of the strip thickness. The formation of these texture components is analyzed. DURING the past seven or eight years, deformation and recrystallization textures in rolled Si-Fe single crystals have been extensively studied by various investigators.1-7 From these studies, much knowledge on texture formation in bee crystals of various initial orientations was obtained. However, these results also raised many questions, regarding particularly the correlation between deformation and recrystallization textures, as well as the deformation texture itself of some particular crystals. To take a (111) [112] type crystal as an example, it was shown by Dunn and Koh2, 3 that this orientation does not change during deformation by rolling. This finding is consistent with the conclusion reached by Barrett and Leven-son8 with respect to iron crystals that (111) [112] is one of the stable end orientations. However, different recrystallization textures were observed by Dunn and Koh3 in (111) [112] type crystals of different initial thickness, which widened differently during rolling even though their deformation textures were identical. Another interesting example, also from the results of Dunn and Koh2&apos;3 is that of texture formation in a (112) [111] crystal. This crystal developed a two-component deformation texture of (111) [112] plus (001) [110]. Its recrystallization texture, however, was found to be predominantly (110) [001], which is related to the (111) [112] component by a simple [110] rotation. This crystal, therefore, behaved as if the other deformation texture component, (001) [110], were not present. There are also discrepancies among the results of different investigators, as well as numerous unexplained fine features of the deformation texture of crystals of various initial orientations. In order to have a better understanding of all of these points, a detailed study of deformation textures is greatly needed. One of the obvious things that has been completely overlooked in previous texture studies is the possible effect of surface texture. All past work on the texture of Si-Fe single crystals was conducted in a rather simple manner, i.e., the rolled crystals were etched to a very thin sheet; then their textures were examined by transmission X-ray techniques. For recrystallization texture studies, unless precautions are taken by etching off a sufficient amount of the surface layer before annealing, the texture developed in the interior may be affected by the surface layer, which may well have a different initial texture and which may have undergone recrystallization earlier than the interior of the specimen. Because of this effect, it is now planned to reexamine the texture of various rolled and annealed single crystals at the surface, and at various sections below the surface by using reflection techniques. In some cases, both surfaces of the rolled crystal will be examined. In one of Dunn&apos;s early papers,9 he noted that at an early stage of rolling the crystal seems to divide roughly through the middle to become a sample which in effect consists of two layers having some what different orientations. This effect has never been further explored. The investigation described in the present paper constitutes the beginning of a series of thorough investigations of texture formation in deformed bee single crystals designed to clear up some of the uncertainties which have been discussed. We have chosen a high-purity 2 pet Al-Fe alloy for this investigation. It is known that the allotropic transformation of iron is eliminated by alloying with approximately 1petAl. Such an alloy, being very similar to silicon ferrite, can be heated to the solidus temperature without phase transformation. One reason for choosing A1-Fe instead of Si-Fe for the present investigation is that we have been able to make single crystals of a vacuum-melted high-purity A1-Fe alloy by the strain-anneal method without much difficulty, but were not successful in doing so with a vacuum-melted high-purity Si-Fe alloy. For many research purposes,

Jan 1, 1962

By Thomas Varley

IN THE congressional act establishing the Bureau of Mines one of the functions outlined was "to assist I the industry in the prevention of mineral waste." This had not only to do with the waste in mining but in milling and metallurgical practices, including smelting. The organization of the Bureau of &apos;Mines includes many divisions, each working in a particular field and charged with certain investigative work. The metallurgical division has the above duties under its immediate supervision, and the station located at Salt Lake City is directed by the chief of this division: There are ten experiment stations of the Bureau of Mines, located in various parts of the country, most of them being housed at state universities under cooperative agreements. Considerable care was exercised in locating the stations and in choosing the particular type of work to be investigated at each place. Inasmuch as the Bureau was designed to serve and cooperate with the industry it is only natural that the investigative work be of interest and importance to the territory immediately adjacent to the respective stations.

Jan 1, 1925

By A. E. Moss, J. K. Gustafson

MEASURED in terms of ore tonnage, the New Quebec and Labrador iron ore fields promise to rank with the greatest iron ore districts of the world. Over 400 million tons of high-grade ore for direct shipping have been discovered to date. Much greater amounts of lower-grade beneficiating ores are indicated by outcrops. Many hundreds of square miles of iron formation await testing. By 1954 iron ore will begin to move towards American blast furnaces, and shortly thereafter the annual rate of production is expected to reach 10 . million tons. To bring this vast project into being over $200,000,000 will have been spent for exploration and development, mining equipment, hydro plants, townsites, the building and the equipping of . a 360-mile railroad, and the construction of docks and ore-handling facilities. The most important iron ore deposits are located over 300 miles from tide water, see frontispiece and also Fig. 1. The frontispiece shows principal sources of iron ores and manganiferous iron ores for the U. S. and Canadian steel industry, and the major smelting districts are shaded on the map. No navi- gable rivers lead into the interior. When work was . commenced on this project there were no roads, no railroads, no communication ,system, no inhabitants, and no adequate maps either topographical or geological. The geological field season was limited to approximately 100 days per season. The obstacles facing this enterprise were many and varied. Its success will be due to the integrated team work of people of diverse skills. Explorers, Indian guides, prospectors, geologists, surveyors, mechanical, civil, electrical, and mining engineers,

Jan 1, 1954

By J. Q. Ehrgott

INTRODUCTION The U. S. Army Engineer Waterways Experiment Station (WES), under sponsorship of the Defense Atomic Support Agency, has recently developed a unique dynamic high-pressure triaxial testing device (DHT). The device permits acquisition of both axial and lateral deformation data while undisturbed soil and/or rock specimens are subjected to various states of controlled impulsive-type stresses produced by varying both the axial stress and the radial stress rapidly with time. The device is used to develop controlled dynamic pressure pulses within the triaxial chamber fluid on soil or rock test specimens to 3 inches in diameter. Controlled dynamic axial pulse loads are delivered to the specimen by a piston driven by an existing pneumatic ram loader (SECO). The DHT consists of a triaxial cell and a pressure supply and decay system which permits the chamber pressure to be varied with time. Together the DHT and SECO operate in a testing program so as to provide time varying confining pressures and axial loads to test specimens at independently controlled but synchronized programmed rise, hold, and decay times. Rise time is defined as the time from zero load or pressure to peak load or pressure; hold time is the time of constant peak load or pressure; and the decay time is the time from peak load or pressure to zero load or pressure. The maximum dynamic confining pressure attainable is approximately 15,000 psi and the fastest rise and decay times are 3 millisecond (msec) and 20 msec, respectively. This paper presents a description of the DHT, the necessary support equipment, and details of the measurement system. Performance evaluation tests conducted on clay siltstone and a Cretaceous sandstone are presented since the results demonstrate some of the capabilities of the device and show some of its characteristics.

Jan 1, 1971