Search Documents

By R. E. Pray, M. C. Fuerstenau, J. D. Miller, B. F. Perinne

Quartz cannot be floated with potassium amyl xanthate as collector at any pH. Complete flotation is achieved with certain minimal additions of amyl xanthate and Pb from pH 5.8 to 8.5 and with amyl xanthate and Zn from pH 7.5 to 8.1. The active species of these metal ions responsible for activation are shown to be PbOH and ZnOH No flotation was effected when Cu and Mg were added as activators. Previous work1,2,3,4,5,6,7 has shown that quartz may be floated in the presence of sulfonate or soap when the following two criteria are met: 1) some portion of the added metal ion has hydro-lyzed to its first hydroxy complex, and 2) a precipitate of the metal-collector has formed. Since sulfonate and soap, two substantially different anionic collectors, conform to these criteria, this phenomenon may well be expected to be of a general nature. In this view then, it would appear that any anionic collector, including xanthates, should also float quartz when these two criteria are met. The object of this paper is to demonstrate the conditions under which quartz will respond to flotation in the presence of potassium amyl xanthate. EXPERIMENTAL MATERIALS AND TECHNIQUES Quartz was prepared by leaching the sized sample (48 x 150 mesh) with HC1 until no iron could be detected in the leach liquor. Conductivity water, made by passing distilled water through an ion exchange column, was used in the investigation. Potassium amyl xanthate was selected as collector. Purification of this reagent was effected with the following method: 1) a laboratory sample of potassium amyl xanthate was dissolved to saturation in hot ethyl alcohol and filtered several times while still hot, 2) the filtrate was cooled, during which time potassium amyl xanthate crystallized out of solution; the xanthate was then separated from the solution by filtration, 3) the amyl xanthate was dissolved in fresh hot ethyl alcohol and filtered, 4) step (2) was repeated, 5) the crystalline potassium amyl xanthate was washed with ethyl ether five times, and 6) the xanthate was dried for 24 hours under continuous vacuum. Inorganic impurities are insoluble in hot ethyl alcohol whereas dixanthogen is soluble in ethyl ether. Five-gram charges of 48x150 mesh quartz were conditioned for 3 min in 125 cc of solution containing the reagents and were floated with the small-scale cell and procedure described in previous papers.478 Reagent grade HCl and NaOH were used for pH adjustment, while reagent n-amyl alcohol was added as frother. Frother addition is necessary with this technique, but it should be mentioned that data, similar to those shown in Fig. 2 for 1 x10-4 mole per liter Pb++ and 1 X 10-4 mole per liter AX-, were also obtained with a Hallimond cell in the absence of frother. EXPERIMENTAL RESULTS Clean quartz could not be floated with amyl xanthate at any pH. Flotation was achieved under certain conditions, however, when various metal ions were added to the system. The activating ions used were lead, zinc, copper and magnesium, added as reagent grade chloride salts. Lead as Activator: The effect of Pb++ as activator was examined at five different additions of amyl xanthate (Fig. 1, 2 and 3). When 1x 10-5 mole per liter xanthate was added in the presence of 1 x 10"4 mole per liter Pb ++, no flotation was obtained at pH 6.5 or below, while a recovery of about 60% was effected at pH 7. When the pH was increased to 7.8, no flotation was again obtained, Complete depression was noted from pH 7.8 to about 10, at which point a recovery of about 30% was achieved. At about pH 11, the precipitate of lead amyl xanthate which was present below this pH dissolved and complete depression occurred. When 2.5x 10-5 mole per liter xanthate was added with the same lead addition, no flotation was obtained at pH 5.8 and below, whereas a recovery of

Jan 1, 1965

By R. W. Raymond

THE absence of a convenient glossary of terms connected with mining and metallurgy has long been felt by the general public. It is to meet this want, not to furnish a technical manual for experts, that the following glossary has been prepared. It originated in an attempt on my part to revise for publication the manuscript of a compilation prepared from the appendix of Yale's work on Mining Titles and one or two other sources, to serve as an appendix to a new work on mining law, about to be published by Mr. H. N. Copp, of Washington, D. C. This revision soon assumed, contrary to my original intention, the proportions of a reconstruction; and with the consent of Mr. Copp, and for the purpose of receiving from my fellow-members valuable aid, I presented my still incomplete work as a paper at the Lake Superior meeting of the Institute, inviting from any quarter suggestions of new terms or better definitions to be incorporated in the glossary before its final publication. This invitation was so widely and generously responded to, that I cannot undertake to make in this place individual acknowledgments to those members of the Institute, and professional colleagues outside of it, who have favored me with assistance and advice. The labor bestowed upon this paper since its presentation at the Lake Superior meeting has considerably exceeded that of its first preparation, as may be inferred from its great increase in length, as well as the numerous alterations which it has undergone. It could certainly be still further enlarged and improved; but I think a comparison of it with any of the glossaries of the same class now in print will show, at least, that it is an advance upon what has hitherto been accomplished. 1 shall be grateful, however, for further criticisms and suggestions; and I purpose at some future time to incorporate in a supplementary paper the results of such additional collections or corrections as I may obtain. To avoid too great prolixity, I adopted at the outset the following general principles: 1. To include the most important technical words and phrases used by American miners and metallurgists, or occurring in English books and periodicals.

Jan 1, 1881

[Executive HENRY A. BUEHLER, Chairman ERLE V. DAVELER EDGAR RICHARD JOHN M. LOVEJOY WILLIAM WRAITH J. V. W. REYNDERS, Consultant Finance HENRY KRUMB, Chairman E. E. ELLIS PAUL D. MERICA H. G. MOULTON, Consultant]

Jan 1, 1936

By Charles Jackson Abrams

MINING is one of the major industries of the Rocky Mountain region and since the United States became involved in the present World War, all mines have been called upon by the Government for the maximum production of the strategic metals necessary. Operating under the most adverse conditions, such as priority requirements, slow delivery of necessary material and equipment, labor shortages, and freezing of all wages, which still permitted some industries to pay higher rates than were allowable in the mines, thereby drawing labor from the mines; and the United States Employment Service continually giving mine labor certificates of availability; these and many other problems made mine operation particularly difficult. Yet, in spite of these obstacles, the mining industry, either through its own resources or through Government subsidies in the form of loans or premium prices for strategic metal, have and still are making an all-out effort to meet Government demands. They, without question, have played a major role in assisting the war effort.

Jan 1, 1945

[ZAY JEFFRRIES, Vice-chairman PAUL D, MERICA, Chairman W, M, CORSE, Secretary Executive Committee J. It, FREEMAN, JR., Local Section S. SKOWRONSKI, Papers Committee R. S, ARCHER, Non-ferrous Data Sheets H, C, JENNISON, Membership Committee E, C, BAIN, Journal Committee L, W. SPRING Local Section Committee J. R, FREEMAN, JR,, Chairman R. J, ANDERSON, Cincinnati R. L. DOWDELL, Minneapolis R. S. WILLIAMS, Boston G, H, CLAMER, Philadelphia W. A. SCHEUCH, Chicago R, F, WOOD, New York]

Jan 1, 1928

[University of Alaska College, Alaska Mining Society MAURICE BUTLER, President EARL FOSSE, Secretary RAYMOND J. BARBER, Faculty Sponsor R. H. OGBURN, Counselor University of California Berkeley, California Mining Association THEODORE OLSEN, President ARTHUR K BOURRET, Secretary FRANK H. PROBERT, Faculty Sponsor GRANVILLE S. BORDEN, Counselor D. C. JACKLING, Associate Counselor Carnegie Institute of Technology Pittsburgh, Pennsylvania The Metals Society EDWARD J. BOYLE, President W. T. LANKFORD, JR., Secretary M. GENSAMER, Faculty Sponsor EDGAR C. BAIN, Counselor]

Jan 1, 1940

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 ROBERY W HUNT 1883 JAMES C, BAYLES 1884-1885 ROBERT H RICHARDS 1886 THOMAS EGLESTON 1887 WILLIAM B POTTER 1888 RICHARD PEARCE 1889 ADAM S HEWITT 1890 JOHN BIRKINBINE 1891-1892 H M HOWE 1893 JOHN FRITZ 1894 J D WEEKS 1895 E G SPILSBURY 1896

Jan 1, 1923

By AIME AIME

COMMITTEES. LOCAL COMMITTEE.-R. C. Crawford, Chairman; Harrison W. Craver, Secretary; Julian Kennedy, Taylor Allderdice, E. W. Pargny, Charles L. Miller, W. H. Rea, S. A. Taylor, M. E. Wadsworth, W. A1. Henderon, A. C. Dinkey, W. L, Jones, E. L. Messier, George Mesta, J. H. Jones, G. H. Riley, S. L. Goodale, D. W. McNaugher. LADIES' COMMITTEE.-Mrs. Taylor Allderdice, Chairman; Mrs. Julian Kennedy, Mr. R. C. Crawford, Mrs. E. M. Herr, Airs. J. W. Marsh, Mrs. T. A. Mellon, Mrs. G. P. Bassett, Jr., Airs. D. M. Clemson, Mr. Charles L. Miller, Mrs. V. L. P. Shriver, Mrs. W. A. Bostwick, Mrs. A. C.. Dinkey, Mrs. A. P. Childs, Jr., Mrs. F. R. Dravo, Mrs. Hermon Griffin, Mrs. W. H. Nimmick, Mrs. F. H. Lloyd, Mrs. S. G. Cooper, Mrs. S. H. Church, Mrs. E. N. Ohl. The Institute Headquarters was established at the Hotel Schenley, where a bureau of information was maintained for the benefit of the visiting members and guests of the party during the time of the meeting. TECHNICAL SESSIONS. The first session, held Tuesday evening, Mar. 1, 1910, in the large lecture hall of the Carnegie Institute, was called to order by Harrison W. Craver, Secretary of the Local Committee. Mr. Craver introduced Dr. John A. Brashear, who extended to the members and guests a hearty welcome to the city of Pittsburg, to which David W. Brunton, President of the Institute, responded. The following papers were presented in oral abstract by the authors: Biographical Notice of Dr. Charles B. Dudley, by Dr. R. W. Raymond, New York, N. Y. Biographical Notice of William Metcalf, by Col. II. P. Bope, Pittsburg, Pa. Development of Hindered Settling Apparatus, by Robert H. Richards, Boston, Mass. (Illustrated by lantern-slides.) A Few Mining Districts in the Argentine Republic, South America, by Z. S. Beyl. (Illustrated by lantern. slides.)

Apr 1, 1910

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNS Chairman. JOHN H. JANEWAY, Vice-Chairman. F. E. PIERCE, Secretary 35 Nassau St., New York, N. Y. P. A. MOSMAN, Treasurer. LEWIS W. FRANCIS. BENJAMIN B.. LAWRENCE. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. HENRY A. WENTWORTH, Secretary-Treasurer, 60 India St., Boston, Mass. A. H. EUSTIS, F. G. STANTIAL. Columbia Holds four sessions during year. Annual meeting in September or October. STANLY A. EASTON, Chairman. FREDERIC KEFFER, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON, FRANK A. ROSS.

Jan 5, 1916

By Theodore B. Counselman

Of all natural resources, iron ore made into steel is the most important both in tonnage and value. The primary reason for the prosperity of the United States in the last century has been its pre-eminence in domestic supplies of iron ore and steel. The depletion of these reserves by two world wars and by the demand for richer blast furnace charges, as well as the constantly growing world- wide demand for steel, has fostered the recent quest for new iron ore mines around the globe. These developments have made a dramatic change in the iron ore picture of the world. It is the purpose here, however, to look briefly at the development of the United States iron ore industry, which has played such an important role in the events leading to the modern day boom in iron ore exploration.

Jan 7, 1965

By F. S. Pettit

The oxidation of Ni-3 to 25 wt pd Al alloys has been studied in 0. 1 atm of oxygen at temperatures between 900° and 1300°C. These alloys have been found to oxidize by three different mechanisms which depend on the temperature of- oxidation and the alloy composition. Two of the three mechanisms do not permit a continuous layer of Al,0, to be formed on the alloy surface and the oxidation rates are greater than that for pure nickel. The third mechanism results in the formation of an external A1203 scale and lke oxidation rates are about three orders of magnitude smaller than those for pure nickel. The minimum amount of aluminum required for the formation of external scales of A L,0, has been determined. NICKEL-base alloys are currently the main source of materials for use at elevated temperatures in gas turbine engines. These alloys are usually coated to obtain oxidation resistance. Coatings on nickel-base alloys are frequently formed by reaction of the alloy with aluminum whereby alloyed nickel aluminides are formed. The alloyed nickel aluminides provide protection to the nickel base alloy because external scales of A1203 (alumina) are formed during oxidation and mass transport through A120, is slow in comparison to mass transport through most other oxides. In view of the protective properties of A1203, it is important to know how much aluminum is required in these alloys in order to form external scales of AlzO,. The present paper is concerned with the oxidation kinetics and the oxidation mechanisms of Ni-A1 alloys and the minimum amount of aluminum required in these alloys for the formation of external scales of Alz03. THEORETICAL CONSIDERATIONS When a Ni-A1 alloy is heated in oxygen at elevated temperatures, the following reactions can take place on the surface of the alloy where the oxide phases are assumed to be virtually pure: These oxide phases are in the form of nuclei scattered over the surface of the alloy and, in view of their rapid formation, they need not be in equilibrium with the alloy. As the oxidation process continues, equilibrium between the alloy surface and the oxide phases is approached and the stability of the oxide nuclei is determined by the composition of the alloy at the alloy/oxide interface because of the following reactions: 3NiA1204 + 2A1 (alloy) = 4AlzO3 + 3Ni (alloy) [41 4Ni0 + 2Al (alloy) = NiA120, + 3Ni (alloy) [ 5 1 Application of the mass-action law to Eqs. [4J and [5J yields the following equilibrium conditions for these reactions: where aA1 and aNi are the activities of aluminum and nickel, are the standard free energies of formation of NiO, A1203, and NA1204, respectively, R is the gas constant, and T is the absolute temperature. If the composition of the alloy at the alloy/oxide interface is such that (akl/ahi) is greater than the equilibrium values defined by Eqs. [6] and [7], then Reactions (41 and [5] will go to the right as written. Conversely, if the alloy composition is such that the activity ratio (aLl,/aki) at the alloy/oxide interface is less than the equilibrium values, then Reactions [4] and [5] will proceed to the left. The equilibrium activity ratios in Eqs. [6] and 171 can be calculated since values for the standard free energies of formation of the oxide phases are available. Standard free energies of formation for NiO and A1203 have been tabulated by Elliott and ~leiser.' The standard free energy of formation for NiA1204 can be obtained from the data of Tretjakow and Schmalzried.' The results of these calculations are tabulated in Table I. Table I shows that the following inequality is valid over the temperature interval 900" to 1300°C: (Reaction [5]) (Reaction [4]) « 1and therefore the aluminum activity for these compositions can be taken as equal to the square root of the activity ratios (i.e., aNi = 1). If equilibrium is estab-

Jan 1, 1968

By W. T. Weller

In Part I, a study of pressure build-up curves calculated for conditions under which both oil and gas flow led to the conclusion that the presence of a dispersed free gas phase in an oil reservoir must be taken into consideration to estimate accurately average reservoir pressure and permeability from build-up curves. Familiar methods based on the assumption of no free gas can be extended to the two-phase case by using total compressibility and mobility in place of single-fluid compressibility and mobility. These methods give correct values for average pressure and permeability when gas saturation is small. Errors become larger as the gas saturation increases. However, for the use to which the results will be put, the methods are satisfactory for reservoir engineering purposes. An improved method of calculating the performance of depletion-type reservoirs is presented in Part 2. Because the mathematical relationships describing simultaneous flow of oil and gas are quite involved. simplifying assumptions are made to provide means of obtaining approximate solutions of reasonable accuracy. One such approximate method now in use is the constant-GOR solution. It involves the assumption that at any instant, the ratio of total gas flow rate (both free and disolved) to oil flow rate is the same at all points in the reservoir. The approach is not applicable unless the free gar saturation in the reservoir is everywhere greater than the critical gas saturation. This paper presents a modification which, by avoiding the constant-GOR assumption, makes the method applicable to all reservoir conditions, and so far appears to be more accurate than the constant-GOR solution and to he comparable in required compuctation time. PART I— BUILD-UP CURVE ANALYSIS INTRODUCTION Pressure build-up characteristics of shut-in wells have been used for many years by engineers to evaluate average reservoir pressure, effective permeability thickness of the pay section, effectiveness of well completion (skin effect) and reservoir size. A number of methods of analysis have appeared from time to time."" Without exception, these methods are based on the assumption that the reservoir contains but one fluid of constant small compressibility and constant mobility. It has been suggesteda" hat these single-fluid methods may be applied to data from reservoirs containing both oil and gas by substitution of some effective total properties of the multiphase system in place of the corresponding single-phase properties. The present investigation was undertaken primarily to evaluate this approach. METHOD A number of theoretical build-up curves were calculated for conditions of two-phase flow, under the assumption of certain reservoir and fluid properties, and were analyzed by single-fluid methods with appropriate total compressibility and total mobility values for the corresponding single-fluid properties. Results of the analyses were compared with the assumed conditions. The theoretical build-up curves were completed by procedures similar to those of West, Garvin and Sheldon." Since these calculations require a considerable amount of computer time, an attempt was made to derive an approximate calculation method. The attempt was unsuccessful for calculating build-up curves, but the effort did result in a new approximate method of calculating the performance of solution gas drive reservoirs, which appears to be an improvement over the constant-GOR method" used previously (see Part 2). The West, Garvin and Sheldon calculations involved the following assumptions: (1) the reservoir is circular and completely bounded, with a completely penetrating well at its center; (2) the porous medium is uniform and iso-tropic, with a constant water saturation at all points; (3) gravity effects can be neglected; (4) compressibility of rock and water can be neglected; (5) the composition and equilibrium are constant for oil and gas; (6) the same pressure exists in both the oil phase and the gas phase; and (7) no afterproduction occurs, i.e., the well is shut in at the sand face for build-up. These assumptions make it possible to describe two-phase flow of oil and gas by the partial differential equations:

Jan 1, 1967

[NOTE.-The names of authors of papers are printed in small capitals, and the titles of papers, in italics. Casual notices, giving but little information, are indicated by bracketed page numbers. Large Roman numerals are volume numbers; small Roman numerals after volume numbers following titles indicate the page on which the presentation of the paper is mentioned; Arabic figures refer to the text of the printed papers.] A Use Classification of Coal, (ASHLEY) LXII [xiv]; LXIII, 782; Discussion: (HALL), 794; (ZERN) , 795; (ASHLEY), 795 Absorbent material, liquid-oxygen explosives, LXXI, 1251. Absorbents for liquid-oxygen explosives, LXIX, 292, 299. Absorption : cupellation : gold, special cupels, LIX, 194. primary and secondary, LIX, 213. ratio of silver to gold, LIX, 212. silver, specla1 cupels, LIX, 195. Absorption method, gasoline from natural gas, LIX, 584, 585. Absorptzon of Sulfur from Producer Gas zn Open-hearth Furnaces (NEAD), LXX, 176; Discussion: ( WATERHOUSE), 184 ; (REYNDERS) , 184; (KINNEY), 184 Accelerated wearing tests, bearing metals, LXIX, 973. Accident prevention, results, Utah, LXVIII, 360 Accident Prevention, 1919 (SINN), LXIII, [xiii] Accidents: causes in coal mines, LXXI, 1229. classification, Anaconda Copper Mining Co., LXVIII, 9. coal mining: comparison with metal mining, LXVIII, 360. pillar mining, LXVIII, 323. relation to method, LXVIII, 323 shafts, LXVIII, 207, 209 Utah, LXVIII, 363 - concentrating mills, Utah, LXVIII, 362 liquid-oxygen explosives, LXIX, 330, 339 losses through, LVIII, 65 metal mining, LXVIII, 361, 363. mine: causes, LIX, 652. curve of decrease, LIX, 655 days of greatest frequency, LIX, 657 human element as cause, LIX, 652, 653. intemperance as cause, LIX, 658 labor relation, LIX, 652 prevention, LIX, 653. record, New Jersey Zinc Co., Franklin mine, LIX, 655 time of greatest frequency, LIX, 657, 658 Utah, LXVIII, 360 prevention, LVIII, 65 report blanks, Anaconda Copper Mining Co, LXVIII, 13, 15. statistical base, Anaconda Copper Mining Co, LXVIII, 9 time lost, LVIII, 70 transportation, Clifton-Morenci district, LXX, 851.

Jan 1, 1926

EXECUTIVE COMMITTEES OF LOCAL SECTIONS Arizona E. P. MATHEWSON, Chairman W. V. DECAMP, First Vice-chairman F. W. MACLENNAN, Second Vice-chairman E. D. GARDNER, Secretary-Treasurer, U. S. Bureau Of Mines, Tucson, Ariz. MICHAEL CURLEY J. P. HODGSON HENRY F.1 ASTER CLYDE E. WEED Boston Meets first Monday each winter month GEORGE A. PACKARD, Chairman FRANKLIN B. RICHARDS, Vice-chairman F. LEROY FOSTER, Secretary-Treasurer Rooms 8-219 Mass. Inst. of Tech., Cambridge, Mass. G. W. METCALFE D. H. MCLAUGHLIN

Jan 1, 1932

By William Cruger

OUTLINE SUMMARY A. Brief Description B. Characteristics 1. Can be highly cost effective 2. Restricted in usage 3. Political Controversy 4. Volume of Transactions 5. Users C. Mechanism 1. Five steps D. Investor issues 1. Application 2. Restricted usage 3. Discount 4. Formal or informal process 5. Restricted benefits 6. Recompense 7. Window of opportunity THE VARIOUS PROGRAMS1 A. Brazil B. Chile C. Venezuela D. Argentina E. Mexico USAGE IN THE MINING, METALLURGICAL, AND PETROLEUM INDUSTRIES

Jan 1, 1990

By E. Swartzman, G. C. Behnke

THE free-swelling index, a numerical value for the free-swelling properties of coal, is being used to an increasing extent in specifying coal for burning in various types of equipment. The empirical standard ASTM method for determining this index uses, as a source of heat, a gas burner which requires frequent calibration because gas pressures are not constant, relatively small changes in gas pressure resulting in rather wide variations in the temperature attained in a crucible and thus in the resultant size of the coke button. Furthermore, the quartz crucibles specified for the test are not standard equipment, and relatively small variations in dimension and wall thickness from those specified often result in rather wide variations in the resultant size of the button. A method of analysis to be satisfactory not only for a scientific laboratory but also for use in industrial control laboratories under varying conditions should employ equipment which is rugged, easily calibrated, and readily replaceable by standard materials. Gas is not universally available as is electricity, and it is generally easier to calibrate and control a simple electric furnace or heater than a gas burner, the voltage not usually fluctuating to the degree that gas pressure does. Quartz crucibles are fragile, and the size specified in the test is not normally used for any other purpose in the laboratory. Although more expensive, the 15-cc platinum crucible, available in all laboratories where volatile matter in coal is determined by the standard ASTM method, is sturdy and standard and easily replaced. Because of these considerations, a modification of the standard method has been developed which employs a standard laboratory 350-w cone heater and standard 15-cc platinum crucibles. The results of numerous tests conducted with such apparatus show conclusively that the free-swelling index values as judged by the buttons produced with this equipment are exactly the same as those obtained by the standard gas burner method. Thus it is suggested that this electric cone heater method employing standard 15-cc platinum crucibles be considered as an alternative to the ASTM method, Designation: D720-46. The free-swelling index of coal is determined by means of the ASTM method, D720-46. This method, which is an adaptation of the crucible swelling test for coal of the British Standards Institution, consists of heating 1 g of coal in a special covered quartz crucible in a regulated gas flame for a period of not less than 2.5 min in which time the temperature of the inner surface of the bottom of the crucible reaches a temperature of 82025°C. The residual coke button is then compared in size and shape with a series of standard profiles shown in Fig. 1 and designated by number from 1 to 9 in increasing order of size. As the method is empirical, it requires rigid standardization of the apparatus and repeated calibration of the gas burner. The dimensions of the low form quartz crucible recommended must be rigidly adhered to as small variations in diameter or wall thickness result in variations in the rate of heat transmission and thus in the resultant size and shape of the coke button. The gas burner must be calibrated almost every time a new set of determina-

Jan 1, 1952

(There are 70 Student Chapters in the United States, 2 in Canada) University of Alabama-University, Alabama, Mining and Metallurgical Society, Win L Mason University of Alaska-College, Alaska, Mining Society of the University of Alaska, E H Beistline University of Arizona-Tucson, Arizona, Miners Society Birmingham-Southern College-Birmingham, Alabama, Pick and Hammer Club, Daniel D Arden University of British Columbia-Vancouver, British Columbia, G M Dawson Club, H C Gunning University of California-Berkeley, California, Mineral Technology Association, W H Somerton Carnegie Institute of Teehnology-Pittsburgh, Pennsylvania, The Metals Club, Gerhard Derge Case Institute of -Technology-Cleveland, Ohio, Case Metallurgical Engineering Society, Robert F Hehemann

Jan 1, 1956

DR FRANK DAWSON ADAMS Montreal, Canada HENRY STURGIS DRINKER Bethlehem, Pa PROF HATON DE LA GOUPILLIERE Paris, France SIR ROBERT A. HADFEILD London, England HERBERT C. HOOVER Leoben, Austria ROBERT W. HUNT Chicago, ILL JAMES FURMAN KEMP New York, N.Y. PROF HENRI LOUIS LE CHATELIER Paris France EZEQUIEL ORDONEZ Mexico City, Mexico ALEXANDRE, POURCEL Paris, France RICHARD H, RICHARDS Boston Mass. JOHN E. STEAD Middlesborugh, England PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia CHARLES D WALCOT Washington D.C.

Jan 1, 1923

CONTENTS PAGE Bronze Bearing Metals. By G. H. CLAMER 1729 Pennsylvania Railroad Anti-friction and Bell Metals. By F. M. WARING . . 1733 The Tin-plate Industry. By D. M. BUCK. Discussed by G. H. CLAMER, J. W. RICHARDS 1735 The Aluminum Bronze Industry. By W. M. CORSE 1738 Bronzes, Bearing Metals, and Solders. By G. K. BURGESS and R. W. WOODWARD. Discussed by G. H. CLAMER, R. T. ROBERTS 1742 Babbitts and Solder. By G. W. THOMPSON 1751 The Cadmium Supply Of the United States. By C. E. SIEBENTHAL. Discussed by M. L. LISSBERGER, C. W. HILL, F.- F. COLCORD . . .. . . . . 1752 Solder, Its Use and Abuse. By M. L. LISSBERGER 1759

Jan 12, 1918

By W. B. Braden

This paper presents a suitable method for predicting gas-free oil viscosities at temperatures up to 500F knowing only the API gravity of the oil at 60F and the viscosity of the oil measured at any relatively low temperature. The API pravity and the one viscosity value are used as parameters to determine the slope of a straight line on the ASTM slanaord viscosity-temperature chart. Then, knowing the slope of the line and one point on the line, the vrscosities at higher temperatures can be determined. The line slope correlations were developed at I00 and 210F since viscosity data are frequently measured at these temperatures. A procedure is given for predicting line slopes from measurements at other tetnperatures. A nomogram is furnished for solving the relationship. The correlation has been evaluated at temperatures up to 5OOF for oils varyzng in gravity from 10 to 33 " API. The correiution is applicable only to Newtonian fluids. Comparison at 500F of true viscosities and those predicted from values at 100F shows an average deviation of 3.0 per cent (maximum deviation of 6.0 per cent). Predictions from the values at 21 0F for the same oils how an average deviation of 1.5 per cent (maximum deviation of 3.4 per cent). INTRODUCTION Correlations have been developed by Beal' and by Chew and Connally' for predicting viscosities of gas-saturated oils at reservoir conditions. Each of these correlations requires a knowledge of the solution gas-oil ratio and the viscosity of the gas-free oil at the reservoir temperature. For temperatures below 350F, measurements of the gas-free oil viscosities can be made easily using commercially available equipment. In thermal recovery processes, however, reservoir temperatures well in excess of 350F are encountered. Viscosity measurements at such conditions are more difficult and time consuming and require modification of existing equipment or the construction of new equipment. Measurements are further complicated by the difficulty of handling highly viscous oils associated with thermal recovery processes. Therefore, it is desirable to have a correlation which allows accurate prediction of viscosities at high temperatures. A commonly used technique for predicting viscosities at high temperatures is to measure the viscosities at two lower temperatures, plot the values on ASTM standard viscosity-temperature charts and extrapolate to the temperatures desired. If either of the values is slightly in error, the extrapolated value can be significantly in error. To justify an extrapolation, three points are actually necessary. This procedure can consume much time, particularly with heavy oils. Considering the cost of viscosity measurements, it would be desirable to eliminate the need for direct measurements by having correlations which would allow viscosity predictions from other physical or chemical properties. Beal1 investigated the possibility of correlating viscosity with oil gravity at temperatures from 100 to 220F. While showing that a general relationship exists, he also found significant deviations. It is possible that correlations will be developed based on oil composition as more information becomes available. While not eliminating the need for viscosity rneasurements, the method presented herein requires that only one viscosity measurement be made. The API gravity must also be known. The theory is based on the fact that the viscosity of paraffins (high gravity) changes less with temperature than does the viscosity of naph-thenes or aromatics (low gravity). The gravity. therefore, is used as a parameter to determine the slope of a straight line on the ASTM standard viscosity-temperature charts. The correlation is applicable only to Newtonian oils, and deviations due to thermal decomposition and nonhomo-geneity cannot be predicted. Oils containing additives have not been evaluated. PROCEDURE Fifteen oils were used in developing the correlation; eight were crudes and seven were processed oils. Oil gravities varied from 9.9" API (naphthene base) to 32.7' API (paraffin base). The temperature range studied was 81 to 516F. Each oil used had a minimum of three viscosity measurements and each plotted essentially as a straight line on the ASTM charts. In all, 91 viscosity measurements were used in the correlation. Saybolt, rolling ball and capillary tube viscometers were used for the measurements. Viscosity data for Samples 1, 2, 4, 7, 10, 11 and 14 were obtained in Texaco, Inc. laboratories. The data for Samples 3, 5, 6, 8, 9, 12 and 15 were from Fortsch and Wilson,3 and data for Sample 13 were from Dean and Lane.' All data points used in the correlation are plotted in Fig. 1. It is seen that some of the viscosity values deviated slightly from the straight-line plots at the higher temperatures. Properties of the oils after exposure to the

Jan 1, 1967