Search Documents

Executive HOWARD N EAVENSON, Chairman FREDERICK M. BECKET EDGAR RICKARD ERLE V. DAVELER WILLIAM WRAITH Finance HENRY KRUMB Chairman PAUL D. MERICA J V W REYNDERS H G MOULTON, Consultant Admissions JOHN M LOVEJOY, Chairman GEORGE D BARRON - DONALD M LIDDELL ELI T CONNER - WILLIAM W LYNCH

Jan 1, 1935

By K. A. Gschneidner, O. D. McMasters, T. J. O’Keefe

X-ray diffraction, differential thermal, ad rnetallo-graphic methods were used to establish the Dy-Pb Phase diagram. Lead additions lower the 1377°C transformation temperature of dysprosium to 1360°C leading to an inverted peritectic reaction. The 327°C melting point of lead is lowered by dysprosium additions to about 326°C yielding a eutectic reaction. A second eutectic reaction occurs at 13.3 at. pct Pb and 1200°C. The dysprosium-richest intermetallic compound DysPb3 melts congruently at 1695°C and crystallizes in the hexagonal Mn5Si3 (D8,) type structure. The peritectic decomposition temperatures for the remaining compounds are Dy5Pb, at 1555C, DyPb2 at 955C, and DyPb3 at 880°C. A fifth compound near the DyPb stoichiometry exists over a 310°C temperature range decomposing at 1130°C by means of an inverted peritectic reaction and melting incongruently at 1440°C. The crystal structures of the compounds are discussed. A systematic study of the rare earth-lead alloy systems is underway in an effort to supply information concerning the alloying behavior of the rare earth metals. The Dy-Pb phase diagram is the fourth system to be investigated in this study. The Yb-Pb,1 Y-Pb,2 and Eu-Pb 3 diagrams have been published recently. Utilization of the rare earth series of metals as a research tool in this manner should yield a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The lead used in this investigation was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The dysprosium was prepared in this Laboratory by the calcium reduction of the fluoride followed by distillation of the dysprosium. The major impurities in the dysprosium in ppm are: A1 (<40), Ca (400), Er (<50), Gd (<200), Ho (<200), Mg (<50), Si (30), Ta (400), Tb (<100), Y (<50), 0 (651, H (15), N (not detected), F (430), C (35). Alloy Preparation. Most of the alloys were prepared by melting weighed amounts of dysprosium and lead in sealed tantalum crucibles. The tantalum crucibles were sealed by are-welding in a He-Ar atmosphere welding chamber. Thus the alloys are in contact with He-Ar at about 1 atm pressure. Homogenization was achieved by holding them in the liquid state for about 1 hr, cooling, inverting the crucibles, remelting, and repeating the process at least twice. Since these alloys were prepared in sealed tantalum crucibles, chemical analysis for final composition was thought to be unnecessary. No detectable reaction of these alloys with the tantalum crucible was observed by metallographic examination. Metallographic evidence was also used to confirm the homogeneity of some of the alloys prepared in this manner. The compositions of a few alloys, which were prepared by nonconsum-able are-melting, were corrected for the small weight losses involved by assuming that the weight loss is due to vaporization of lead. The specimens obtained from the alloy samples were prepared under a dry-argon atmosphere because they were rapidly attacked by air and moisture. Thermal Analysis. Differential thermal analysis methods were used to determine the liquidus curves and reaction horizontals of the system. Both Pt vs Pt + 13 pct Rh and W + 5 pct Re vs W + 26 pct Re thermocouples were used to measure the temperature. An X- Y recorder was used to record the specimen temperature and differential electromotive force between the specimen and molybdenum standard. The arrest temperatures were measured potentiometri-cally. The accuracy limits (* values) associated with the reaction temperatures obtained by this method were estimated on the basis of both the reproducibility of the particular temperature value and the accuracy of the thermocouple at a given temperature. Liquidus temperatures were obtained from cooling arrest data while both heating and cooling arrest data were used to establish the horizontals of the diagram. Heat treatments during the thermal analyses of the alloys between 40 and 70 at. pct Pb were necessary in order to approach equilibrium conditions. The samples were held at temperatures between the various peritectic horizontals for l to 2 hr before the thermal analyses were continued. The entire range of compositions was investigated at the expense of a minimum amount of materials by adding appropriate amounts of lead to master alloys. More than sixty alloys were analyzed by this differential thermal method and for each alloy the results given herein are taken from two or three heating and cooling cycles. X-Ray and Metallographic Methods. Slice specimens for metallography and powder specimens for X-ray diffraction were prepared from rod-shaped samples which had been melted in sealed 0.62 5-cm-diam tantalum crucibles. The specimens were heat-treated in sealed tantalum crucibles which were protected by sealing them in argon-filled quartz ampules. Quenching was accomplished by breaking the ampules in ice water after heat treatment. X-ray powder specimens were sealed in 0.3-mm-diam glass capillaries under a dry-argon atmosphere. Copper, iron, and chromium radiation were used to obtain the powder patterns for these alloys. More than 150 powder patterns were obtained for specimens of various compositions and heat treatments. Included in these were several patterns for specimens which had purposely been oxidized. Patterns from specimens which had been accidentally exposed

Jan 1, 1969

By T. Rosenqvist

From the chemical, metallurgical, and mineralogical points of view, the importance of thermodynamic data for metal-sulphides and sulphur dissolved in molten metal has long been realized. Such data will give a basis for thermo-dynamic calculations of processes such as roasting and the distribution of sulphur between molten metal and slags. Furthermore, it will help us understand the chemical forces which tie sulphur to the metal and to the melt. Thermodynamic studies of solid sulphides and the equilibria between solid sulphides and metals have been carried out in a rather large number of cases by several investigators. An excellent review of this work is given by Kelley.1 On the other hand, very little is known about the thermodynamic properties of molten sulphides and of sulphur dissolved in molten metal. The only system which previously has been investigated in this respect is the iron/sulphur system. The purpose of the present investigation was primarily to obtain further data for metalisulphur melts and the system silver/sulphur was chosen, not because this system was expected to be of special interest in itself, but because the silver/sulphur system is a typical example of a metal/sulphur system. Because of the low melting temperatures, the work could be carried out without appreciable furnace and refractory difficulties. The sulphur in this system possesses a rather high escaping tendency compared to most other metal/sulphur systems. By the method employed (reaction with hydrogen to form hydrogen sulphide) this gives ratios Ph2s/Ph2 up to 0.30, which may be determined accurately. &apos;rhermodynamic investigations of the heterogeneous reaction Ag2S +H2 —+ 2Ag + H2S have previously been carried out by Pelabon,2 Keyes and Felsing,3 Jellineb and Zakowski,4 Wat-anabe,6 and Britzke and Kapustinsky.6 Their results are in rather poor agreement. Experimental Part PRINCIPLE In the present invehgation the escaping tendency of sulphur from the condensed phase was determined by the reaction: S + H2 = H2S The ratio Ph2s/Ph2 is at constant temperature, directly proportional to the escaping tendency of sulphur and to its chemical activity in the condensed phase. (This ratio will subsequently be denoted by H2S/H2.) From this ratio and its variation with temperature and with change in the com- position of the condensed phase, thermodyrlamic quantities such as free energy and heat of reaction can be derived. The apparatus used is shown in Fig 1. The silver/sulphur alloy was placed in a crucible inside a refractory tube and mounted inside the furnace to the left. The tube was a part of a closed, gas-tight system in which the gas mixture could circulate until equilibrium was established. Circulation was maintained by the glass propeller to the right, driven by an external magnet, and promoted by the chimney action of the furnace. The gas passed up through the furnace, down into the crucible where it came in contact with the alloy, passed rapidly up through a narrow tube and out of the hot zone. After equilibrium was established between the gas and the condensed phase, the composition of the gas mixture was determined from its density. In its circulation, the gas mixture passed through a chamber (lower right on Fig 1) containing a buoyancy-balance, where the density of the gas was determined by magnetic balancing. From the measured density,

Jan 1, 1950

By Everett D. Jackson

The largest deposits of chromite in the United States occur in tabular layers in the lower part of the Stillwater Complex, Montana. Nearly 900,000 long tons of chromite concentrates have been produced from mines and mills in this area, and reserves equivalent to more than 2,500,000 long tons of Cr2O3 remain in the ground. Layered concentrations of chromite (known as chromitite zones) occur only within olivine-rich layers of the Peridotite member of the Ultramafic zone of the Stillwater. As many as thirteen chromitite zones, lying conformably one above another, have been found, but only five of them are thick enough to be of any conceivable economic interest, and only two of them have been mined to date. Individual chromitite zones can be recognized by their distinctive internal character and by their stratigraphic position in the Peridotite member. The chemical composition of chromite varies consistently between and within the different chromitite zones. The zones range in thickness from about an inch to more than 12 feet, and the Cr2O3, content of their chromite ranges from 36.6 to 49.2 weight per cent. In any given area, the G chromitite zone is the thickest, but the chromite of the H chromitite zone has the highest grade. Laterally, the thickness of the chromitite zones is related to the thickness of the Peridotite member; in general all are thicker in the eastern part of the Stillwater than in the western part.

Jan 1, 1968

By J. C. McKinnell

The appraisal of an oil lease may often be mad,? through production decline analysis, which requires description of the functional relationship between the oil production rate and either cumulative production or time. Heretofore, attempts to define the function appropriate to a given set of production data have depended to some extent on subjective procedures. The purpose here is to introduce an objective solution, obtained by combining the principle of least squares with the theory of equations. MATHEMATICAL ANALYSIS The fundamental differential equation appropriate to a general class of decline curves may be written. Solution of Eq. 1 for general boundary conditions may be written in terms of either the cumulative oil production or time: These equations constitute the mathematical expression of the so-called hyperbolic decline. Their complete description for a given set of production data requires the numerical evaluation of the three parameters1.&apos;, n, D, and (go),. For the special case of n = 0, Eq. 2 becomes q. = (q.), - DiN with the corresponding expression in terms of time being q. = (qa),e...........(5) Similarly, for the special case of n = 1, Eq. 3 becomes with the corresponding expression in terms of cumula- tive oil production being q. = (q.),e " &apos;.......(7) Eqs. 4 and 5 constitute the mathematical description of the so-called exponential decline; Eqs. 6 and 7 are the mathematical description of the harmonic decline.&apos;,&apos; Returning to the hyperbolic expressions, Eqs. 2 and 3 may also be written, q: = sNp + b........ (8) and where a = 1 - n; s = (n— 1)D,(q0);"; b = (go):-"; a&apos;=-n;s/= nD,(qo);"; and b&apos; = (go);-. Note that both Eqs. 8 and 9 are linear in either time or cumulative production with respect to an exponential function of the production rate. In other words, a straight line relationship results for both variables when associated with the appropriate power of q,. This fact is of prime importance in the application of statistical analysis. . STATISTICAL ANALYSIS For a given oil lease, the time, production rate and cumulative production are recorded records. To establish predictive formulas from Eqs. 2 and 3, it remains to determine numerical values for the three parameters [n, D, and (q,) .] through an investigation of the past history. Upon interpreting a, s and b as parameters, Eq. 8 may be expressed for every time interval of interest, i, over the past history as follows. (q,): = s(Np), + b........(10) In general, Eq. 10 will not be satisfied exactly, because of the assumptions in the expression of Eq. 1, and the errors and anomalies universally associated with production data. It will instead define the residual, s(Np), + b- CO=d......(11) Squaring both sides and summing over all the data points, m, under consideration yields

EXECUTIVE COMMITTEE OF THE BOARD OF DIRECTORS C. H. MATHEWSON. Chairman PAUL D. MERICA, Vice-Chairman CHESTER A. FULTON CARROLL A. GARNER H. Y. WALKER FINANCE COMMITTEE OF THE BOARD OF DIRECTORS ERLE Y. DAVELER, Chairman WILBER JUDSON RUSSELL B. PAUL HENRY KRUMB, Consultant

Jan 1, 1943

By J. A. Retty

IN the Labrador iron fields two concessions, totaling nearly 24,000 square miles, have been staked out and commercial-grade deposits delineated. The Newfoundland-Labrador concession, owned by the Labrador Mining and Exploration Co. Ltd., is a 20,000-square-mile tract in the upper basins of the Hamilton and N askaupi Rivers which drain into Lake Melville. The New Quebec licensed area is 3900 square miles, owned by the Hollinger North Shore Exploration Co. Ltd., lying to the northwest of the northwestern part of the Labrador concession. It includes the upper basin of the Swampy Bay River and part of the upper basin of the Whale River, both of which drain into Ungava Bay. Both of the above-named companies are controlled by Hollinger Consolidated Gold Mines Ltd. with The M. A. Hanna Co., of Cleveland, holding a minority interest. When exploration was first undertaken in 1936, the only published map of the area was that prepared by A. P. Low in 1895. It showed only the main watercourses and gave only a rough, general idea of the geology. The numerous lakes of this vast area had to be first sketched and then mapped. Since then, extensive geological and topographical surveys have been conducted by the Labrador company, work which is normally done by Government branches. The object of the work was to examine the area and gradually eliminate unfavorable or less favorable prospecting ground. With this object in view, geological

Jan 1, 1948

By DR. DOUGLAS

Discussion of the Paper of Dr. Douglas, presented at the Toronto Meeting of the Institute, July, 1907 (Trans., xxxviii., 455 to 471). EDGAR HALL, Silverspur, Queensland, Australia (communication to the Secretary*) :-Dr. Douglas has written on this subject before, and his influence has had a powerful effect on the side of freedom among the younger generation of engineers. Moreover, it is not the first time that he has attributed the decline of the copper-smelting industry in Swansea to the secrecy maintained by the firms there engaged in smelting-operations. In this latter statement I think his conclusions are open to criticism. Whether the firms referred to have suffered by their secrecy is their own business-I. bold no brief for them ; but that the decline of the copper-industry at Swansea was inevitable seems to me to be proved conclusively by Dr. Douglas&apos;s own writings. In his paper on The Copper Situation,1 Dr. Douglas says "In comparing iron and copper mining, . . . it must be remembered that 2 tons of average iron ore from the most prolific source now available will make 1 ton of metal; whereas from 33 to 75 tons (say an average of 50 tons) of copper ore must be mined to produce 1 ton of copper." And further: "Last year&apos;s production of iron was made from approximately 50,000,000 tons of ore. Our copper mines, to yield a production of 900,000,000 pounds, must have handled approximately 22,000,000 tons of ore, or nearly half the quantity raised from our iron mines." Is not this the key to the whole situation ? In transporting the 50,000,000 tons of iron-ore, 25,000,000 tons of the metal iron were carried so much nearer to the market, but the transportation of 22,000,000 tons of copper-ore would have carried only 450,000 tons of the metal copper nearer to its ultimate destination. The small percentage of copper available in its ores makes

Sep 1, 1908

By J. Alfred Berger, O. M. Katz

Selected samples of hydrided Zr-Hf alloys were rapidly quenched to voom temperature and exrtrnined metallographically, by X-ray diffraction, and through micro hardness studies to confirm high-temperutuve data Confirming experiments sllowed that there were five phases in this Lernary system: 1) hextrgonal with lattice parameters similar to that of the initia1 Zr-Hf alloy but slightly enlarged due to dissolved hydrogen; 2) fee with properties of a brittle, intermediate, hydride compound; 3) fct with c/a crvoltnd 1.07 and which appeared as a neetilelike precipitale; 4) hexagonal, designated ?, with c/a ratio of 2.37; and 5) orthorhombic, designated X, with a = 4.67, b = 4.49, and c = 5.093 and whose tnicro-st?ruct~ival nppetrl-nnce depcncled o/i, heat lvecrt~r~ent. The tetragonrrl phase never crppeal-erl witkorct the cubic hydricle. Abpecrrtrnce of 0 and A also tlependet on the hafnium content of the zirconium. A previous paper&apos; on the Zr-Hf-H system described the thermochemical data obtained with a high-vacuum, high-sensitivity mirrogravimetric apparatus. This data presented a fairly complete picture of the phase relationships at elevated temperatures. However, it could not establish the actual crystal structures, lattice parameters, or metallographic disposition of the hydride phases. The present complementary study utilizes X-ray powder patterns along with light and electron microscopy to characterize completely the five hydrided phases found in Zr-Hf-H alloys quenched to room temperature. Crystallographic features of the zr-Hf,2,4 zr-H,5-7 and Hf-H8 systems have been summarized in Table I. Designations of a, ß, and ? were retained in the Zr-Hf-H system for the phase regions through which the pressure-composition isotherms always sloped. However, it was not firmly agreed that these were single-phase regions.&apos; In fact, the region designated y always contained a cubic as well as a tetragonal phase after quenching to -196°C. MATERIALS Preparation of the high-purity Zr-Hf alloys has been described.&apos; The four zirconium alloys which were hydrided contained 37 wt pct Hf (23 at. pct), 51 wt pct Hf (37 at. pct), 73 wt pct Hf (58 at. pct), and 91 wt pct Hf (82 at. pct), respectively. These were designated B-2, B-4, B-6, and B-8. Photomicrographs of the initial alloys showed the material to be quite clean as would be expected from the precautions exercised in producing them. However, there were a number of annealing twins but no other subgrain structure. In addition to the four original alloys, fifteen hydrided samples were observed at room temperature. Hydrogen compositions are given at the top of Tables I1 to V. APPARATUS The phases present at elevated temperatures were studied by quenching hydrided samples to room temperature by two different methods, both under vacuum: 1) fast cooling of the sample tubes of the microgravimetric apparatus1&apos;9 with flowing air and 2) rapid quenching into liquid nitrogen. The cooling rate for 1) was 750° to 250°C in 30 sec. Since the microbalance chamber was not designed to permit very rapid cooling of a hydride sample, all liquid-nitrogen quenching was done in an auxiliary experiment. The auxiliary quenching apparatus consisted of a small-bore, high-temperature furnace, a sealed SiO2 tube containing the sample, and a dewar quenching flask filled with liquid nitrogen. The hydrided sample, previously quenched in the microgravimetric reaction chamber, was placed in a platinum boat in a vacuum-degassed SiO2 tube. A zirconium wire getter and degassed SiO2 rod, to reduce the internal volume, were also in the tube. After sealing the tube under vacuum the zirconium getter was heated to absorb the last traces of gas. Only the sample was heated at the reaction temperature for the desired length of time, and then the tube dropped through the opposite end of the furnace into the dewar. A quenching rate of 200" to 400° C per sec was estimated. Analyses of samples after the auxiliary experiment also showed practically no increase in oxygen or nitrogen content from heating in the SiO2 tube. All of the samples were examined at room temperature by the X-ray powder method. The majority of the powder patterns were obtained with double nickel-filtered CuKa radiation after 8- and 16-hr exposures in an 11.48-cm-diam camera. Cobalt and chromium radiation were also used to spread out the high d value end of the Pattern. Such patterns readily identified the minor phases. NO oxide or nitride lines were found. Where sharp back-reflection lines existed it was possible to reduce the

Jan 1, 1965

By V. M. Karve, K. K. Majundar, K. V. Viswanathan, J. Y. Somnay

The effect of calcium, magnesium, iron (both ferrous and ferric) and aluminum ions, which are commonly encountered in a typical beryl ore, was studied in the flotation of pure beryl, soda-feldspar and quartz. The vacuumatic flotation technique was employed. With sodium oleate as collector and in the absence of any activator, beryl floated in a pH range of 3 to 7.5, whereas feldspar and quartz did not float at any pH up to 11.5. The pH range of flotation increased in the presence of the ions studied. With calcium and magnesium ions beryl floated from 3 to 11.5 pH and beyond, soda-feldspar floated beyond pH 6 and quartz floated beyond pH 8. Ferrous ion activation was found to be similar to that of calcium and magnesium. Activation by ferric and aluminium ions was found to be complex and the lower and upper critical pH for all the three minerals was around 2 and 10 respectively. These studies indicated the possibility of separation of beryl from feldspar and quartz even in the presence of calcium, magnesium and ferrous ions between pH 4 and 6. Flotation tests on a mixed feed of pure minerals in a 10 g cell revealed that beryl can be selectively floated from feldspar and quartz if ferric ion is reduced to ferrous state or if it is complexed. Beryl occurs mostly in pegmatites, and hence is associated with feldspar, quartz and micas and small amounts of other minerals such as apatite and tourmaline. The separation of beryl from these minerals is difficult because all the silicates accompanying beryl have more or less the same physical properties. Specific gravities of beryl, feldspar and quartz are 2.70, 2.56 and 2.66 respectively. Electrostatic separation has been suggested but no work has been reported. &apos; The adsorption of sodium tri-decylate tagged with Cl4 on beryl, feldspar and quartz reveal similarity in surface properties. Much work has been reported on the flotation of beryl from ores, either directly or indirectly as a by-product, but little is known about the fundamental aspects of beryl flotation. Kennedy and O&apos;Meara3 laid emphasis on prior cleaning of the mineral surfaces with HF. Mica is removed first by flotation of beryl with oleic acid, around neutral pH. Runke4 introduced calcium hypochlorite conditioning in a final separation stage for activating beryl in a mixed beryl-feldspar concentrate, and after washing to remove the hypochlorite, floated beryl with petroleum sulphonate. The Snedden and Gibbs5 procedure is somewhat similar to that of Kennedy and O&apos;Meara. Emulsified oleic acid is used as collector. Recently Fuerstenau and Bhappu6 studied the flotation of beryl, feldspar and quartz with petroleum sulfonate in the presence of activators and stressed the importance of iron in the flotation of beryl. From the studies conducted in this laboratory, it was found that feldspar and quartz as such do not float with sodium oleate, but in practice selective flotation of beryl from feldspar and quartz in an ore is found to be impossible with sodium oleate as collector. A glance at the chemical analysis of typical beryl ore indicates the presence of several ions like Ca ++, Mg++, Al + + + and Fe+++ in abundance and Ti++++ and Mn++ in traces. Hence, in an attempt to explain the behaviour of feldspar in the beryl flotation, the effect of Ca++, Mg++, Al+++ and Fe+++, which are known as gangue mineral activators7&apos;8 has been investigated. Materials and Methods: Lumps of beryl ore (hand picked) were boiled with 10% sodium hydroxide and washed with distilled water. They were further boiled many times with 10% hydrochloric acid till no positive test for iron was obtained with ammonium thio cyanate. This was followed by thorough flushing with double distilled water. The lumps were crushed in a porcelain mortar and pestle under water. The minus 65 + 100 mesh fraction was used for testing and was always stored under distilled water. Pure feldspar and quartz were similarly prepared and the minus 65 + 100 mesh fractions collected. Inorganic ions tried as activators were ca++, Mg++ , Fe++, Fe ++ and A1 +++ . Calcium nitrate, magnesium chloride, ferrous ammonium sulfate, ferric ammonium sulfate and aluminum nitrate of G.R.E. Merck grade were used. B.D.H. technical grade sodium oleate was used as a collector. The vacuumatic flotation technique developed by Schuhmann and Prakash was used for studying the effect of pH on flotability. 7 The indications given by this work were confirmed by using 10 g miniature cell.&apos;

Jan 1, 1965

Jan 1, 1882

By Edgar C. Bain, William E. Griffiths

The results of an inquiry into the structural nature of some 70 iron alloys containing both nickel and chromium over a considerable range of concentration are briefly described in this paper. This study is a part of a comprehensive program of investigation into alloys involving chromium in progress at the Union Carbide and Carbon Research 1aboratories. All the compositions studied contained carbon in amount comparable to commercial alloys. The B Constituent In addition to locating the limits of composition for the three principal types of structure (polyhedral ferrite, martensite and austenite) and their combinations, certain other features of the system were observed. A hitherto undescribed brittle constituent (designated here as the "B constituent") was discovered. It is very hard, non-magnetic and forms in two modes from chrome-ferrite by recrystallization. It is the stable low-temperature condition for the equal-proportion chromium-iron materials containing less than 10 per cent. nickel. Although it partakes of the nature of an inter-metallic compound, yet it may exist over a considerable range of composition. It is non-existent above a temperalure zone, varying with composition, from 800° C. to 950° C., and heating above this critical temperature develops chrome ferrite persistent after average cooling rate; a few hours just below this temperature will develop the complicated brittle crystalline type. The B constituent, when found in the grain boundaries of alloys of lower chromium content, contributes a serious brittleness removable, however, by heating and cooling rapid enough to prevent its re-format&apos;ion. By suitable means of precipitution, the hard B constituent can be made to strengthen the already stiff alloy matrix in the manner of submicro-scopic particles, as exemplified in duralumin or the Sykes iron-tungsten and iron-molybdenum alloys. A possible explanation is offered for the familiar brittleness developed in chrome iron at temperatures above about 475" C. and removable by

Jan 1, 1927

By Reinhardt Schuhmann JR

Metallurgical Engineering Volume I, by Reinhardt Schuhmann, Jr. Addison-Wesley Press. $7.50, 390 pp., 1952. -This first volume, engineering principles, of a two volume work, is intended by the author to meet a need for reorganization of instruction in extractive metallurgy. Its three main objectives are to organize the subject matter according to basic principles and unit processes; to integrate the underlying science of physical chemistry with metallurgical engineering; and to put greater emphasis on analysis and quantitative solution of engineering problems. Vol. I deals with unit processes, stoichiometry, thermodynamics, fuels, fluid flow, heat transfer, pyrometallurgical systems and refractories. Vol. II will take up the individual unit processes. Initiation and Growth of Explosion in Liquids and Solids, by F. P. Bowden and A. D. Yoffe. Cambridge University Press. $4.50, 104 pp., 1952.-The book is a study of decomposition by impact and by friction of explosive substances and deals mainly with the work of the authors and their collaborators. Research is still in progress but results thus far indicate that the mechanism of initiation is relatively simple. Findings are thoroughly discussed, and the latter part of the monograph describes the way in which a small nucleus of decomposition can grow into a large scale explosion.

Jan 1, 1952

G. K. BURGESS, ? Washington, D. C.-At the Bureau of Standards it was decided, in order to study the high-aluminum end of these curves, that efforts should be made to prepare pure aluminum, and the promise of getting aluminum, practically free from the two elements that have such great effect in very small quantities, namely, silicon and iron, and which

Jan 12, 1919

By R. E. Salvoti

IN underground coal mining, the increasing trend towards mechanical methods is ever apparent. Figures for 1939 showed that 28 per cent of the total bituminous coal production was mined mechanically 1940 statistic will reveal an even higher figure. Factors causing this trend are varied, but the important are the following;

Jan 1, 1941

By John A. Emery

The Pea Ridge iron ore deposit near Sullivan, Missouri, is a dike-like mass of magnetite enclosed in Precambrian porphyries. The ore body tops at the Precambrian surface at a depth of 1300 feet below the present surface and extends to an unknown depth. It dips nearly vertically, intersecting the dip and strike of the enclosing porphyries at an extremely sharp angle. Faulting, both pre- and post-ore, appears to be of minor consequence, and present knowledge indicates that no preferred structural conditions existed prior to emplacement. The ore body is composed of magnetite with specular hematite, quartz, apatite, and pyrite occurring as accessory primary minerals. Specular hematite in appreciable quantities occurs on parts of the cap and the footwall of the ore body. Fresh porphyry breccia is enclosed in the magnetite along the hanging wall and in the western portion of the ore body. Hanging-wall quartz-amphibole and footwall quartz-hematite occur as replacements of certain porphyries. Further alteration has caused sericitization of parts of these zones. The ore deposit is interpreted as having been formed essentially by a single injection of a magmatic differentiate with hydrothermal end phases forming the quartz-amphibole and quartz-hematite portions of the deposit.

Jan 1, 1968

By C. WIFLARD HAYES

(New Haven Meeting, February, 1909.) I DESIRE to make it perfectly clear at the outset that I fully realize the hazardous nature of any attempt to estimate the quantity of iron-ore or any other mineral in the ground. I should not have had the temerity to venture upon an inventory of the iron-ore supplies of the United States except for the requirements of the Conservation Commission. During the preparation of this inventory I have been impressed by the wide diversity in estimates of those best qualified to. hold an opinion, and I am therefore prepared in advance for criticism of my figures. Inasmuch as this report was prepared in large part for unprofessional readers, I considered it necessary to classify and describe the commercial iron-ores in a somewhat elementary manner, in order to explain the reasons for the large element of uncertainty in the estimates. I have therefore given a chemical and a geological classification of iron-ores, which place the commercial deposits in six classes: (1) magmatic segregations in basic igneous rocks; (2) contact-deposits formed in connection with igneous intrusions; (3) concentration-deposits; (4) replacement-deposits; (5) bedded-deposits, and (6) gossan-deposits. The iron-ores are further distinguished under two classes available and not available. This classification is in large measure arbitrary, and it, is evident that it will vary front time to time. In the available class are placed those ores which can be worked at a profit under conditions essentially as they exist at present. Since it depends wholly on the question of costs, the various factors which affect cost will determine the classification of any particular deposit. Actual production, * Abstract of Report prepared for the Conservation Commission. t Chief Geologist, United States Geological Survey. .

Apr 1, 1909

By AIME AIME

THE Hazleton district of the Pennsylvania Anthracite Region will be the scene Oct. 14 and 15 of the fall meeting of the Coal Division and the Pennsylvania Anthracite Section. Here, coal mining has been active for more than 100 years and hereabouts industrial necessity inspired the numerous inventions of the Pardees, Eckley B. Coxe, a former A.I.M.E. president, and the Marltles, who contributed much to the success of the Institute in its early days, as well as to the upbuilding of modern methods in the anthracite and bituminous industries. Headquarters will be the Altamont Hotel, Hazleton, Pa. There will be two technical sessions Friday, registration preceding the first which is scheduled for 11 a.m. to 1 p. m. The second will be called at 2:30 p.m. Saturday is reserved for mine and plant visits, with golf and tennis after luncheon for those so inclined. The ladies are cordially invited to the meeting and arrangements have been made for their participation in much of the program. The chairmen of the committees preparing for the meeting are: Donald Markle, president, Jeddo-Highland Coal Co., General Committee; R. E. Hobart, mechanical superintendent, Lehigh Navigation Coal. Co., Committee on Visits and Inspections; H. D. Kynor, general manager, Northumberland Mining Co., Committee on Programs and Papers; B. H. Stockett, general manager, Weston; Dodson, Inc., Reception Committee.

Jan 1, 1932

All the TECHNICAL PUBLICATIONS and PREPRINTS published in 1932 are available at Institute headquarters. They are also on file in public,, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. Copies of the TECHNICAL PUBLICATIONS have been mailed to those members of the Institute who are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Institute of Metals Division; F-Coal Division;. G-Petroleum .Division; H-Nonmetallic Minerals; I-Mining Geology; K-Mining Administration; L-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Copies of PREPRINTS may also be obtained from the Secretary&apos;s office. Additional copies are sold at the rate of 1 cent per page; minimum charge, 25 cents. Nonmembers may purchase the papers at the prices mentioned. METAL MINING TECH- NICAL PUBLI- - TITLE AUTHOR MEETING TRANS. CATION VOLUME No. AND PAGE* 484-A.45 Propeller Type Mine Fan at Moose A. S. Richardson New York 102, 86, 93 F.52 Shaft, Butte, Montana (13) Feb., 1932 487-A.46 Progress in the Improvement of Max H. Barber New York, Methods and Equipment at Feb., 1932 Open-pit Iron Mines on the Lake Superior Iron Ranges (9) Pre. Sand Filling through Pipes and Lucien Eaton New York, 102, 33, 41 Boreholes (9) Feb., 1932

Jan 1, 1932

By Eugene McAuliffe

AS anthracite is no longer used to a marked extent by the rail- ways of the United States (1,513,000 tons in 1933), that portion of the mining industry engaged in the production of bituminous coal is, and will continue to be, the one chiefly concerned with the future use of its product by the railways. In a period such as the present, when all enter- prise is unsettled, when fundamental principles of industrial management and control are being swept aside or else changed overnight, it is difficult to predict what will happen. The relation between the total production of bituminous coal and the volume consumed by the steam rail- ways of the United States, Classes I,

Jan 1, 1936