Search Documents

By T King

This paper reviews the changes in the coal industry over the past 30 years and attempts to predict the trends over the next ten years. The last 30 years have seen a steady concentration of production into fewer, larger mines, which operate on 3: more continuous basis, and a major increase in productivity per employee. Coal exports have increased from zero to almost half the country's total production. As well as major changes in exploration and mining equipment and the increasing use of computer tools, the industry now operates in a relatively new regulatory and commercial environment.   Safety legislation now requires the writing and enforcement of policies and procedures by the mining companies, rather than adherence to inflexible regulations enforced by an Inspector. Accident rates have decreased dramatically. The transition from coal mining licences to permits, requiring landowner consent and resource consents, is well under way. Environmental controls are now an essential aspect of the industry.   Equipment suppliers now offer maintenance services, production guarantees and flexible financing.  Contract miners offer mine design and restoration as part of the contract. In a similar approach, Solid Energy now offer an ash disposal service and assistance with resource consents to their customers as well as investment in technology to ensure a consistent product to demanding specifications. Solid Energy has proposals for energy centres which install and operate the coal burning appliances and simply sell energy to the customers. The next 10 years should see an intensification of these trends of bigger mines, more exports and greater technology and a 'package' approach to customer service.

Jan 1, 1997

By N. Damiano, C. Zhou, B. Whisner, M. Reyes

"The Industrial Internet of Things (IIoT), a concept that combines sensor networks and control systems, has been employed in several industries to improve productivity and safety. U.S. National Institute for Occupational Safety and Health (NIOSH) researchers are investigating IIoT applications to identify the challenges of and potential solutions for transferring IIoT from other industries to the mining industry. Specifically, NIOSH has reviewed existing sensors and communications network systems used in U.S. underground coal mines to determine whether they are capable of supporting IIoT systems. The results show that about 40 percent of the installed post-accident communication systems as of 2014 require minimal or no modification to support IIoT applications. NIOSH researchers also developed an IIoT monitoring and control prototype system using low-cost microcontroller Wi-Fi boards to detect a door opening on a refuge alternative, activate fans located inside the Pittsburgh Experimental Mine and actuate an alarm beacon on the surface. The results of this feasibility study can be used to explore IIoT applications in underground coal mines based on existing communication and tracking infrastructure.IntroductionThe U.S. approach to health and safety in mining has historically been reactive in the sense that health and safety regulations and mandates have traditionally been passed as a result of tragic mining accidents. An example of this is the Mine Improvement and New Emergency Response Act (MINER Act) of 2006, which was passed as a result of several mining accidents where tracking of and communication with underground personnel were severely limited. While this reactive approach has led to the development and implementation of highly impactful safety interventions and safety practices, there exists a technological revolution that can shift the paradigm toward a proactive approach based on preventative methods: Internet of Things (IoT).IoT is the network of physical objects, or “things,” embedded with electronics, sensors and connectivity to enable that network to achieve greater value and service by exchanging data with the manufacturer, operator and/or other connected devices (Atzori, Iera and Morabito, 2010; Gubbi et al. 2013). It should be noted that IoT has been defined from various perspectives, and hence numerous definitions exist in the literature. The apparent ambiguity of the IoT definition might be due to the fact that IoT is syntactically composed of two terms: the Internet and things. The first word pushes toward a network-oriented vision, while the second tends to put the focus on generic objects. The traditional Internet can be viewed as an internet of computers, so things connected to the Internet are computers only. IoT extends the internet by allowing other generic things that are commonly found in daily life, such as refrigerators and cars, to be interconnected through the Internet, thus creating a bridge between the virtual world and the physical world"

Jan 12, 2017

By Clyde E. Williams

MODERN steelmaking has gradually evolved from an inefficient small-scale operation, utilizing tiny units, to a highly efficient one utilizing large units almost completely mechanized. The leading position of the United States in the steel industry is due to the possession of easily assembled high-grade raw materials and large-scale highly developed plants. Modern integrated steel operation is largely one of material handling. Mining and transportation of iron ore, coal, and fluxes, coking the coal in by-product ovens, smelting the ore with coke and limestone in blast furnaces, converting the resulting pig iron into steel in the Bessemer, or in the open hearth when supplemented with scrap, and fabricating the resulting steel ingots in the shapes of commerce all are done on a huge scale, mostly by machinery, most of the labor being employed either in operating the machine or keeping it in repair. At the same time the quality and uniformity of the product have been greatly increased by the development of scientific knowledge and operating skills. Thus, the steel industry in this country is highly developed both mechanically and technically.

Jan 1, 1942

By M. C. LAKE

THE industrial development of the United States has been stimulated by the presence of high-grade iron ore in the Lake Superior district. These great deposits have been susceptible to economical extraction and are conveniently located for cheap lake vessel transportation to the great consuming centers. The district furnishes from 80 to 85 per cent of the iron ore annually consumed in the United States, and a full understanding of the available supply of this great commodity is so important that it is well to consider whether or not the industrial supremacy and national independence attained as a result of the abundance of cheap ore are permanent. The enormous deposits of high-grade ore available in the Lake Superior district have been the foundation upon which the vast industrial structure of the steel and allied industries has been built. It is extremely important to the country as a whole, and especially to those States and communities now dependent on Lake Superior ore for their prosperity, that their industries shall retain the particular advantages with which they are now endowed, and that a generous supply of high-grade raw material be available for their consumption at a satisfactory cost. The steel industry is so basic and fundamental that any fluctuation in the cost of its finished products as determined by the supply and cost of the raw materials involved in its manufacture will necessarily affect the business of a wide variety of industries which are dependent on it.

Jan 1, 1926

By J K. Irwin

The authors discuss the application of drum and friction hoists under modern conditions and give four examples of friction hoists proposed for various applications. The paper concludes with a summary of the advantages and limitations of friction hoists relative to drum hoists. Introduction T H~ introduction of the multiple-rope friction hoist m the late 1940's has complicated the se-lection of the right hoist for a given job. Once such considerations as rope safety factor, drum to rope ratio, hoisting distance, tons per hour and/or service duty have been decided upon, the selection of a drum hoist is relatively simple. We now ask our-selves "which hoist -drum or friction? (See Figure 1 and Figure 2). When a friction hoist is a possibility we are immediately concerned with how many ropes to use, whether to hoist balanced or counter-balanced, whether a friction hoist will be flexible enough for the application and, of course, what the relative costs will be.

Jan 1, 1964

By C Harwood, EáWestman, K Luxbacher

Testing of in situ seals in underground coal mines is critical to determine seal integrity and to provide safe working conditions. In the wake of the 2006 Sago Mine explosion, the United States of America (USA) promulgated the Mine Improvement and New Emergency Response (MINER) Act (USDOL, 2006) which required mines to install 827 kPa (120 psi) rated seals or monitor and maintain the atmosphere behind existing 345 kPa (50 psi) seals. The purpose of developing the regulations was to prevent the breaching of seals in the event of an explosion in the sealed area.While seal design and construction is carefully regulated in practice, the construction of seals is difficult to monitor, as many are constructed under various mine conditions and the methods rely on prescribed placement of the seal material. Further examination of installed seals is limited to two-dimensional visual inspection and atmospheric and convergence measuring devices. These methods do not accurately reflect the integrity of the seal and cannot detect changes, deterioration, or defects within the seal.If detection of defects, deterioration and damage is not possible, unexpected communication between the active and sealed areas may result. Additionally, the ability of the seal to withstand explosions may be compromised. Non-destructive testing (NDT) of underground mine seals is necessary to investigate if the seal properties have been altered and if the seal remains functional as a barrier between active areas and sealed areas of the mine. This paper gives a preliminary assessment of proposed NDT methods for seal evaluation using radio frequency (RF) technologies and tracer gas methods.CITATION:Harwood, C, Luxbacher, K and Westman, E, 2013. Non-destructive testing of in situ underground mine seals - Initial technology assessment, in Proceedings The Australian Mine Ventilation Conference , pp 299-306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Henk van der Bijl, Sean Rogers, Eugene Sidorski, Alan Carpenter

The electrode column is the heart of the submerged arc furnace. Superior electrode performance provides improved furnace performance. This paper describes the main features of the electrode column that delivers superior performance in furnaces worldwide, developed by Pyromet. Pyromet?s electrode comprises the compact slipping device, lower electrode assembly, upper and lower mantles, self-adjusting electrode seal, paste heaters, and Pyromet?s patented innovative electrode breakage detection and length determination system. Pyromet?s slipping device features compact interlocking clamping rings, incorporating fail-safe spring-loaded design. The interlocked clamping rings distribute the clamping force over a larger area of the electrode casing, preventing damage. The slipping device assembly features a low maintenance modular design that allows rapid slipping cycle times, back slipping, and compatibility with Pyromet?s electrode breakage detection and length determination system. Pyromet?s lower electrode assembly consists of the contact shoes, pressure bellows, pressure ring and heat shields. The contact shoes and pressure ring are designed for long, trouble free operation whilst the pressure bellow configuration equalise contact pressure and current distribution. Furthermore, the contact shoes incorporate a self cleaning feature, ensuring optimum electrical contact. The segmented design offers easy maintenance. Pyromet?s clients experience less down time due to longer component life. Pyromet?s remote adjusted electrode seal assembly reduces the rope seal working temperature, increasing rope life. The self compensating rope seal clamping force ensures an effective seal as the rope wears. Pyromet?s electrode breakage detection and length determination system detects electrode breaks utilising Pyromet?s electrode holder and data processing system. The length measurement system controls electrode length, eliminating the occurrence of short electrodes. The length measurement system furthermore eliminates the need for manual electrode length measurement, reducing associated production losses during furnace burn downs.

Jan 1, 2007

By Li Zhang, Jing Zhao, Chuanwei Zang, Shuanlin Wang

The application of gob-side entry retaining (GER) in steeply pitching seam longwall mining with a hard roof has always been a difficult problem. Based on the simplified roof beam mechanical model, the traditional gob-side entry retaining by packing (GERP) roof structure evolution process and its problems with use in steeply pitching seams are analyzed. Therefore, based on the unique characteristics of the gangue rolling and accumulating in the steeply pitching seam, this contribution proposes an innovative method of gob-side entry retaining by roof cutting (GERRC) in steeply pitching seam and details its technical process. The roof structures of the GERRC and the GERP are compared. Taking the Chang Gouyu Coal Mine as a case study, field experiments were carried out. This research finds that the GERRC can both overcome the impact of rolling gangue on roadside support and make the rolling and stacking gangue become a roadside support. The roof structure of the GERRC is in a one-time statically indeterminate state, which is conducive to the stability of the roadway. In the field test, the total displacement of the roadway roof and floor is 97 mm, the supporting pressure of the serried single props is less than 28 MPa, and the props have no obvious bending phenomenon.

May 6, 2020

By M. R. Hieb, J. R. Britt, S. P. Harteis, M. J. Sapko, E. S. Weiss, R. K. Zipf

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations), even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of possible explosion pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners’ Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic and safe mine sealing technique that can enable mine seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble, in combination with a conventional mine seal, so that the pressure resulting from a gas explosion is reflected, absorbed and attenuated, and the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a “passive mine blast attenuator” (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals.

Jan 1, 2009

By Demetrius Da Rós Ruy

O lingotamento contínuo é uma das etapas mais importantes na produção de aço, sendo um método rápido e eficiente na fabricação de placas ou tarugos através de processos de resfriamento onde o aço líquido é moldado e solidificado. Contudo, têm sido historicamente observado problemas de processo corrosivo acentuado na câmara de exaustão e na estrutura das máquinas da ArcelorMittal Tubarão. Os mecanismos deste processo corrosivo em máquinas de lingotamento contínuo, em geral, são variados e diretamente relacionados às condições operacionais da máquina, conduzindo a elevados custos de manutenção, diminuição da vida útil das máquinas, causando insegurança e interferindo na qualidade do produto. Este trabalho objetiva descrever as causas principais deste processo corrosivo e mostrar o desenvolvimento de testes que foram conduzidos visando a minimização deste fenômeno na máquina de lingotamento de placas #1 da ArcelorMittal Tubarão no ano de 2017.

Oct 30, 2017

Electricity will play a major part in providing energy services in the 21st century. Ecologically Sustainable Development (ESD), that is accommodating the needs of the present without compromising the needs of future generations, will provide a focus for optimising the use of electrical energy. Environmental externalities may redefine the cost structure of electricity. Strong corporate environmental management will ensure that current environmental objectives are met and that future ones, identified by the ESD process and environmental externalities accounting, can be developed and implemented by receptive business managers. This paper addresses the current environmental issues of electricity production. It outlines a management strategy for the SECV becoming a community leader in protecting the environment. ESD is discussed in terms of using non-renewable resources wisely, extending their availability and putting in place mechanisms which ensure their ultimate substitution by renewable resources and conservation. The paper explores options for dealing with costing environmental externalities, particularly in relation to greenhouse emissions.

Jan 1, 1992

By R. S. Douglas

Introduction During the past few years, a number of changes in the mine operations at Copper Mountain have taken place. The modernization and mechanization were necessitated and given impetus by wartime and other conditions, which were: (1) The urgent need for copper for wartime purposes. (2) The scarcity of skilled labour for underground work. (3) The increase in labour and supplies cost. (4) The necessity of finding ways and means of increasing the output per man-shift, because of the scarcity of skilled labour and the rising cost of labour. (5) The desire to increase safety measures, reduce the silicosis hazard, and aid mine ventilation. (6) The desire to improve the general working conditions in the mine for all workmen. (7) The desire to reduce the amount of dilution in the ore stream by a more selective yet highly productive method of mining. To this end, mining with diamond drills, and transferring broken ore with slusher hoists, appeared to be the answer to the problem. After considerable discussion and estimation of costs for comparison with those of the operation as carried on at that time, the proposed methods were tried out and, in practice, gave very gratifying results. Reference at this point is made to the paper written by C. H. Brehaut, W. N. Taylor, H. A. Shannon, and R. S. Douglas, which was published in the September, 1945, issue of Mining Technology, by the American Institute of Mining and Metallurgical Engineers, Inc., and subsequently in commercial mining journals. Since that time some improvements have been made in undercutting an orebody - the first through experiment and practice, the second through making use of the earth's barodynamic or gravitational forces. It is the purpose of this paper to describe and discuss these later developments.

Jan 1, 1947

By Will H. Coghill, Fred D. DeVaney, R. S. Dean

Part I CONTENTS

May 1, 1934

By RUSSELL C. FLEMING

THE important advances that have been made of recent years in mining and milling methods and in mechanical equipment at mines need no re- telling, but there has been a remarkable growth in one type of equipment which has gone nearly unnoticed. That is the increasing use of storage-battery locomotives underground. Since the war the number of these locomotives and their field of use have increased tremendously; their growing acceptance represents an al- most complete reversal of opinion from an earlier period when they were generally looked upon as in- adequate for the strain of mine service. At the time when storage-battery powered units were first making their bid for recognition, the use of power in haulage had already passed through several phases; hand tramming, rope haulage, compressed air locomotives, even gasoline locomotives, had all been used, ending finally in the general adoption of the electric trolley locomotive for practically all power-haulage requirements. It was, and is, conceded that the trolley loco- motive met more adequately the varied and severe conditions of mine service than any previous type of haul- age unit. Subsequent developments have had to endure comparison and surpass in performance that type of haulage before changes would be considered.

Jan 1, 1930

By F. Boudreault, M. J. Scobie, J. Szymanski, C. Hendricks

The development of new stoping methods and more effective control over dilution, recovery and fragmentation depends on improved accuracy in blasthole drilling. The mechanisms and factors which control accuracy are poorly understood. Canadian blasthole stoping and the practices adopted for monitoring and controlling drilling accuracy are reviewed. The techniques and problems associated with blashole set-up and trajectory surveying are discussed. Four new blasthole trajectory survey systems are evaluated on the basis of their performance in recent underground trials. Conclusions are drawn as to the technological developments required so that more precise control over drilling accuracy can be achieved.

Jan 12, 1992

By J. C. White

This paper, after a brief introduction giving the history and geology of the area, deals with mining operations at the Copper Mountain mine of Gaspe Copper Mines, Limited. It discusses development operations, and then goes into the mining methods employed, covering drilling, grade control, blasting practice, loading and hauling, and the road and service machines used.

Jan 1, 1969

By Richard A. Walker

This report describes the development and performance of a multi-level, multi-function Calibration Light Source designed for field-calibration of a group of specific photometers. The Calibration Source is capable of providing ±35% accuracy calibrations at all of the following levels: 0. 05 foot-Lamberts, 6 foot-Lamberts, 6 foot-candles and 20 foot-candles. The Source was found to provide constant light output to within 1% over 50 hours of lamp operation and for line voltage variations of ±25%. It is compact and light-weight (11 pounds), and can be easily transported and used by one man in normal office environments (without requiring a darkroom).

Jan 1, 1976

By Philip Morey

Large scale surface coal mining will be required to fill future energy demand in the United States. In realization of this long-term commitment to coal resources, the U.S. Energy Re-search and Development Administration sponsored a study to determine the costs and problems of large-scale surface coal mining. As a result of this study a series of computer models were developed that can be used by government and industry to: 1) facilitate mine design and equipment selection, 2) provide detailed analyses of mining and processing costs. Two types of models were developed: detailed simulation models, which provide detailed information on mining systems and equipment to assist in mine design and equipment selection1 and broad models, which provide a first-order evaluation of deposits and new ventures for an entire mining complex. The complete model series permits examination of surface coal mining under a variety of terrain conditions. Six different mining methods were analyzed and documented during the overall project: 1) Area stripping with draglines, 2) Area stripping with draglines, extended bench, 3) Contour stripping with draglines, 4) Area stripping with shovels (loaders) and trucks, 5) Mountain top removal with shovels (loaders) and trucks, 6) Multiple dipping seam mining with shovels (loaders) and trucks. Each major operation in the coal mining pro-cess is represented in these models so that the best methods and equipment may be selected and 50 that the impact of such selection will be reflected in estimates of capital investment, operating costs, and coal price. Individual models allow the user to separately analyze overburden removal, overburden drilling and blasting, coal drilling and blasting, coal loading and hauling, coal preparation and handling, land reclamation, and premining, facilities, and administrative expenses. Because it is impossible to cover all the models in this paper, only the detailed simulation models representative of the technique "area stripping with draglines," are described. The Fort Union Strippable Coal Resource Region, one of eight test cases, is used as an example to describe the models.

Jan 1, 1978

By H. M. Lewis

The current status of the international zinc market is summarized, and a supply /demand outlook is presented for the next five years. A number of technical problems facing the industry are outlined. Introduction ZINC has sometimes been called the unknown metal. Considering that on a world basis it ranks third among non-ferrous metals in production and consumption, zinc retains a certain modesty. It has no distinctive colour like copper, lacks the low density of aluminum or magnesium and is not always easy to identify as a product. The 'spangle' of galvanized steel is probably zinc's most distinguishing feature. The purpose of this article is to develop an over-all review of zinc. Starting with the current position of the metal, the major factors that will shape its future will be described so that an assessment of the outlook for zinc can be made.

Jan 1, 1978

By G. De Gregoriis, G. E. da Mota, H. P. Dias, J. E. M. Blasques

In recent years, like many other smelters around the world, Albras has been increasing line current. The necessary adjustments to the work practices and process variables need to be made on all potlines, which in this case means on 960 cells at the same time. It was a challenging task to adjust the process parameters to the new amperage. In July 2003 potlines 2, 3 and 4 were running at 1 73 kA and the goal at that time was to reach 180 kA. Preliminary trials with 180 kA were performed on a group of 10 boosted cells on potline 3 in order to investigate possible operational problems. It was decided to increase the amperage in three steps accompanied by continual evaluation of the state of the process. In July 2004 the target of 180 kA was achieved with good operational results. This paper presents the overall results, the parameter adjustments made during the amperage increase in the booster group and how the increase was implemented on the other potlines.

Jan 1, 2006