Search Documents

By S. Ozbilen

"Al-Li binary alloys with nominal Li contents of0.15, 1.1and2.8 (in wt%) were aged naturally at room temperature for two months, aged at low temperatures ( 65 and 1 OOEC) for up to 2 months and aged artificially at 190EC for 4 days after water quenching to 25EC following solutionizing at 530EC for 20 minutes. Ageing behavior of these binary alloys were studied by Vicker's Hardness measurements and DSC thermal analysis. Thermal analysis results indicate the formation of GP zones of Al-Li system in Al-2.8wt%Li binary alloy. In the same alloy, rapid quenching from one phase region (a) gives rise to precipitation of small o' particles in a matrix (a) with still high supersaturation. During ageing of this alloy below lOOEC an additional transformation, i.e., GP zone formation occurs proceeding at a very high rate which is described on the basis of the theoretical analysis for the quenched Al-Li system proposed by Khachaturyan et al [6]. Ageing at temperatures below 11 OEC takes place slowly by the formation of small d' particles of lower thermal stability than the quenched-in d precipitates in addition to GP zones resulting in an increase in hardness compared to water quenched samples. During artificial ageing, GP zones transform by dissolution to d' precipitates while d' particles already in the microstructure coarsen during under aged condition at which hardness increases with time till peak aged condition.IntroductionIn binary Al-Li alloys the d' (Al3Li) fully coherent internally ordered inetastable phase of Li2 structure with a=0.4038d [1-5] forms homogeneously between 120 and 190EC before the formation of stable d' (A!Li) phase and cause the superior mechanical properties. This is due to an appreciable age hardening effect resulting because of the d' precipitation during ageing [1]. The response of d' to decomposition and its formation kinetics have been studied previously and it is believed that the decomposition of the a-supersaturated solid solution occurs in a two stage process; i.e., a 6 d' (Al3Li) 6 d(A!Li). Khachturyan et al [6] theoretically investigated precipitation of the d' phase and gave an interpretation of the transformation paths of the quenched Al-Li alloys. They predict that the disordered supersaturated solid solution congruently orders, and then the uniformly ordered solution decomposes into ordered regions that differ in Li-content. Finally, ordered d' phase forms in the disordered matrix."

Jan 1, 1998

By Joseph Sofra

It has become increasingly evident that sustainable metals production in the 21st century requires producers to balance the needs of cost effective, high value production with that of responsible plant operation. This is becoming more difficult as lower grade and more complex feed materials, including recycled scrap and residues, are being processed to reduce production costs and decrease exposure to primary metal market fluctuations. One particular facet of the metals industry facing these challenges in the 21st century are copper producers, The recent steady decline in the copper price has seen the industry cut expenditure, tighten control on income streams and focus on high returns on capital investment. For these reasons copper producers are looking towards flexible technologies that can deliver high value products, with minimal environmental impact at low capital and low sustainable operating costs. Ausmelt's Top Submerged Lancing (TSL) technology for copper production is a low cost, proven technology for the processing of both primary and secondary copper materials. Both the smelting and converting operations introduce significant advantages in environmental performance, improved process efficiencies and high rates of metal recovery, Ausmelt has made significant gains in the past 4 years in establishing a strong market position for its copper technology, New installations in China, South Africa and India as well as existing operations in Zimbabwe and China have demonstrated its effectiveness. This paper reviews the application of Ausmelt Technology for both smelting and converting of primary and secondary sources, It discusses Ausmelt's design and implementation philosophy, and how this philosophy meshes with the needs of the end user.

Jan 1, 2003

By P. Tim Johnson

Relentless increases in demand for nickel and vanadium for uses such as steelmaking, catalysts and battery materials, plus the growing financial and environmental costs of their primary extraction, have led to much interest in potential secondary sources of these metals. The presence of such metals in heavy fuel oils, bitumen and related materials offers both opportunities and challenges for potential extraction methods, especially with the growing production and importance of metal-rich fossil fuels around the world. For several decades, Tetronics’ DC plasma smelting technology has been used for the recovery of metals such as nickel and chromium from stainless steel melt dusts and other wastes in compact, environmentally-friendly and efficient plants. This paper explores the suitability of DC plasma smelting as part of a wider flowsheet with feed preparation and aluminothermic reduction techniques for smaller-scale extraction operations based on this important niche secondary source of these key metals.

By K. J. Murphy, A. R. Smith, A. P. Odorski

"The need for large quantities of oxygen for use in metallurgical processes was a major driving force in the commercialization of tonnage air separation plants. Oxygen, nitrogen and argon impact the quality, energy efficiency and environmental aspects of metals production. Cryogenic air separation processes have been used to supply most industrial requirements, however, newer technologies are available or under development to meet the needs of today's and tomorrow's metallurgical processes. This paper reviews the technical features and state of development of adsorption, chemical, cryogenic and membrane technologies. The technologies are compared in terms of plant size, oxygen purity and pressure, nitrogen and argon co-production, product use pattern and back-up requirements. Computer control systems are described that optimize operation over varying load patterns and ambient conditions; substantially lowering energy consumption. IntroductionOxygen production totalled 390 billion cubic feet in 1987. Although current production is lower than the peak of 455 billion cubic feet reached in 1979, oxygen remains the fifth leading chemical product manufactured in the u.s. (1) Metals manufacturing and fabrication accounts for sixty percent of the oxygen consumed in the u.s. Oxygen use in the steel industry consists of air enrichment for conversion of iron ore, purification of the iron in basic oxygen or other furnaces, and for cutting and welding the finished steel product. Nonferrous ores are smelted in oxygen enriched atmospheres to reduce energy consumption and increase capture of sulfur compounds to meet environmental requirements. In the future oxygen usage is expected to become even more important in metals production as energy costs increase, environmental standards become more stringent, and as new coal based processes become commercialized. Oxygen usage per ton of metal in the new direct reduction processes can be up to ten times higher than traditional steel making."

Jan 1, 1988

By Roger C. Urquhart

Copper-nickel-sulphide ores mined in the Rustenburg district of South Africa are generally smelted in electric furnaces because of the high-temperature slag produced, the availability of cheap electric power, and the smaller pollution problems. Apart from melting, the functions of the electric furnace are to recover most of the matte content in the converter slag by physical and chemical interaction with the furnace bath and to provide adequate time for the optimum separation of matte and slag. Smooth, efficient operation will denend on fluid slags for settling, balanced by high resistivities to obtain adequate concentration and distribution of power by way of current heating. To obtain a greater understanding of the processes involved, an investigation was undertaken at Rustenburg Platinum Mines on the smelting of copper-nickel concentrates in a 19.5 MVA furnace with six in-line electrodes. The matte- and slag-tapping temperatures, slag temperatures, slag analyses, electrical data, and electrode position were measured. Radioactive tracers were introduced into the slag, and quantitative results relating to the flow pattern within the furnace were obtained. These studies were augmented by scaled laboratory investigations relating to the determination of cell constants and current distribution within the furnace. Instantaneous field and power distribution plots were determined by use of an on-line mini-computer. The applicability of these results to furnace operation is discussed.

Jan 1, 1976

By Jing Lin, Yuan Xu, Qingcai Liu, Dengfu Cheng

"Smelting reduction technology has been developed greatly in recent years. But one of the key problems for this technology is about the refractory that used as lining material in the molten bath. Investigation and test shown that corrosion rate of refractory was much higher and the corrosion mechanism was much more complexity in the molten bath of smelting reduction with iron bath than that of the blast furnace and rotary furnace technology [l-5]. The corrosion behavior and corrosion rate of Al2OrC-ZrO2 series refractory in the melt of smelting reduction with iron bath have been studied by rotary immersion and quasi-static immersion test in this paper. The major factors that affect the interaction between the melt and refractory were investigated. The test results shown that the corrosion rate of AI2O 3-C-ZrO2 series refractory decreased with the ZrO2 increasing when ZrO2 content was from 3% to 10%. Ferrous oxides content, relative moving speed between the melt and refractory and temperature of the molten bath were the important factors that affect the corrosion rate. But the ferrous oxides concentration was the most important one. The corrosion rate was increased as a linear relation with the rising of ferrous oxides content of the melt. The corrosion rate in the quasi-static immersion was much less than that of the dynamic immersion (rotary immersion) for the Al2O 3-CZrO2 series refractory in the same testing condition. The corrosion mechanism of Al2OrC-ZrO2 series refractory is: graphite oxidized in advance, then interaction between the constituents of refractory and melt taken place and deteriorate layer of refractory and new compounds were formed, the properties of refractory was changed.IntroductionSmelting reduction with iron bath is a typical technology [3, 4, 6]. The obvious features of the melt for smelting reduction technology with iron bath are much higher ferrous oxides and much more complexity melt composition and structure than that of the blast furnace technology [2, 5-8]. The properties of the melt were changed dynamicilly and constantly in reduction process. On the other hand, the behavior of the melt depends on the activity and the reduction rate of ferrous oxides in the molten bath[9]. Because of the high concentration of ferrous oxides in slag and high reduction rate in the molten bath, the corrosion behavior and corrosion mechanism of the refractory lining by melt are an important factor in development of the technology of smelting reduction with iron bath. Up to now, improving refractory quality to anti-corrosion of melt and developing high quality and long term refractory used as the lining refractory materials in the molten bath of the final reduction furnace are also the most important questions for developing smelting reduction technology."

Jan 1, 2000

By Jian Yang

The mechanism of resulfurization in the desulfurization process with magnesium vapor produced in situ by aluminothermic reduction of magnesium oxide was clarified in the present work. The influences of various operating parameters on the resulfurization were studied and the methods that could prevent resulfurization were proposed. There are two kinds of mechanisms of resulfurization in the desulfurization process with magnesium. One is decomposition of the desulfurization product of MgS under the inert atmosphere. The other is oxidation of MgS under the oxidative atmosphere. Under the present experimental conditions, lowering operating temperature and oxygen partial pressure in the atmosphere could effectively prevent the resulfurization. Adding CaO onto the melt surface was an effective method for preventing the resulfurization due to transformation of the desulfurization product of MgS into the more stable compound of CaS. Since addition of the activated charcoal powders greatly decreased the transfer rate of oxygen in the atmosphere to the melt surface, it also reduced the resulfurization remarkably.

Jan 1, 2006

By C. Ek

In bismuth metallurgy, low-copper high-sodium mattes are by-produced. Different charges containing mixtures- of crude mattes, oxidized matte, and/or copper sulfide concentrate and/or copper silicate ore have been smelted to give a rich matte and a disposable slag, then converted to obtain blister copper with high recovery and a rich slag to be recycled.

Jan 1, 1983

By R. H. Hanewald

INMETCO, a subsidiary of Inco Limited, is the only facility in North America that provides High Temperature Metals Recovery for nickel-, chromium-, and iron-bearing wastes. Since 1978, this process has prevented more than 775,000 tons of materials from becoming part of the nation's waste stream. The paper describes Inco's experience in metals recovery, traces the development and explains the operation of the High Temperature Metals Recovery Process, and examines the procedures and criteria used to determine whether spent catalysts meet process feed specifications. An overview of the current requirements for transporting spent catalysts is provided. The paper concludes with brief case histories of catalysts users employing High Temperature Recovery to manage spent catalyst.

Jan 1, 1995

By Jeffrey L. Zelms

Environmental issues and how they are addressed -- or not addressed -- by the lead industry in the 1990s will determine the eventual fate of lead mining in both the U.S. and worldwide. Clearly, governmental regulation throughout the West will become harsher. Equally clearly, the industry has? failed to educate the public regarding lead. Instead of public support for a critical mineral, we face widespread public ignorance and paranoia. If we can demonstrate the public interest benefits of the industry, the 1990s will be a decade of continuing growth -- not dynamic growth, certainly, but growth at least comparable to the world economy. If, however, we fail to demonstrate the industry's public interest benefits, the 1990s could mark the beginning of the end of our business.

Jan 1, 1990

By Gernot Schenker

With the shut-down in the mid-1970s of the last shaft furnaces in the Harz Smelter Plant the long tradition of the Primary Lead Smelter in Oker came to an end. A continuation of the concern was nevertheless possible as a result of the timely commencement with the development and construction of lead production from secondary raw materials. Then as today, the most essential secondary raw material is lead accumulator scrap with over 80 % of the raw material pallet. Already in the 1960?s a method of reclamation lead battery scrap was developed and successfully carr.ied out by Preussag. In 1983 this process was fundamentally modified, also for environmental protection reasons within the framework of a rehabilitation programme of the existing plant. Today Metaleurop's HarzMetall GmbH in Oker is equipped with a modern secondary lead smelter which includes all environmental protection installations required by law. Besides processing battery scrap, the. smelter is in a position to process a ?multitude of other lead bearing residues in an economically useful way, whose waste disposal would otherwise be impossible due to the ever-increasing environmental protection laws or only be achieved at great expense.

Jan 1, 1990

By Dolf Gielen

This paper discusses the results of a Western European energy and materials systems engineering study that analyses the impact of greenhouse gas (GHG) emission reduction on the future of the steel and aluminum industry. he technology selection will be significantly affected by future CO2 policies. The avail- ability of C02 removal and storage technology and the social acceptance of this strategy for GHG emission reduction is of key importance for the strategy selection. The use of coal based smelting reduction technologies is optimal in case of weak C02 policies or in case of strong C02 policies and low CO2 removal and storage costs. The selection of CCF or Corex technology depends on the penalty regime. However, if C02 removal proves to be problematic, CCF development fails and strong C02 policies are introduced, the gas based DRI production processes will become more attractive. In both cases, the energy efficiency of the iron and steel industry will further increase in the next decades. The impact of GHG emission reduction on aluminum prices and aluminum use can be significant. However contrary to common notions the aluminum production will be positively affected by GHG emission reduction, notwithstanding the currently high emissions in aluminum production. A combination of emission mitigation in production and significant GHG emission reduction effects further down the product chain cause this effect. A significant potential exists for improved materials efficiency. This potential is generally neglected in energy efficiency and CO2 reduction studies. However improved steel qualities are of similar importance for C02 emission reduction as increased energy efficiency. It remains to see if this potential will be used to its full extent in the next decades. Model calculations indicate that the impact of C02 policies on the competition with other materials will be limited. Greenhouse gas emission mitigation will have much more impact on materials production and waste handling than on materials consumption.

Jan 1, 1999

By V. Ramachandran

Under the Resource Conservation and Recovery ACT (RCRA), generators of listed or characteristic hazardous wastes must find satisfactory means for disposal. of wastes. Initially, for many this meant landfills and deep-well injection. Until recently, mining and metallurgical by-products have largely been exempt from RCRA, but now are coming under its jurisdiction. With the increasing closures of landfills, companies in the U.S. such as electroplaters, miners, metallurgical plants and others are turning to recycling as an alternative to treat their wastes. While the cost of recycling has been challenging, the long-term economics prove attractive because recycling interrupts the cradle- to-grave responsibility for the waste generator. The present paper describes the recycling of hazardous wastes at ENCYCLE/TEXAS. Encycle extracts marketable metals from metal-bearing sludges and wastewater using hydrometallurgical processes borrowed from the mining and metallurgical industry.

Jan 1, 1994

By A. Mejias, M. A. Garcia, G. Diaz

During 1997 and 1998 two successful zinc feasibility studies, Skorpion and Sanyati, were carried out by Tecnicas Reunidas based on the modified ZINCEX® technology. The technical viability of each project was proved during more than 600 h of continuous running in a pilot plant. The Skorpion zinc project would recover 150,000 t SHG Zn/y from an oxidized zinc ore of a Namibian mine. The economical study showed that the plant would have the lowest production costs in the world. The Sanyati zinc project would treat a bleed from an existing copper refinery in Zimbabwe to recover 5,000 t SHG Zn/y. In the first case the electrowinning cellhouse was supplied by Union Miniere and in the second by Tecnicas Reunidas. This article highlights the pilot plant results and the advantages of the proposed process over conventional zinc production practices.

Jan 1, 2000

Two pilot-plant investigations were conducted in which strong-base resins were compared with activated carbon for the extraction of gold cyanide from leached pulp from the Golden Jubilee Mine. The results show that gold can be recovered with carbon, but that the extraction efficiency is poor, probably because high concentrations of humic and fulvic acids are. present m the pulp. .However the extraction of gold cyamde from this material with strong-base resins JS very effo:1ent, and the overall efficiency of extraction is better with resin than with carbon, even when the concentration of resin is one-third that of carbon, and the flowrate of resin is one-third that of carbon. The results of the pilot-plant campaign reported in this paper led to the conversion of the Golden Jubilee plant from carbon-in-pulp to resin-in-pulp in February 1988.

Jan 1, 1989

By Neeraj Saxena, Madhu Huggahalli, Jerry Bednarski, Ken Grieshaber, David Stoffel

"The use of oxy-fuel burners in secondary aluminum melting applications offers several advantages over air-fuel burners including reduced fuel consumption, faster charge to tap times and lower NOx emissions. Their successful, safe and economical use in a furnace depends on several factors and considerations such as burner and flue placement, metal circulation, charge practices and the type of refractory used in the furnace.These factors required in the successful conversion of furnaces from air-fuel to oxy-fuel based burners are discussed in this paper. Critical parameters are identified and examined using computational fluid dynamics (CFD) simulations. Parameters are estimated via laboratory testing and validated through trials performed at commercial installations. Guidelines and a simplified approach to estimate a priori the economic impact of converting from air-fuel to oxy-fuel are presentedThe final products of this research are simplified and validated tools for modeling aluminum furnaces. These include improved heat and energy balance models and parameterized CFD solutions which provide rapid customization to individual furnace configurations. These tools provide field engineers with immediate and accurate predictions of performance, allowing for repeated precise scenario analyses."

Jan 1, 2001

By Tiebao Yang

In high pressure die casting processes, a die plays a critical role in removing heat from the molten metal during the cavity filling and solidification stages. Proper control of die temperature is essential for producing superior quality components and yielding high production rates. This paper proposes a local temperature control scheme for die thermal management based on a computerized intelligent real-time monitoring and control system (IRMCS). In this scheme, cooling water lines are controlled by a pump and solenoid valves. A controller is designed according to the law of die temperature fluctuations. The results obtained from the experiments carried out on a laboratory die casting process simulator indicate that the controller can limit the local die insert temperatures in a given band. Hence, the desired thermal pattern of the die insert becomes achievable.

Jan 1, 2006

By Elli Nurminen

In this work the thermodynamics of the metallic sulphate decomposition reactions were studied through thermodynamical calculations and thermogravimetric methods. The decomposition temperatures and mechanisms were determined for cupric sulphate, ferric sulphate and also for industrial flue dust from a copper flash smelting process. The aim was to determine the thermodynamic conditions for sulphate decomposition and to estimate whether the reactions are kinetically likely to take place in the flash smelting process heat recovery equipment. The information is essential in CFD-modelling of the reactions taking place in the boiler and for optimising the process.

Jan 1, 2006

By J. R. Donald

For processing copper, continuous converting has been successfully employed in a variety of locations, but for nickel, there has yet to be a successful commercial implementation of continuous converting technology. At Inco?s Copper Cliff smelter, there are specific requirements for the production of Bessemer matte relating to downstream processing that makes continuous converting for nickel mattes even more challenging. The nickel carbonyl refineries require very low iron levels in the matte, and the sulphur deficiency must be carefully controlled such that the appropriate quantity of PGM-rich metallics are produced from matte separation. The present paper outlines continuous converter technologies that have been implemented in copper, and evaluates their potential for nickel converting. The challenges of producing a Bessemer matte to the required specifications are discussed. The economic and environmental driving forces, and the challenges of justifying a novel technology in place of productive existing equipment, are discussed.

Jan 1, 2005

By Mark R. Jolly, Jean-Christophe Gebelin, Aleksander Cendrowicz

"Injection of wax patterns is the first stage of the multi-stage process of investment casting. The quality of the final casting and its dimensional accuracy is highly dependent on this stage of the process. Pattern waxes used in the industry behave in a complex visco-elastic-plastic manner. The modelling of such material behaviour is therefore not simple.In this paper a number of configurations of die will be shown in which the injection of the wax has been carried out for a range of processing conditions. Some of the dies are transparent and the movements of wax front observed can be compared with those predicted by simulation. Surface defects in final components will also be shown and compared with the location predicted by simulation software. Some discussion will be presented on the limitations of the software used and the time-scales achieved for practical use as a design tool within the foundry environment. IntroductionThis paper presents the research activities carried out at the University of Birmingham on the modelling and prediction of the behaviour of industrial investment casting waxes during the injection of wax patterns. These research activities are done in the context of a more global study of the fundamental aspects of the investment casting process, the FOCAST project. Regarding the wax injection process, the aim of the project is to achieve a better understanding of the key factors that will lead to better castings. The filling of the die during the injection has been studied. Some other phenomena such as shrinkage/warpage or creep under residual stresses are also studied, but not presented here. Two commercial investment casting waxes have been characterised in order to model their behaviour and predict mould filling and subsequent defects.This paper will present the models that have been used in our work, the simulation packages used, the experiments carried out to validate the modelling and exhibit the defects due to bad filling, and finally the numerical simulation results."

Jan 1, 2001