Search Documents

By S. H. Amini

The effects of CaF2 and ilmenite on dissolution rate and diffusivity of CaO in calcium alumino-silicate based slag in a temperature range of 1500 ? 1600 ºC were studied by using the rotating disk/cylinder technique. The effect of rotation speed on the rate of dissolution in the base slag indicated that mass transfer in liquid slag played a significant role in controlling the dissolution. At a constant rotation speed, the effect of 5 wt% addition of fluxes tothe slag on the dissolution rate was investigated at various temperatures. While CaF2 had the highest effect, addition of ilmenite increased the rate of dissolution significantly. The diffusivity of lime in these slags was quantified using the dimensionless mass transfer correlations for rotating disk/cylinder in the melt. The diffusivity values were deduced using the data on dissolution rate and solubility of lime in the slags. The measured diffusivity in base slag at 1500 C was found to be about 1.32 10-5 cm2/s and increased to 3.07 10-5 cm2/s at 1600 °C. Addition of 5wt% CaF2 increased the diffusivity by a factor of 3 to 5, while 5wt% ilmenite increased the diffusivity by a factor of 2 to 3 in the temperature range of 1500 to 1600 ºC. The two examined fluxes reduced the activation energy of diffusion.

Jan 1, 2006

By Brady Butler

Many high capacity metal hydrides exhibit a high degree of stability in the hydrogenated state. This stability leads to a number of significant design problems with regard to the low temperature kinetics and thermodynamics of dehydrogenation. Nanometric metal hydride materials provide a promising route for increasing the reaction kinetics while altering the thermodynamic stability of the material. The use of nanometric metal hydride materials for hydrogen storage has largely been absent because of the difficulties associated with the synthesis of these materials. In this paper, research results on the synthesis of lithium based metal hydrides by vapor phase reactions are presented. The lithium based compounds that have been made in our lab include nanosized powders of metallic Li, Li₃N, LiNH₂ and LiH. The vapor phase process has also been used to custom engineer Li-based materials with other alloying elements or doping elements. The dependence of the characteristics of these materials on synthesis process parameters is studied. The effects of nanoscaled particle sizes on the kinetics of dehydrogenation and hydrogenation reactions are also explored.

Jan 1, 2006

By V. Gel

An analysis of the operation of rotary tilting furnaces has indicated that they ensure better recoveries of metal when smelting lump scrap from aluminum slags, brass and bronze. On the other hand, processing of slags (concentrates obtained by mechanical upgrading) in pear-shaped furnaces results in much lower performance values as might be expected. At the Novgorod metallurgical plant a process for blister copper production in a rotary TROF converter (Outokumpu, Finland) has been introduced on a commercial basis. Smelting of brass and bronze scrap to produce blister copper is carried out using the technology developed in Russia and differing from the Outokumpu technology by the types of flux used and the blowing conditions in fuel burners and for melt oxidation, as well as by the design of gas removal system, the design of nozzles for melt blowing and the use of carbonaceous reductant (coal) for magnetite reduction in slags. Industrial-scale testing has demonstrated that by means of special techniques the 30-tonne converter productivity can be increased by 30% to 40% as compared with its rated productivity.

Jan 1, 2006

By H. Cepin

Production of non-ferrous metals is still principally performed in shaft and flame fired furnaces. Electric furnaces increase metal recovery, reduce environmental burdens and decrease energy consumption compared to conventional processes. Because non-ferrous metals have low melting and boiling points and aggressive slags design of the furnace, energy input, and slag conductivity and composition are very important. Secondary materials are easily handled in electric furnaces. Since additional amounts of lead, zinc and tin will become available from secondary sources in the future, electric furnaces are expected to replace conventional smelting furnaces. The paper describes technical, electrical, and process designs of electric furnaces peculiar to the reduction of non-ferrous metals. Electric and various thermic furnace processes are compared.

Jan 1, 1990

By Raymond PoIick

The Demag Electric Slag Cleaning Furnace installed at the Asarco Smelter in Hayden Arizona is one of the few rectangular electric furnaces now operating. The long transition times from charge to tap allow exceptionally clean skims (high recovery); however, the furnace design is complex. Additional Asarco requirements for rapid installation and commissioning further complicated the design. When operating and wear effects accumulated after two years of use, steps were taken to rebuild the furnace with enhanced durability based on the design parameters experience in actual use.

Jan 1, 1993

By Steven Wright

The extent and the rate of reduction of slags produced from the smelting of recycled lead batteries were investigated under laboratory conditions using graphite as reductant. Simultaneous reduction of PbO, Fe2O3, Sb2O3 and As2O3 occurred at temperatures of 1180 and 1200°C, with Sb and As reporting to the metal phase while the PbO content of the slag was above 2 wt%. Fuming of As from the metal occurred at lower concentrations of lead in the slag. Discard slags with low levels of As, Pb and Sb were produced. Arsenic levels were reduced to less than accurately measurable by ICP analysis, and Sb levels in the final slags were in the range of 0.1 to 0.2 wt%. The kinetic data obtained were analysed and compared with other measurements on lead oxide containing slags. The results showing a dependence of the reduction rate on the oxidation state and the basicity are consistent with other studies on well characterised industrial and. synthetic lead slags. These results indicate that when carbonaceous reductants are used, the rate of interfacial reactions play an important role in enabling the production of environmentally acceptable discard slags.

Jan 1, 1994

By Jin Liu

The mechanism and rate of carbon reduction of each of the phases that are formed in the flash flame, i.e. sulfide (matte) and oxysulfide, was investigated. Graphite-slag reduction was conducted for comparison purposes. The objective of these tests was to measure the rate of solid graphite reduction of respectively matte, oxysulfide, slag, and matte+slag mixture at different temperatures. More in particular, these tests were expected to permit understanding and explaining the reduction mechanism of each material by comparing the respective reaction rates, product reaction gas compositions and CO/CO2 ratios, reduced material assays, activation energies, and other relevant parameters. Direct visual inspection of the test crucibles would provide additional information.

Jan 1, 2006

By Mala Nath, Atjit Mallick, Asheesh Kumar

"The present research work is aimed to focus on the development of chemically stable light weight microporous carbonaceous material, such as activated charcoal incorporated either with titanium n-butoxide, titanium diisopropoxide bis(2,4-pentanedionate), vanadium 2,4-pentane-dionate or zinc 2,4-pentanedionate having varying wt% of the metal (2-8%) using ethanol as solvent at 40--50 oC followed by calcinations at 100, 150 and 200 cC, except the samples with titanium diisopropoxide bis(2,4-pentanedionate) which are calcinated at 80 oC. Atomic absorption studies along with FESEM revealed that the maximum incorporation of metals (Zn, V and Ti) in activated charcoal was observed with 4 wt% of zinc 2,4-pentanedionate calcinated at 150 oC , 4 wt% of vanadium 2,4-pentanedionate at 100 oC, 2 wt% of titanium n-butoxide at 100 oC and 2 wt% of titanium diisopropoxide bis(2,4-pentanedionate) at 80 oC, and equilibration time of 20-24 h was used in each case. Hydrogen sorption behavior in these carbonaceous materials has also been studied at 77.4 K and low pressure up to I bar. The highest hydrogen uptake obtained was 1.45 wt% (164.5 cm3 (STP)/g at P/Po = 1.0) for activated charcoal incorporated with 4 wt% of zinc 2,4-pentanedionate calcinated at 150 oC.IntroductionTwo of the major challenges for humanity in the next twenty years are the shrinking availability of fossil fuels, the global warming and potential climate changes that result from their ever-increasing use. So it is necessary to fmd an energy source that is convenient, flexible and controllable. One possible solution to these problems is to use an energy carrier such as hydrogen, and ways to produce and store hydrogen in electric power plants and vehicles. Hydrogen storage is the bottleneck for the breakthrough of hydrogen as energy carrier in automotive applications [1]."

Jan 1, 2012

By Hong Yong Sohn

On the occasion of this symposium in my name, I reflect upon the contributions of my academic mentors and early associates who helped shape my professional career. I was fortunate to have these people around me during my graduate work and at the start of my professional career. In forming my view of the technical field and career, they represented academia, research institutions, industry, and different parts of the world.

Jan 1, 2006

By Guo Xueyi

The reaction mechanism for the manganese dioxide reductive dissolution in acidic chloride media in the presence of ferrous/ferric ions are based on theoretical delineation and dual cell experiments. In terms of the Buttler-Volmer equation and chemical kinetic principles, a electrochemical kinetic equation was deduced, which successfully provided a theoretical basis for describing the role of Cl-, Fe2+, Fe3+ and H+ in solution, as well as their interrelationship in manganese dioxide reductive dissolution. Dual cell experimental studies indicate that the increases of Cl- and Fe2 in solution are helpful to accelerate the couple process; while, Fe3and Mn2+ hinder the coupled reaction to some degree. Higher acidity in solution is beneficial to the dissolution of MnO2. All the dual cell experimental results are consistent with the theoretical deduction. This study will be useful to understand the mechanism for the leaching of manganese nodules from the deep ocean, as well as the leaching of manganese dioxide ore from land.

Jan 1, 2003

By V. K. Kalyani

The present paper discusses a three layer feed forward artificial neural network (ANN) model, trained using the error back propagation algorithm, has been established to simulate the column flotation circuit used for beneficiation of Sillimanite. Parameters such as superficial air velocity, wash water rate, froth height, % solid, feed velocity, sodium silicate and oleic cid are considered as process operating variables and % yield of Sillimanite is the output of the experiment. The results from the ANN modeling, involving the non linear relationship between inputs and outputs, indicate good agreement with experimental observations. The network model validates the experimentally observed trends. The optimal model parameters in terms of network weights have been estimated and can be used for computing parameters of the process over wide-ranging experimental conditions.

Jan 1, 2006

By M. D. Street

Lead and zinc production commenced in 1966 at Brunswick Smelting using the Imperial Smelting Process. In 1972 the blast furnace was modified to produce lead bullion only which was refined to corroding grade lead using conventional kettle refining techniques. Since 1972 consumption of lead concentrate and production of refined lead has doubled and this paper describes changes to operating and maintenance techniques which have contributed to this improvement. Reference is also made to improved environmental, health and hygiene practices at the smelter.

Jan 1, 1983

By Mitsuhiro Ohtaki, Tetsuzo Arakawa, Fujio Murata

Refining of Zn from aluminum scrap melt by some vacuum distillation processes was studied to promote aluminum scrap recycling. Effects of distillation conditions, such as melt temperature, vacuum pressure and holding time, on Zn distillation behavior were investigated theoretically and experimentally by 0.3kg/ch scale vacuum resistance furnace. Three methods to increase the surface-area/volume ratio of liquid metal, such as gas atomizing, mechanical atomizing and mechanical stirring, were tested to increase the Zn distillation rate in 5kg/ch scale vacuum resistance-furnace. It was easy to lower the remaining Zn content to less than 0.1 wt% within one minute by mechanical stirring method. A water-model simulation experiment indicated that a significant agitation of the melt by stirring would be effective to increase the distillation rate. Continuous agitation vacuum distillation process (CA VP) has been designed and the pilot plant is now in construction.

Jan 1, 2000

By Natasa Mitevska

In the world, as well as in Republic of Serbia, conventional ore reserves are almost exhausted, so the problem of their shortage is more and more expressed. On the other side, there are many locations with significant reserves of polymetallic ores which present huge potential but cannot be classically processed. Each of these classes of materials has particular mineralogical characteristics which affect their processing. Because of that it is necessary to develop particular technology for each unconventional ore in order to extract valuable elements. The aim of investigation was to define technology for complex processing of the Blagojev Kamen sulfide concentrate by pyrometallurgical procedure in order to valorize valuable non-ferrous and precious metals present, and profit with absolute respect of environmental protection laws. The complex composition of the Blagojev Kamen sulfide concentrate with high content of non-ferrous (15.59% Pb, 9.05% Zn, 2.37% Cu) and precious (697 g/t Au and 744 g/t Ag) metals was the main factor for technological procedure and collector selection. Laboratory investigations are done in four series according to technological scheme: oxidizing roasting, charge preparation (flux addition and agglomeration), smelting under reducing conditions, lead bullion refining, Dore metal refining to final products. It is concluded that precious metals are concentrated in lead bullion (up to 97.95% of gold and 93.37% of silver), which has similar composition to lead bullion produced in lead metallurgy. In this case, simplified technology is used for lead bullion processing because of low content of arsenic, bismuth, etc.

Jan 1, 2006

By John M. Rapkoch

In the continuing search for copper matte converting methods, commercially available and feasible choices remain Peirce-Smith Converters, Hoboken Converters, Mitsubishi Converting, Ausmelt converting, and Outokumpu/Kennecott Solid Matte Oxygen Converting (?Flash Converting?). While each alternative improves on Peirce-Smith Converters? limited fugitive gas capturing capability, the Peirce-Smith Converter is relatively easy and economic to operate and has an unmatched ability to accept valuable but difficult-to-handle material such as scrap anodes and purchased scrap copper. Recent experience with designing, building, and starting up an ISASMELT facility, applied in primary smelting of copper concentrates, has led the authors to speculate on how suitable the ISASMELT process would be for copper converting, given its low fugitive gas release and its ability to accept a variety of feed types. This paper reviews the potential metallurgical challenges posed by converting copper matte in an ISASMELT vessel and considers possible engineering and design challenges posed by the inclusion of this technology into a new or refurbished copper smelter.

Jan 1, 2006

By Jeaneth S. Benedetto

The physical and chemical processes developed for recovery of uranium and phosphor from phosphoro-uraniferous ore bodies consists of three basic steps: concentration of the phosphate bearing uranium by flotation, chemical dissolution of the concentrate by wet phosphoric acid and extraction of uranium by solvent. In this process two products are obtained: 1) uranium and 2) phosphoric acid. The purpose of this work was to develop technological know-how of phosphoric acid purification though an extraction of P2O5 by solvents. It was investigated by two lines of research. In the first one the uranium was extracted before the phosphoric acid purification. In the second, the phosphoric acid was extracted before uranium recovery. The comparison of the two processes is shown in this paper. Experimental work was developed on a laboratory scale to select and optimize the process variables. After the laboratory study, the research of extraction and stripping was continued on a pilot scale in pulsed perforated-plate columns in order to investigate the main operational and process conditions. The first phosphoric acid extraction experiments showed good results using a raffinate sample obtained from the uranium extraction process. It was possible to obtain a high purity phosphoric acid.

Jan 1, 2003

By Xiaorong Liu

Interfacial emulsion generated in copper solvent extraction is an inhomogeneous O/W emulsion that consists of organic phase, aqueous phase and solid particles. In order to determine what kind of components in organic phase promotes the emulsion, the organic phase separated from the interfacial crud provided by Dexing Copper Mine in Jiangxi, China was analyzed for its components by combined gas chromatography-mass spectroscopy. It was found that many kinds of emphiphiles containing such hydrophilic groups as carbonyl, carboxyl, or acylamine existed in organic phase, most of which were originated from the reagent degradation. Conclusively, Lix984N would degrade gradually during a long-term contact with the acidic aqueous feed and strip reagents. Lix84 and nonylphenol, as effective components of Lix984N, degraded almost completely after long-term recycling. As a result, the effective components of Lix984N were far lower in concentration than the dense-aromatic impurities derived from the diluent and the degradation products in total. The degradation of Lix984N would deteriorate solvent extraction, disengagement performance and result in more serious interfacial emulsion.

Jan 1, 2006

By F. L. Meng, C. S. Henkel, R. M. Alchalabi

For secondary aluminum producers to maintain a profitable melting operation, five technical factors have to be taken into account from the initial furnace building decision to the final operation and production. These factors are furnace design, furnace equipment selection, furnace control, furnace charge selection and inventory, and furnace operation. Any of these five factors, if not chosen or performed wisely, will likely result in sub-optimal melting operation. As a result the MeltSim melting optimization package has been developed by the collaborative effort of Chinook Sciences and AMCS Corporation to take into account these five factors. The package is a mixture of hardware, software, science and experience. The package incorporates years of reverb furnace operational observations, start-up installations, furnace operator experience and furnace physiochemical mathematical model development. The optimization package enables aluminum producers to design new furnaces, select and place proper equipment, optimize existing furnace operations, and convert air-fuel installations to oxy-fuel. The package provides furnace operation monitoring and advisory signals, and furnace automatic optimal control to furnace operators, shift supervisors and plant managers, all customized, based on plant and melter need and ease of information management.

Jan 1, 2000

By Dan Adams

A number of gas-liquid processes require high intensity agitation systems to provide uniform blending and dispersion of reactants in order to achieve desired end products. Processes such as hydrogenation, fermentation, and minerals processing have used conventional down pumping or radial agitation systems with some success. In 1996, LIGHTNIN introduced the concept of Up-Pumping to the industrial marketplace as an improved mixing technology for these applications. For processes requiring gas-liquid mass transfer, such as those listed above, conventional mixing technology requires the use of gas introduction devices (sparges) below impellers. These devices can be a maintenance concern due to plugging and erosion in the presence of solids. Up-Pumping impeller systems are able to draw in a significant amount of gas from the headspace, much more so than conventional vortexing impellers designed for headspace gas incorporation. This paper will demonstrate the effectiveness of Up-Pumping impeller systems that have the potential to eliminate need for sparge devices entirely. It demonstrates the ability of Up-Pumpers to re-entrain gas for higher utilization compared with conventional impeller technology. This is significant in applications using costly gases such as enriched oxygen or hydrogen, reducing overall operating costs of production.

Jan 1, 2003

By S. de Vries, B. Wasmund, J. Metric, N. Voerrnann, S. Kasinger

Gulf Chemical & Metallurgical Corporation (GCMC) operates a circular DC electric smelting furnace to treat nickel and cobalt bearing residues at its plant in Freeport, Texas. The furnace, originally built by others, has experienced problems including runouts through the hearth and the lower sidewall. Hatch has designed several improvements to the furnace to alleviate these problems. The single anode at the centre of the hearth was replaced with a patented system of twelve air-cooled copper anodes evenly spaced around the furnace lower sidewall. The DC power supply comprises two transformers and two rectifiers operating in parallel. The water-cooling system on the bottom and lower sidewall shell plates was replaced with an air-cooling system using copper cooling fins. The existing row of water-cooled copper coolers in the metal bath zone was re-designed for greater heat removal capacity and better element joint sealing, and a new row of water-cooled copper coolers was added to cool both the alumina bath and freeboard zones. The existing water-cooled metal and alumina tapblocks were also re-designed for more robust cooling. A binding system was added to provide refractory compression that reduces the risk of liquid leaks. Finally, the furnace tilting frame was relocated to the top of the furnace where it is less likely to be damaged.

Jan 1, 2000