Search Documents

By K. Adham

"Fluidized beds are utilized in a wide range of high-temperature applications throughout the metals and materials industry. Their main advantage is the fast and uniform heat and mass transfer between the hot combustion gases and the particulate solid feed. A further benefit can be the lowering of the processing plant's energy consumption, through heat recovery from the fluid bed processes used for solids heating. Here, the enhanced energy efficiency of fluidized systems is investigated and the modeling results are discussed for three configurations: the flash tube, the single bubbling bed and the multi-stage fluid bed. Key thermal design aspects of each system are identified based on results from process simulations, in order to benchmark their main operating features and overall energy efficiency. Suitability and applicability of each configuration is also discussed based on a number of process and material property considerations.IntroductionCombustion based heating of particulate solids is commonly done using three different types of fluidized beds. The flash tube (FT) is similar to a hot pneumatic transport system. The single-stage fluidized bed (FB) typically uses in-bed combustion. The multi-stage fluidized bed (MSFB) can have two or more stages stacked into a tower.Flash tube (FT) suspends the incoming solid charge in a high-velocity stream of hot combustion gases. To maintain the solids suspension in the FT, two parameters are required: high velocity for elutriation of the particles and adequate solid-to-gas ratio for avoiding high pressure drops and solids drop-out [l].The fluid bed (FB) works at much lower velocities than the flash tube. Therefore, most of the solids are not conveyed in the gas stream, but are only suspended in a liquid-like manner. At minimum fluidization velocity (Umr), the gas flow exerts just enough force on the solids to keep them suspended in place [2].Multi-stage fluid bed (MSFB) heats up the solids as they are transferred from an upper bed level to a lower one, counter-current to the rising flow of hot gases generated at the lowest stage. As the temperature and volumetric flow of the gases decrease from bottom to the top stage, smaller bed diameters can be used in the energy recovery stages [3]."

Jan 1, 2014

By Akihide Hosokawa

The void growth and coalescence in model materials involving a pre-existing three dimensional void array (i.e. multiple layers of a void array) was studied by X-ray computed tomography (XCT) coupled with in situ tensile deformation. To reduce the recording time, a new technique called fast tomography was employed. The model materials used in this paper were fabricated by the combination of an ultra-short pulsed laser machining system and a diffusion bonding technique, and two different types of arrays were prepared namely, FCC 1 and FCC 2 type array. This methodology allowed the authors to capture the entire process of growth and coalescence events of a void array embedded in the metal matrix. The failures in the both materials involved internal necking and shear localization. One of the highlights of this paper is that the plastic strain at the onset of void coalescence was measured for each model material. These values are in fact the adequate values to be compared with the coalescence strain predicted by existing void coalescence models such as the Brown and Embury model, the Thomason model and the Pardoen and Hutchinson model. The comparison suggested that the Brown and Embury model underestimated the coalescence in neither of the current model materials, while the Thomason model and the Pardoen and Hutchinson model showed a quite good agreement with the result for FCC 1 material. On the other hand the result from FCC 2 material agreed with none of the models probably due to the geometry of the void array that is not compatible with the existing models.

Jan 1, 2010

By K. Morsi, S. K. Kassegne, K. S. Moon, A. Numula

"Current Activated Tip-based Sintering (CATS) is a new process for the powder-based manufacturing of macro, micro and possibly nano-scale features and shapes. CATS enables the selective sintering of powders by localizing current activation conditions through an electrically conducting small tip (either in the stationary or moving mode). This paper presents preliminary experimental results on the CATS of reactive mixtures of Ni/Al powder to form nickel aluminide intermetallics. Preliminary investigations on the effect of current on the reaction characteristics are discussed.IntroductionSpark Plasma Sintering (SPS) has been the subject of intense research over the past decade [1,2, 3,4,5,6]. The process boasts remarkable advantages which include ultra fast heating rates (hence by-passing low temperature non-densifying sintering mechanisms), considerably lower sintering temperatures and shorter sintering times than achieved in conventional sintering. The process is however limited to the generation of simple geometries on the macro-scale. Recently three of the authors conducted work on a novel process ""Current-activated tip-based sintering (CATS)"" [7], where electric current is passed through a conducting tip that is placed or allowed to travel over a powder bed/compact to locally sinter powders. lD, 2D and 3D micro-scale sintered shapes can be generated with the possibility of 3D rapid prototyping on the macro/micro or nano-scale. Although CA TS of single phase powders has been conducted, the CATS of reactive powders has not yet been investigated.The Ni-Al phase diagram contains five intermetallic compounds, AhNi, AhNh, AlNi, AhNi5 and NhAl. Out of these intermetallics, NiAl and NhAl have received the vast majority of scientific and industrial interest [8]. NhAl can be formed by reaction synthesis, where nickel and aluminum reactant powders are heated to a reaction ignition temperature at which the reactant powders are converted to the intended intermetallic product. The reaction is exothermic which gives rise to considerable compact self heating, thus instantaneously raising the compact temperature by several hundred degrees which facilitates sintering [8]. Applying and electric current locally would not only provide for a rapid local reactive sintering, but would generate a number of intriguing scientific investigations. For example, of interest would be, how would the reaction propagation and microstructural/phase evolution be affected by the temporal and spatial temperature and current distributions."

Jan 1, 2011

By F. Sanchez, A. Mejias, C. Frias, G. Diaz

"Crude zinc oxides are the major source of secondary zinc and are produced from fuming processes like Waelz kilns. The impurities of crude zinc oxides make difficult their processing in primary zinc refineries due to mainly high chloride tenor. Washing with sodium carbonate is a costly operation and chloride removal efficiency is not good enough, so further purification steps are required. The crude zinc oxides are easily treated using ZINCEX™ technology based on leaching, solvent extraction, and electrowinning. The ZINCEX™ process is commercially available and is designed to be a perfect barrier for metallic impurities and halogens, allowing selective zinc extraction in mixed chloride and sulfate leaching solutions. Other valuable components as lead and silver can be efficiently recovered from the leaching residue using PLINT technology in chloride media. Silver is recovered as silver cement and lead is precipitated as pure lead oxide or carbonate, which can be smelted at low temperature.IntroductionZinc is a fully recyclable metal and at present approximately 70% of the zinc produced worldwide comes from primary zinc while 30% originates from secondary materials. Nowadays, the zinc recycling rate is continuously increasing mainly through galvanized steel scrap processing, and crude zinc oxides are the major source of secondary zinc [1]. Secondary zinc oxides are obtained from fuming processes like W aelz Kiln, Rotary Hearth Furnace or Primus Furnace. Waelz is the dominant technology accounting for 80% of total crude zinc oxides production worldwide. In the Waelz process, steel dust is mixed with solid fuel reductant (coke breeze) and pelletized. It is then fed to the kiln and heated to a reaction temperature of l ,200°C. In such conditions, zinc, lead, and other non-ferrous metals are vaporized into the flue gas together with chlorides and alkaline metals. Mixed oxides are drawn from the kiln with the process gases and separated to produce typical crude zinc oxides [2]."

Jan 1, 2011

By G. R. Waters

NMR360 is developing a suite of chloride-based metals extraction processes, with the first commercial operation scheduled for commissioning late in 2018. It is critical, therefore, that with the introduction of any new technology, that the circuits do not suffer from mechanical failures which will compromise the operation. Although chloride leaching is at atmospheric pressure and relatively low temperature, the main challenge is preventing corrosion, since the high proton activity makes even a small amount of acid behaves as though it were concentrated. An additional challenge in concentrated chloride circuits is the potential for solids precipitation. In this context, therefore, correct valve selection is crucial, and NMR360 has partnered with CGIS to ensure that the Severe Service Valves (SSVs) needed will perform over and above the definitions of the Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry. This paper outlines what the minimum requirements are for SSVs in chloride leaching applications, drawing on five decades of industry experience from one of Canada’s leading valve experts.

By Jose R. Parga

In mining operations, cyanidation is the ,predominant method by which gold and silver are recovered from their ores and it is recognized that cyanide consumption can be a major factor that contributes to the operating costs for such operations. Also after extraction and recovery of precious metals a certain amount of cyanide is delivered to the tailings pond and must be considered with respect is environmental problems due to the toxicity of cyanides. In this regard, the Air-Sparged Hydrocyclone (ASH) has been used as a reactor for the treatment of cyanide solutions in two ways; first for cyanide recovery by acidulation using the Mexican modification of the Mills-Crowe process and second for cyanide destruction by oxidation with the use of chlorine dioxide (ClO2). In both cases, excellent performance can be achieved using the high capacity ASH system.

Jan 1, 1998

By K. Robinson

Following the longest Smelter campaign in BCL?s history it was planned to completely rebuild the flash smelting furnace in 1987. This was the fourth major overhaul and the most extensive so far attempted. Detailed planning took place over several year$ preceding the shutdown and implementation was completed in 54 days. The key to minimising shutdown time was the method designed for installation of the new uptake shaft and reaction shaft. Major repair work was also undertaken in the waste heat boiler and electric furnaces. Both of these activities had an impact on the critical path of the flash smelting furnace overhaul.

Jan 1, 1993

By A. Deneys

An experimental technique has been devised for studying the reaction kinetics of the reaction: ZnO + 2Fe0 = Zn(g) + Fe203, by which zinc evolution can occur from a molten slag bath in the absence of a carbonaceous reductant. When studying the reaction kinetics by heating from room temperature, solid state reactions and poorly defined melting points may obscure the starting point of the reaction. In order to eliminate this problem, an experimental technique was devised whereby two molten slags could be melted independently, and then mixed, to provide a well defined starting point from which to begin taking measurements. Two crucibles were mounted in a vertical reaction cylinder. The upper, mild steel, crucible had a bottom pouring plug which was sealed by a steel stopper rod. A fayalite mixture was contained in this crucible. The lower crucible contained an A12O3-CaO-SiO2-ZnO solution. Once the two slags had been melted, the steel stopper rod was removed from the upper crucible. The upper, reduced slag (fayalite in equilibrium with the upper steel crucible), drained into the lower crucible where the two slags were mixed by submerged argon stirring. Dip samples were taken to measure the zinc content of the final mixture as a function of time. The experimental procedure will be described, as well as results of experiments which were conducted on synthetic slags. The system investigated was similar to the lead blast furnace slag which is produced by the primary lead smelters of Missouri, USA.

Jan 1, 1997

By Katia Vutova, Vania Vassileva

Investigations and results on the refining of tungsten scrap applying electron beam melting (EBM) in vacuum are presented and discussed. In this work EB melting experiments were performed in single or double-melt operations with different power inputs and refining times for tungsten purification and recovery of multiple metals (including refractory and other metals such as Mo, Nb, Cu, Zn, etc.), which are alloyed elements or impurities with high concentrations in the initial materials. Evaluations for extraction of some valuable metals, generated in the condensate at their removal from the liquid metal during the refining process are provided. Efficient technological regimes for e-beam melting and refining that enable the simultaneous production of pure metal ingots and condensates that can be used directly or can be used for subsequent extraction of expensive and valuable metals are presented.

Jan 1, 2016

By Sharif Jahanshahi

Calcium ferrite slags are often associated with Professor Yazawa due to his pioneering work on the thermodynamics of this type of melts. Over the past years CSIRO has invested some effort in studying physico-chemical properties of such melts to fill in some gaps in our knowledge and explore opportunities for application of the understanding developed. These investigations cover thermodynamics, transport properties of calcium ferrite based slags, as well as the kinetics of reactions of such slags with refractories. The present paper provides an overview of some of these studies and highlights some of the interesting behavior of such melts, The oxidation state of copper and arsenic in calcium ferrite based slags are predominantly Cu+ and As3+, respectively, at oxygen potentials below 10-7 atm. The concentration of CU2+ in such slags becomes significant at oxygen potentials of greater than 10-7 atm at 1300 °C. The activities of CuO0.5 and AsO1.5 in calcium ferrite slags show strong deviations from the Raoultian Law, while that of CoO is very close to ideal behaviour with respect to pure solid CoO. Addition of SiO2 to calcium ferrite slags can have significant effects on the activities of FeO and Fe2O3 and hence the stability of magnetite phase. Transfer of oxygen in calcium ferrite slags is fast with diffusivity of 2x 103 cm2/s at 1350 °C and activation energy of 16 kcal/mol. Presence of solid phases, such as magnetite, has pronounced effect on the viscosity of calcium ferrite slags. The observed dependence on solid loading and shear rate indicates deviation from Newtonian behaviour. The interfacial tension between copper mattes and calcium ferrite slags is strongly dependent on the matte grade, with the determined values being much lower than the corresponding ones for interfacial tension between similar mattes and iron silicate slags. MgO, Cr2O3 and MgCr2O4 have low solubility in calcium ferrite slags and their solubility increases with increasing copper oxide content of the slag at 1300°C. The oxidation state of the slag has strong effects on phase transformation, dissolution rate and disintegration of refractories in calcium ferrite slags. Other key factors with major impact on slag-refractory interactions include viscosity and surface tension of slags as well as the contact angle between slag and refractory material,

Jan 1, 2003

By M. Jortikka

The smelting process of the old reverberatory furnace including its capacity has been improved over the years in different ways eg. with oxy-fuel burners, parallel reactors with the reverb or with various modifications of the reverb furnace itself. The future reverb modifications with old concepts are difficult or impossible as the increased copper losses in slag call for separate slag treatment and particularly the process modifications do not solve the environmental issues but instead mean unavoidable high capital and operating costs in gas cleaning and sulphur recovery. During the last decades improvement in process performance and increase in capacity of copper flash smelters has been achieved easily by substituting the pre-heated process air by highly oxygen enriched air. The flash furnaces of today, however, are inherently designed to operate with high oxygen enrichment. Further process improvement with a view to production costs and capacity increase as well as to the more stringent environmental requirements is possible with even higher oxygen enrichment. This, apart from the advantages it generates, requires improvements in and careful design of the feed system, concentrate burner, furnace cooling and the off-gas line as well as adaption of the flash converting instead of the conventional Peirce-Smith converters. A logical answer even for the revamping of the reverb smelters in the future is the total replacement of the reverb furnaces with flash smelting together with flash converting. This paper discusses the possibilities for future process improvements of the existing flash smelters taking into account the process concepts, equipment modifications and capital aspects not forgetting the environmental issues. The revamping of the PASAR smelter in Philippines is introduced as an example of a recent success story.

Jan 1, 1994

By Wang Shulan

The synthesis process of BaTiO3 from TiO2 and BaCO3 in the molten NaOH-KOH at 350oC was studied by the A.C impedance technique. The A.C. impedance of molten NaOH-KOH (xNaOH = 0.36) and the variation of the conductivity of the salt with time during the synthesized process were measured. The synthesized reaction of the BaTiO3 and the decomposition reaction of BaCO3 are fast and were finished in 10min. The interaction between TiO2, BaO and BaTiO3 and the molten salt was confirmed by the variation of the conductivity.

Jan 1, 2005

By J. A. Holmes

Due to varying and complex mineralogy, the flotation tailings from the Chingola Concentrator have, for some years, contained upwards of 0.4% acid soluble copper. In 1968, an investigation was initiated, to determine a method for recovering this acid soluble copper. This initial investigation concluded with a recommendation to install a leach-solvent extraction-electrowinning plant at Chingola, to treat up to 900 000 tonnes of material per month, for an additional copper production of some 4 500 tonnes per month. The process consists basically of six stages :- Materials reclamation handling and preparation, acid leaching in air agitated pachucas, solid-liquid separation by countercurrent washing in thickeners, solution concentration and purification by solvent extraction, copper recovery by electrowinning, and residue neutralisation and disposal. This paper describes the development of the main parameters for design of each of the six sections, and gives details of the final plant design. Problems encountered in commissioning and initial operations are commented on, particularly insofar as they indicated any errors or misjudgements in the design. The choice of materials of construction is commented on in some detail.

Jan 1, 1976

By A. Dadgar

The adsorption kinetics of AuBr4 on Dowex ® -21K ion-exchange resin were studied and found to be independent of the initial gold, bromine, and base metals concentrations. A commercially-available undivided hypochlorite generating cell was used to generate bromine from simulated mixed halide (Br-/CI-) solutions. Electrolyses were performed with solutions containing very low Br' ion concentrations. The current efficiencies were 80-90%, and Br- ion utilization was maximized. A detailed economic assessment was made considering the capital and the operating costs for a 1000 mtpd gold ore processing plant. The toxicity and discharge levels of bromide, bromine, and cyanide were compared from a detailed analysis of the published literature data. Comparing bromine vapor with hydrogen cyanide gas for a given length of exposure, the lethal concentration of bromine is about 3 times less than hydrogen cyanide. The toxicity of sodium bromide is similar to that of sodium chloride. Acute poisoning to bromides and chlorides is rare because of their low toxicities. The allowed discharge levels of Br-, Br2, and CN- in fresh water are 250, 0.1, and 0.005 mg dm-3, respectively.

Jan 1, 1992

By Muhammad Abid, Kh. .. S. Karimov

"In this study, design and investigation of biogas digester consisting of methane tank with built-in solar collector to utilize solar energy for the heating of the slurry prepared from the dung and heat exchanger is designed, developed and tested. The digester was laboratory type and consists of cylindrical metallic tank of size of 0.5 m in diameter; 1 m in height and 200 liters in volume. The surface of the digester from outside was covered by thermo insulated material a glass wool, except of south side (in northern hemisphere). This side played the role of built-in collector and was blackened to increase absorption of solar irradiation and covered under 45o by glass. In the blackened side of the digester on the different heights it was installed metallic pipes for the inlet and outlet of the air, connected with heat exchanger installed inside of the digester. The heat exchanger was fixed in the level above of the inlet pipe. The horizontal plane reflector concentrates solar beams to blackened side of the digester. In the winter period, it was found that the retention time of this digester is shorter on 15% and produced biogas volume is larger on 20% with respect of ordinary biogas digester. This digester is used for the demonstrative purposes and as a teaching aid presently and base on the results it may be used for the construction of large volume digesters for use in the farms, especially located in the remote and mountain areas where the climate in the winter period is cold. Introduction At present many experts around the world have focused their efforts to energy crises because energy is one of the most important factors for the development of the society. It is known that consuming energy is proportional to quality or standard of life. There is a close relationship between energy consumption and the Gross National Product (GNP). It is obvious that for further development of the country additional sources of energy is required, which are cheap, safe and environmentally compatible with respect to the action on possible wastes. Utilization of renewable energy is one route to help in solving the above mentioned problems. In particular, biogas as a source of renewable energy is produced by biotechnology and used wide on residential scale [1]. The biogas was produced for the very first time in 1814 by Deivy from organic wastes. In 1900 production of biogas was started in Bombay (India) [2, 3]. Biogas consists of 55-70% methane (CH4) and around of 27-44% carbon dioxide (CO2) and less than 1% H2 and H2S. At present biogas is used widely in some countries for lighting, machines, and vehicles, generators, cooking and heating. Biogas generation is suitable for small to large scale operation and at present is realized in a number of developed and developing countries as USA, Hungary, China, India etc. Since 1990s biogas projects construction in China has developed steadily by the end of 1998, there were altogether 6.88 million household biogas digesters [4]. In Russia biogas digesters are used for processing of hard dung into biogas [5]. Over the last few years the very first biogas digesters were constructed in Tajikistan as well [6,7] and it was found that the digesters can work with sufficiently high efficiency in mountain areas as well ."

Jan 1, 2008

By Gerald M. Rich

Magma Copper Company, a subsidiary of Newmont Mining Corporation, has initiated many changes in the continuous casting of 5/16 inch diameter copper rod since startup of the San Manuel rod plant in early 1972. With rod production at forty percent over design capacity, many production records have been established including a record cast of 761 tons of salable rod in a twenty-four hour period. The most challenging and rewarding introduction was the continued utilization of an alloyed copper casting wheel in lieu of the conventional steel wheel. With proper cooling and careful control of the mold release agents. as much as 58.000 tons of copper were cast on a single copper wheel. Other advantages are: 1) Fifteen percent increase in available casting time 2) Reject rod from steel inclusions was reduced by nearly one-hundred percent 3) Wheel cost was decreased by ninety-one percent 4) Natural gas consumption dropped approximately fifteen percent 5) Large increase in refractory component life 6) Reduction of manhours/ton. Many other modifications have contributed to excellent rod quality and high operating efficiency. A two-piece launder was replaced with a single castable launder which reduced oxygen pickup and provided better slag removal. Modifications to the bar preparation unit, pickling system, and coiler resulted in considerably higher milling efficiency.

Jan 1, 1976

By A. González

Arsenic is one of the main contaminants present in Chilean copper concentrates and its abatement represents a challenge for the process metallurgy, particularly under the strong environmental requirements in the global community. The possibility to form ferric arsenate directly from a gas phase by means of a heterogeneous reaction between an arsenic gas bearing and iron oxide was studied at laboratory scale. A thermodynamical analysis for the system Fe-As-O-S has been initially made, in order to obtain the stability conditions for the ferric arsenate or other FexAs2O2 type compounds. Experiments were made using an hematite sample suspended in a thermogravimetric device. AS4O6 gas generated from solid AS203 that was passed through the iron oxide sample and its instantaneous weight change was recorded directly. A kinetic study for the AS4O6 volatilization was made to control the gas composition. A chemical control between 300 and 600°C with an apparent activation energy of around 14 Kcal/mol As2O3 was determined. The samples after the reactions were chemically and XRD analysed. Arsenates detected corresponds to complex compounds. Results shows a dependence on temperature and oxygen content in the gas phase. The kinetics for iron arsenates formation is slow, reaching an arsenic capture of 6% after 80 minutes of reaction when an oxygen content of 50% is fed continuously at 800°C and 3,56% As in the gas. Experiences made at the same temperature but under higher oxygen content in a closed reactor, allowed arsenic capture close to 60%. For higher temperatures the capture is considerably lower.

Jan 1, 2003

By Pandey H. D.

The paper describes a fluidised bed ion exchange method for simultaneous removal of phenols and cyanide from the effluent. Use of an eluant enables regeneration of the resin in the continuous operation mode. The breakthrough experiments conducted both on the laboratory scale and on a pilot plant scale have shown that while the level of phenol can be brought down from 462 ppm to about 6 ppm, the free cyanide is almost totally removed. An examination of data indicates that the method can serve the twin objectives of pollution control and phenolic compounds recovery.

Jan 1, 1992

By George Oprea, Tom Troczynski, Joe A. Rigby, Waiman Lo

The refractory lining of the tuyere line in Peirce Smith converters have usually much shorter life in service than the rest of the lining, above or below it. There are already recognized chemical, thermal and mechanical factors which contribute to the wear of the lining. Our study presents the experimental results on microstructural changes occurring on these tuyere line bricks in a nickelcopper converter. The experimental bricks, after use at the tuyere line, were investigated using SEM/EDS and XRD techniques, to identify the mineralogical changes due to interactions with the nickel-copper matte or fayalite type slag at the process temperatures. The microstructural changes were correlated with physical and mechanical properties of the brick before and after use and a wear mechanism was suggested. Although the matte does not theoretically react with the mineralogical components of the brick, a partial oxidation of the Ni-Cu sulphides was identified using a line analysis by SEM/EDS in the densified layer at the hot face, which allows for mineralogical changes at the matte-refractory interfaces, with a high probability of microcrack formation due to the thermal cycling during use. These microcracks were also identified to open through inter-granular fractures parallel to the hot face, which appeared to be the main cause of lost lining during use. The reactions between the fayalite slag and refractory brick could eventually play a role in chemical dissolution of the brick only in the superficial layer at the hot face, as no slag components were identified deep into the brick.

Jan 1, 2009

By Preston C. Holloway

Transformational roasting involves the heating of a material along with specific additives to induce mineralogical changes in the starting material. By controlling the chemical composition, roasting atmosphere, temperature and time of reaction, the mineral transformations induced during roasting can be engineered to control the distribution of valuable, or harmful, metals and to produce new mineral assemblages that are more amenable to conventional methods of metals recovery or to environmentally safe disposal. To date, this type of process has only been applied to the recovery of a limited number of metals, but current research is looking to expand the application of these techniques to the recovery of metals from a wider range of materials. An introduction to these techniques is presented along with preliminary results from their application to metals recovery from zinc bearing wastes, such as zinc ferrite leach residues and carbon steel electric arc furnace dust.

Jan 1, 2006