Search Documents

By Richard L. Ash

In many instances, blasting exerts the dominant control over the economics and safety of excavation, where the materials involved are too hard and tough to be fragmented efficiently by other means. However, associated with the fragmentation process other effects very often result that are not desirable and may even be hazardous, such as fly rock, air blast, excessive overbreak, and damaging ground virbrations. It has always been the desire of those concerned with blasting to better control the forces involved so as to improve the breakage of materials, but at the same time reduce, or eliminate if possible, the unwanted side effects. Until the last decade or two, little was known of the phenomena concerned with blasting. However, since that time many investigators have studied blast mechanisms produced from both chemical and nuclear explosions, with the result that general concepts of the principles have been developed. But, in general, it is assumed that the energy from the explosion would be propagated spherically throughout the material, the latter of which for convenience of analyses is considered homogeneous and isotropic, i.e., the properties are the same in all directions, However, rocks are not isotropic as a rule, and evidence clearly indicates blasting forces rarely function uniformly or in spherical form as theorized.

Jan 1, 1965

By J. Jeffrey Wagner, Michael J. Bailey, Peter M. Douglass

The Chambers Creek Interceptor Sewer Tunnel project consisted of 2-1/2 miles (4 kilometres) of nominal 9-foot (2.7-metre) O.D. tunnel driven through predominantly glacially overridden soils. Mole-Collucio Construction Company initially elected to drive the entire tunnel with a Lovat TBM. However, this machine could not control the fast raveling ground conditions which developed when the TBM encountered sands overlying very dense, hard glacial till or boulders. As a result, a shield and digger machine was brought in for a 1700-foot (518-metre) long segment. Pumped wells spaced roughly 50 to 125 feet (15 to 38 metres) apart were utilized to dewater about two-thirds of the alignment during construction. Initial support consisted of steel ribs and wood lagging, with a final lining comprised of pre-cast concrete pipe segments grouted in place.

Jan 1, 1985

By Russell W. Hunt

The cave man of ages past took his wife-and family from the cave pointing to a fire he had built and beating on his breast said, "Look what I have done". Today man is taking his family back to a cave saying, "Come enter in because of what I have done". At the close of World War II Germany said if they had gone underground one year earlier with more of their operations, the war could have lasted four years longer with perhaps much of Britain devastated. The protection of the home front no longer rests with the soldier in actual combat. The battle will be won at home with the most careful kind of protection against missiles. After Nagasaki-Hiroshima Sir Winston Churchill said in substance "Up to now the Almighty has mercifully withheld from man the knowledge of these terrible weapons of destruction."

Jan 1, 1959

By Brian Fulcher

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft 3/sec) of water into Southern California. The 13 km (8-mile) tunnelling project is well underway and consists of two, 5.8 m (19-ft) diameter TBM bores through extremely variable geological conditions. An extensive and essential pre-excavation drilling and grouting program was performed in all reaches of the Arrowhead Tunnels Project, located north of San Bernardino, CA. This program supported the advance of two hybrid hard rock TBMs though extremely challenging ground conditions under substantial ground cover and up to 27 bar (900 ft) of ground water pressure. The well known San Andreas Fault lies nearby and has greatly influenced the local geological conditions. This paper will describe the means, methods and materials used throughout the numerous phases of the pre-excavation grouting program. It will also describe many versatile, flexible and innovative drilling and grouting methods and equipment systems utilized to improve performance, save time and costs in constantly changing geological conditions. Considerable lessons learned have been learned while overcoming some extremely formidable ground conditions and safely advancing the tunnels.

Jan 1, 2008

By Nick Salisbury, Alan Howard, Scott Tunison

INTRODUCTION Geotechnical investigations for tunneling projects typically use vertical test borings and, to a lesser extent, angled borings. Horizontal drilling applications were often limited to specialty testing programs and to perform probe drilling from a tunnel boring machine (TBM) as part of production tunneling. The former often involved cumbersome setups with skid rigs and cribbing in a pilot tunnel or shaft. The latter usually was limited to generic probing for rock quality and ground water conditions with no sampling. Neither yielded continuous core at production rates suitable for design and construction planning. Conventional vertical investigations still make sense in many instances, particularly for tunnels planned beneath urban settings where truck access is convenient and where the tunnel horizon is not readily accessible via a portal or shaft. However, equipment is presently available to conduct horizontal geotechnicall investigations at reasonable production rates and cost. Advantages include continuously sampling the tunneling horizon and minimizing “access drilling” to get the zone of interest at the underground construction horizon. Horizontal boring lengths of up to approximately 800 m are considered feasible and those in the range of 150 to300 m are now routine. These capabilities make horizontal borings an attractive option to consider when looking at deep tunnels beneath ridges, especially where access is limited. Fewer drilling staging sites can also mean reduced environmental impacts when investigating tunnels proposed beneath sensitive lands such as public wilderness areas. Investment in early construction packages to develop portals for investigation access and, possibly in excavating test shafts for the same purpose should even be considered. Potential benefits in the form of achieving improved overall project costs using horizontal borings exist because of the significant additional data collected in the tunnel horizon. For this reason they should be considered during the routine cost-benefit analyses generally conducted for planning geotechnical investigations for tunneling. The authors also believe that collection of such data will reduce Geotechnical Baseline Report (GBR) conservatism and lead to lower potential for

Jan 1, 2005

Using a series-model of an automotive short range radar sensor (SRR) and a recently completed experimental radar system, field tests have been performed in a surface mine. It was examined, to what extent low-cost electronically scanning radar sensors can provide useful data for assistance systems on large scale mining machines. Simple sensors are useful for anti-collision safety zones or hopper car automation. The more complex and sophisticated experimental radar system using digital beam-forming can clearly detect and map the contours of trenches and slopes. The overall promising results refer to many more potential applications for electronically scanning radar in surface and underground mining as a reliable alternative to mechanical laser scanners.

Jan 1, 2007

By Madan M. Singh

This section is unique to the Handbook in that it is the only section that deals with underground excavations for nonmining purposes. The editors were of the opinion that the section should be incorporated because the subject matter covered by the chapters is closely related to mining, and many mining engineers are currently involved in these activities. As we enter the decade of the 1990s activities in this category will increase, enhancing the relevance and utility of the material discussed. As the population increases, especially in metropolitan areas, the necessity to go underground will be greater. At the present time, not only are subsurface shopping malls and pedways connecting buildings becoming commonplace, but structures as diverse as the Civil and Mining Engineering Building on the University of Minnesota campus, a road-and-fleet maintenance facility in Multnomah County, OR, and even an ice cream parlor (Dairy Queen) in northern Wisconsin have been constructed underground. Placing utilities below the surface has numerous advantages and is now customary. Rapid transit and highways through tunnels in urban areas have been the norm for many years, but subterranean stormwater reservoirs, power plants, industrial warehouses, and food storage silos are relatively new innovations. The philosophy of underground defense installations is ancient, but their requirements and designs have trans-formed radically as technology advances. The use of under-ground space for disposition of wastes is modern, since it is recently that environmental concerns and waste disposal costs have assumed increased significance.

Jan 1, 2008

By J. E. Friant

The Mini-DiscTM cutter drill bit is a radical design departure from the traditional tri-cone rockdrill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-DiscTM drill bit, referred to as the “Disc Bit” has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory can not shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

The Department of Health and Human Services (HHS), National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), with the assistance of cooperating underground mining operations and state agencies, has conducted research exploring devices and technologies that could be used to assist miners navigating through smoke and dust resulting from a fire or explosion. Recent events in mines confirm that smoke and dust can enter and contaminate mine escapeways creating an atmosphere with severely reduced visibility. This reduced visibility results in substantially increased escape times, possible disorientation or confusion, and increased stress levels, and may prevent evacuation altogether. Tools or devices that assist miners in navigating through smoke-filled areas void of lifelines could make the difference in successful escape from the mine. This paper presents the results of OMSHR research to identify and evaluate tools and devices that could provide meaningful information to evacuating miners in areas with limited visibility and without the benefit of a lifeline.

Jan 1, 2011

By James McKelvey, Larry Drolet, Jason Swartz

INTRODUCTION When divers discovered that sections of a tunnel housing the pipeline that conveys wastewater from the Charleston Peninsula to the Plum Island Wastewater Treatment Facility had caved in, the Charleston Commissioners of Public Works(CPW) moved quickly to determine a long term solution for the city’s collection system, immediately focusing on the Ashley River sewer tunnel along the western boundary of the peninsula. Working with the Charleston community, as well as federal, state, and local officials, CPW developed a fast track yet long life design that can be used as a model for underground construction of tunnels in urban areas. The paper that follows summarizes key aspects of the Ashley River sewer tunnel project. HISTORICAL CHARLESTON Charleston, South Carolina is a culturally significant and historic city that was originally settled in 1670. There are over 100 buildings on the National Register of Historic Places within the Charleston area. Additionally, the first shots of the American Civil War were fired at Fort Sumter in the Charleston Harbor in 1861. As one can imagine, tourism generates significant business for the area with over 1.5 million people visiting Charleston each year. No project, especially one that requires digging, is done within the old city on the Charleston peninsula without careful planning. Many precautions are necessary to prevent damage or disruption to the historical properties. The Ashley River sewer tunnel project is exclusively in the old city. A lot of work was done during the design phase to minimize the impact to historical properties. Some of this work included: an archeological study (where pre-digs were monitored at all shaft sites by an archeologist); a building/structure assessment study (where structures near a shaft site were completely surveyed and cataloged); and an environmental study.

Jan 1, 2005

By Tae-kyeong Yeu, Cheon-Hong Min, Hyung-woo Kim, Sup Hong, Minuk Lee, Chang-Ho Lee

This paper concerns the optimum arrangement of the buoyancy module, which is used for stable dynamic motion and structure stability of the marine flexible riser. The main method of this study is simulation-based design using Genetic Algorithm (G.A) for optimum design and Multi-body dynamic for simulation. The marine riser connects the vessel and the seabed-tracked vehicle. The motion of the riser affects the motion of the vessel and the vehicle. In this study, a marine riser of the deep-seabed integrated mining system (Figure 1) is used. This riser has a strong effect on efficient transfer of minerals. So, the buoyancy module must be equipped to supplement problems of the structure stability and the dynamic motion. Positions and quantities of the equipping buoyancy modules are determined by the at sea experiment (Figure 2). But this method is not easy because the actual sea experiment is expensive, time-consuming and dangerous (Figure 3). Thus, the position and quantity must be determined by simulation-based design. The dynamic analysis models of the riser and the buoyancy module were built in the commercial software DAFUL. In the marine environment, factors affecting behavior are current, drag force, etc.

Sep 1, 2014

By Charles H. Wells

This paper describes a commercial installation of a sophisticated instrumentation and control system designed to maximize the performance of heavy medium cyclones. Samples of plant feed and its products were collected and analyzed for ash content so that measures of efficiency could be determined for plant operation under (1) manual control and (2) automatic (computer) control. The heavy medium cyclone control strategy and its digital computer implementation are discussed in detail. The sample results are analyzed and the economic benefits of automatic control are discussed. Results from the initial data sets quantify the economic benefits of automatic closed-loop control; viz, increased recovery and reduced clean coal variability have been clearly demonstrated.

Jan 1, 1981

PolyMet Mining is developing the NorthMet property near Duluth, Minnesota. Laboratory investigations had led to the development of the PLATSOL process to dissolve in one step the base metals (copper and nickel) as well as the gold and PGM’s. To complete the pre-feasibility study, a fully integrated ten-day pilot plant trial was undertaken, comprising of: high temperature (>220ºC) pressure oxidation in the presence of 5-10 g/L chloride (the PLATSOL process), followed by solid/liquid separation, gold plus PGM’s recovery from solution, conventional Cu SX/EW and recycling of the copper raffinate to the autoclave. The concentrate tested was a NorthMet bulk flotation concentrate assaying 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t Au, 2.2 g/t Pt and 9.9 g/t Pd. Laboratory results were fully confirmed and with minor adjustments of the laboratory PLATSOL® conditions, the following leach extractions were obtained during the pilot plant trial: Cu 99.6%, Ni 98.9%, Co 96%, Pd 94.6%, Pt 96% and Au 89.4%.

Jan 1, 2001

The Yanacocha Project is the first foreign investment in Peruvian mining since Cuajone (1976). Three years after the project began, it has become the largest producer of gold from heap leach operations in the world and the top producer in Latin America. The success of Minera Yanacocha (MYSA) opens a new chapter in Peruvian mining with the exploitation of its widely spread gold deposits and has attracted the interest of foreign investors in Peru's ample mineral resources. Construction began on August 1, 1992 and after twelve months of arduous work, the first gold bar was poured on August 7, 1993 from ore from the Carachugo mine. In 1993, Minera Yanacocha produced 81,000 ounces of gold and 304,000 ounces in 1994 (40% above budget). Production is expected to exceed 500,000 ounces in 1995 with the start-up of operations in the Maqui Maqui mine. This paper presents a summary of MYSA's experiences during its first two years of operations in the areas of mining, ore processing, environmental protection, loss control and community assistance. The paper also shows that MYSA's successes are not only due to the richness of the deposit, but also to the combination of a number of factors basic to the project's success, such as: an economic policy favoring investment in Peru, the availability of highly qualified local personnel to facilitate the transfer of technology from the United States and the desire and determination of the partners to carry the project forward in an initial atmosphere of uncertainty and terrorism.

Jan 1, 1996

By T. Shumka, M. J. Druckenmiller

"INTRODUCTION As we push further into the 21st century and closer to a more efficient mine, safety and operational enhancements are the two major keys towards attaining success. The Crusher Vision Automation System (CVAS) is a technological advance that will allow an operator to achieve higher safety and higher operational goals in the same piece of equipment. The CVAS is a patent pending system and method for measuring and maintaining the closed side setting (CSS) on gyratory crushers. In the same equipment and technology package, the CVAS will also allow safer placement of main shaft pieces for maintenance and replacement. This technology yields multiple uses and allows a site to significantly enhance safety and operational efficiencies. This measurement technique is used to provide more accurate data and faster data collection times than current techniques used today. It will give crusher operators accurate and reliable measurement for the CSS in a live, operating environment. Measurement data can be collected in five minutes allowing for fast adjustment of the mantle position and subsequent enhancement and streamlining of a crusher and downstream flowsheet. The advantage of this system is that it is permanently mounted at the crusher location, where the operator can turn the system on and off as many times as they like throughout the day with a goal of maintaining a constant CSS gap based on production and maintenance criteria to help streamline operations and enhance safety efficiencies.Regarding its other main functional area, mainshaft maintenance, it allows this work to be performed remotely while keeping personnel safer and out of harm’s way. SAFETY ENHANCEMENT The safety factor enhancement with this system is extreme. It does not require the use of overhead cranes, cleaning out the crusher, lowering people into the crusher or having the operator lower paint cans or lead balls into the crusher pocket while the crusher is in operation for measuring the setting. In order to perform the CSS measurements, the operator only needs to operate the laser through manipulation of a joystick while watching the video feed. Danger of a person falling into the crusher while trying to take measures is eliminated, as are the effects of handling lead balls and tracer dyes."

Jan 1, 2015

By Adrian Coombs, Paul Magowan, Derek Zoldy

Continued development and intensification are fuelling the urgent need for new trunk infrastructure within The Regional Municipality of York and throughout the Greater Toronto Area. Permitting of these projects is increasingly subject to public scrutiny to severely restrict dewatering through construction technologies and the requirement for a comprehensive and effective Environmental Management Plan. Three current projects: one on the York Durham Sewage System and two in the City of Toronto 1.Conventional Design, Tender, Award: 4,150m (13,600 ft.) 2.7m (9 ft.) finished interior diameter soft ground tunnel for York Region’s YDSS Interceptor Trunk Sewer 2.Negotiated Contract: 3,800m (12,500 ft.) 3.5m diameter (11.5 ft.) rock tunnels for Enwave’s environmentally sustainable and innovative chilled water system in downtown Toronto 3.Conventional Design, Tender, Award: 2,200m (7,200 ft.) 3.3m diameter (10.8 ft.) rock tunnel for reinforcement of Hydro One’s primary hydro feed in the downtown core of Toronto These projects exemplify issues such as: EPB tunnel and sealed shaft technologies Substantial permitting requirements associated with dewatering Mitigation of rock creep Congested downtown rights-of-way Deep shafts and confined working compounds Unique scheduling and cost benefits when Owner, Contractor and Consultant can work together cooperatively.

Jan 1, 2007

By Kexin Cai, Isidro Rivera, Shawna Von Stockhausen, Maria Chastka, Kevin Huynh

The Newell Creek Dam Inlet/Outlet Replacement Project is located approximately 11 miles north of Santa Cruz, California along Highway 9 in the San Lorenzo Valley. This project will replace the existing inlet/outlet works at the Loch Lomond Reservoir by constructing a tunnel using conventional excavation methods while simultaneously drilling three intake shafts to intercept the tunnel from within the city’s water supply. This project will improve the system’s overall operational efficiency and performance, and provide a safe and reliable facility for the City of Santa Cruz’s drinking water supply. This paper discusses the overall project configuration, construction observations, and challenges during construction, including tunnel excavating through the marine sedimentary siltstone of the Monterey Formation, probing and pre-excavation grouting, and the tools utilized to manage the project.

Dec 1, 2022

By P. Crouse, J. Obermeyer

"INTRODUCTION Site location and history The Holden Mine is a former underground copper mine that was developed and operated by the Howe Sound Mining Company (Howe Sound) from 1938 to 1957. The mine is located in north-central Washington State, U.S., near Lake Chelan in the area shown as Holden Village in Figure 1. Although Rio Tinto never owned or operated the mine, they are managing and funding a several hundred million dollar clean-up to prevent future water and soil contamination and to reclaim the former mine site under the United States Environmental Protection Agency (USEPA) Superfund process. The former mine included an onsite mill and a nearby housing complex for the miners. Howe Sound developed the mine as a series of near-horizontal drifts and tunnels, interspersed with stopes and shafts that connect different mine levels underground. The tunnels that were excavated to develop the mine total nearly 100 km in length.During development of the underground workings, Howe Sound removed more than 230,000 cubic meters (m3) of waste rock from the tunnels and deposited this material in two waste rock piles. Ore was processed from the mine in the onsite mill to produce a copper concentrate that was shipped off site for smelting. Roughly 10 million tonnes of tailings were produced as a by-product of the milling operation, most of which were deposited in three large impoundments (Tailings Piles 1, 2 and 3) directly south of and adjacent to Railroad Creek. Howe Sound closed the mine in 1957. In 1961, the property was transferred to Holden Village, Inc. (Holden Village), a not-for-profit corporation that maintains a year-round community and operates an interdenominational religious retreat in the former miners’ town. With the exception of the patented private land, the remainder of the Site is on National Forest lands and is administered by the U.S. Forest Service. The mine is remote. It is only accessible by boat or float plane from Chelan, Washington, up Lake Chelan to Lucerne, nearly 40 km. Vehicle access from Lucerne to the mine is provided through a 17.5-km-long winding gravel road that climbs 640 meters in elevation. The general site features are shown in Figure 2. Physical setting The Holden Mine is located on the eastern slopes of the Cascade Mountain Range at an elevation between 975 and 1,050 m above mean sea level. Holden Mine was developed adjacent to Railroad Creek, which lies in a glacial U-shaped valley carved into the igneous and metamorphic bedrock with steep-sided slopes (Figure 2)."

Jan 1, 2017

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By J. L. Ellenberger, T. Miller

"A limestone mine in Ohio has had roof instability problems that have led to massive roof falls extending to the surface. This paper describes a collaborative study of these events undertaken by the National Institute for Occupational Safety and Health and the mine owners. The study focuses on the roles that weak, moisture-sensitive floor and weak bands in pillars play in a general instability that led to roof falls at this mine. The NIOSH Stone Mine Pillar Design software (S-Pillar) does not include analysis for weak floor or weak bands and recommends that when such issues arise they should be investigated further using a more advanced analysis. It is important to recognize that without the impact of the floor or weak bands, the calculated inherent stability factor for these pillars is within the recommended design range. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to help determine the failure mechanism. Roof-to-floor extensometers were also installed in the areas predicted to have further instability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface. This recent case demonstrates that weak floor can be a significant factor in pillar stability and should be assessed during the design stage of the mine.To an area-wide failure (Zipf, 2001). In that case, it appears that the pillars had actually remained intact. However, moisture-related yield of the weak floor caused deformations which passed through pillars and into the roof, triggering roof collapse around the intact pillars (Esterhuizen et al., 2011). This previous case and the case presented in this study, while not identical, both demonstrate that weak floor and/or bands within pillars can be a significant factor leading to instability."

Jan 1, 2015