Search Documents

The Pogo Mine, near Delta Junction, Alaska is a 2500 TPD gold operation employing processes including grinding, gravity, rougher flotation, leach, CIP, and E/W. An OCS(Optimizing Control System) expert control system has been implemented on rougher flotation in early 2008. The OCS system communicates with the Plant DCS(Distributed Control System) through OPC(OLE for Process Control) communication. The initial strategy was to control the flotation cell froth level set points to achieve target froth velocities. This strategy was enhanced by controlling both level and air flow setpoints. The flotation cell air and level are adjusted to reach cell pulling rates (froth velocities). The pulling rate setpoints for each cell are determined based on downstream capacity (concentrate surge tank level). The effect of pH and upstream disturbances is also taken into account in adjusting the air and level setpoints. Feed forward compensation is employed down the flotation row to minimize disturbances.

Jan 1, 2009

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk either at concentrator commissioning, or at the point of implementing an improvement to an existing concentrator operation. High-Confidence Flotation Testing was developed for this purpose, and is part of the list of technologies of various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of practice and continuous improvement with this methodology at Xstrata Process Support, Sudbury, several improvements to this method and complementary connections into sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified.

Jan 1, 2009

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines completed a feasibility study for a new openpit gold mine in north central Nevada. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing openpit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled and unscheduled random events during the period under analysis.

Jan 1, 2007

By F. P. Schwarz

Even in an otherwise care-fully done sampling procedure, reducing subsample weight, or splitting, when the grain size of material is too large commonly generates significant error. Such error can be estimated from the standard deviation of differences between values of PAIRED ASSAYS. Samples from split-ting steps immediately before comminution, and showing a restricted range of grade, generate paired assays. Splitting steps characterized by relative standard deviations exceeding 16% generate nonrepresentative data. Such steps should be redesigned to optimize reliability of assay-dependent studies. A sampling scheme can be graphically characterized, and then redesigned as appropriate, using a SAMPLING NOMOGRAPH. Use of the nomograph avoids continued replication of assays. Generally at a splitting step, excessive error can be reduced by comminuting more material. Unnecessary effort can be mitigated by comminuting less finely and/or by splitting to a smaller weight.

Jan 1, 1992

By Leland E. Paulson

The Grand Forks Energy Research Center and Commonwealth Edison of Chicago jointly conducted tests in which 400 tons each of subbituminous coal and lignite were dried in a commercial scale dryer, oil sprayed and cooled, then shipped in open-top rail cars from Pekin, IL to Grand Forks, ND and stockpiled. Cars containing raw coal and dried coal that had not been oil sprayed were also transported for comparative purposes. The tests were conducted in August and November of 1974. The subbituminous coal was dried from 26 to 16 pct moisture and the heating value was upgraded from 8,420 to 9,650 Btu/lb. The lignite was dried from 39 to 22 pct moisture and its heating value was increased from 6,420 to 8,300 Btu/lb. Before loading subbituminous coal was cooled to 115° F and sprayed with oil at a rate of from 2 to 6 gal/ton. Similarly, lignite was cooled to 85° F and oil sprayed at rates of from 1 to 2 gal/ton. Both shipments arrived in Grand Forks with a minimum of difficulty. The subbituminous coal was subjected to 2 inches of rain during transit with no change in average moisture content. The cars containing dried and oil treated coal had less material lost to wind than either cars containing raw or untreated dried coal. With both dried lignite and subbitnminous shipments, a moderate increase in temperature was measured during transit. With the subbituminous shipments, ignition occurred near poorly fitted bottom dump doors, but was limited to a very small area. The dried lignite was shipped when ambient temperatures were below freezing, and frozen coal was noted around the edge of the car. At Grand Forks, the coal was stockpiled using proven techniques and has remained stable to this date.

Jan 1, 1975

By R. J. Sweigard

One possible alternative for disposal of flue gas desulfurization (FGD) by-products is use as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation of stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix proportioning of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48 percent and the peak stress could be decreased about 58 percent. The study indicates that fairly weak FGD materials can eventually lead to stability of backfilled highwall adits.

Jan 1, 1996

By Charles B. Dugger

Sacrificial linings for grinding mills have been a necessary state of the art of mineral dressing since the inception of comminution. Long recognized as the final link in energy transmission from power line to ore, mill liners as a scientific endeavor have not expanded as rapidly as other branches of mineral dressing engineering. Several reasons for this technological lag are apparent. Typically in the past, labor intensive foundries were freely located geographically, at a time when transportation charges made up a significant portion of the casting cost. Alloying agents had not gained their current level of sophistication and were relatively inexpensive in the quantities required. Precise foundry controls were not economically justified, or totally understood. Coincidental to these elements, liner consumption per unit processed did not categorically contribute as a major cost item to the mill operator. Grinding equipment was small, and many times lining life exceeded that of the promoter. These unique conditions no longer exist. Ore dressing equipment has grown to meet modern mining demands. Larger processing facilities, utilizing fewer pieces of equipment, have replaced operations of the past. Emphasis today and tomorrow is on larger and larger equipment, with an eye on lower and lower unit processing costs.

Jan 1, 1979

Federal regulations require the use of methane monitors on all mining machines. All machine-mounted methane monitors currently used in underground coal mines rely on catalytic heat of combustion sensors. As a comparison, although not currently approved for use on underground mining equipment, instruments with infrared sensors are evaluated in this study. Potential advantages of using infrared sensors include faster response time, long-term stability, and reduced maintenance needs. Tests conducted in the laboratory and at a full-scale model mine compare the performance of catalytic heat of combustion and infrared sensors operating under test conditions designed to simulate airflow conditions underground.

Jan 1, 2009

By MAHESH SHRIWAS, CHRISTOPHER PRITCHARD

Ventilation monitoring and control in mines are becoming an integral part of day-to-day activity for maintaining the health and safety of miners. This paper evaluates potential real-time monitoring solutions for detecting and reducing diesel particulate matter (DPM), mine fires and dust in situ and examines the state-of-the-art use of ventilation monitoring and control in underground mines for detecting and reducing air contaminants to acceptable regulatory limits. In this study, relevant documents, including research papers, trade publications and manufacturer website information, are reviewed to identify research gaps. This paper also includes evaluations of contemporary sensors (airflow, gas, dust and silica), control system and software technologies, data transport systems, the Industrial Internet of Things (IIoT), ventilation network simulators and control devices to identify potential health and safety research gaps. Examples of some mines in Canada, Australia and the United States that have been using ventilation monitoring and controls are included as well. Overall, this review identifies multiple challenges and research gaps in applying mine monitoring and control systems that could be the focus of future research, offering potential improvements to miner safety and health and financial benefits.

By T. M. Barczak

Stoppings are required to resist lateral forces on the face of the structure to control pressure differentials created by ventilating air. The design criteria in other parts of the world, including Australia, exceed this requirement by specifying over pressurization control to as much as 14 kPa (2 psi) in the active sections and 35 kPa (5 psi) in the main ventilating control areas. This is done to provide protection to the mine workers from explosive or air blast events within the mine that can create this over pressurization. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research to develop a new testing protocol for rating mine ventilation stoppings. The premise of this work is that arch-loading conditions more accurately reflects the transverse load capabilities of stoppings in underground coal mines than the freestanding flexural strength test specified in the current Code of Federal Regulations (CFR). This work clearly shows that the transverse load capabilities of dry-stacked, mine ventilation stoppings are dependent upon the material strength of the block and the height and thickness of the wall, none of which are part of the current CFR criteria based on ASTM E-72 specifications. This paper compares the transverse load capabilities of several block materials and wall dimensions commonly used in stopping constructions based upon simulated three-hinge, rigid-arch loading tests of half-wall constructions in the NIOSH Mine Roof Simulator. The results indicate a wide-range of transverse load capacities, ranging from as low as 21 kPa (0.3 psi) to as much as 117 kPa (17 psi) for the conditions evaluated in this study. The current CFR criteria do not distinguish between applications of these stopping designs despite their wide variance in transverse load capabilities, which is not conducive to employing ventilation control strategies that isolate certain sections of the mine to prevent injury to mine workers.

Jan 1, 2009

By S. Ersayin, I. Iwasaki

Application of a magnetic field was shown to be effective in controlling iron losses in pilot-scale cationic silica flotation in the processing of magnetic taconite concentrates. The design of a magnetic field distribution device and batch flotation test results using a 1.42m3 (50 cu. ft.) WEMCO cell are reported. Major losses of iron units in froth products were in the -25µm (500 mesh) fraction, and the application of a magnetic field decreased the flotation of fine magnetite, thereby improving the selectivity of separation. The “as received” sample was sufficiently magnetized and no further benefit was gained by magnetizing treatment. Selectivity was somewhat adversely affected by demagnetizing the sample, though its effect was minimal due to the magnetic field. The device is simple in construction, low cost and may be installed readily in existing equipment.

Jan 1, 2002

By I. J. Duckworth

Due to improved, stringent safety regulations, many modern road tunnels are statistically safer, per kilometer, than above ground roadways. However, the public perception and reaction in the event of a serious tunnel fire is very different to that associated with a surface incident. Vehicle fires in road and rail tunnels are recognized to represent an immediate and extreme danger to the patrons of those systems. Unlike workers in the mining and civil construction industries, the general public are neither trained nor equipped to fight fires or evacuate under deteriorating smoke conditions. Accordingly, for the majority of modern transportation tunnels the ventilation infrastructure is sized on the requirement to control the combustion products from worst-case fire scenarios and to provide a tenable evacuation route for the tunnel users. It is common for these same emergency ventilation systems to be employed, often in a reduced capacity, for other operating modes such as the dilution of pollutants during congested traffic conditions. This is one of the fundamental differences to mine ventilation, where primary ventilation systems are not typically sized based on fire scenarios. This paper presents an overview of the subject of fires in vehicular tunnels. This includes a brief history of major transportation tunnel fires followed by a discussion on the resulting legislation and standards that govern the design and operation of tunnel emergency ventilation systems. A summary is provided on the common criteria, theory, and design techniques that are employed during tunnel emergency ventilation systems design. Information is provided on fire detection and suppression, with a discussion on the growing acceptance of wet suppression as a means to mitigate major fires in road tunnels worldwide.

Jan 1, 2009

By D. R. Wilburn

This summary of international mineral exploration activities for the year 2005 draws upon available information from literature, industry and U.S. Geological Survey (USGS) specialists. It provides data on exploration budgets by global region and mineral commodity and identifies significant mineral discoveries and exploration target areas. It also discusses government programs affecting the mineral exploration industry and presents analysis of the mineral industry based on these data. Two types of information are reported and analyzed in this annual review of international exploration for the year 2005. They include budgetary statistics provided by Metals Economics Group (MEG) and information on regional and site-specific exploration activities in 2005 compiled by the USGS.

Jan 1, 2006

By Chaoxun Zhao, Daniel Tao, Craig Blue, Narendra B. Dahotre, Rick Honaker, Bhupendra K. Parekh, Hongyang Han

Equipment wear and corrosion have significant adverse impacts on the operating cost and efficiency of mineral processing plants. In this project advanced surface enhancement technologies are being investigated to decrease the wear and corrosion rate of metal surface. Enhanced metal surfaces are achieved through surface conversion, enrichment, and coating by use of advanced High-Density Infrared (HDI) and other technologies. Studies have been done to determine the effects of process parameters on surface properties and identify optimum conditions. The microstructure of the enhanced metal surfaces was characterized by SEM, EDS, and microindentation. Laboratory wear testing was carried out to investigate the wear performance and the viable coating candidate was determined.

Jan 1, 2005

By R. W. M. Lai

In flotation or hydrometallurgical leaching of minerals, the cumulative metals recovery for a given process condition generally approaches a maximum value or an asymptote as the process time increases. This paper discusses the experimental methods of identifying and obtaining the asymptote of metals recovery through kinetic studies. In flotation, the kinetic asymptote of metal recovery, or ultimate recovery, is a function of grinding and collector dosage, but within a realistic variable range, is not a function of pH or temperature. However, variations in grinding, collector dosage, pH and temperature, all exert noticeable effects on flotation kinetics. Frothers generally have a minor affect on the asymptote, but have a major affect on flotation kinetics. The asymptote from batch flotation is found to be identical to that of a continuous flotation. In hydrometallurgical Leaching, the asymptote of metal recovery for a given leaching system is a function of such variables as temperature, particle size, and acid concentration.

Jan 1, 1983

By Stig Eriksson

In Switzerland two major railway systems as shown below in Figure 1 has recently been completed or is under construction: ¦Lötschberg, south of Bern which was commissioned in 2007 ¦Gotthard, south of Zurich which is scheduled to be commissioned in 2016The aim is to increase the transport capacity of the railway system and to transfer more transport of goods to the railway by offering transport of trailers and lorries on the new railway systems. It will have a positive environmental impact but also improve the congested traffic situation of the highways in north-south directionThe Gotthard tunnel is totally 57 km (35 mile) long and the Lötschberg tunnel is 35 km (22 mile) long. Both tunnel systems consist of two parallel single track tunnels connected with cross tunnels at every 333 m (1 093 ft). Additionally there are cross-over tunnels and caverns for installations and operation. In the Lötschberg tunnel, the majority of the excavation has been by Drill & Blast and in Gotthard tunnel the major part is being excavated by TBM.

In the dimension stone industry, workers in processing shops may be exposed to harmful levels of respirable silica dust when conducting the different tasks in stone preparation, which include cutting, grinding, polishing, and thermaling. To protect workers from this health hazard, operators sometimes ventilate processing shops using fan-powered dust collectors to capture and filter dust. To investigate this issue, NIOSH, Pittsburgh Research Laboratory, in cooperation with a dimension stone operation, upgraded an off-the-shelf dust collector the operator was utilizing in a polishing/cutting shop. Initial dust surveys showed that the unit was under-designed for the amount of dust being generated in the shop. The objective of the research was to cost-effectively increase the air cleaning volume and improve dust capture efficiency of the unit with a larger motor and blower. The unit?s original stock 0.56 kw motor and blower was replaced with a 2.24 kw motor and matching blower to increase airflow. The unit was evaluated both in the laboratory and the shop before and after the retrofit to determine the improvement of the upgrade. The study showed that the 2.24 kw upgrade improved the performance over the original 0.56 kw motor resulting in more dust being cleaned from the ambient air in the shop. The 2.24 kw unit cleaned 19% more air and captured 32% more respirable dust than the 0.56 kw unit.

Jan 1, 2009

By K. W. Grubaugh

Indigenous people are nearly always affected when projects enter their territory. Crop and other asset compensation can help or undermine a project’s progress depending on the approach. When compensation is handled poorly, a technically viable project can get indefinitely entangled by local unrest. Stake holders associated with compensation issues include; the state, the indigenous people, non-governmental organizations, and the developer. Appreciation for the unique perspective of indigenous peoples and the influences affecting them can avert problems and prevent delays. A review of the compensation issues encountered in Ghana during its recent gold boom can assist in avoiding problems associated with handling poor and uneducated people.

Jan 1, 2002

By Steve Dubnewych

The Joint Water Pollution Control Plant, operated by the Sanitation Districts of Los Angeles County, treats wastewater generated by over three million people. A new tunnel and ocean outfall is being considered to meet future hydraulic demands and provide long-term redundancy for the Districts? existing tunnels, portions of which were constructed as early as the 1930s. The detailed process used to evaluate the feasibility of various tunnel and out-fall locations is described. Challenges include a geologic profile with mixed face and squeezing ground conditions; high water pressures; active fault crossings; gassy and contaminated ground conditions; and liquefaction, slope stability, and lateral spreading concerns in the area of the riser and diffusers.

By J. L. Carr

Every year, severe injuries and fatalities occur when a miner is struck or pinned by a continuous mining machine, shuttle car, scoop or other piece of mobile mining equipment. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Although hundreds of these systems are installed and in use in operating coal mines, the influence that coal has on the electromagnetic fields associated with these systems has never been rigorously quantified. NIOSH researchers have conducted tests to measure whether the proximity of coal has a significant influence on a popular design of proximity detection system. The system tested utilizes a low frequency magnetic field generator that would be mounted on the mining machine. At the NIOSH Safety Research Coal Mine in Pittsburgh, researchers measured the performance of a simplified proximity detection system of this type first on the surface then underground at varying distances from a coal face. Analysis of these measurements shows that the presence of coal does not have a measurable impact. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013