Search Documents

By J. T. Winkelmann

The Mineral Park Mine is an open pit copper-molybdenum mine located in northwestern Arizona, approximately twenty miles northwest of Kingman, Arizona. The concentrating facility has been regarded, with the expansion in 2011, as a plant capable of treating fifty thousand short tons of feed per day for the mixture of supergene and hypogene ores available. The grinding circuit consists of two 32? x 14? SAG mills and four 20? x 28? ball mills. As ores became harder with greater depth in the adjacent pit areas, however, the SAG mills became severely throughput limited. The traditional treatment for similar properties is the installation of a recycle pebble crushing circuit. Because the cost of such an installation is quite elevated, and preliminary testing and research was inconclusive regarding the predicted throughput increases, management and technical personnel set out to find another solution to the problem. The result entailed a redesign of SAG lifters/liners and a nearly unique circuit change which was, at best, a difficult step that defied current grinding logic. This paper describes these changes, events leading up to them, and the results.

Feb 23, 2014

By Donald J. Olson

The North 27th St. ISS Extension tunnel will, under present plans, be the last constructed section of Milwaukee Metropolitan Sewerage District?s (MMSD?s) existing deep tunnel system. The 6.5 m (21 ft) finished diameter tunnel is approximately 3,260 m (10,590 ft) long and is located in NE Milwaukee County. When disputes over the pro-cesses to be used in owner-directed pre-excavation grouting in rock threatened the completion date stipulated between MMSD and the State of Wisconsin, the MMSD and J.F. Shea, the contractor, entered into a unique agreement. Shea accepted responsibility for all shaft and tunnel grouting and water control during the project in exchange for settlement of claims related to grout quantities and perceived delays. This significantly reduced risk for the MMSD and helped ensure the stipulated completion of the project.

By Dennis D. Fischer

The second underground coal gasification experiment conducted by ERDA's Laramie Energy Research Center at a site near Hanna, Wyoming, was completed on July 30, 1976. During the experiment production reached 0.32 Mm 3/d (12 Mft3/d) of 6.9 MJ/m3 gas (175 Btu/ft 3 ). Approximately 6100 tonne (6700 ton) of coal were gasified during the experiment. Energy return ratios of 4.5 to 5.3, cold gas - thermal efficiencies of 76 to 89 percent, and overall process efficiencies of 65 to 74 percent were achieved during the second Hanna experiment. This paper describes the experiment and the results obtained with emphasis given to the determination of the energy recovered relative to energy consumed in conducting the test. Data from this determination are compared with previously published data from the first test conducted at Hanna during 1973-1974.

Jan 1, 1977

By Frank W. Schmechel

The subsidence monitoring program at the Old Ben No. 24 Mine was planned in 1976 as part of the on- going demonstration of longwall mining. The construction and installation of the network of surface subsidence monuments was started in Play of 1976 and completed four weeks later after which an initial reference survey was made of all surface monuments. Mining of the first longwall panel started in September of 1976 and was completed in May of 1977. Mining of the second panel started in August of 1977 and is continuing at this time. The Automatic Data Acquisition System (ADAS), which is the subject of this paper, was installed over the second panel on March 29, 1978 near the panel center (Figure 1) and approximately 104 meters (370 feet) in front of the face position at that time. Mine No. 24 is located approximately 5 kilometers (3 miles) Northwest of Benton, Franklin County, Illinois. Coal is being mined from the Illinois (Herrin) No. 6 seam which is at a depth of about 189 meters (620 feet) at the site. The Herrin No. 6 is up to 2.7 meters (9 feet) thick in the mine but a constant thickness of 2.1 meters (7 feet) is being mined by the demonstration longwall with both roof and floor coal being left for stability. Although the seam is flat laying at the mine, it dips north- ward regionally. Topographically, the surface over the demonstration panels is essentially flat and low laying with several areas of standing water. The Rend Lake Dam (United States Army Corps of Engineers) is about 305 meters (1000 feet) north of the demonstration site.

Jan 1, 1979

By Kevin Andrews, Zach Agioutantis

Analysis of Coal Pillar Stability (ACPS) software, released in 2018, integrates numerous empirical pillar design techniques. The ACPS program incorporates methodologies originally available as design tools from the National Institute for Occupational Safety & Health (NIOSH), including Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Analysis of Multiple Seam Stability (AMSS), and concepts including Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar formula, and pressure arch loading. The design methodologies that are the basis of ACPS were developed via analysis of significant amounts of real-world data and have been standards of the United States coal industry for decades. While there are empirical factors built into ACPS, making it ideal for use in U.S. coalfields, the concepts in the program have proven to be applicable in variable mine settings, and the software was developed to allow for user-based, site-specific modifications of key design inputs. Application of ACPS to cases outside the regions for which it was developed must be approached carefully, and continuous development of site-specific data is mandatory. A case study is presented involving the application of ACPS to assess pillar stability and assist future design for an underground lignite mine in Eastern Europe. Assessment of in-mine observations, review of the geology of the lignite mine, and evaluation of specific conditions associated with a failure event resulted in “calibration” of key input factors to ACPS. Scenarios evaluated with ACPS suggest that pillar strength and overburden depth are key factors for the determination of pillar stability and design in future areas.

Jun 25, 2024

By Jinke Li, Fenghua Wang

"While coal fueling China's economic growth it has already been causing severe pollution and amounts of CO2 emission. How to make deep reductions in carbon emission is not only a huge challenge for the greatest consumer of coal, but also a revolution for China’s coal industry. The paper explores how to shrink CO2 emissions during the lifetime of coal. The paper points out that increase of coal mine efficiency and productivity, green mining, utilization of coal mine methane and environment-friendly disposal of coal gangue can reduce CO2 during coal mining; coal preparation and coal by wire can decrease CO2 during coal preparation and transportation; improving combustion efficiency, CO2 capture and storage (CCS) and coal transformation can lessen CO2 during coal utilization. The paper also points out that Circular Economy Park is a practical way to develop a low carbon economy for coal industry. An econometric model for total coal industry and each sector are constructed to measure carbon emissions based on CO2 equivalent emissions, then with detailed calculations, based on potential greenhouse-gas emission's reduction, a most likely low carbon roadmap of China's coal industry is depicted with scenario analysis method.Introduction Global warming poses a profound threat to humanity and the natural world and is one of the most serious challenges humankind has ever faced. According to the 2007 Fourth Assessment Report by the Intergovernmental Panel on Climate Change (IPCC), global surface temperature increased 273.89 ± 273.33K during the 20th century (IPCC 2007). Increasing concentrations of greenhouse gases have caused most of the observed temperature increase since the middle of the 20th century (United States National Academy of Sciences 2008), and CO2 is the most important cause of global warming. In 2005, CO2 contributed 76% of global greenhouse gas emissions, CH4 contributed approximately 16%, N2O contributed approximately 6% and the combined F-gases contributed approximately 2% (IEA 2010). Among the many human activities that produce greenhouse gases, energy use is by far the largest source of emissions. Since 1870, CO2 emissions from fuel combustion have risen exponentially (IEA 2009). Of the three types of fossil fuels - coal, natural gas and petroleum - coal constituted only a quarter of the world total primary energy consumption in 2007. The situation is even more critical in China than in the rest of the world, as energy-intensive industrial production is growing rapidly, and large coal reserves exist in combination with limited reserves of other energy sources. The development and production of the coal industry provide stability in China's economic growth. There are more than 7000 coal enterprises in China; the coal enterprises are the main contributor to China's ""economic miracle""."

Jan 1, 2017

By A. G. Yapo, T. W. Camm

"Mining plays a key role in the development of modern civilization as a source of essential raw materials and provider of essential fuels, producer of jobs and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer now than before as companies understand better their work environment and the importance of mining responsibly.A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production.An attempt to bring light and clarity to the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers, through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the all-in sustaining cost (AISC) and all-in cost (AIC).Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact, the high gross margin (sales minus cash costs) has been promoted in past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $61/g ($1,900/oz) in August 2011, gold producers were not reporting excessive profits in their cash flow/income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits.The disconnect led to a need for more accurate cost reporting in order to win back investor confidence and provide better understanding of gold mining economics. In 2012, the senior gold mining companies, including Gold Fields, Barrick Gold Corp. and Newmont Mining Corp., worked with the WGC to develop a new measure. This resulted in the June 2013 publication of the new framework AISC and AIC, which has been widely embraced by the sector since Jan. 1, 2014 (WGC, 2013).The adoption of the new cost template would have the dilemma of showing the real profitability of gold mine properties, which might alleviate taxes from governments and legislators, but it might also scare off investors toward more lucrative industries if not winning back their confidence."

Jan 9, 2017

By Robert Schnab

ASFINAG is responsible for the construction and operation of the Austrian highway system. It is approx. 2,400 km of highways and 65 tunnels with a total length of 200 km including the Tauern Tunnel. In order to improve the documentation of the tunnel construction, ASFINAG chose to use a state of the art tunnel scanning system to record the various stages of construction: excavation, initial shotcrete lining, smoothing layer and final cast in place concrete lining. The geometric and photogrammetric documentation is provided on a daily basis to all par-ties involved. This innovative concept provides accurate & complete information in real time. The tunnel scanner documentation of the 2nd tube at the 6.4 km long Tauern Tunnel will be presented in this paper as a part of the survey contract.

By d&apos, L. R. Fletcher, Andrea. D. V., M. A. Peltier

The Bureau of Mines analyzed coal mine blasting accident data obtained from the Mine Safety and Health Administration (MSHA), U.S. Department of Labor. The data were examined to determine the causes, frequency, and severity of accidents in an effort to point out the most dangerous aspects of coal mine blasting. Accident data for the 14 years from 1971 through 1984 show that there has been a total of 43 fatal and 926 nonfatal blasting accident victims in surface and under- ground coal mining. This is an average of 3.1 fatal and 66.1 non- fatal injuries each year. Underground coal mining accounted for 60.5% of the fatal and 78.7% of the nonfatal accidents involving explosives and breaking agents in coal mining. In addition, since 1970 there have been 53 fatal and 20 nonfatal injuries that occurred when explosives were the ignition source for dust and/or methane explosions in underground mines. Abstracts from 297 accidents that occurred from 1978 through 1984 were also examined to determine accident causes. Most accidents occur during scheduled blasting, and failure of the blast area security system is the leading cause. Blast area security problems in surface mining are failure to clear the blast zone, failure of personnel to follow instructions, inadequate guarding, and failure to retreat to a safe location and/or take adequate cover. Other common causes in surface mining include premature blasts, excessive flyrock, and misfires. In addition to the above causes, accidents in underground coal mining can be due to rockfalls triggered by the blast, unexpected breakthroughs, fumes, and incidents associated with Airdox-type systems.

Jan 1, 1986

By Carl Pinches

Underground or surface mining is only the first stage in the ore mining process. Once the ore is mined, it is transported to the surface for further processing. Generally, this is done to extract the particular metal or other component of the ore that has commercial value in its purified form. In its raw state, there are typically between 4 and 7 g/t (0.12 and 0.2 oz/st) of valuable material from rock mined. Once on the surface, the ore is crushed and milled in order to obtain smaller rock particles and to expose the minerals that contain the desired metal or component. Mixing the milled ore with water, a process known as ?froth flotation,? can be employed. This technique consists of a series of tanks, or ?cells? through which the process liquid flows. To obtain the maximum recovery, the milling and flotation process will often be repeated a second time. An increase between 100 and 1,000 g/t (2.9 and 29 oz/st) of rock following this stage of the process is typical. Efficient recovery is key to maintaining a profitable mining operation. The measurement and control of the froth flotation process is vital.

Jan 1, 2010

By M. Karmis

The determination of the surface area which may be impacted by underground mining is an important consideration in subsidence engineering. A number of parameters have been utilized to identify this influence area, most notably the angles of draw and break. This paper discusses the implications of selecting an appropriate "damage angle" for defining a potential damage area due to mining, within which surface structures may be impacted Furthermore, the influence of both mining and geological factors, such as mining width and depth and overburden lithology, on this angle is examined, using the Surface Deformation Prediction System (S.D.P.S) software. Finally, recommendations are given for applying these concepts in subsidence control.

Jan 1, 1994

By MYRIAM FRANCOEUR, JOHN R.R. BOWLING, ADAM MCFADDEN

As duct-fan systems push the envelope of power, length and cost, their design calls for a more comprehensive technoeconomic analysis to ensure they deliver the expected results without failure and cost overrun. This work explores the numerous factors to include in the design of an extensive (semi-)rigid duct-fan system. Besides delivering a given airflow, the system must satisfy component limitations and power constraints during its lifetime. We evaluate the assumptions underlying the positioning of in-line booster fans in a long gapless duct-fan system and propose a strategy for specifying the location and blade pitch of successive booster fans to prevent system failure due to a partial vacuum.

Oct 1, 2022

By F. E. du Plessis, P. De Waal

Through the development of innovative in-line mineral quantification sensors, the possibility has arisen to apply modern control theory to implement automatic process control for electrostatic high tension (“HT”) roll separators. A pilot-scale set-up was constructed to enable continuous tests to be carried out. A typical dry mill feed was continuously pre-heated and separated with a modern lab scale HT roll machine. The mineralogy as well as mass-flow of the non-conductor stream was quantified in-line, and the combined streams were re-circulated in an endless loop by a combination of vibration feeders and a bucket elevator. A fractional factorial experiment was executed to determine the most significant control parameters of the HT roll separator. Then a multi-input, multi-output dynamic model of the HT electrostatic separator was extracted by the application of standard system identification techniques for automatic control. The most important control variable to ensure a stable product grade could be identified. This allowed a robust single-input, single-output controller to be implemented. The process variable and set-point was mineral grade and the control variable was electrode voltage. Roll speed was manually adjusted while the mineral grade was kept on set-point by the control system. The roll speed, where maximum mass flow and therefore maximum yield was produced on-grade, could therefore be rapidly determined. Atmosphere humidity and ore temperature served as disturbances. Some other adjustable parameters were kept constant during the experiments, namely feed mineralogy, splitter settings and feed rate. Delivery of maximum yield, with a controlled grade, can improve production while reducing the burden of complex manual tuning. Manual tuning previously involved coping with multiple parameters with uncertain cross coupling influences on the end result. Even the end result was typically only known after completion of mineral assays. Automatic grade stabilisation and yield optimisation for a HT roll separator bank requires in-line measurement of mineralogy and mass flow, as well as the implementation of a robust process control system.

Jan 1, 2005

When the Middle Ages were drawing to an end and Rotterdam, then still a small fishing port, began to extend its trade relations to continental ports handling general cargo, a development was initiated which was to give Rotterdam a predominant position in maritime traffic in Europe 300 years later. Despite many setbacks and the silting up of the mouths of the Rhine and Meuse rivers, the port experienced a new rise towards the end of the previous century after the dunes at Hook of Holland had been cut through as planned by Dutch engineer Caland. With its favourable location in the mouth area of the Rhine and a hinterland opened up by waterways it was merely a matter of the city council pursuing a far-sighted policy to make the best of these natural advantages. Thus new port installations were erected on the southern bank of the Meuse in the first quarter of this century, which were expanded in the course of the subsequent decades. The New Waterway became the main artery for industrial enterprises, in particular oil industries, which sprang up along its banks (picture 1). Whereas 30 years ago Rotterdam's Waalhaven, with its new jettees for general cargo and mainly bulk goods, was still one of the most modern terminals, the growing size of ships, which increased by leaps and bounds for tankers, in particular towards the end of the 'fifties, necessitated much larger harbour facilities built further and further towards deep water.

Jan 1, 1972

By J. W. Hawkins, K. B. C. Brady, K. Miller, J. Cuddeback

Remining of abandoned coal mines in Pennsylvania requires the implementation of pollution abatement and mining techniques called Best Management Practices (BMPs). Water-quality data from over 100 remining sites with more than 230 abandoned discharges were analyzed with respect to the types of BMPs employed to abate the pollution loadings of acidity, iron, manganese, aluminum and sulfate. Discharges exhibiting a significant decrease in acidity were most highly associated with sites where large volumes of alkaline materials were encountered (66.7%) or added (63.7%). The best results for iron loading were achieved with large-quantity alkaline addition (54.6%) and water handling systems (47.8%). Water handling systems (47.4%), daylighting (40.7%), and revegetation (40.2%) were associated with significantly lower manganese loadings. The decreases in acidity and sulfate loads associated with increasing the amount of alkaline material in the backfill indicates that the production of acid mine drainage can be retarded by adding large quantities of alkaline materials.

Jan 1, 2002

By Steve J. Czehura

The Butte quartz monzonite is the host rock for early porphyry copper style mineralization and subsequent mesothermal-epithermal, enargite-gold style veining that transects the district. The east-west Anaconda system veins sustained mining for over a century. They include the Emma, Anaconda-Original, Syndicate, Badger-State and Alice-Rainbow veins, each with strike lengths of more than 3,660-m (12,000-ft) and vertical continuity in excess of 1,370-m (4,500-ft) with mining widths from 1.5- to 15-m (5- to 50-ft). These characteristics are unique to Butte. The incredible dimensions and tenor of these veins have yet to be surpassed and Butte is still touted as being the “Richest Hill on Earth.” The Anaconda Company was formed in 1895 to develop underground copper reserves in the district. It eventually consolidated all operations under one company. Production from underground mining continued through the mid-1970s. Openpit mining in the Berkeley pit began in 1955 with the extraction of supergene ores, along with the remnants of deeper horsetail zones inaccessible to the underground mines.

Jan 1, 2006

By T. Bui

The shut-off value for a panel cave mine determines when a draw point will be shut-off and mining will cease from that draw point. Using a shut-off value strategy for a panel cave mine is similar to using a cut-off value strategy for an open-pit mine. This paper will discuss how to choose an appropriate shut-off value strategy that an engineer can use when planning a panel cave mine to increase the net present value (NPV) of the project. Using a shut-off value equal to the mining and processing cost will provide the total mining reserves for a panel cave mine given a specified footprint. When the net present value analysis method is used to compare one design to another then using a shut-off value greater than the mining and processing cost will generate a higher NPV. This strategy will replace the marginal ore at the top of a draw column with higher grade ore at the bottom of newly opened draw points. A draw column is broken material which sits above a draw point and it is mined to a specified height above the draw point. This height is called the height of draw (HOD). Varying the shut-off value over the life of the mine can increase the NPV even further. This strategy would have a high shut-off value during the early stages of a mine and low shut-off value during the later stages. If the shut-off value is too high then too many tonnes would be left behind the draw point and the overall value of the mine will be decreased. Also with a high shut-off value then the production target may not be maintained due to too many draw points closing too soon.

Feb 23, 2014

By Alafara A. Baba, Yakubu A. Dallatu, Kehinde I. Omoniyi, Shemang Y. Chindo, Edith B. Agbaji

With the rise in global demand for pure copper, there is an urgent need to consider the processing of low-grade chalcopyrite ores. Ammoniacal leaching solutions have been reported as effective and efficient leachants for the dissolution of chalcopyrite. This work reports on different parameters that influence the leaching kinetics of a Nigerian chalcopyrite-rich siderite ore obtained from the Wase local government area of Plateau state, Nigeria, and assayed as 11.30 weight percent copper.

May 1, 2023

By Staff

GENERAL DESCRIPTION The Lucky Friday mine is located in Mullan, Sho-¬shone County, Idaho. The mining method is horizontal slice cut-and-fill (with timbering for support or un¬timbered) using hydraulic sand. Cemented sand fill at a 1:17 ratio is used in sill pours and at a 1:7 ratio for the final 152 mm (6 in.) capping in successive stope floor pours. Annual production with 100% cut-and-fill mining is 167 829 t (185,000 st). The average depth of mining is 1296 m (4250 ft) and the average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size The ore body is 396 to 488 m (1300 to 1600 ft) long on strike, 1421 m (4660 ft) on dip, with an average width of 2.3 m (7.5 ft). Dip varies from vertical to1.2 rad (70°) Ground Conditions, Ore Value, and Production Requirements The ore body contains quite strong argentiferous galena and quartz. The hanging wall and footwall are strongly sheared and fractured. Ore value is $211/t ($192/st).

Jan 1, 1982

By Jr. Chesson

"Phosphate" is a misnomer as often used. The word is increasingly used to refer to any material containing phosphorus - an element essential to any form of life. Phosphate rock, a mineral - fluorapitate - is recovered from Florida's sedimentary deposits in particle sires ranging from 0.1 to 13.0 millimeter. This product of mining, washing, screening, and flotation is commonly called "phosphate". Its phosphorus content, measured and reported as P2O5, varies from 29% to 35%, and is essentially insoluble. "Phosphate" is also used to describe products containing soluble phosphorus obtained from acidulation of phosphate rock with mineral acids; primarily, sulfuric acid. Many miners have nearby chemical plants wherein phosphate rock is converted into upgraded products such as phosphoric acid, superphosohates, and ammonium phosphates with 45% to 70% P205, soluble and suitable for use as fertilizer. The rock and upgraded products are all commonly called "phosphate"; the plants, "phosphate plants' and the producers collectively are known as the "phosphate industry". The public in Central Florida generally loses identification of the individual operators that include major corporations such as IMC. Williams Companies, W.R. Grace, Mobil, Embark, U.S. Steel, Borden, American Cyanamid and others. They all become just a "phosphate company".

Jan 1, 1978