Search Documents

By T. S. Golosinski

Typical dragline rigging includes several sets of ropes: hoist ropes, drag ropes, dump ropes and boom suspension ropes. The drag and hoist ropes contribute most to the dragline operating cost, and significantly influence dragline productive time. Both work in very difficult conditions and wear out rapidly. As a result frequent rope changes are required at a substantial cost and time loss to the operation. Although performance of rigging has a profound impact on dragline performance, there are no industry-wide standards related to its selection, operation and maintenance. Little information on the subject is available and the practice differs widely throughout the industry. The life of drag and hoist ropes depends on: (1) rope construction, which should closely match requirements of the specific application, (2) correct definition and application of the rope discard criteria, so that full advantage of the rope can be taken without endangering safety of operation, and (3) rope operating conditions and its maintenance. The study presented in this paper was intended to address the above points, based on a survey and assessment of the present industry practice.

Jan 1, 1993

By R. S. Olsen

Intensely altered rock has had a large effect on slope stability as slopes increase in height at Island Copper mine. Traditionally used, fracture-controlled rock slope stability design techniques have been supplemented with analyses of failure modes which include failure along curved surfaces typical of soil materials. A rock mass rating (Pa) system has been developed that addresses the lower end of rock mass strengths. Rock masses are rated in terms of fabric integrity, alteration, fracturing intensity and gouge strength. Rock mass classes have been defined using statistical frequency distributions of rock mass rating values. Strength values have been assigned to the various classes from shear testing, back analyses of failures and engineering judgment.

Jan 1, 1987

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries to be developed in recent years Minera Peñasquito, S.A. de C.V., a wholly owned subsidiary of Goldcorp Inc. has developed the Peñasquito property to produce an average annual production of 120 kilo tonnes of lead containing 0.5 million oz gold and 30 million oz silver and 250 kilo tonnes of zinc containing 20 thousand oz gold and 1.5 million oz silver.. The Peñasquito property covers a 39,000 hectare area in the western half of the Concepción del Oro district in the northeast corner of Zacatecas State, Mexico, approximately 24°45'N latitude/101°30'W longitude. The sulfide reserves are 1,009 million tonnes containing 3.33 million tonnes of lead, 7.26 million tonnes of zinc, 16.5 million ounces of gold and 1,000 million ounces of silver. This paper describes the work to justify the installation of HPGR to process the crushed SAG mill pebbles. The SAG mill-Ball mill and Cone crusher (SABC) grinding circuit is an accepted grinding circuit to optimize power consumption relative to throughput. The installation of a HPGR to process the Cone crusher product is the next step in optimizing the power consumption relative to throughput. The concern expressed by some on not moving on this change in grinding circuit was the capital and operating cost of a HPGR. The pebbles from the SAG mill can be the more abrasive and are the harder particles of the ore. Goldcorp investigated the wear and processing costs of installing a HPGR to treat the crushed pebbles. The conclusion was the installation would be a very positive economic factor in the operation of Peñasquito. This is the first application of the use of HPGR to process crushed pebbles. Minera Peñasquito and M3 Engineering selected Polysius to provide a Polycom 2417 with twin 3,000 kW drives. A comprehensive test program at Polysius has shown for 7% higher circuit power it is possible to get approx 23% higher tonnage. This coupled with full utilization of the SAG and Ball Mill available energies and with proper control of the transfer size from the SAG to Ball mill circuit there is the potential to achieve 65,000 mtpd per line or a 30% total capacity increase. The cost of power for this increase in grinding capacity is 4.8 kWh/tonne.

Jan 1, 2010

By DEBASHISH MISHRA, SOMU MANDAL, ASFAR MOBIN KHAN, JAI KRISHNA PANDEY, NIROJ KUMAR MOHALIK, SANTOSH KUMAR RAY

Coal is a low-cost fuel with high calorific value. Statistically, the global coal mining industry suffered 12,489 fatalities in 104 reported mining accidents from coal dust explosions during 1900 to 2020. This review article discusses the occurrence, mechanism and explosibility parameters of coal dust explosions and presents a literature survey of the laboratory and computational fluid dynamics (CFD) simulation methods of studying them, as well as a comparison of the two methods.

Feb 1, 2023

By H. E. M. N. Moursy, Hassan El-Shall, M. N. Ahmad, Ponisseril Somasundaran, C. R. Holland, D. Chandler, G. Walker, Regis Stana, Patrick Zhang

The reaction kinetics of the acidulation of Moroccan phosphate rock (32% P?05) using 45% nitric acid were investigated using the Shrinking Core Model (SCM) , a newly developed Diffusion Model (DM) and a newly developed Combined Reaction and Diffusion Model (CRDM). This was achieved buy conducting a number of experiments in a controlled batch reactor system at different temperatures. The conversion and the reaction rate were calculated at different time intervals. The SCM based on reaction time and the CRDM characterize the acidulation process of phosphate rock. Diffusion of nitric acid and the products of acidulation at the early stages of reaction through the phosphate rock were found to be the rate-controlling step, resulting in a dif- fusion coefficient, which controls the mass transfer process. The reaction kinetics were found to fit first-order kinetics especially during early stages of reaction time. The deviation of the kinetics from first-order at later stages was due to the fact that the overall reaction was mass transfer controlled with respect to nitric acid and products diffusion.

Jan 1, 2002

By Paul C. Miclea

In case of a major fire in a tunnel between stations or ventilation shafts, if the buoyancy effect of the hot gasses is stronger than the airflow induced by the fans, the risk of backlayering could restrict the safe evacuation of people. Obstructions in the tunnel and alternate airflow paths can further reduce the air velocities past the fire. Currently there are two computer programs available to address the issue of underground fires: o "Subway Environment Simulation" (SES), Version 3.0, developed by Associated Engineers, a Joint Venture of Parsons Brinckerhoff Quade & Douglas, Inc., De Leuw Cather & Co., and Kaiser Engineers, Inc. for the U.S. Department of Transportation o "MFIRE", Version 1.26, developed at Michigan Technological University for the U.S. Department of the Interior, Bureau of Mines. As implied by its name, the SES program was developed specifically for the analysis of subway ventilation systems. It can be used to analyze the heat released into, and removed from, a subway or vehicular tunnel and to determine the effect of ventilation elements on airflows throughout the network of stations or other merging tunnels. It has a special feature allowing the user to predict the effects of a fire at any location within the subway system. Version 3.0 of the SES program is designed to be used with a "critical velocity" calculation in order to determine whether or not tunnel airflows can be controlled during a train fire emergency. The original version of the program was written in FORTRAN for mainframe computers, such as the IBM 4381. Recently ICF Kaiser Engineers has compiled a version of the SES program for PC use. The MFIRE program simulates the interdependence between a mine ventilation system, with its pertinent fans and structures, and changes in ambient conditions or a source of heat, such as a fire. It also accounts for natural ventilation. The program is written in FORTRAN 77 and compiled for 8086/8088 based microprocessors, allowing it to be run on an IBM PC or compatible computer with a 2.0 or a later version of DOS, 256K random access memory (RAM), and a text editor. This paper reports the comparative results of an application of both programs for the same network in a recent study.

Jan 1, 1991

By J. G. Asbury

Broadly conceived, the demand for electricity depends upon three sets of variables: (i) the growths of the many individual demands for energy services; (ii) the competitiveness of electrically driven technologies in meeting these demands; and (iii) the energy-conversion efficiencies of installed electrical technologies. The first set of variables establishes the size of the potential market; the second, the market penetration of electrical equipment; and the third, the quantity of electricity required to operate the equipment. All forecasts of electricity consumption ultimately depend upon inferred or assumed relationships to describe the future behavior of these variables. This partitioning of the demand-forecasting problem is conceptually useful and will guide the discussion presented in this paper. However, it is also something of an oversimplification. Examined in more detail, the electricity fore-casting problem is exceedingly complex. The variables mentioned above are, in turn, found to depend upon more fundamental sets of demographic technological, resource, and policy variables. The demand projections developed by the major forecasting services are usually developed in terms of these underlying variables, which themselves must be independently forecast.

Jan 1, 1985

By William C. Howe

This paper describes the technical status of the atmospheric pressure fluidized bed combustion (AFBC) process for utility steam generation. Major areas where AFBC development work is needed are discussed. Various approaches to solving these key issues are identified and the ongoing research and development programs addressing the key development areas are described. Other significant programs pertaining to the development of AFBC for utility steam generation are also discussed and needs for future work identified.

Jan 1, 1978

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a longwall installation roadway (faceroad) design methodology that could be utilized by suitably qualified colliery personnel. This goal was achieved in 2012 and the design methodology (and software package) is referred to as Analysis and Design of Faceroad Roof Support (ADFRS). The intended benefits to underground operations, in the provision of this information and resource, are a safer and more productive workplace.

By BERND SCHÖNHERR, JÖRG DEHNERT, PETER WINDISCH, JENS STOPP

The Quick-Erect Stopping System (QESS) offers a new way of reducing the radon exposure of miners in Germany, especially during remediation work in old mines. The QESS is a lightweight, modular and reusable construction kit of interlocking telescopic aluminum tubes, radon-proof foil and expanding foam. It is designed to seal off radon-rich parts of galleries within minutes. Originally, the QESS was developed to protect miners against radon exposure. Then, the QESS found the attention of several mine rescue teams at a German mining conference. Some mine rescue drills by The Student Mine Rescue of the Technical University Bergakademie Freiberg, Wismut Mine Rescue and Front Range Mine Rescue helped to improve the system and highlighted its potential for mine rescue operations. Now, the QESS is well-suited for small-scale mining. The QESS can be used to both protect miners from radon exposure and to support mine rescue operations. Moreover, the QESS was also successfully used in ventilation experiments.

By B. T. Mirabile, D. Tang, Y. Luo, S. S. Peng, C. T. Holland

Knowledge of local coal mine roof geology is critical to the design of a safe and suitable mine structure. An automated drill control and data collection system has been designed for a J.H. Fletcher twin-head roof bolter. Drilling parameters collected during the drilling process can be used to interpret geologic features intercepted in the mine roof. The drill and data collection system have been tested in both laboratory and underground settings. Visualization of certain drilling data has shown good correlation with geology drilled. A quantitative prediction model was developed using drilling parameters examined with data visualization. The quantitative model was tested using laboratory drilling data.

Jan 1, 2004

By K. E. Hjelmstad

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air, rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine, fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage.

Jan 1, 1989

By J. Noll, E. Cauda, T. Barone, S. Vanderslice

Measuring diesel particulate matter (DPM) for underground metal/nonmetal mine compliance samples is done by collecting DPM onto quartz fiber filters and analyzing the samples via NIOSH method 5040 for elemental carbon (EC) and total carbon (TC). As part of the sampling train, two quartz fiber filters in tandem are housed inside an SKC DPM cassette that includes an impactor. The impactor segregates DPM and mine dust, and the second filter is used to correct for adsorption of vapor phase organic carbon (OC). Since the value of the second filter is subtracted from the first, the pre-existing carbon on the filter media for both filters needs to be comparable. In addition, the pre-existing carbon on the media should be low for accurate and sensitive results. However, there have been some reports of elevated OC on the filter media of the SKC DPM cassettes, which would cause the limit of detection (LOD) to be higher than reported at times. In this study, blank SKC DPM cassettes from different batches and with different expiration dates were analyzed to quantify the amount of carbon on the filter media and to determine the LOD and limit of quantification (LOQ) associated with these samplers. It was found that the organic carbon and total carbon on the media was about five times higher than quartz media used in samplers from other studies. The average TC on the blanks was 2.57 μg/cm2 with a standard deviation of 0.70, resulting in a LOD of 21 μg/m3 TC, 8-hr Time Weighted Average (TWA), and LOQ of 69 μg/m3 TC, 8-hr TWA, when using these samplers for collecting DPM. The LOD and LOQ may be improved through some sample preparation techniques. INTRODUCTION Exposure to diesel exhaust (DE) is associated with an increased risk for lung cancer and other adverse health effects (Attfield et al. 2012, Silverman et al. 2012, Ping and Guang 2017, IARC 2012). Pronk et al. 2009 reported that the highest exposed groups to elemental carbon (EC) from DE worked in underground sites in mining and construction and they were exposed to concentrations between 27–658 μg/m3. At concentrations (1–25 μg/m3 EC) well below those observed in mining, diesel particulate matter (DPM) exposures were estimated to increase the risk of cancer by levels exceeding those typically acceptable for occupational risk in the United States and Europe (Vermeulen et al. 2014). This suggests that underground miners are especially at risk because of their more substantial exposures in confined working spaces. As a protective measure, in 2001, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/nonmetal underground miners to DPM to an 8-hr time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, 2006).

Jan 1, 2019

By L. Zhou, L. Yuan, R. A. Thomas, D. Bahrami

The abstract emphasizes the importance of a calibrated ventilation network model for mine ventilation planning, optimization, and fire simulation. It highlights the impact of continuous airflow monitoring on improving model calibration. The paper discusses an experimental study at the Safety Research Coal Mine (SRCM) to understand the use of continuous airflow data for model improvement. It also addresses practical problems in calibration and tuning using this data, including analysis of air velocity sensor fluctuations and application of sensor location correction factors for accurate average air velocity.

Mar 7, 2022

By G. E. Erdman

This paper presents talc milling guided by a theme of "So You Want to Be In The Talc Business". Such a theme strikes a cautionary note to warn the uninitiated of potential pitfalls, and this paper will cover briefly some of the technical traps as well as one of the larger talc milling operations. It is important to our purpose to pre- sent some of the market and mineral complications that make the business of producing and selling industrial talcs much more intricate than an outsider would perceive. Metal markets by comparison are great worldwide pools into which production streams of generally identical metals can flow over a weir of market prices. Industrial talc markets are not as well defined and often must be developed by the producer working closely with a specific customer or groups of customers to prove out the attributes of the specific product from a new property. All the negatives of a new market seem to work against the introductory talc in the forms of industry or customer reluctance to change, sales prices, cost of delivery, mode of transportation, health considerations of the minerals and many more. Just locating the potential customers for a new industrial talc may be a substantial undertaking. Thus, an analogy of the worldwide metal market might compare starting a new talc operation to trying to gather up enough fallen rain drops to be able to start a production stream of a worthwhile size.

Jan 1, 1984

By R. Kramer, A. Habibi

A ventilation survey was conducted in an underground longwall trona mine. The mine is relatively shallow and categorized as a gassy mine. The ventilation system includes three intake and six exhaust shafts, and three surface axial fans ventilate the mine in a blowing configuration. Airflow quantity, pressure losses and air psychrometric characteristics were quantified, and the influence of moving cages and skips in the shaft examined. The benefits of utilizing high-accuracy digital pressure transducers and advanced psychrometers were seen when undertaking a “leapfrogging” survey to gather data needed to build a computer ventilation model. Two underground booster fans with VFDs are idle but available at the mine. The ventilation model was used to determine the optimal booster fan locations to decrease operating cost by reducing the load carried by the main fans. A leakage study was conducted to evaluate the effects on the system of additional pressure from a booster fan. The study finally prepares a future ventilation model for the next 15 years of mine operation and investigates the effect of proposed scenarios.

Jan 1, 2014

The mining industry, like most other industries, has had a difficult couple of years. What are your thoughts on the industry?s direction in the next few years? I am bullish on our industry. There is no question in my mind that the quality of life we enjoy today is largely a result of our past successes in the minerals and mining sector. I am equally certain that the sustainability of that quality of life and the aspirations of the rest of the world to attain that same level of lifestyle will depend hugely on our future successes and will be the driver for our industry to continue to excel and prosper. Surely, there are going to be challenges along the way. These challenges are not only from the public, regulators and various governing bodies, but also from our industry?s own self regulating efforts. However, we have demonstrated throughout the past several decades that we have the capability to meet these challenges head on and come out ahead.

Jan 3, 2010

By C. J. Bise, P. Bucks

Central Appalachian coal reserves are a valuable natural resource in high demand, both domestically and internationally, justifying efforts to increase percentage recovery through pillaring. Unfortunately, the challenge associated with pillar extraction introduces additional safety risks during the activity. Although pillaring developed prior to mechanized mining, current technology and mining practices have made this form of mining highly modernized. However, current fatality trends suggest that work still needs to be done to control the residual risk that is not controlled by modern practices, such as those having a personnel-performance-based component. This paper investigates the application of modern coal pillaring techniques and will present a risk-management-based strategy that targets personnel-performance-based risk, in order to improve the ability of safety engineers, managers and trainers to provide training programs addressing the needs of pillaring sections.

Jan 1, 2012

By James R. Taylor

24.1-BASIC PRINCIPLES JAMES R. TAYLOR The basic principle involved in maintenance is protection of a company's investment through the care and upkeep of machinery and equipment, buildings and properties. Maintenance is justified through making available to the maximum extent possible the facilities, machines and services required by the operating and production departments in their function of insuring optimum return on investment. As the size, cost and complexity of the equipment used in modern mining and related industries increase, operating and production personnel become proportionately more dependent upon maintenance engineering for its contribution to the overall profit picture. A greater part of the total cost now is charged to maintenance and the maintenance group becomes a major company unit. Basic maintenance concepts have changed very little over the years, but the advances in methods and technique have brought about tremendous challenge and have in consequence assumed a greater influence and importance. The older "sledge- hammer" methods have given way to engineered and scientific systems, while the accelerating development of intricate equipment and machinery, and the instrumentation essential for control, demand an ever-increasing upgrading of maintenance personnel. Regardless of this growth in importance, cost and complexity of the maintenance function, it is important to remember that it is not an independent and self-sufficient unit, but is a necessary facet of the entire plant operation and is subject to the company's total production effort. As one part of a team, maintenance is successful only when functioning cooperatively wit11 the other departments it serves Close collaboration in all areas served by n maintenance group is essential if it is to function fully to protect the company's investment, whether the assets are in machinery, materials or people. 24.1.1-MAINTENANCE SCOPE Maintenance functions may be grouped into the two general classifications of primary and secondary. This grouping constitutes a basic division although, in practice, the scope of the maintenance activity varies in each mine or plant and is subject to differences in size and type of operations and company policy, plus the influence of precedent, which may be sectional or industry-wide. The primary functions supply the justification for the maintenance engineering department. while secondary functions are variable according to plant conditions and needs. The primary functions may be categorized as follows: 1. Maintenance of existing machinery and equipment. 2. Maintenance of existing buildings and grounds. 3. Inspection and lubrication of equipment and machinery. 4. Utilities generation and distribution. 5. Alterations to existing equipment and facilities. 6. Installation of new equipment and facilities. 7. Instrumentation.

Jan 1, 1973

Once every three years the eyes of the construction and mining industry?s turn to Munich, Germany for the bauma trade fair and exhibition. From April 19-25, Messe München International (MMI) will host the 29th edition of this massive show that, despite the recent recession and global financial struggles, has grown yet again. The show, which is completely booked, will take place on a record 555,000 m2 (5.9 million sq ft) of indoor and outdoor exhibition space at the New Munich Trade Fair Centre. More than 3,000 exhibitors are expected to make use of this event. To prepare for the show that highlights some of the largest and most impressive construction and mining equipment in the world, Messe München began working months in advance on getting the infrastructure on the open-air site ready, in time for the arrival of the gigantic machinery exhibits, which started to arrive in March. Part of the preparations include a new entrance at the northwest corner of the exhibition center that was built to regulate visitor flow better. This should help with bauma considering that in 2007 more than 500,000 visitors passed through the gates. ?Although in 2010 the construction machinery sector in many markets worldwide will be recovering only slowly from the recession, we are pleased to report that we are seeing strong demand for exhibition space. This shows that exhibitors regard participation in the world?s leading trade fair bauma as a must, although many are at present having to make cuts in their advertising and trade-fair budgets. We have been particularly surprised by the strong demand for space from exhibitors from markets like China, India and Turkey. The fair is fully booked and many more companies are on the waiting list,? said Eugen Egetenmeir, managing director of Messe München. More than 50 percent of the exhibitors at bauma 2010 come from countries outside of Germany. While the show?s primary focus is on the construction section, it is not as if the mining sector will be difficult to find. With some of the largest equipment in world on display in section C2 (Fig. 1), the mining industry is sure to be well-represented.

Jan 4, 2010