Search Documents

By Charles A. Beasley

Increased technical and legislative analysis by all parties of interest could result in more efficientand better directed regulatory legislation in the mining industry. Efforts to forestall or frustrate legislation through massive lobbying and public relations efforts are seldom effective over time and often lead to more stringent and far reaching legislation than necessary. The Federal Coal Mine Health and Safety Act of 1969 is perhaps an outstanding example of such insufficiences; a future example may well be regulatory surface mine legislation. Although a lack of extensive hard data seldom enables rapid or sophisticated analysis early in the legislative process, even preliminary analysis may be sufficient. Simple statistical analyses of available data, assessment of the legislative rationale, and subjective appraisal of other non-quantifiable constraints to improved mine safety. An average of 115 underground fatalities at an exposure frequency rate of 0.67 can be reasonably expected in the immediate future, under existing levels of technology, degree of regulation, and economic conditions. If gross unrefined estimates of 6 preparation plant, 5 surface, and 30 strip mining fatalities are assumed, the total fatality industry level could be expected to approximate 156 Serious professional, economic, and technical constraints within the the industry probably preclude any major decrease of these accident levels within the near future

Jan 1, 1972

By Frank F. Rahne

Butler Taconite, operated by the Hanna Mining Company, is an Iron ore pelletizing operation that is located on the Western end of the Mesabi Iron Range in Northeastern Minnesota. The operation mines low-grade taconite ore and through primary crushing, two stage grinding, magnetic separation, agglomerating and indurating, produces 2.6 million annual tons of high quality, 66% iron pellets. Mining and stripping is done with 13 - M100 trucks and 5 - 12 cu. yd. shovels. The operating processes in the concentrator and pellet plant are primarily con¬trolled through a centralized control room and monitored by a PDP l140 computer. During 1969 and 1970, a re-organization of the Company took place. Through this re-organization, each mine unit was analyzed and studied to determine the proper staffing of the internal departments. At this time, it was decided to continue with further detailed studies of the Maintenance Department with the intent to reduce maintenance costs. Maintenance costs at the time of the re-organization were 38.6% of the total mine operating cost. The preliminary study indicated that the Maintenance Department had a system of maintenance, as a matter of fact, it had a separate system in each sub-maintenance division and in some of the sub-divisions each foreman had a system of his own. Therefore, from the data collected, it was decided to develop one system of maintenance that could be utilized throughout the entire operation. To determine the type of system suitable to all phases of the operation, detailed time and method studies were conducted. All types of maintenance tasks performed at the operation were studied. The data collected was analyzed and the recommended improved methods were reviewed with the Maintenance Superintendent and his staff. The new improved methods that were accepted as feasible, were introduced into the system immediately.

Jan 1, 1975

By Lukas Erkurt, Wolfgang Holzer, Stefan Auderer, Richard Gradnik

SEM/ NATM Tunnelling contracts in Austria and Germany are usually tendered applying unit price contracts. The purpose of this paper is to show how contractual problems are resolved in these countries. The focus will be put on describing the theoretical approach, several case studies will show how contractual problems were dealt with on site.

Jun 23, 2024

By Arthur L. Raub

During the last decade, there haven't been any great innovations in the design features of a copper concentrator. What has worked well in the past continues to work well, so that major breakthroughs have been minimal. Conservatism in the ranks also plays an important part. As a copper concentrator is not designed and built everyday, Davy was elated to have an important part in this project. This is the story of the design of the oracle Ridge Project located north of Tucson on the back of Mt. Lemmon at an elevation of 5,900 feet on the N.E. slope of the Catalinas. The Oracle Ridge property, formerly known as the Control Mine, is owned by Oracle Ridge Mining Partners, a joint venture between Continental Materials Corp. of Chicago and Union Miniere of Brussels, Belgium; both or¬ganizations specializing in the non-ferrous metal industry.

Jan 1, 1979

By E. J. Onuscheck

Coal mine safety of the past was plagued by disasters that took the lives of thousands of miners. Through the years new mining methods, improved laws, and a commitment from the mining industry has reduced the frequency of such incidents to a minimum. History tells us that coal was mined in the early 1700's in Virginia primarily for use by blacksmiths -- most of that mining was done in the Richmond area. It was in those mines that methane was encountered; as workings became more extensive, methane explosions became more frequent. In the early 1800's the first recorded explosion occurred near Richmond, Virginia -- 40 men were killed.

Jan 1, 1985

By J. W. Walkiewicz

The U.S. Bureau of Mines has conducted studies using microwave energy to stress-crack iron ores. In a microwave chamber which simulates a continuous throughput operation, the Bond grindability of a taconite sample was improved by 13 pct at a bulk temperature of 197? C. To further improve the economics of microwave fracturing, higher powers up to 16 kW were used to rapidly heat samples to relatively low temperatures in a continuous belt-fed applicator. A significant enhancement of grindability was obtained with a minus 1.9-cm taconite rod mill feed. At a sample temperature of 130? C, the grindability was improved a maximum of 26.1 pct over the non-microwaved sample.

Jan 1, 1993

By C. N. Greene

I am sure it is obvious to all of you that a complete program of casualty and property insurance is as necessary for any tunneling contractor as it is for anyone else involved in trade in the United States today. Going beyond those general undefined terms, there are many areas that need specific attention, particularly for contractors, regardless of size. WORKERS' COMPENSATION Workers' Compensation is mandatory in all states and the District of Columbia. In most of the states, private insurance provides this coverage. In a few states, the state operates Workers' Compensation funds, some of which are competitive with the private sector and others are operated on a monopolistic basis. Under a monopolistic setup, you have no choice, you must buy coverage from the state. Self insurance of the Workers' Compensation risk is also an alternative in most jurisdictions. With a contractor operating only in the U.S., the coverage extensions are few in number. If your work brings you anywhere near navigable waterways or land extensions thereof, you should have both U. S. Longshoreman and Harborworkers' coverage, as well as Employer's Liability coverage for the master or members of the crew of a vessel.

Jan 1, 1983

By K. Chandrasekaran

Carbon-in-leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. The CIL process is becoming attractive even in other situations when preg robbing is not a factor. This article discusses the situations in which the CIL circuit can be applied. The results of leach-carbon-in-pulp (CIP) and CIL circuits at Newmont Gold's Mill No. 2, No. 4 and No. 5 are presented for comparison: Mill No. 4 was initially designed for a throughput of 4.1 kt/d (4500 stpd). It is presently operating at an average throughput of 6.6 kt/d (7300 stpd) without significant changes to the original design. The design considerations of the Mill No. 4 CIL circuit are discussed. The design of any processing facility represents a series of decisions. The final design options should ultimately be resolved based on economic as well as technical considerations. Every design decision represents some sort of compromise. From the designer's view point, these decisions are made with the conviction that the final product represents the most prudent long-term expenditure. The design throughput rate is a decision reflecting a maximum return for the capital and operating costs that the plant will incur over the life of the mineral resource. The result is a plant that is not operator proof or maintenance free because it would be too costly to build. At some point, the incremental increase in the level of capital expenditure would not adequately compensate for the lower

Jan 1, 1991

By Thomas A. Boyce

Introduction Although innovative coal extraction technology can be approached from many angles, this paper focuses on three: innovation in response to rising costs, to changing mining conditions, and to regulatory issues. Before exploring these three subjects, however, a basic question needs to be raised. Why Innovation? Coal is widely heralded, and quite correctly so, as the United States' "ace in the hole." It has been said that the U.S. is to coal what the Arabs are to oil. The implication is that we have nearly inexhaustible reserves - that coal is cheap, plentiful, and easy to extract. Indeed, because our current productive capacity is estimated to be 15-20% greater than demand, we have been given a false sense of security about the ease of future coal extraction. Therefore, innovative measures are being concentrated on developing technologies for the demand side of coal, including power generation, synthetic fuels, and industrial applications. What is often forgotten is that the unit cost of producing energy from these new technologies depends critically on the cost of the coal feedstock -in some cases the coal consumed accounts for more than one-third the total cost. Thus, while the developers of the end-use technologies struggle to improve the overall thermal efficiency of their process by one or two per¬centage points to make the energy produced competitive in the marketplace, they often are unaware of the risk of a 3 to 6% increase in coal costs wiping out the expensive, hard-earned results of their research. Energy planners are just beginning to realize that coal is not a uniform commodity available at low cost in infinite quantities. Coal is a heterogeneous material whose cost and quality vary widely with local conditions. To produce the massive amounts of projected coal-based energy at reasonable costs, we urgently need devel¬opments in extraction technology, as well as in end-use technology. Thus, coal extraction, coal conversion and utilization, and end -use energy consumption must be viewed as highly interdependent parts of an energy supply network (Fig. 1). And current emphasis on conversion and utilization must be balanced by more emphasis on upstream technologies, including coal extraction. Even more important, the impacts of innovation (or the lack thereof) in any one technology area in the energy supply network need to be discussed and understood by those working in each of the other areas. Why innovation in coal ex¬traction technology? Figuratively, we are all in the "coal boat" together - geologists, miners, transporters, processors, power producers, distributors, and consumers. Innovation is required from each of these sectors to overcome the obstacles that prevent greater use of our most abundant national energy resource. All other links in the coal energy supply network depend on large volumes of coal produced at reasonable costs. Declines in productivity, therefore, must be reversed; the more difficult mining conditions that will be encountered call for new methods and equipment, and regulatory issues must be resolved if the coal ex¬traction link is to be a strength rather than a weakness in the planned U.S. transition to an economy based more on coal and less on imported petroleum. Innovation Tailored to Regional Conditions Once the importance and urgency of innovative coal extraction technology has been grasped, the next step - implementing a research program - becomes quite

Jan 1, 1980

By W. Szymanski

The United States contains one of the world's largest reserves of uranium. Domestic production and exploration activities, however, have declined since the early 1980s due to weaker-than-expected growth in nuclear power demand and to foreign competition. The main result has been that more costly and less productive conventional mines and mills have closed. Meanwhile, industry productivity as measured by uranium output per employee has increased threefold since 1980. At the end of 1992, only six plants, all nonconventional, were operating in the United States. Due to cost considerations and increased environmental awareness, any additions to existing capacity are expected to be met through nonconventional in situ leach plants.

Jan 1, 1994

By C. W. Lockhart

Strength evaluation programs, based on sub- jecting a number of 5-718 inch (0.15 m) diameter core samples from highly fractured or poorly consolidated rock, to triaxial compression tests, have been successfully completed. An innovative approach was required since con- ventional methods with similar materials had not produced reliable results. Drilling methods were modified, and specially designed transparent core barrels were used. Sample preparation was successfully accomplished by using speciallydesignedtools and unorthodox hand- ling methods. Initial tests were carried out on weathered oxides from an open pit copper mine. The technique was later used successfully where the test material was weak, friable coal. The procedures used offer a practical method of testing weak materials where conventional methods would not be successful.

Jan 1, 1980

"What is your history and how did you get involved in mining?Like many SME members, I came from a mining community with a family history in mining, in my case Walkerville, MT. Both of my grandfathers were underground miners. My father was a miner for a short time. He later sold drinks to the miners. Unfathomable by today’s standards, my dad would pick up the miners’ checks at the pay office and have them cashed and waiting with a shot and beer for the miners when their shift ended. My mother was a nurse, who from time to time, would patch up an unfortunate miner. I remember walking past multiple picket lines on the way to and from grade school, watching homes being boarded-up. I grew up with a deep respect for the critical relationship between labor and management.I had no intention of going into mining and initially set out to pursue a career in chemical engineering. But I attended my first two years of engineering at Montana Tech, due to the proximity and affordability. This is where I met Dr. Tom Finch, a mining professor who taught statics to the engineering students. After a coaching session in a hallway, half way through my sophomore year, I switched to mineral processing engineering. In his colorful way, Professor Finch advised me that, “You do not want to make #@*!! erasers and #@*!! Jell-O the rest of your life go talk to the guys in mineral processing.” He was very persuasive and here I am today.How about your involvement with SME?I encountered SME out of school and a little later in my career. Terry Maio and Jim Arnold invited me to local section meetings in the Missouri Lead Belt. That was my first exposure to the technical programming and relationship building that was possible at the local level. After Ozark Lead shut down and I relocated to Nevada, Rich Johnson, Scott Barr and Dave Collins encouraged me to attend my first annual meeting in Salt Lake City, UT. I joined SME at that time and was fortunate to be engaged by members like Art Schweizer and Jim Arnold, and I soon began the leadership progression for the Mineral & Metallurgical Processing Division. Since then, I have supported SME at the national and the local level serving in multiple roles and capacities."

Mar 1, 2017

By O. Tranbarger

In aging tunnels, wall and roof deterioration can eventually result in defects that must be detected and repaired to maintain safe structural conditions. In investigating tunnel defect conditions, a specialized FM radar system was developed with a programmable VHF and UHF operating sweep range for optimizing the penetration and measurement capabilities. The new FM radar technology was tested in two aging brick-lined tunnels in New York City. Test results showed that FM radar signals could penetrate eight courses of water-saturated brick and that the original steel liner outside the tunnel walls was intact.

Jan 1, 1985

By Ehsan Moradabadi, Debra F. Laefer

"To more rigorously address tunneling risks to above-ground structures, vulnerability evaluation of all structures along a tunnel route is required. This multi-block area along the route can be considered a district. To fully assess each structure within a tunnel’s zone of influence, a multi-block or district-level model may provide new insights as to risk evaluation and mitigation strategies. However populating such a model with the existing geometry of the built environment poses a major challenge as measured drawings are not readily available for all structures along a tunnel’s route. Cost-effective population of such a model could arguably involve remote sensing data in the form of laser scanning or photogramme-try. However even for unreinforced masonry structures, where external, above-ground geometries can be captured, without a prohibitively expensive building-by-building, in person survey many factors would remain unknown. To consider these uncertainties in an automatic way, a performance assess-ment framework is proposed. Such a framework allows a more rigorous, initial, risk quantification than is currently possible within the simple empirical models generally being used in industry when tunneling risk is initially assessed. This paper introduces (within the allowable space limits of this format) consider-ations for auto-population and application of a district-level, tunnel-risk screening tool. INTRODUCTION Challenging topography, intense urbanization and infrastructure development, combined with limited land availability and a growing awareness of environmental issues have lead to increasing usage of un-derground spaces to control aboveground traffic and provide essential services in metropolitan areas. Tunneling, however, is not without its own risks, especially with respect to aboveground structures whether it be widespread minor damage (Burland et al. 2001) or the more notable, although less fre-quent, large-scale collapses such as the 2003 Shanghai (Allianz 2015) or 2004 Singapore (Magnus et al. 2005) events."

Jan 1, 2016

By Frank Florez

INTRODUCTION The Magma mine, located at Superior, AZ, some 100 km (60 miles) east of Phoenix, was discovered in 1875, and was originally mined for silver. The property was acquired by W. B. Thompson who formed the Magma Copper Co. in 1910. Prior to 1965, square-set mining and cut-and-fill methods were used to mine steeply dipping veins at Magma. Ore was moved to the chute by gravity in the square-set stopes and by slusher in the cut-and-fill stopes. The stopes were gobbed with waste from the surface and development headings in the mine. The original square-set method of mining was modi¬fied in order to extract replacement ore bodies in limestones that dipped at 0.52 rad (30°) and varied in thick¬ness from 4.6 to 38 m (15 to 125 ft). Mining of these ore bodies was done by starting at the upper lateral ex¬tremities and retreating to the access openings. The timber square sets and cribbing were used as temporary support, the ground being allowed to cave as the mining retreated. It was found, however, that mining in such a manner was very inefficient; safety hazards increased be¬cause of the blocky and fractured characteristics of the ore and the weakness of the hanging wall. GENERAL DESCRIPTION The undercut-and-fill method of mining is now the primary stoping method used at Magma, and no pillars are left for later extraction. Four ore bodies are pres¬ently being mined. These ore bodies (see Fig. 1) dip conformably at 0.52 rad (30°) to the east with the host limestone and shale sediments, their average strike length is about 122 m (400 ft), and their thickness varies from 9 to 38 m (30 to 125 ft). The ore bodies are separated by varying thicknesses of barren rock. Three of them come together at various elevations primarily in the area of the main feeder fault, but there is an apparent horizontal displacement of about 23 m (75 ft) on the main feeder fault which complicates stope layout. The method as originally applied has been modified in order to mine more efficiently ore bodies that are 9 m (30 ft) or more in thickness. The modification was made to mine all the ore at a given elevation before dropping down for the cut below. The advantage of this is that mining is done on a horizontal plane and there¬fore muck removal can be mechanized. Also multiple faces are made available, thereby improving overall min¬ing efficiency. Another major change made was to carry a 6.7-m (22-ft) face when mining the top sill and a 6.4-m (21-ft) face when mining under fill rather than the former standard 3.35-m (11-ft) high face. This change lengthens the mining cycle and cuts mat prepa¬ration costs in half. Stopes are laid out (see Fig. 2) so that maximum mining panels are available and yet one stope crew will not tie up too much of the ore reserve. One stope might consist of as many as 20 panels, and these panels are divided evenly on opposite sides of the extraction cross¬cut. The stope layout is planned so that the maximum tramming distance to the orepass will not exceed 30.5 m (100 ft) on the crosscut and 38 m (125 ft) in the panel. Stope panel distances are sometimes exceeded when min¬ing to the extremity of the ore body. Tramming distance limits are determined by the efficiency of the com

Jan 1, 1982

By E. F. Schnitzer

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries -Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014

By J. R. Patts, A. B. Cecala, E. J. Haas

Exposure to respirable crystalline silica (RCS) remains a serious health hazard to the U.S. mining workforce who are potentially exposed to RCS [1,2] as various ore bodies are drilled, blasted, hauled by truck, crushed, screened/sized and transported to their destinations. To examine a method for assessing RCS exposure using a NIOSH-developed video exposure monitoring (VEM) technology (referred to as Helmet-CAM), video and respirable dust concentration data were collected on 80 miners across seven unique mining sites. The data were then collated and partitioned using a thresholding scheme to determine exposures that were in excess of 10 times the mean exposure for that worker. Focusing on these short-duration, high-magnitude exposures can provide insight into implementing controls and interventions that can dramatically lower the employee’s overall average exposure. In 19 of the 80 cases analyzed, it was found that exposure could be significantly lowered by 20 percent or more by reducing exposures that occur during just 10 minutes of work per eight-hour shift. This approach provides a method to quickly analyze and determine which activities are creating the greatest health concerns. In most cases, once identified, focused control technologies or behavioral modifications can be applied to those tasks.

By M. Stephen Enders

The Little Rocky Mountains host epithermal gold-silver bearing vein and stockwork deposits in a syenite intrusive complex. Pegasus Gold Ltd. is currently mining the oxidized deposits by open-pit methods and recovering gold and silver by heap-leach processes. A geologic program has been designed to effectively determine the basic ore characteristics; 1)mineralization; 2)oxidation; 3)structural setting; 4)lithology; 5)alteration; and ultimately, 6)the leachability of the ore. Geologic mapping, sampling, drilling, assaying, and testing are routinely used in exploration, development, production control, mine planning, and ore reserve estimations. Timely and accurate assay results are essential for the program's success.

Jan 1, 1983

By G. H. Thomas, M. C. O’Riordan, S. Rae

INTRODUCTION The British mining industry comprises 228 nationalised coal mines producing some 113 million tonnes of deep mined coal and employing 242,600 persons of whom 185,200 work below ground. There are in addition 174 small privately-owned coal mines employing 1500 persons underground and producing 1.5 million tones of coal. In the non-coal sector there are 108 privately-owned mines producing some 20 different minerals, including tin, wolfram, fluorspar, potash, rock salt, china clay, ball clay and fireclay. There are currently 4,100 persons employed in these mines of whom 2,346 are employed below ground. One mine producing potash employs 870 persons of whom 465 are underground workers. Since 1975 all matters relating to the health and safety of persons at work and of the general public who are exposed to industrial hazards have come within the purview of the Health and Safety Executive (HSE). The Mines and Quarries Inspectorate (MQI) is a constituent part of that organisation and enforces legislation applicable to all mines and quarries. The National Radiological Protection Board (NRPB) is a statutory and independent body that was established in 1970 to advance knowledge and provide information and advice about radiological protection. The NRPB has an agency agreement with HSE to provide advice and services relating to radiological protection, including protection against exposure to radon decay products in mines. There are as yet no statutory requirements controlling exposure to this source of radiation in Britain. Investigations for the presence of radon in British coal mines were begun in the mid 195Os. The concentrations found were of low order, typically around 2 pCi/l (Duggan et al., 1968). This was not surprising since big coal mines are well ventilated to control methane and airborne dust and it is now generally accepted that radon and its decay products do not constitute a health hazard in British coal mines. At one or two small mines where igneous intrusions were in close proximity to the coal workings, slightly higher readings were recorded. The MQI then commissioned NRPB to make investigations at metalliferous mines and in these much higher readings were detected. It was later agreed that the NRPB should undertake a survey of all non-coal mines in Britain to establish the extent of the problem. This survey was conducted mainly in 1973, (Strong et al.,1975) and follow-up surveys at various mines have since been conducted by the MQI. These investigations revealed that radon readings could be high in mines producing tin, haematite and fluorspar. Some small mines working other minerals in the same localities also showed high readings. More recently owners have been making environmental measurements at mines where there was some cause for concern. LEGISLATION AND RADIATION STANDARDS As a result of the survey work for MQI the Board in 1975 recommended an occupational limit of 4 WLM in a year from radon decay products together with a programme of radiological supervision (Strong et al., 1975). The MQI accepted the recommendation and advised employers and employees that the 4 WLM limit should be adopted. The limit corresponds to a concentration of 0.3 WL, equivalent to 30 pCi/l of radon-222 in equilibrium with the decay products, and was in accordance with an earlier recommendation by the International Commission on Radiological Protection (ICRP, 1959). ICRP recommendations are usually endorsed in Britain. It was recognised that some years would probably be required to achieve general compliance, and this is proving to be the case. Some confusion has been caused in Britain by the conflict between successive Euratom Directives on this and other standards of safety. As relative newcomers to the Community, we were not affected by earlier Directives, but the situation is different now. In 1959, the Commission of the European Communities provisionally recommended a maximum permissible concentration for radon-222 and daughters of 3 x 10-7 µCi/cm3, which corresponds to 300 pCi/l (CEC, 1959). The number was affirmed in 1962 (CEC, 1962) and reaffirmed in 1966 (CEC, 1966) but without any specification of the state of equilibrium. In 1976, the CEC again recommended 300 pCi/l, but on this occasion, the daughters were assumed to be present in the same quantities as in unfiltered air (CEC, 1976): this implies 40 WLM a year in poorly-ventilated mines. The formula is repeated in the latest version of the Directive (CEC, 1980), but the value is now said to be an interim one because it might not ensure compliance with the appropriate dose limit. ICRP (1955) recommended 300 pCi/l in equilibrium with the decay products in 1955 and reduced this value to 30 pCi/l for unfiltered air in 1959 (ICRP, 1959), endorsed it for equilibrium conditions in 1976 (ICRP, 1976), and held to it until 1980: these values imply respectively 40 and 4 WLM a year. The recent recommendation of the ICRP (1980) that the annual limit of intake for the decay products should be 0.02 J in a year corresponds to 5 WLM, but there is a rider that reduction should be made for exposure to gamma rays and long-lived airborne radioactivity. An allowance of 20% is suggested for uranium mines, implying 4 WLM a year for the decay products. The

Jan 1, 1981