Search Documents

By Matthew T. Mowry

As the mining industry continues to hire young professionals to supplant the growing number of retirees, a well-developed engineering curriculum, coupled with practical, real-world training, can prepare mining engineering graduates to make meaningful contributions in the industry. Successful companies can be measured not only by their reserve base and annual production but also by their retention of mining engineering graduates with zero to five years of operational experience. My personal experience in the industry during the last five years has been varied and rewarding. The knowledge and experience I have gained have taught me valuable lessons that prepared me for my current role.

Nov 1, 2013

By R. A. Basse, W. D. Diment, A. J. Petrina

INTRODUCTION In 1957, diamond drilling on a magnetic anomaly indicated an extensive zone of copper mineralization on what is now the Craigmont Mines property. By mid¬1958, drilling established a copper ore body. Milling commenced in September 1961 at 4536 t/d (5000 stpd) and by the end of October 1977 the mine had produced 339 662.04 t (374,363.9 st) of copper. At present, two-thirds of the mill feed is derived from underground operations and one-third from low-grade surface stockpiles. Craigmont Mines is situated 209 km (130 air miles) northeast of Vancouver (see Fig. 1), 16 km (10 miles) west of the town of Merritt, a logging, ranching, and mining community of about 7000 people. It is serviced by paved highways, Canadian Pacific Railway, British Columbia Hydro, and Inland Natural Gas Co. Water is pumped from the Nicola River, a distance of 6 km (4 miles) and a lift of 244 m (800 ft). In March 1967, the open pit mining operations at Craigmont Mines reached their economic limit and were suspended. Before this, it had been decided that a sub¬level caving method of underground mining would be used to supply ore to the concentrator after the cessation of open pit production. This chapter describes the fac¬tors influencing the choice of mining method, some of the problems encountered, mining practices, and results. GEOLOGY The ore bodies of upper Triassic age are located in a limy horizon striking east-west, closely paralleling the intrusive Guichon batholith, bounded on the south by rhyolites and on the north by graywackes, and dipping steeply to the south (Figs. 2a, b). The ore bodies are relatively narrow with a maxi¬mum width of 79 m (260 ft), a combined strike length of 853 m (2800 ft), and a vertical extent of 610 m (2000 ft). Chalcopyrite is virtually the only copper mineral, and 20% of the ore zone consists of acid solu¬ble magnetite and hematite. The area has been subjected to considerable faulting and brecciation, which is a major factor in the mining operation. Total geological reserves, at 0.7% Cu cutoff, for the deposit were 22 316 743 t (24,600,000 st) at 1.89% Cu. An additional 5 236 270 t (5,772,000 st) at 0.6% Cu were mined from the open pit. Ground Conditions The waste rocks-graywacke, andesites, and diorite -are relatively incompetent due to the high degree of fracturing and jointing, and all require varying degrees of support. The ore zones are somewhat less fractured; ground support is still required, however, although to a lesser extent than in the country rock. Ground conditions in the main ore body are better than in the smaller, nar¬rower ore bodies. Clayey fault gouge is present in most of the faults; gouge zones may be up to 6 or 9 m (20 or 30 ft) wide. The main ground problems are associated with local weakness rather than pressure. Shape of Ore Bodies (Figs. 2a, b and 3a, b) The main No. 1 ore body is approximately 244 m (800 ft) long and 46 m (150 ft) wide. It extends ver¬tically from the original top of the open pit at 4200 ele¬vation to just below the 3060 level. The No. 2 ore body is approximately 304 m (1000 ft) long, varies from stringer width at the extremities up to 79 m (260 ft) wide, and extends from 3060 level to 2400 level. Both these ore bodies have extensions re¬sulting in additional small irregular bodies. Ore bodies are mostly steep dipping, though part of the Wing ore body, an extension of No. 2 ore body, dips at 0.87 rad (50'). This ore body varies in size, but is approximately 122 m (400 ft) long, 21 m (70 ft) wide, and about 213 m (700 ft) high. No. 1 Limb ore body is a narrow extension of the No. I Main with a vertical extent of 137 m (450 ft), average width of 18 ft (60 ft), a strike length of 152 m (500 ft), and dips steeply at 1.4 rad (80°). No. 1 East is an eastern extension of the No. 1 Main with a vertical extent of 183 m (600 ft), a strike length of 91 m (300 ft), an average width of 30 m (100 ft), and dips at 1.2 to 1.4 rad (70 to 80°). No. 1 South is at the upper west end of the open pit with a vertical extent of 76 m (250 ft), a strike length

Jan 1, 1982

By Paul Lenchuk

The concrete block industry can trace its beginnings to the early 18th century when most of the experimental work was being carried out in England. In America, the concrete masonry industry got started shortly after the Civil War and has had sometimes a spectacular, but always a steady growth since then. From a few hundred thousand concrete masonry units made in the late 19th century, the industry today produces approximately 3.3 billion concrete masonry units making it the largest industry in the United States for masonry wall materials. There were 3500 concrete masonry plants manufacturing these units after World War II. This nwnber decreased to 1500 by 1970 although the production of concrete masonry units increased by over 100% in the last 25 years. One of the reasons for this increase in production by less than half of the plants which once existed, is the tremendous strides made in automation of production machinery. The concrete masonry plant of today is probably one of the most automated small businesses in existence. Within a few years it will be possible to push a button and the entire manufacturing process will begin with no human hands touching the units until they are laid up in a wall at the manufacturing plant and are trans-ported to the job site. No other concrete product has reached this state of manufacturing sophistication and it is one of the reasons why the price of a concrete masonry unit is not much different than it was 2S years ago. Because of automation, it is safe to say that concrete masonry will remain a highly competitive building material for many years to come. The problems that beset the continued use of this material are not related to the cost of manufacturing and delivering the product. What are some of the problems as well as some of the opportunities and is the golden age of opportunity knocking rather than a wolf in disguise? The use of concrete masonry has grown each year because a larger unit was provided at less cost than other competitive materials. Concrete masonry has had severe competition from the clay products industry as well as masons who laid the product in the wall and who resisted concrete masonry for many years. Even today

Jan 1, 1971

By John H. Bassarear

Large scale equipment can reduce both capital and operating costs for concentrators. Large semiautogenous mills can be effectively utilized in big mills but they must be kept fully loaded to take advantage of their great potential. With varying hardness ores, controlling throughput is difficult and careful design must take this into consideration. A variable speed drive on large primary semi- autogenous mills can overcome this problem to a considerable degree. This paper provides a base case using standard accepted technology of two wound rotor single speed 4,476 kW (6,000 hp) motors to drive the primary SAG mills of a hypothetical 36,364 mtpd (40,000 stpd) typical porphyry copper mill. One other fixed speed drive will be described and five variable speed drive configurations will be reviewed. Capital costs for the entire grinding circuit, from crusher product to flotation feed, were developed for the base case and each of the alternatives. A technical evaluation comparing the advantages and disadvantages of each drive is presented.

Jan 1, 1985

By Weijie Wei, Jinwang Zhang, Shengli Yang

In longwall top-coal caving (LTCC) mining with an inclined seam, the recovery rate is low and equipment stability is poor due to the unbalanced top-coal drawing process. To address these problems, this paper proposes the dynamic group caving method (DGCM), whose basic premise is that when the drawn volume of top coal from a support reaches about half, the next support begins drawing top coal, and the drawing process between the two supports is half done. Using particle flow code (PFC), the caving mechanism of top coal under DGCM was investigated. The results are of significance to realize high efficiency and precise caving in LTCC mining with an inclined seam.

By Paul H. Johnson

Resource Engineering and Development, Inc. is desigining and building a portable 150 to 225 tpd, flotation-cyanide leach plant with unitized, skid-mounted components. This plant design, with its portability, low capital investment, and high recovery of silver and gold from many partially oxidized ores, is well suited to treat many small, highgrade deposits, old waste dumps, and old mill tailing piles. A description is given of flotation and/or cyanide leach tests run on 18 partially oxidized, newly mined ores; waste dump materials; placer slimes; and old mill tailings.

Jan 1, 1981

By William J. Cavanaugh

In 1967, Lone Star Industries, Incorporated, established a program to carry out the necessary Research and Development work to bring the Snyder Process to commercial application. The purpose of this paper, is to present the detailed metallurgical results gathered in comparing the Snyder Process of Comminution to conventional grinding techniques for the milling and beneficiation of certain ores and other materials. The ore primarily dealt with in this paper is a fine-grained magnetite ore, containing approximately 23% acid-soluble iron, from the Lake St. Joseph ore body of Steep Rock Iron Mines, Ltd., (Canada). This particular example was selected for presentation in this paper because extensive comparative results with conventional methods of grinding were available. Also briefly described in the paper are the comminution of other ores and materials such as porphyry copper ore and alumina.

Jan 1, 1973

By J. Noll, D. Yantek, B. Kendall, J. A. Organiscak

"A self-tramming remotely controlled mobile Dry Scrubber (DS) was developed by J. H. Fletcher and Co. under a contract with the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research (NIOSH OMSHR) to reduce exposure of miners to airborne dust. NIOSH OMSHR laboratory testing showed that the DS averaged greater than 95% dust removal efficiency with the disposable filters and averaged 88% and 90%, respectively, for the optional washable filters in their pre-washed and post-washed test conditions. Although the washable filters could be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-minute washing period. The DS’s velocity pressure regulated variable frequency drive (VFD) fan maintained a relatively consistent airflow near the targeted 1.43 and 4.25 m3/s (3000 and 9000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60 Hz fan motor frequency or horsepower rating at 2610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the DS also showed that the outlet side of the scrubber was noisier and the loaded filters increased sound levels as compared to clean filters at the same airflow quantities. With loaded filters the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level (PEL) of 90 dB(A) at or below this airflow quantity (1). The DS’s washable filters were not used during field testing because of their lower respirable dust removal efficiency and the airborne dust generated from filter washing. Field testing the DS with the disposable filters at two underground coal mine sections showed that it can clean a portion of the section return air and provide about a 50% dust reduction at the face area downstream of the continuous miner (CM) operation. INTRODUCTION Coal mine worker overexposure to coal and quartz dust continues to be a problem at underground coal mining operations in the U.S. The U.S. Mine Safety and Health Administration (MSHA) recently changed the standard for coal mine worker respirable dust exposure from 2.0 mg/m3 average during an eight-hour shift to 1.5 mg/m3 average over the actual working shift, effective as of August 1, 2016 (1). If more than 0.1 mg/m3 quartz mass is found in the coal mine worker dust sample, the applicable respirable dust standard is further reduced to the quotient of 10 divided by the percentage of the quartz in the sample (1). Over 90% of the mechanized mining units operating in U.S. underground coal mines are continuous mining machines (2). MSHA inspector dust samples from 2009 to 2012 showed that 3.7% of continuous miner operators exceeded the 2.0 mg/m3 dust standard, while 8.8% of these dust samples exceeded the new 1.5 mg/m3 dust standard and 9.7% of these samples exceeded the reduced quartz standard (3). Additionally, roof bolter dust samples at these mechanized mining units during this same period have exceeded the 2.0 mg/m3, 1.5 mg/m3, and reduced quartz levels at 1.1%, 3.7%, and 10.6%, respectively (3)."

Jan 1, 2016

By D. Donison

The practice of blasthole mining is typically applied in competent ground conditions, primarily because of the open stope dimensions. At Magma Copper -Superior Mine, a field pilot project was completed examining a variation of blasthole mining in poor ground conditions. The results were very encouraging not only from a technical viewpoint, but also productivity viewpoints. This paper describes the pilot project and the resulting implications.

Jan 1, 1994

By M. A. Berdine, C. N. Thompson, D. Brock

The raise bore method of shaft construction has been success-fully used in the mining and construction industries for over thirty years. In the mid 1990’s, Twentymile Coal Company (“TCC”), now affiliated with RAG American Coal Company, used this method for a moderately deep small diameter shaft and the raise bore and slash method for a shallow larger diameter shaft. In late 2001, TCC contracted to raise bore a 431-meter deep, 6.2-meter diameter shaft. During the raise bore and shaft lining processes, regional horizontal stress fields resulted in extensive elliptical caving beyond the original design diameter. This paper discusses the engineering approaches and procedures used to safely complete construction of the raise bore shaft.

Jan 1, 2004

By A. J. S. Spearing, B. Forbes, T. Kostecki, A. Hyett

Improving upon the past understanding of the interaction between installed rock bolts, the immediate roof and sidewalls is vital for the implementation of sound support system design, as this has a direct impact on rock-related safety. This is the primary goal in rock-bolt-related research. The earliest research in this field concentrated on limited laboratory and in situ measurements accompanied by theoretical analyses, based on the Kirsch equations. This represented the initial insight into understanding relative ground movements and their impact on primary support. However, these studies were far from complete. More recently, major technological advances in computing power within the mining industry has changed the scope from theoretical analysis to computer simulation. Even with these advancements our understanding of rock bolts in situ and in the laboratory has not progressed, particularly concerning bending and shear. To measure the behavior of rock bolts, the widely accepted practice is to populate the bolts with an array of strain gauges. Historically, resistive foil strain gauges or long displacement sensors have been used. Additionally, all instrumented rock bolts have used only two diametrically opposed slots. Rock bolts instrumented with these methods have significant shortcomings, one of which is the inability to capture shear and bending. The shearing and bending of rock bolts are particularly common in tabular soft rock mining, such as coal mining. This paper discusses the use of three slotted rock bolts, cut diametrically 120º apart, and two new optical fiber technologies populated along the entire rock-bolt length.

Jan 1, 2015

Two new inorganic-organic hybrid polymers, Al(OH)3-polyacrylamide (Al(OH)3-PAM) and Mg(OH)2-polyacrylamide (Mg(OH)2-PAM) were synthesized and successfully applied for the treatment of oil sand tailings. The results indicate that both Mg(OH)2-PAM and Al(OH)3-PAM were unaffected by the change in pH, and could be applied to oil sand tailings with varying sand-to-fine ratio (SFR). The optimum dosages for the Mg(OH)2-PAM and Al(OH)3-PAM were about 330 g/ton and 650 g/ton, respectively for SFR 3.75. The flocculated oil sand tailings dewater quickly producing 66-68% solids. The flocculated tailings produced similar filtration rate before and after shear. Mg(OH)2-PAM treated oil sand tailings produced twice the filtration rates (220 ml/min) compared with Al(OH)3-PAM. This study clearly indicates that Mg(OH)2-PAM and Al(OH)3-PAM is a viable solution while decreasing the mass-production of tailings and increasing the rate of water-recycle.

Jan 1, 2012

By Lewis J. Patterson

In the period of time allotted to this paper, an attempt will be made to cover a great deal of territory, figuratively speaking, as far as our experience with ammonium nitrate is concerned. In giving this subject the "broad-brush" treatment, it will be necessary to generalize on the major points which at the same time will permit me to avoid, to a great extent, any involvement in the purely technical and theoretical aspects of blasting. The practice of theorizing before a new idea is tried has practically been discontinued in our organization simply because experience has shown that, almost without exception, theories have fallen aside as some new development takes its place. In regard to blasting, logic and experience seem to have little place in this phase of quarry operations. As the use of low cost blasting agents was introduced in our operating practice, a man who had no previous experience in the field of blasting but with sound knowledge in safety procedures was given the responsibility of supervising the drilling and blasting operations. A total lack of experience is not ordinarily recommended as a prerequisite to assuming the responsibilities of a supervisory position. However, in this case it was obviously a wise decision because there were no pre-conceived ideas as to what techniques would or would not be successful.

Jan 1, 1958

By Susan P. Taite, Alain R. Charest, Peter D. Lewis

The El Sauzal deposit is a classic, high sulfidation, epithermal gold system located in the southwestern Chihuahua state of Mexico (Fig. 1). A Francisco Gold geologist discovered the prospect in1995. El Sauzal was encountered as a result of an extensive grassroots exploration program in the rugged, dissected volcanic terrains of the Sierra Madre Occidental, around the historical Batopilas silver camp. At El Sauzal, high grade gold is hosted within a series of more permeable, low-dipping, lithic and fine-grained dacitic rocks of early Tertiaryage. The mineralization appears tobe structurally and lithologically controlled. The alteration characteristics are typical of a high sulfidation system, including kaolinite, illite, alunite, dickite and pyrophyllite.

Jan 1, 2005

By W. G. Lawrence

The rapid development of science and technology in Russia has been the result of well laid plans since 1918. At that time the Institute of Silicates was established is Moscow and later the establishment of similar more specialized institutes for the study of cement, glass, refractories, construction ceramics, electrical ceramics, building materials and asbestos provided the necessary research facilities for studies related to all types of ceramic inorganic materials. The' Institute of Ceramics and the Institute of Silicate Chemistry, Academy of Sciences, USSR, were founded in Leningrad. The work now going on in these various research' institutes covers every branch of silicate science and ceramics The impetus behind such establishment of special¬ized laboratories is no doubt due to the 5-year plans and the necessity of improving the scientific knowledge regarding the materials being used and the products being manufactured.

Jan 1, 1960

By Martin B. Hudson, John Yao, Matthew R. Crow, Yiming Sun, John T. Waggoner, Roozbeh Geraili Mikola

"The Wilshire Grand redevelopment project in downtown Los Angeles includes construction of a new 73-story tower. Construction required excavation up to 93 feet deep (28 m). The south side of the excavation, up to 57 feet deep (17 m), required placement of shoring within about 6 to 10 feet (1.8 to 3.0 m) horizontally away from a 400-foot-long (122 m) section of one of the existing Los Angeles Metro Red Line twin subway tunnels. These tunnels were constructed using a 22-foot-diameter (6.7 m) digger shield, and were initially supported with expanded, precast concrete segments, with final cast-in-place reinforced concrete lining. The temporary shoring system for the deep excavation consisted of soldier piles generally spaced at 8 feet (2.4 m) on center with multiple levels of tieback anchors extending above the subway tunnels. The lowest level of bracing consisted of rakers supporting walers attached to the soldier beams because installation of tieback anchors at that level would conflict with the tunnels. Numerical analyses were performed to predict tunnel movement caused by the excavation and its effects on the train operations. This paper describes the numerical modeling, tunnel and geotechnical instrumentation and monitoring program, and comparison of the computed and observed tunnel responses to the deep excavation and tower construction. With increasing urban redevelopment in major cities, the project is a valuable case history for excavation adjacent to existing tunnels. INTRODUCTION The Wilshire Grand redevelopment project includes the demolition of a 16-story hotel built in the early 1950s and the construction of a new 73-story tower in downtown Los Angeles (LA) that will be the tallest building in the western United States. The project site is situated on approximately 2.7 acres (1.1 Ha) of land bounded by Figueroa Street to the east, Wilshire Boulevard to the north, Francisco Street to the west, and 7th Street to the south (see Figure 1a). The new tower is being constructed by Turner Construction for Hanjin International Corporation. Construction of the basement and foundation of the new tower required excavation up to 93 feet (28 m) deep. Shoring was designed by Cefali & Associates and installed by Malcolm Drilling Company. Along 7th Street, an excavation up to 57 feet (17 m) deep required shoring to be installed within about 6 to 10 feet (1.8 to 3.0 m) horizontally from an existing 400-foot long (122 m) section of one of the LA Metro Red Line subway tunnels (see Figure 1b). The tunnels, extending from the 7th/Metro Station to the Westlake-MacArthur Station, were constructed in the late 1980s and early 1990s with an excavated diameter of approximately 22 feet (6.7 m). They were initially supported with expanded, precast concrete segments with a final cast-in-place reinforced concrete lining. The existing hotel was demolished in 2012 and 2013, with shoring installation and excavation for the new basement occurring as the demolition occurred. At the time of writing, January 2016, the structure of the building adjacent to the tunnels is largely complete."

Jan 1, 2016

By B. Petri, N. Rouse

"Air overpressure monitoring procedures and instrumentation guidelines which apply to production blasting in underground limestone mining are not readily available. The industry also lacks an applicable source for air overpressure levels that are produced by blasting operations in underground limestone mines. As such, there was no available background data from which the expected overpressure levels from production blasting in a new underground limestone mine could be predicted. During the development phase of the mine, it was imperative that newly constructed underground structures be capable of withstanding the overpressure produced by blasting in nearby production headings. To ensure the structures could withstand the blast-induced overpressure, a study was conducted to record empirical overpressure data and develop a model which could be used to control air overpressure levels by the production crews. This document describes the procedures used to develop the model, the development of the model, and the applicability of the model for predicting underground blast overpressures. INTRODUCTION A developing underground limestone mining operation required that a ventilation wall be built to house the permanent mine fans. At the time of the study, the mine was a single-level room and pillar operation with a 7.9 meter (26 ft) high roof, 13.7 meter (45 ft) wide entries, and 13.7 meter by 13.7 meter (45 ft by 45 ft) pillar dimensions. The mine is accessed via a 396 meter (1300 ft) long decline and 100 meter (330 ft) deep ventilation shaft. The ventilation wall was to be partially constructed of autoclaved aerated concrete blocks, for which dynamic strength data from explosives loading were unavailable. The company ownership feared that airblast may affect the wall due to the close proximity of the working faces. Therefore, the company management asked that the overpressure levels be estimated and compared with the designed wall strength. Few studies that apply to explosively-driven air overpressure levels in underground production blasting were found through a literature review. Therefore, the logical approach to assess the overpressure levels was to monitor the blast pressures at the site and conduct a thorough evaluation of the data. As a result of this study, the equipment setup and monitoring procedure used to record the airblast data is described. Finally, the experimental data gathered during the monitoring program is presented, trends and findings from the data are discussed, and recommendations for further study are presented."

Jan 1, 2015

By Anthony Harding

In a world of technology and electronic communication, it is easy to forget what engineers do best with a problem: sitting around a table, exchanging views and ideas with sketches and respecting everyone?s view. This was the approach adopted in the project to arrive at a solution for the cross passage opening sup-port for the Seattle University Link Extension. Schedule and space constraints usually impede concurrent cross passage excavation and tunnel boring machine (TBM) operation. And where the space is constrained, opening support solutions that maximize available cross sections are of great benefit. While there are a number of solutions that minimize space, some of these solutions can require expensive steelwork and extensive drilling and fixing. However, following a detailed round-the-table discussion of the options and constraints, it was identified that a shotcrete shell would not only limit obstruction of the space during installation, but also permit easy installation, particularly around services, and avoid costly steelwork and drilling and fixing.

"Hecla Limited has been investigating the potential benefits of using a Spendrup/Compact Filter Technic (CFT) diesel filtration system to remove diesel particulate matter (DPM) from the mine atmosphere to optimize use of the available air. The National Institute for Occupational Safety and Health (NIOSH) has evaluated the scrubber efficiency for dust and DPM which is to be presented in another report. This paper reports on a new mining application of a carbon particulate sensor’s ability to continuously monitor long-term mine DPM levels in conjunction with the scrubber evaluation. Magee Scientific is the manufacturer of the Aethalometer®, a continuous black carbon monitor which has been used extensively in worldwide ambient air quality monitoring networks. Two Aethalometers were used at the mine to assess their potential to continuously track underground DPM levels. In this first underground mine application, the Aethalometers were used to continually monitor black carbon (BC) in the intake and exhaust of the CFT scrubber system. Results showed that an off-the-shelf Model AE33 Aethalometer could continually track underground BC levels for extended periods of time over the course of the six-week trial. Data at the scrubber intake over 14 days of testing showed that DPM filtration would be required less than half of the time to maintain BC levels below 50 µg/m3. If the Aethalometer BC data output were “smart coupled” to control a 200-HP in-mine scrubber, significant electrical cost savings would be realized. INTRODUCTION Mine ventilation airflow quantities are calculated to maintain a safe and healthy environment for miners. Dilution of diesel particulate matter (DPM) is often a key factor used to determine the required quantities of ventilation air (Bugarski et al. 2011). DPM emissions and exposure levels are highly variable depending on mine schedules and activities (Janisko & Noll 2010); however, lacking technology to continuously monitor levels, mine ventilation systems are often over-designed in order to handle worst-case scenarios to ensure that DPM levels are maintained at or below regulatory limits. As mines go deeper it becomes more difficult to supply air, and the development of new shafts for air is not economically feasible (Basu et al. 2008). Cleaning and reuse of available air then becomes an attractive option to maintain good air quality."

Jan 1, 2016

By Steve Kral

"Repairing and replacing the nation’s aging and crumbling infrastructure has become a major issue with the American public. It is no secret that the upkeep of roads, tunnels, bridges, and water and waste water facilities has been neglected for decades. Cities, states and towns across the United States are now grappling with these issues, ones that will take decades and billions of dollars to fix.Because of this infrastructure issue, the North American tunneling industry is flourishing. Cities across the country are looking to go underground to alleviate traffic issues, transporting water and waste water to more people in more efficient ways.In October, the seventh annual Cutting Edge conference was held in Atlanta, GA. Put on by the Underground Construction Association of SME and Britain’s Tunnelling Journal, about 175 tunneling and underground construction professionals from around the world attended. Attendees included owners, designers and contractors. An accompanying exhibit included 28 companies.The theme of the two-day conference was Advances in Tunneling Technology. Speakers examined the latest advances in tunneling technology, its methodology and how these advances can be harnessed to assist upcoming major tunneling projects. The conference featured a tailored, high-end, single-track program of subject-specific presentations that focused on innovation and practical experience. Two in-depth panel discussions at the end of each day were also included.Patricia Mulroy was a keynote speaker on Monday. She is senior fellow for climate adaptation and environmental policy at The Brookings Institution. Like many others, Mulroy believes the U.S. infrastructure in in a state of disrepair. But, she said, no one wants to talk about it. “We need to have a conversation about infrastructure. We cannot be afraid to talk about building it and the cost.” For this to happen, though, the nation needs leadership."

Dec 1, 2018