Search Documents

Multilevel-multiseam hardcoal mines on the European continent usually consist of a huge network of underground openings, sometimes more than 200 km long in total, with some longwalls operating down to a depth of 1,500 m. While operating several longwalls simultaneously, these mines are making use of a number of stationary and mobile measurement- and analysis units in their main ventilation passes combined with atmospheric measurements on the surface. This paper provides an overview over the systems and technology used and describes the typical set-up of a measuring net. To detect and monitor underground fires through fire gases measurement and -analysis, a mobile underground testing laboratory collects data locally in the area of the fire. These laboratories have proven to be extremely useful not only during the actual fire fighting but also for the long-term gas measurements in critical mine areas. They have repeatedly detected starting fires and have thus given the mine the opportunity to react early and to avoid larger damage. Therefore several mobile laboratory units have now been installed for long-term testing in a number of German mines and similar units are being used in the Czech Republic and Poland.

Jan 1, 2012

By R. L. Hills

America's industry uses about 44% of the total energy consumed by the nation directly as fuel burned in industrial plants or indirectly as fuel burned by utilities to provide electric power. In addition, industry requires raw materials or feed stocks derived from fuel sources or having fuel value. This represents about 11% of total U. S. energy consumption, bringing industry's portion to about 55%. Adding that portion of energy consumption required by the transportation sector to move raw materials, intermediates, and finished products, the total energy impact of industry approaches 213 of total U. S. consumption. It is obvious that American industry has the largest share in the task of balancing energy demand and supply. What are we going to do? -- We must increase the supply of energy and increase the beneficial results obtained from each unit expended. Both avenues, unfortunately, are limited in extent and speed. Increases in supply cannot occur without drastic and permanent increases in cost. These increases in cost are un- desirable and inflationary but do provide incentive for the rational businessman to expend the effort and money required to improve the effectiveness of energy in industry.

Jan 1, 1975

By James W. Clark

This paper is a description of certain geologic aspects of the Inspiration mining operation. It is not a geologic description of the Inspiration deposit nor an exposition of all the geologic work involved in the development and exploitation of the deposit. A few specific examples of the application of geology and geostatistics to the mining process are given to illustrate the progress that has been made in making the Inspiration Mine more efficient and cost effective, and a statement of the philosophy of geologic applications is offered.

Jan 1, 1984

By D. Brosnahan, J. Gathje

Newmont Metallurgical Services (NMS) recently acquired a Scanning Electron Microscope (SEM) with a JKMRC/FEI Mineral Liberation Analyzer (MLA). With the MLA software package, raw particle image and X-ray data can be converted into particle mineral maps and bulk and liberation data can then be calculated for minerals of interest. This type of quantitative mineralogical data can then be used for a wide variety of applications. Ore characterization with MLA can be carried out for existing or processing plants in development. MLA characterization of laboratory test products provides valuable liberation information that assists the research metallurgist in better planning and developing process treatment options for various ore types. This paper describes the use of MLA characterization in a copper flotation test program where the use of various testing options for arsenic depression was being evaluated.

Jan 1, 2007

By Jaidev Sankar

The dream of constructing the new Second Avenue Subway in New York has finally become reality as the first construction contract package is currently underway. This first contract requires the construction a TBM Launch Box in the middle of Second Avenue from which a Tunnel Boring Machine (TBM) will bore two tunnels south to 63rd Street. This paper will discuss the design of this contract and how construction has progressed including preparation, site constraints, utility construction and com-munity impacts while highlighting the challenges of working in an urban environment. It will also discuss moving forward on this major project outlining the remaining contract packages including their scope and status.

By Steve Kral

A near-record crowd of mining history enthusiasts made the trip to Leadville, CO in September to attend the National Mining Hall of Fame and Museum’s 19th induction banquet. Dressed in Victorian garb, black tie tuxedos and formal gowns, the 268 people honored four distinguished men who made a lasting impact on the U.S. mining industry. They joined 188 other inductees. The first induction banquet took place in 1988, with about 500 people attending.

Jan 1, 2007

By M. Gangal

CANMET-MMSL, in cooperation with Dry Systems Technologies and Quinsam Mine, conducted a study to determine the effects of B50 biodiesel on the emissions of a flameproof diesel power package in comparison with mining diesel fuel for application in underground coal mines. The emissions testing for coal mine application requires that the intake air mixture to the engine should be at 1.25 percent methane by volume in air. The tested power package system included a naturally aspirated, mechanically-controlled diesel engine with a diesel oxidation catalyst (DOC), a heat exchanger, flame arresters, and a low temperature disposable diesel particulate filter. The engine dynamometer tests were conducted at the CANMET-MMSL Diesel Emissions Research Laboratory in Ottawa using the ISO 8178-C1 test protocol. The separate and combined effects of a B50 biodiesel blended fuel, and with and without 1.25% methane enriched intake air were measured on a diesel power package. Fuelling the baseline engine (without methane), with B50 biodiesel blend reduced carbon monoxide (CO) by 44%, and increased nitrogen dioxide (NO2) by 19%, and particulate matter by 31% relative to the mining diesel fuel. Similarly, injection of 1.25% methane to the intake air for baseline engine with mining diesel fuel increased engine power by 15%, CO by 124%, and NO by 15%, and decreased NO2 by 13%. The effect of B50 biodiesel relative to the mining diesel for coal mines application (with methane for both fuels) was to reduce CO by 27%, and NO by 6%, and increase NO2 by 23%, with no change in engine power. The overall results indicate that the minimum ventilation rate for the equipment application in coal mines with B50 biodiesel was 4.11 m3/s (8,700 cfm), slightly higher than the ventilation rate of 4.01 m3/s (8,500 cfm) with the mining diesel fuel. This slight increase in ventilation rate for B50 biodiesel fuel was due to an increase in NO2 at one of the operating test points, and the ventilation rate for this equipment was governed by NO2 in the exhaust gas.

Jan 1, 2009

By Matthew Wilcock, Kenichi Soga, Peter Wright

"This paper discusses how an existing grey cast iron segmental tunnel lining responds to construction of a new SCL tunnel transversely beneath with zero clearance; how the damage assessment for the existing tunnel was conducted for impact of longitudinal movement; how the tunnel is subsequently instrumented to observe both movement and stress manifestation at its longitudinal connections and how the results from the instruments compare with the prediction. An assessment of neutral axis of the tunnel in longitudinal flexure is also explored using interpolated horizontal displacement data from a conventional monitoring system. INTRODUCTION The Royal Mail Tunnel (RMT) (formely Post Office Tunnel or ‘Mailrail’) was constructed using semi-mechanised deep level construction techniques from 1914 and 1917 (Lee 1938). Commencing full commercial operation in 1926, the system was until 2003; conveying parcels the 6.5 miles between seven sorting offices in the center of London, and linking the system with main line rail stations, Paddington and Liverpool Street (The British Postal Museum & Archive 2013). A single tunnel of 2.74m internal diameter facilitated a bi-directional twin narrow-gauge (~611mm gauge) railway road system for electric driverless operation. The tunnel lining is segmental grey cast iron (grade 10) made up of six flanged segments and a smaller flanged key segment; constructed into a ring of width 508mm The external diameter of the tunnel is 2.971m. For further details of the tunnel lining and material properties are outlined by (Devriendt & Alhaddad 2014).London Underground Bond Street Station is a major station of the London Underground system in the very center of London; in its vicinity, the RMT runs west-east perpendicularly above the north south Jubilee Line tunnels. Historic survey record of the Jubilee Line’s (the then Fleet Line) construction in 1974 and its impact on the RMT case is documented in (Crossrail 1993): it is one of only a hand full of case-studies frequently cited when assessing the impact of new construction scenarios of this type; not least including the assessment of the same tunnel, at the same site some 40 years later, and the subject material for this paper: It noted significant vertical displacement of ~90mm to the RMT without noticeable serviceability or operational impediment."

Jan 1, 2016

The National Mining Hall of Fame and Museum (NMHFM) in Leadville, CO will induct the class of 2011 on Sept. 10, 2011. Representing the coal, metallurgical/processing, research and development, marble and lead industries, this year?s inductees cover a diverse crosssection of the mining industry. William Francis Diamond, Wayne Hazen, Redfield Proctor and Jeffrey Zelms will join 210 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame at the 24th Annual Induction Banquet and Ceremony. The members of this year?s class were selected for being visionaries, leaders and ambassadors both within their own sectors and across the industry at large. Diamond had an illustrious engineering and managerial career that spanned four decades with Island Creek Coal Co. During that time, he was responsible for the engineering and construction of the deepest coal mines producing in North America at the time.

Jan 1, 2011

By R. L. Wiegel

Several mineral process modeling and simulation packages are currently available for use in evaluating the performance of alternative process flowschemes. A critical link that has been missing from these packages is the ability to quantitatively model the effect of size reduction on the liberation of the valuable and waste minerals in the ore being processed. Although there have been several approaches taken to this problem over the past 25 years, none has led to a satisfactory conclusion. A technique has been developed for measuring the effective liberation characteristics of magnetic taconite ores, and a program has been constructed which makes use of these liberation characteristics in simultaneously simulating both size reduction and mineral liberation as it occurs in tumbling mills. This is an especially important step in the modeling of magnetic taconite processes, where magnetic rejection of low grade wastes between grinding stages mandates that a predictive capability be available. The current application is specific to magnetic taconite, but it is possible that a similar approach could be used for other types of mineral systems.

Jan 1, 2002

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008 ? ?I guess that without the occasional complaint, your mine is probably over-ventilated? (Marks, 2008). Miners are seldom in this situation and often spend much of the time trying to find enough air to keep the operation running. With examination there are some things that can be done to make the best use of ventilation systems. Should there be surplus air, in which some of these options may result - financial and other benefits can be obtained. Some of the issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and non-metal mines. Also, operations are faced with demands from reserves that are deeper, hotter and further away from fans and shafts, not to mention increased production demands. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Most of the options presented in this paper are useful for metal non-metal operations but some may be applicable to coal too. OPTIONS FOR IMPROVEMENT Some of the areas to be addressed are shop ventilation methods, auxiliary equipment areas, dedicated intakes and returns, optimizing development, examination of mine airway utilization and alternative ventilation methods. UNDERGROUND SHOPS First, examine what is being done with the underground shop air. If it is being coursed directly to the returns there may be some potential to better utilize this, in most cases, relatively contaminant free air. Research the legal options for ventilating mine shops. MSHA regulations in 30CFR 57.4761 (1) allow the following options: To confine or prevent the spread of toxic gases from a fire originating in an underground shop where maintenance work is routinely done on mobile equipment, one of the following measures shall be taken: use of control doors or bulkheads, routing of the mine shop air directly to an exhaust system, reversal of mechanical ventilation, or use of an automatic fire suppression system in conjunction with an alternate escape route. The alternative used shall at all times provide at least the same degree of safety as control doors or bulkheads. Discussion This regulation gives some operators flexibility in ventilating underground shop facilities. If shop air is to be coursed through the work area, and then directly to the mine return, the question should be asked ? is the quality of air good enough to be reused in the mine, and if so, what are the risks? Can the risks be accommodated and managed to accomplish the change? If so, a considerable increase in mine level airflow could be attained by reusing shop air. Clearly, regulations are a minimum standard, and can be exceeded. Metal non-metal mine regulations are not as specific as coal due to the multitude of different mining methods and conditions utilized. Risks must be thoroughly examined and addressed to assure a safe environment. Issues Determine what contaminants are being produced in the work area ? welding fumes, diesel exhaust, paint fumes, chemicals and solvents, etc. Survey the area and determine exposures. MSHA requires exposure monitoring in 30 CFR 57.5002 (1) of dust, gasses mists and fumes to assure air quality is being met. Perform surveys and examine existing data to quantify personal and area concentrations of contaminants. Often there is adequate circulation such that exposure levels in shop work areas are low. After sending shop air back into the system any contaminants would be further lowered by dilution with other mine intake air downstream. Look at the shop work schedule. If only on day shift, the other two shifts and possibly weekends have no activity or source of contamination to affect the ventilation system. The worst case planning scenario would be a shop fire. Study and simulate how this would affect the mine and shop area. MSHA regulations require an escape route and a fire suppression system be installed and maintained as follows in 30 CFR 57.4671 (1): (d) Automatic fire suppression system and escape route. If used as an alternative, the automatic fire suppression system and alternate escape route shall meet the following requirements: (1) The suppression system shall be? (d)(1)(i) Located in the shop area; (d)(1)(ii) The appropriate size and type for the particular fire hazards involved; and (d)(1)(iii) Inspected at weekly intervals and properly maintained. (2) The escape route shall bypass the shop area so that the route will not be affected by a fire in the shop area. Case Study In an underground room and pillar mine, active mine workings were advancing further away from the mine shaft with deteriorated returns and leakage having a negative effect on ventilation airflows to the face. Mine level airflows were 236 m3/s (500,000 cfm) and shop airflows were 24 m3/s (50,000 cfm) (see Figure 1A). No additional capacity was available at the main surface fan. A solution was to utilize the shop air then send it to the mine areas instead of directly to the return. Considerable information on shop air quality and exposures from many years of operation was examined and no negative data was discovered. A risk analysis determined that moving forward with a shop air reuse program was desirable. A plan was developed, analyzed and decision to proceed approved by mine management. The change was simulated on the computer with the USBM/MTU MFire program before being implemented. This included utilizing fire scenarios to examine potential exposures to inby mining sections and plan escape routes. A monitoring system was designed and installed in cooperation with the US Bureau of Mines to monitor carbon monoxide

Jan 1, 2009

By Kevin Vander Tuig, Tim O’Rourke, Rick Vincent, Doug Lopata, Kellie Rotunno, Dan Dobbels

"The Northeast Ohio Regional Sewer District (NEORSD) was required under the Federal Clean Water Act and U.S. Environmental Protection Agency’s (U.S. EPA) Combined Sewer Overflow (CSO) Control Policy to develop a Long Term Control Plan (LTCP) to reduce or eliminate overflows from its permitted CSO outfalls. The LTCP was completed in 2002. Key components of the plan include: 26 miles (42 km) of deep storage and conveyance tunnels providing a total CSO storage volume of 325 million gallons (MG) (1.2 billion liters); over 30 miles (48 km) of consolidation sewers to route CSO control flows to the tunnels; and associated diversion/inflow control structures and drop shafts. Final design and construction of the initial phases of the LTCP are completed or underway. Advanced planning of the final phases began in April 2013. This paper summarizes this advanced planning process and, specifically, how hydraulic performance and tunnel design and construction considerations were balanced to eliminate unnecessary projects and shafts, reduce implementation risks, and reduce program costs by approximately $650 million. BACKGROUND The Northeast Ohio Regional Sewer District (District) serves an area of approximately 350 square miles (SM) (907 km2), including combined (81 SM; [210 km2]) and separate (269 SM [697 km2]) sewer systems that discharge to three wastewater treatment plants in the greater Cleveland area. The service area, shown in Figure 1, is divided into three districts—Easterly, Westerly, and Southerly—each having its own interceptor system and treatment plant, ranging in wet weather treatment capacities from 100 to 735 million gallons per day (MGD) (378.5 million to 2.8 billion L/day). The system includes 124 permitted combined sewer overflow (CSO) outfalls overflowing into the region’s tributary streams, Cuyahoga River, and Lake Erie."

Jan 1, 2016

By Michael S. Kucker, Stuart Warren, Robert A. Robinson, Michael J. Lehnen, David McAllister

Geotechnical conditions exposed by the phased exploration programs have had a major impact on the selection of excavation and support methods, dewatering requirements, size of openings, vertical alignment, and estimated cost of construction for the Beacon Hill Tunnel and Station section of the “Link” Light Rail. Beacon Hill is comprised of a very complex glacial geology, including numerous slickensided fractures, injected sand dikes, and multiple perched groundwater levels as revealed by a phased boring program and exposed in a test shaft. The Geotechnical Baseline Report (GBR) presents this complex geology along with a “tool box” of alternative additional support systems to accommodate the varying ground conditions during construction of the station excavation. Additional explorations will also be accomplished during construction to further refine the geotechnical interpretations and provide an opportunity to use pro-active ground improvement techniques to optimize the station excavation and support requirements.

Jan 1, 2005

Syncrude Canada produces a large part of Canada’s crude oil supply. The company processes about 225,000 bbl/day. The oil produced is used for jet and automobile fuel, home heating oil, plastics and other consumer synthetics. Crude oil is produced through a process of mining, extracting and upgrading bitumen. A rich supply of bitumen is contained in the Athabasca oil sands deposit in northern Alberta. Tailings from the bitumen processing are sent to a settling basin.

Jan 1, 2000

By V. Z. Sun

One of the major concerns of ground control in a coal mine is safety against failure of one of three components (i.e. roof, pillar, or floor) of the mine entry. In order to better design and evaluate stability of the mine entry with a certain confidence, a reliability approach is introduced rather than using the conventional safety factor (SF) method only. Advantages of using the reliability approach is that it not only takes variability of both rock/coal properties and stress distribution into consideration, but also assesses the stability of each component and mine entry as a whole system. Therefore, it is anticipated that, by using this approach, the current ground control technology in coal mine will convey a better sense of confidence. The results of a case example show a significant influence on the current design concept and stability evaluation of mine entry.

Jan 1, 1997

By L. Xinguang

Shandong MinMetals Corporation, a state-owned import and export organization located in the city of Qingdao, Shandong Province, China, was opened in 1954, with the mission of marketing metal products and industrial raw material in oversea areas for hard currency to support the modernization project of the country as well as the province. The management officers are appointed by the provincial government, and report to the Foreign Trade Department of Shandong Province. Meanwhile, the company also receives guidance from MinMetals head office in Beijing, the capital city of China. The head office does not own and control any provincial MinMetals organizations, but merely coordinate business among provinces.

Jan 1, 1990

By Y. Paul Chugh

NIOSH and the Illinois Clean Coal Institute are funding studies on characterization of coal and quartz dust in Interior Basin mines since 2009. Coal dust characteristics vary significantly and, are vital for the development of the engineering controls. This paper presents wettability characteristics of coal dust with respect to its chemical and physical properties, since wettability is considered to be a primary dust control technique. Particle size distribution, inter-particle interactions during wetting and quartz associations with organic and inorganic matter in coal seams is critical for understanding wetting phenomena. Silica content in the un-wetted fractions was found to be very high during wetting tests. Wetting of quartz may be limited by its association to hydrophobic materials as well as buoyancy forces resulting from particle size characteristics and particle-particle interaction in the wetting agent. Temperature of the wetting solution and effective contact time between dust particles and water droplets are found to be two important variables affecting the wettability. The characterization data obtained from this study can be utilized to develop engineering controls.

Jan 1, 2011

By Jiachen Wang, Nan Wang, Yang Li

The close-multiple coal seam is an important component of China’s coal resources and plays a key role in total coal reserves. However, the overburden movement in the mining process of close-multiple coal seams is usually extensive, which is seriously affected by overmining. It is therefore essential to study the mechanism of roof breakage, the relationship between the shield and the surrounding rock, and the mechanism of overburden movement to ensure the safe operation and the efficient exploitation of close-multiple coal seams. This work first proposes a technical route for intelligent ground control. Second, the principle of cooperative control between the shield and overburden roof is revealed, and the shield support capacity calculation method is summarized. Third, the quantitative criterion for disturbance degree of key stratum (KSDD) is proposed based on the key strata theory. Finally, several intelligent evaluation and analysis systems have been developed in terms of overburden breakage and shield support capacity, multi-information analysis of ground control, and disturbance degree of overburden. The research results may provide an essential reference for the development of intelligent ground control in the mining process of close-multiple coal seams

Jul 1, 2023

By QINGXIANG CAI, Lin Li, PENG LIU, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, YONGLI ZHOU

The concept of green mining is to improve the mining industry in a holistic way so that it is safe, efficient, and environmentally sustainable. The purpose of this study was to develop an evaluation index system of green surface mining based on the theory of green grades. The evaluation model is comprised of three attributes (safety, efficiency, and environment), nine criteria, and 35 indicators. The fuzzy comprehensive evaluation method was used to determine the weights of indicators by taking into consideration degree centrality, closeness centrality, and betweenness centrality. Findings indicate that the environment is the most critical aspect of green surface mining, followed by efficiency and safety. The top five ranked green mining success indicators were the application of new technology, starting-off-rate of equipment, science and technology input to total investment, the number of accidents (decreased), and the production (increased). It was observed that more improvements are needed to overcome water, air, waste, and sound pollution. Attention should also be paid to land reclamation and post-mining land uses, which are key factors in green mining. The proposed model can be applied to evaluate and improve the level of green surface mining in other regions. This study provides a tool for decision-makers that can offer technical assistance to green mining.

May 26, 2020

By Robin Dill, Julian Prada, Kathryn Kelly, Brian Hann, Todd Moline

Narragansett Bay Commission’s (NBC) Pawtucket Tunnel Project includes construction of the 11,600-ft long, 30-ft ID, deep rock tunnel. This paper presents insight into the features and benefits of lump-sum, design-build that led NBC to select it as the project delivery method. The use of a design-build contracting process that included proprietary meetings to discuss and obtain feedback on Alternative Technical Concepts as well as to facilitate reaching consensus on modifications to the GBR-B is also described. The discussion includes features and benefits of design-build process that not only addressed NBC’s desired outcomes, but also allowed the Design-Builder to propose several innovative changes to the Base Technical Concepts included in the bid documents, and to develop a GBR-C that was compatible with their proposed means and methods of construction and addressed what they believed to be the more significant subsurface risks on the project.

Jun 13, 2023