Search Documents

Recent studies on the physico-chemical properties of molten slags and oxide solid solutions of interest are reviewed. The review covers redox and phase equilibria in slags, viscosity, diffusivity, electrical conductivity, kinetics of interfacial reactions between slags and CO-CO2, interfacial properties and phenomena. Some highlights from ongoing work on modelling phase diagrams, component activity, viscosity and electrical conductivity of multi component slags will be presented and results compared with published experimental data on slags with or without suspended solid phases.

Jan 1, 2004

By C. Maree

Paper written on project work carried out in partial fulfilment of B. Eng (Chem. Eng.) This paper describes the development and use of a process simulator to optimize gypsum recovery at Afmine, a small plant near Yzerfontein on the South African West Coast. The simulator consisted of models of the major plant equipment, viz. hydrocyclones, surge bins, settling tanks, a primary sieve and a dewatering screen. Experimental data suggested that the equipment could be modelled satisfactorily from data published in the open literature. Simulation studies have indicated that gypsum losses on the plant could be reduced substantially by means of some relatively minor modifications to the plant layout. Moreover, sensitivity analyses of the plant have indicated that optimization of the settling tanks should receive priority over the other process units.

Jan 1, 2005

A Seismic Hazard Scale (SHS) has been developed to provide a practical seismic hazard assessment tool applicable to mine site personnel. It has been applied to seismic data sets from numerous Western Australian mines. The SHS is applicable when quantifying seismic hazard on a mine wide scale, on a mining block scale, and on a local cluster-by-cluster scale. Spatial mapping of variations in seismic hazard is a particularly powerful application of the scale. The SHS is sensitive to temporal increases in seismic hazard. It has also been shown that the SHS can be applied to estimate seismic hazard when seismic monitoring data are not available. The SHS is a simple derivation of the Gutenberg-Richter relation. There are assumptions and limitations to the SHS that need to be considered when applying it to mine seismicity data.

Jan 1, 2004

By D. P. Venter

When Oryx Mine down-scaled in 1994, focus was placed on development, with the primary aim being the exposure and proving of ore reserves. In order to achieve this aim, development ends had to be advanced to reef at the maximum possible rate. This in turn called for support methods which could keep up with the advancing faces, taking up minimum space and time for installation, while providing on the face a real coverage and effective long-term support. In the majority of the development ends which were located in fairly competent ground, the grouted rod development support proved to be adequate until such time as secondary support in the form of meshing and lacing could be installed. The ends developing towards the eastern boundary of the mine, especially in the ?C? block, encountered extremely adverse ground conditions due to the presence of smectite zones within the footwall quartzites. Smectites are a group of montmorillonite clay materials, mainly composed of hydrous aluminosilicates. They occur as minute platy crystals in the rock mass and are especially notable for their ability to absorb liquids. Generally, the zones are found in between the bedding planes of the host rock, and may vary considerably in thickness over short distances. Wherever the smectites were exposed by the development blasting, the rockwalls weathered as the smectites absorbed water and the condition of the tunnel rockwalls deteriorated rapidly. When the smectites were left exposed and allowed to weather, it became almost impossible to install secondary permanent support such as meshing and lacing at a later stage. To minimise the exposure time and subsequent deterioration of the smectite zones, it was recommended that all development ends encountering smectites be shotcreted as soon as possible after blasting. In developing a shotcreting support methodology, both a drycreting and wetcreting system were investigated. The situation at the time ruled out the use of a wetcreting system on the basis of the extensive and costly infrastructure required, as well as its limited manoeuverability. Instead, it was decided to opt for as maller scale but more manoeuverable drycreting system. The system utilized a number of portable drycrete machines with pre-bagged cement, which could support several development ends in close proximity. Initial trials using normal 30 MPa shotcrete on 19level proved successful and the system was implemented.

Jan 1, 1998

By S. Langea, H. Lieberwirth

Impact crushers are common machines in comminution plants. Their high size-reduction ratio and relatively simple design, make them a preferred tool even when subjected to harsh wear, and producing a large quantity of fines in some applications. Until now the alignment of the operational parameters was an operator’s responsibility. Due to the random process characteristic this is mostly done based on empirical values and sensor data, such as power consumption. This paper describes a new approach for online process monitoring of the horizontal-shaft-impact crusher. The application of robust, low-cost acceleration sensors enables the permanent observation of the process characteristics. The operational and evaluation methods are determined on the basis of experiments. Subsequently the recorded measurements are analysed in regards of throughput, rotational speed and product particle size distribution. Occurring signal characteristics are described based on physical and technical principles. The measured data of the acceleration sensors at varying operation conditions provide insight in the course of process. The accurate utilisation yields the determination of the preferential process conditions providing the best balance between the pros and cons of an impact crusher. Both the experimental method and the data processing is discussed from a scientific perspective, displaying a completely new approach for the operation of impact crushers. Keywords: Impact crusher, acceleration sensors, data processing, particle size

Jan 1, 2020

By L. A. Cisternas, R. I. Jeldres, D. Calisaya

"Flotation of copper-molybdenum sulphide ores in seawater entails critical challenges such as selective recovery of molybdenite, effective pyrite depression, and reducing the lime addition required to reach highly alkaline conditions. It is essential that laboratory flotation tests aimed at solving these problems give reliable, reproducible results and indicate the correct approach for industrial operations. Rougher flotation of coppermolybdenum sulphide ores in seawater was investigated using two different cells: a modified Denver cell and a standard commercial cell. The effect of an organic reagent on the flotation performance was tested, and the fast/slow-floating model was used to describe the results. The modified Denver cell significantly improved the reproducibility of the flotation test results, due to technological enhancements such as the impeller being driven from below without a stator, which enables the whole froth surface to be scraped with a paddle at a constant depth and rate. Organic reagents are a promising alternative to inorganic reagents for depressing pyrite in seawater. However, further studies should be conducted to investigate their impact on molybdenite recovery, as well as to evaluate the possibility of depressing pyrite after molybdenite separation. The fast/slow-floating model was found to be appropriate for describing the flotation kinetics of the copper-molybdenum ores. The parameters are useful for comparing the performance at different conditions. IntroductionOwing to the increasing scarcity of fresh water, the use of seawater mining and mineral processing is becoming increasingly important (Cisternas and Moreno, 2014). Seawater can be desalinated by reverse osmosis, but this involves considerable costs, limiting it to the big mining companies (Akgul et al., 2008; Leidner et al., 2012; Ghaffour, Missimer, and Amy, 2013). Furthermore, desalination has environmental consequences (Lee, Arnot, and Mattia, 2011); for example, a desalination plant designed to process 2.5 m3/s requires an electrical energy supply of around 30 MJ/s. To supply this power demand, a thermoelectric plant burning bituminous/sub-bituminous coal mixtures at a thermal power generation efficiency of 35% might release around 1200– 1500 t of CO2 per day. Furthermore, the effluents from desalination plants are typically discharged into the sea, and their high temperature and ionic content inevitably modifies the marine environment, with unknown consequences. The direct use of seawater is, therefore, more attractive, but it also poses major challenges since seawater contains ions that adversely affect mineral recoveries. In particular, in the flotation of sulphide ores in seawater, the floatability of molybdenite is depressed (Castro, 2012; Laskowski, Castro, and Ramos, 2014)."

Jan 1, 2017

By D. Lusinga

Hydrocyclones are a common feature in almost all mining operations in the world, serving mainly as classifiers. Some of their advantages include low capital costs, low space requirements and their ability to reduce residence time in closed circuit grinding processes. Although an extensive body of literature exists for hydrocyclones, these devices are still inherently inefficient, and more research is currently being undertaken, particularly in the field of modelling. In the vast body of hydrocyclone literature published so far, there has been little or no effort devoted to analysing the effect of the cone force ratio on the performance of hydrocyclones. The cone force ratio is defined as the ratio of the spigot to the vortex finder diameter (Shah, 2005). In this study a total of 44 tests was carried out in a custom-built rig at the University of Cape Town. These tests were aimed at evaluating the effect of the cone force ratio on the performance of as mall diameter hydrocyclone. The cut size and water split were used as the criterion for evaluating the performance of the hydrocyclone. Results from the tests showed that the cut size decreased with an increase in the cone force ratio. The cut size also appeared to decrease as the calculated locus of zero vertical velocity (LZVV) shifted inwards. The water recovery to the underflow appeared to increase with an increase in the cone force ratio. The effect on the cut size of adjusting the cone force ratio was found to be higher for a coarser feed than it was for a finer feed.

Jan 1, 2009

By F. N. F. le Roux

This paper describes the method used for excavating the upper 33m of emergency access shaft E2 for the underground single track tunnel running between Park and Rosebank station of the Gautrain Rapid Rail System. The soil was decomposed shale and diabase from the Witwatersrand Supergroup. The location was in the car park of The Wilds (a public park) in Johannesburg. The method proved very simple and required less complex plant and equipment than normal when excavating the shallow soil sections in shafts. It involves driving steel sheets ahead of the shaft sump into the soils and then excavating inside the ?tub? created by the sheets whilst supporting the sheets above with regularly spaced circular Steel Rings. It is the intent of this paper to discuss the method and design approach to the method. This will be done at the hand of experiences at E2 shaft..

Jan 1, 2009

By F. N. F. le Roux

This paper describes the method used for excavating the upper 33m of emergency access shaft E2 for the underground single track tunnel running between Park and Rosebank station of the Gautrain Rapid Rail System. The soil was decomposed shale and diabase from the Witwatersrand Supergroup. The location was in the car park of The Wilds (a public park) in Johannesburg. The method proved very simple and required less complex plant and equipment than normal when excavating the shallow soil sections in shafts. It involves driving steel sheets ahead of the shaft sump into the soils and then excavating inside the ?tub? created by the sheets whilst supporting the sheets above with regularly spaced circular Steel Rings. It is the intent of this paper to discuss the method and design approach to the method. This will be done at the hand of experiences at E2 shaft..

Jan 1, 2009

The AMIRA Code of Practice and Guidelines for Metal Accounting was developed in response to demand from a number of sponsor companies, including one major platinum producer. Since its publication in 2007, the Code has become widely accepted in the mining industry world-wide as a guide for best practice in metal accounting. With the changes in the structure of the platinum mining industry in South Africa over the last 10?15 years, in particular, the starting up of a number of small platinum producers who must have their concentrate smelted and the contained valuable metals refined by third parties, the need for metal accounting systems that are accurate and have an acceptable level of precision has become even more critical to the success of a platinum-producing operation. The current state of metal accounting in the industry is discussed, and possible areas for improved accounting and associated metallurgical efficiencies are identified.

Jan 1, 2013

By P. N. Lategan

Mining companies are challenged with increased difficulty in delivering capital projects on schedule and within budget. In 2005, PricewaterhouseCoopers global review of major capital projects in the mining industry only 2.5% of projects could be defined as successful when assessed across the four critical dimensions of scope, cost, schedule and business benefits. Thus 97.5% of major mining capital projects were not successful according to the criteria PricewaterhouseCoopers used. Normally if a project fails on all these criteria it indicates scope creep. Scope creep refers to the change in a project's scope after the project work has started. As a result, the projects drift away from their original design, timeline, and budget, and as a consequence destroy business benefits. The major reasons for scope creep are poor change control and the lack of proper front end loading. Change control and front end loading are based on project processes in the planning and monitoring & control process group of the Project Management Body of Knowledge1 (PMBOK). This paper will focus on key factors to consider during project scheduling/planning with special reference to cost and schedule (using Microsoft Project as a tool although the principal is universal)

Jan 1, 2009

By J. M. A. Geldenhuis

This work is concerned with studying possible reactions in the ilmenite furnace which may control the product quality of both slag and metal. Two different approaches were followed: comparing actual furnace slag compositions with the calculated equilibrium values and using commercial oxygen probes to measure the effective partial oxygen pressure in the slag and metal. It appears from a comparison of actual furnace slag compositions (in terms of the distribution coefficient of vanadium) with equilibrium values, that the TiO1.5-TiO2reaction may fix the effective partial oxygen pressure for the vanadium reaction. This possibility was tested using commercial oxygen probes (traditionally applied during steelmaking) to measure the effective oxygen partial pressure of both the slag and liquid iron in Iscor?s 3MVA pilot plant ilmenite furnace. From these measurements, it appears that commercial oxygen probes containing zirconia solid electrolytes can be used to measure the effective oxygen potential of both the slag and liquid iron. This oxygen activity correlates well with the FeO content of the slag. The results, furthermore, clearly illustrate that equilibrium conditions are not attained in the ilmenite furnace during the production of high titania slags, since the effective oxygen potential of slag and metal differ substantially.

Jan 1, 1999

By T. Lindstad, V. Myrvågnes

In the production of high silicon alloys, carbonaceous materials like coal, coke, charcoal and woodchips are utilized as reducing agents. Primarily based on historical prices of charcoal compared to fossil reduction materials, the Norwegian Ferroalloy Industry has mostly been using coal and coke (char) as carbon source. The most important role of the carbonaceous material is to react with the SiO gas to produce SiC. The ability of the reduction materials to bind SiO gas can be measured and the value is recognised as the reactivity of the carbon source. This reactivity is one of the most important parameters in the smelting process in order to obtain a high yield of metal. The reactivity of the carbon materials is directly correlated to the material properties. It is known that the rank of the coal influences the SiO reactivity where low rank is beneficial. Coals of the same rank have however proven to have varying reactivity. In order to investigate how the micro-constituents of coal influence the reactivity towards SiO gas, three single seam unwashed coals of different origin which fulfil the requirements of the Norwegian Ferroalloy producers have been chosen. As the structure in the carbonized product is a function of petrographic constitution and carbonization parameters, the coals have been separated into different density fractions. The various density fractions of the same coals proved to have significantly different petrographic composition. The coals were carbonized according to a procedure simulating the conditions the coals experience when charged to an industrial furnace. Chemical-, physical- and petrographical properties of both the coals and the resultant chars have been thoroughly examined and correlated towards the SiO reactivity.

Jan 1, 2007

A comprehensive review of ore pass records, from ten Quebec underground mines, indicated some of the limitations of available design tools to predict the occurrence of ore pass interlocking hang-ups in metal mines. The Distinct Element Method was used to perform a series of numerical experiments in order to investigate the influence of ore pass geometry, rock fragments shape and size distribution on material flow in an ore pass. Guidelines have been developed to help limit the occurrence of interlocking hang-ups in an ore pass. The proposed guidelines were evaluated with respect to field observations. Ein kompletter Bericht der Erzrollezeichnungen, von 10 Quebec unterirdischen Gruben, hat einige der Beschränkungen der vorhandenen Designwerkzeuge angezeigt, um das Auftreten Erzrolle der blockierenhang-ups in den Metallgruben genau vorauszusagen. Eine Reihe numerische Experimente mit der eindeutigen Element-Methode, wurden aufgenommen, um den Einfluss von Erzrollegeometrie, Partikelform nachzuforschen und Felsenkorngrößenverteilungen auf Materialfluss in ein Erz überschreiten. Dieses hat zu die Entwicklung der Richtlinien geführt deren Implementierung das Auftreten der blockierenhang-ups in eine Erzrolle begrenzen sollte. Die vorgeschlagenen Richtlinien wurden in Bezug auf Labor- und Feldbeobachtungen ausgewertet. Une revue de la performance actuelle des cheminées à minerai dans 10 mines souterraines du Québec a indiqué les limites des outils de conception servant à dimensionner les cheminées pour minimiser le nombre d’accrochages par enchevêtrement rocheux. Des séries de modélisations numériques, utilisant la méthode des éléments distincts, ont été réalisées afin d’évaluer l’influence de la géométrie des cheminées, de la forme des fragments rocheux et de la distribution granulométrique sur l’écoulement du matériel dans les cheminées. Cet exercice a permis de développer des lignes directrices pour le dimensionnement des cheminées afin de limiter l’occurrence d’accrochage par enchevêtrement rocheux. Les lignes directrices proposées ont été évaluées en fonction des observations effectuées sur le terrain.

Jan 1, 2003

By J. A. Cruise

With the end of the official apartheid legislation in the early 1990s, South Africa was heralded as a non-racial country. However, racial awareness has been reintroduced into the country with the Affirmative Action and Black Economic Empowerment legislation. Gender and racial transformation are the current order of the day. All organizations are required to reflect in their make-up the demographics of the population as soon as possible. Scorecard shave been drawn up to measure the rate of transformation for gender and race in organizations. The mining industry in South Africa has been in the forefront of this transformation legislation and scorecards. This paper seeks to show the effect of gender and racial transformation on mining engineering education and professionalism by analysing the changing demographics of graduating mining students at both the South African universities offering a degree in mining engineering, the professional registration of mining engineers with the Engineering Council of South Africa (ECSA), and the membership of the Southern African Institute of Mining and Metallurgy (SAIMM), the vocational institute for mining engineers. It also demonstrates the absurdity of gender and racial quotas based solely on the demographics of the current population of the country. This paper shows the degree to which mining engineering has transformed in both gender and race.

Jan 1, 2011

By S. Witzke, J. Lehmann, H. Gaye

The modelling work presented here concerns Ni-bearing steels produced by Imphy Ugine Précision. In such grades, the contents of elements such as silicon or titanium must be precisely controlled by slag/metal treatments. The slag phase is described by IRSID slag model that has been slightly revised in order to better fit recent SiO2activity measurements in the low SiO2content domain of the CaO-Al2O3-CaO system. The metallic alloys are described by the unified interaction parameter model (UIPM). In this formalism, the interaction coefficients, giving the effect of nickel on Al, Si, Mn and Ti activities, have been determined by electrochemical measurements and/or extracted from industrial data on slag/metal treatments concerning a wide range of alloy compositions: [ ] Keywords: slag, Ni alloyed steels, activities, interaction coefficient

Jan 1, 2004

By D. F. Malan, M. Grave, J. A. L. Napier

Previous fundamental research projects have indicated the value of continuous closure measurements in deep tabular excavations for improved support design, hazard assessment and for quantifying the effect of seismicity on stope closure. This paper describes further measurements in a VCR stope to validate some of the earlier findings. Calculation of the closure ratio showed that it is a good measure to identify different ground conditions and possible hazards. This work was supported by numerical modelling results, which showed that the closure ratio is very useful in discriminating the response of different geotechnical environments. Des projets précédents de recherche fondamentale ont démontré la valeur de mesures continues de fermeture dans le cas de profondes excavations tabulaires pour une conception améliorée du soutien, de l’évaluation du danger et pour quantifier l’effet de la séismicité sur l'affaissement du toit d’un chantier d’abattage. Le présent document décrit d’autres mesures dans un chantier d’abattage VCR afin de valider certaines des conclusions précédemment formulées. Le calcul du degré d'affaissement montre qu’il y va de soi d’identifier différentes conditions de sol ainsi que les dangers possibles. Les présents travaux ont été confirmés par des résultats de modélisation numérique, lesquels ont démontré que le taux d'affaissement est très utile quant à discerner la réponse dans des environnements géotechniques différents. Vorherige Forschungsprojekte haben den Wert von kontinuierlichen Setzungsmessungen im tiefen Sudafrikanischen Strebabbau angedeutet, vor allem fur Ausbaudesign und Risikobewertung, als auch fur die quantitative Bestimmungen der seismizitatsabhangigen Setzung. Dieses Referat beschreibt weitere Messungen in einer VCR Grube um fruhere Bestimmungen zu bewerten. Dass errechnete Konvergenzverhaltniss erweiste sich als eine gute Massnahme zur bestimmung von geotechnischen Zonen und moglichen Risiken. Numerische Analyse unterstutzte die vorliegende Arbeit und deutete darauf, dass das Konvergenzverhaltniss sehr brauchbar ist um Verhaltensunterschiede der geotechnischen Zonen zu erproben

Jan 1, 2003

By G. Coetzer

"Prior to operating a non-recovery coke pilot plant, it was critical to ascertain coal cake stability during the loading of a 1 m3 coal cake into the oven. Various compaction parameters were verified and established on a small laboratory-scale compaction machine to obtain a coal cake of acceptable stability. These parameters include cake density, cake surface moisture, transverse strength (force applied perpendicular to the original compacted coal cake layers), and applied force to the coal cake. This work determined the behavioural characteristics of the coal while being compacted either with a full-sized or a 1/3-sized compaction plate in a 9 kg capacity mould. Two different coals were evaluated, namely Waterberg semi-soft coking coal (sscc) and Oaky North hard coking coal.The target wet cake density of 1 100 kg/m3 (79% of 1 400 kg/m3 relative density) was achieved for Waterberg sscc, with a particle size d50 varying between 0.6 mm and 1 mm, utilizing the 1/3-sized compaction plate in the laboratory-scale set-up, with 11.6% surface moisture and 92.2 t/m2 commercial equivalent applied force. For Oaky North hard coking coal, a wet cake density of 1 189 kg/m3 (85% of 1 400 kg/m3 relative density) was achieved at a surface moisture content of 12.3% and at a lower applied force than that for Waterberg sscc, i.e. 78.5 t/m2.Coal cakes of acceptable strength, and therefore sufficient stability for further processing, were obtained for all materials evaluated during this study.Further studies should be conducted to determine the effect of zeta potential during the compaction of coals.IntroductionExxaro Resources has successfully installed and commissioned a world-class stamp-charging horizontal 1 t electrically-heated pilot-scale coke oven at its Metallurgy Services facility. Prior to operating the coke non-recovery pilot plant, it is essential to ascertain coal cake stability during the loading of a 1 m3 coal cake into the oven. The design of Exxaro’s pilot plant is such that the coal cake is pushed inside the oven by means of a pusher plate, rather than through a ‘spoon’ feed mechanism, such as is found in industrial horizontal coke ovens. The pusher plate loading mechanism dictates that the coal cake should possess high stability and inherent strength during loading into the oven, owing to frictional forces exerted by the oven floor. In order to obtain a coal cake of acceptable stability, various compaction parameters needed to be verified and established on a small laboratory-scale compaction machine."

Apr 1, 2019

By R. M. Spang

Abstract Between the German city of Dresden and the Czech capital Prague a 4-lane highway is under con-struction. At the outskirts of Dresden it will cross the narrow and deeply eroded Weißeritz Valley by a bridge. Two twin tube tunnels under oblique angles join the bridge out of the rocky valley flanks. The different geotechnical conditions of these 4 tunnel portals, their design and construction are described within this publication. The two southern portals of the tunnel Dölzschen are situated within a vertical 65 m high former quarry slope, 25 m above the valley floor. The slope proved instable due to toppling failure and exposed serious rockfall risks. Systematic anchoring, scaling, rock bolting, netting and filling under extreme access conditions eliminated these risks. Tunnel excavation started from the slope surface without any pre-cut or conventional portal construction. The opposite northern portals of the tunnel Coschütz are situated in more gentle rock slopes. After removal of debris, excavation of the eastern tunnel started in a 30° slope striking oblique to the driving direction, without any precut, too. Because of the gentle slope inclination the cross section was not earlier completely covered by rock than 30 m behind. The western tunnel started from an optimized short, narrow and steep precut. Its flanks were stabilized by reinforced shotcrete and rock bolts. Because of the small distance between the tubes rock bolts were drilled into the cross section of the neighboring tunnel. Tunnel excavation was made by drill and blast operation, preliminary support consisted of steel arches, reinforced shotcrete and radial rock bolts. Thorough survey of the bolt’s coordinates and direction prevented them from meeting each other. Rock bolts were of the permanent type to prevent the final lining from being obliquely loaded. Systematically arrayed measuring devices checked deformations of slopes and tunnels. Zusammenfassung Der Neubau der Bundesautobahn A 17 wird Dresden und Prag miteinander verbinden. Die vierspurige Autobahn quert westlich von Dresden das enge und tief eingeschnittene Tal der Wilden Weißeritz mit einer Brücke. An beide Brückenwiderlager schließen mit schiefwinkligem Anschnitt doppelröhrige Tunnel an, deren Portale in den felsigen Talflanken liegen. Die unterschiedlichen geotechnischen Verhältnisse, die Überlegungen für einen jeweils optimalen Entwurf und der Bau der portalnahen bergmännischen Tunnelabschnitte sind Gegenstand dieser Veröffentlichung. Die Südportale des Tunnels Dölzschen liegen in einer vertikalen, 65 m hohen Felswand, 25 m über dem Talgrund. Die Felswand erwies sich als global kippgefährdet, außerdem lagen flächig verteilte erhebliche Steinschlag- und Felssturzrisiken für Bau und Betrieb vor. Die Kippgefahr wurde durch ein Systemraster aus vorgespannten Felsankern, die Steinschlag- und Felssturzrisiken durch bergsteigerisches Beräumen mit dem Brecheisen, Felsnägel und Steinschlagschutznetze eliminiert. Der Tunnelausbruch begann von einer Vorschüttung direkt in der Felswand ohne Voreinschnitt im Schutz einer kurzen Luftbogenstrecke. Die gegenüberliegenden Nordportale des Tunnels Coschütz befinden sich in wesentlich flacheren Hängen. Nach dem Aushub einer mehrere Meter dicken Abraumhalde begann der Tunnelausbruch der östlichen Röhre asymmetrisch mit einer Luftbogenstrecke in einer spitzwinklig zur Vortriebsrichtung streichenden, 30° mit dem Vortrieb steigenden Felsfläche, ebenfalls ohne Voreinschnitt. Wegen der flachen Neigung der Böschung war der Tunnelquerschnitt erst nach 30 m vollständig überdeckt. Für den Vortrieb der westlichen Tunnelröhre mussten erst eine zwischen den Röhren vorhandene Felsnase teilweise abgetragen, die westlich anschließende zurückspringende Felswand vertikal gestellt und gesichert und Felsaushub in der rechten Flanke getätigt werden. Der damit entstehende Voreinschnitt wurde so kurz wie möglich und ohne seitliche Arbeitsräume ausgeführt. Die Sicherung der Böschungen erfolgte mit bewehrtem Spritzbeton und Felsnägeln. Wegen des geringen Abstands der beiden Röhren wurden die unteren Lagen der radialen Ausbruchsicherung durchgeankert. Der Tunnelvortrieb begann im Schutz eines geankerten Portalkranzes und ebenfalls von einer Luftbogenstrecke aus.

Jan 1, 2003

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that containsbetween 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007