Search Documents

By H. A. D. Kirsten

The professions are subject to a wide range of changing conditions, and are as a result forced to become more competitive. Although there is a need for specialization under these circumstances, no formal recognition, definition, or control of specialists exists. Some of the professions have attempted, over extensive periods of time, to resolve the issues involved, and have met with varying degrees of success. It appeared from the replies to a questionnaire sent to over one-hundred-and- .fifty professionals, that both advanced education and experiential training, are considered to be necessary qualifications for specialization. The opinion as to whether it should be lift to the individual to cal himself a specialist, or whether recognition should be based on peer review, was divided The majority did not want the number of specialists to be controlled The response to the reservation of work for specialists was ambivalent.

Jan 1, 1995

By R. N. Guest

The Tromp distribution curve was used in an evaluation of gravity separators treating a synthetic ore made up of silica and marker minerals of various relative densities. The results pinpoint differences in the concentration of particles of different sizes, and indicate how the grade of a concentrate is likely to vary with particle size. An increase in the feed rate increased the efficiency of the 'waterless' spiral concentrator that was tested, but the multiport spiral concentrator tested was more efficient. Both spiral concentrators were found to be more efficient than the pinched sluice and the shaking table that were tested. The method was found to be a useful way of evaluating gravity concentrators, but, for ease of analysis, care must be taken in the choice of marker minerals.

Jan 1, 1985

A Special General Meeting of The South African Institute of Mining and Metallurgy was held at Kelvin House, Johannesburg, on Wednesday, 20th August, 1986. Mr H.E. James (President) was in the chair and declared the meeting open at 15h45. Background The Chairman explained that the meeting had been called to consider a number of amendments to the SAIMM constitution. The proposed changes had been set out in detail in a document that had been mailed to all members on 4th July, 1986. He then briefly reviewed the background to the proposals, which is outlined in the Preface to the Annual Report (page 357 of this issue). The Chairman added that the Executive Committee of SACPE at its meeting on the 8th August, 1986, had resolved that the proposed amendments to the SAIMM constitution did comply with the requirements of Regulation RI525 dated 17th July, 1981, regarding the recognition by SACPE of a society as a Professional Engineering Institute.

Jan 1, 1986

By G. M. Wright

We are only as good as we are perceived to be by others and, whilst there is every opportunity to revise and polish our written works, there are no second chances with a spoken presentation. At every level, conferences and seminars have been metaphorical graveyards for many an academic reputation.

Jan 1, 1990

Professor G.T. van Rooyen has guided the Department of Materials Science and Metallurgical Engineering at the University of Pretoria in South Africa for the past 32 years. During this period, 54 masters' degrees have been awarded in the Department, and 17 doctorandi promoted. He has also made a major contribution to industry by his incisive analysis, relevant and practical synthesis, and his exceptional talent in innovative design. He is still active in fracture analysis, thermal fatigue, weld simulation transformation kinetics, and fracture mechanics, and continues to contribute to a better understanding of metallurgical problems encountered in practice. He has advised many companies, and has received many honours and recognitions.

Jan 1, 1994

By S. O. Choi, C. Park, C. Sunwoo

Two methods of stress measurements have been executed on the surface and underground to con-struct an oil storage cavern using hydro-fracturing and overcoring method. The first measurement has been performed to make a design of the caverns before excavating and the second to confirm the stress state during excavation. Six measurements have been carried out in the hydro-fracturing test at the depths between –17.8 and 54.5m from the sea level and a single measurement in the overcoring test in a single borehole at the depth of –21m from the sea level. The ratios of the maximum horizontal to vertical stress measured using hydro-fracturing and overcoring method are 2.95 and 3.1, respectively. Also, the orientations of the maximum horizontal stress are N53E and N58E. These measurements show that both methods give almost same results and significant horizontal stresses are acting on this cavern. Deux méthodes de mesure de contrainte ont étè exécutées sur la surface de terrain et sous la terre pour construire une cavité de stockage de pétrole en utilisant l’hydro-fracturing et l’overcoring. La première mesure a étè faite pour le plan des cavités avant l’excavation et le seconde pour con-firmer l’état de contrainte durant l’excavation. Six measures ont étè faites dans le teste de l’hydro-fracturing à la profondeur entre –17.8 et 54.5m depuis l’élèvation maritime. Une seule mesure a étè faite dans le teste de l’overcoring dans une seule trou de songdage à la profondeur de –21m. Le ratios de la maximale contrainte horizontale à la contrainte verticale mesure par les deux méthodes sont 2.95 et 3.1, respectivement. Les orientations de la maximale contrainte horizontale sont N53E et N58E. Ce montre que les deux méthodes donnent presque m me résultats et la contrainte im-portante est activée sur ces cavités. Zwei Druckmessungen wurden durchgeführt auf der Erdoberfläche und im Innern von Ölspeicher-kavernen unter vergleichender Anwendung des Hydrofraktionierungs- und des Kernbohrungsver-fahrens. Die erste Messung wurde durchgeführt um einen Plan der Kavernen vor der Herstellung zu erstellen und die zweite um die Druckverhältnisse während der Bohrung zu überprüfen. Sechs Messugnen wurden mit der Hydrofraktionierungsmethode bei einer Tiefe von 17,8m und 54,5m unter dem Meeresspiegel und eine einzige Messung mit der Kernbohrungsmethode in einem Bohr-loch bei einer Tiefe von 21m unter dem Meeresspiegel vorgenommen. Das Verhältnis von maxi-malem horizontalem zu vertikalem Druck bei der Hydrofraktions- und der Kernbohrungsmedthode ist 2,95 bzw. 3,1. Die Bezugspunkte des maximalen horizontalen Drucks in beiden Verfahren sind N53E und N58E.

Jan 1, 2003

By M. B. Cortie, J. H. Potgieter

An account is given of the production of three types of experimental high-chromium duplex stainless steel. The alloys had chromium contents of 22, 29, and 35 per cent. The partitioning of the main alloying elements between the austenite and ferite phases was determined, and the effect of the alloying elements chromium, nickel, and molybdenum on the mechanical properties and corrosion resistance of the duplex stainless steels is summarized. The phase compositions of the different duplex stainless steels were measured by different techniques, and the values obtained were correlated. The cracking occasionally observed during the thermo mechanical processing of these alloys was studied, and is explained as being the result of known embritlement processes.

Jan 1, 1990

SACPE has asked the Journal to bring the following points to the notice of members who are about register with SACPE. When to Apply There is no set time to apply for registration. Engineers should apply when they believe that their training has met all the requirements of Policy Statement No. 1/3. Pitfalls Remember that it is the applicants' training that must be evaluated, and this requires the avoidance in the application of vague generalities such as 'My duties were design plant including its economic evaluation' or 'I was engaged in . . Requirements An example of what is required can perhaps best illustrate the point.

Jan 1, 1982

By M. J. Daly

Historically, engineers and scientists, particularly those involved in the coal-mining industry, have been slow to adopt statistical methods. However, the need to obtain the maximum information .from expensive exploration and development programmes, and the current focus on total quality management, have led to a change in perceptions if classical statistical and geostatistical methods and their application as planning tools. Some if the underlying issues associated with the generally poor communications between statisticians and engineers/physical scientists, which contribute to some if the misconceptions relating to statistical methods, are discussed The potentially profitable application if a number if statistical techniques in the fields if geological evaluation and mine planning! development is also reviewed, with specific reference to the coal industry.

Jan 1, 1995

By J. H. Bulloch

The paper gives an assessment of the available data on the linear elastic fracture mechanics involved in stress corrosion cracking and in the behaviour of reactor pressure-vessel materials exposed to a simulated pressurized water-reactor environment. As a result of the different experimental techniques used in the various studies mentioned, only a few detailed conclusions can be drawn. The data from constant-displacement wedge-opening loading (WOL) tests, with the exception of one study, exhibited very limited or no crack extension during exposure periods of up to 14000 hours. The data from constant-load tests indicated evidence of crack extension, but the nature and extent of the crack extension are still unclear. When crack extension did occur, it was exclusively transgranular in nature. Certain differences in the available test data are tentatively explained in terms of the experimental procedures used, and the need for a consistent code of experimental techniques is highlighted.

Jan 1, 1987

By P. C. Schutte, J. R. Smith

The objective of ergonomics is to enhance the effectiveness and efficiency with which human tasks are carried out. Furthermore, the objective is to improve desirable human values. This can be achieved by enhancing safety, reducing fatigue and stress, increasing comfort, increasing job satisfaction, having greater user acceptance and thereby improving the quality of life. Mechanization has influenced the prevalence of injury, mainly due to the application of human physical effort as the power source. With mechanization, the operator’s function is now essentially one of control rather than being an energy source, however the risk of injury has not diminished. Mechanization in itself has introduced inefficiencies, health risks and physiological stress. The major objectives of ergonomics are discussed through examples of acceptable and less successful implementation of ergonomics within mechanized mining. The influence of the machine system on the human is addressed and practical solutions to improve and optimize the interaction of the human and the machine are outlined. Furthermore, practical examples of control and display integration, anthropometric and biomechanic influences on design, orientation, posture and stereotypes are used to accentuate the advantages of the application of sound ergonomics principles to the specialised area of mechanized mining.

Sep 1, 2001

By R. J. Kriek, J. J. Cruywagen, W. J. Engelbrecht

Selective photo reduction, using the semiconductor TiO2 under UV irradiation, has been investigated as a possible recovery and/or separation method for the PGM's rhodium, palladium and platinum. The effect of pH value and concentration of the sacrificial reducing agent (ethanol) on the rate of reduction of Rh (III), Pd (II) and Pt(IV) ions have been determined separately for these ions as well as for some mixtures. Conditions favourable for the reduction and adsorption (or precipitation) on TiO2 have been established. It has been found that already deposited Pt or Pd metal promotes reduction of Rh (III) ions at a pH value where it would not otherwise be reduced. A method for the separation of a mixture comprising Rh (III), Pd(II) and Pt (IV), based on photo reduction and adsorption on the TiO2, is proposed.

Jan 1, 1995

By S R Grano

A fundamental model, which considers the subprocesses of particle collection by bubbles in flotation, is applied to two comprehensive flotation surveys in the rougher stages of C3 concentrator, PT Freeport Indonesia. The flotation surveys focused on the collection of: ? cell-by-cell and size-by-size metallurgical, ? cell hydrodynamic, and ? pulp and surface chemistry information. The two surveys were conducted at significantly different feed tonnages, giving rise to significantly different feed particle size distributions, pulp densities and mean pulp residence times. A series of model simulations are performed with the aim of quantifying changes in copper recovery, on both a size-by-size and unsized basis, with changes in values of the hydrodynamic parameters and hydrophobicity of the copper sulfide mineral. This was carried out in an effort to identify the most promising route to increase overall copper recovery in roughing. It was found that by increasing the hydrophobicity of the copper sulfide mineral surfaces it became possible to optimise cell hydrodynamics, which targeted increased fine (-12 µm) copper sulfide mineral recovery but without adversely affecting coarse (+150 µm) copper sulfide mineral recovery.

Jan 1, 2007

By J. C. Paynter

A review of copper hydrometallurgy by J. C. PAYNTER, B.Sc. (Chem. Eng.) (Visitor) Copper hydrometallurgy is discussed with special reference to the treatment of chalcopyrite concentrates under South African conditions. The following processes are described and illustrated: Sherritt Gordon's ammonia pressure leachilng, the Arbiter Process, sulphuric acid pressure leaching, roasting processes, the Cymet Process, and the ferric chloride process developed at the National Institute for Metallursy. These processes are then compared with respect to the form of sulphur produced (elemental sulphur or sulphate), the character of the iron product and the handling of different types of ore.

Jan 11, 1973

By K. R. Vost

Variation in air temperature in a cross-section of an underground airway by K. R. VOST, B.Sc. (Glas.), M.Sc. (N.S.W.) (Visitor) Measurements of air temperatures in underground airways are normally made at only one point in a cross-section, and the air tem peratures at other points in the cross-section are assumed not to differ significantly from this. This paper discusses measurements made at a number of points in fifty crosssections in airways with different air velocities and wetness of floor. These measurements show that significant variations of air temperature can occur in a given cross-section at a given time. The effects of such variations on the accuracy of measurement of rises in air temperature as air passes along an airway are discussed. The importance of considering experimental error in the measured rises in air temperature when attempting to validate theoretical and empirical methods of predicting such rises is also discussed.

Jan 7, 1976

Die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie het 'n paar jaar gelede 'n toekenning vir voortreflike akademiese prestasie deur vierdejaarstudente aan technikons ingestel. Disinvestment campaign by COLIN M.SPENCE As President of the Federation of Societies of Professional Engineers, which is an organization representing twelve institutions of the engineering profession comprising over 18 000 engineers of all kinds-of whom over 15 000 are either professional engineers or engineering graduates-I have been asked to make a statement on the disinvestment campaign on behalf of the profession.

Jan 1, 1985

1. OPLEIDING IN INGENIEURSWERK VIR IN G ENIEURS- IN -OPLEID IN G 1.1 llegistrasie as Ingenieur-in-opleiding 'n Gegradueerde ingenieur wat in 'n eksamen geslaag het wat die Raad erkenl, is registreerpaar as 'n ingenieur-in-opleiding kragtens die Wet op Professionele Ingenieurs2. Aansoekvorms kan van die Registrateur verkry word. Mineral processing congress The XIIIth International Mineral Processing Congress is to be held in Warsaw from 4th to 9th June, 1979. Seeing that by products and co-products are becoming of increasing importance in mineral processing operations, the theme of the Congress is to be the 'Treatment of Raw Materials with Total Utilization of All Constituents'.

Jan 1, 1979

By J. H. Bulloch

This paper describes detailed fractographic analyses of several specimens that had undergone corrosion-fatigue tests at high stress ratios in simulated pressurized water-reactor environments. The distribution and morphology of non-metallic manganese sulphide inclusions are shown to strongly affect the growth of environmentally assisted cracks (EAC), and certain features suggest that a hydrogen-assisted mechanism is responsible for the observed EAC growth. The incidence of transient EAC growth in isolated regions suggests that the critical conditions that trigger this type of growth are the 'right' local chemistry at the crack tips and imposed mechanical conditions.

Jan 1, 1987

By R. J. Gordon, N. J. Keys, N. F. Peverett

Photometric sorting of ore on a South African gold mine by N. J. KEYS. B.E. Met. (Queensland) (Visitor). R. J. GORDON. (Visitor). And N. F. PEVERETT. B.Sc. (Eng.) (Wits) (Fellow) This paper concerns the development and application of a high-throughput, multi-stream photometric sorting machine developed for the South African gold mines. It is now believed that this sorter and its progeny may be found suitable for a large proportion of all possible sorting applications. A laser-light source and sensitive photomultiplier are employed in a scanning system to detect light reflected from the surfaces of rocks passing through the sorting zone. Electronic circuitry then analyses the photomultiplier signal, which represents the varying intensity of the reflected light, and produces control signals to actuate the appropriate valves of an array of air-blast rejection devices to remove from the feed certain particles selected by the analysing process. Typical throughput per machine ranges from 50 t/h for a minus 60mm plus 30mm feed to 200 t/h for minus 150mm plus 70mm material.

Jan 9, 1974

By G. J. Wright, M. J. Neale

As machines become more complex and vital to our way of life, any disturbance or failure of their proper functioning tends to have serious consequences. To prevent such failures, increasing attention is being paid to techniques for the monitoring of machinery condition or 'health'. Of the many methods available, examination of the lubricant and any particles it contains forms a basis for interpretation of the conditions of operation, and the rate and severity of degradation of the moving parts, in a machine. Many techniques of wear-debris analysis, such as spectrographic oil analysis and ferography, are available indicate the composition, shape, size, and concentration of contaminants in a lubricant. This paper reviews the important aspects of wear-debris analysis as an integral component of machinery condition monitoring, and gives an insight into the selection of appropriate techniques and the information that can be obtained from each.

Jan 1, 1987