Search Documents

By M. F. G. Bruce

Two backfill systems have been developed on West Driefontein, namely the centrifuge dewatered tailings system and the cyclone-classified tailings system. Modifications to the two systems since the publication of the original paper (Close and Klokow, 1985) are discussed in addition to the results obtained. Considerable experience has been gained from the operation of the centrifuge dewatering units as well as the placement of dewatered tailings in a difficult mine environment. The centrifuge dewatered tailings method has proved successful in the extraction of a highly stressed block of ground at No. 5A Sub-vertical Shaft. The utilization of backfill support in this area made it possible to dispose of a high-grade barrier pillar. This pillar was considered necessary prior to the introduction of backfill support. The recovery of the gold from this pillar made the use of dewatered tailings backfill cost- effective, despite high labour and maintenance costs. Current experience with the bagfilling method of placing cyclone- classified tailings indicates that it is viable and requires considerably less capital investment. Although expensive at present, it is envisaged that costs will decrease once cheaper bags and other forms of stope support are used. The placement of backfill in small-diameter sausage-type bags requires no change in mining cycle and allows the backfill to be placed close to the stope face. Both backfill systems are being expanded but preference is to be given to the cyclone-classified tailings system.

Jan 1, 1988

By M. Le Roux

The dewatering of coal, and particularly fine coal, continues to challenge coal prepatration engineers to find a cost-effective solution. With known world oil reserves being depleted daily, it is envisaged that the future price of coal may justify the use of thermal drying to achieve lower coal product moisture levels. The effect of exposure of the coal to elevated toemperatures on the mechanical strength of the coal was investigated. It was found that temperature does not play a major role in determining the volume breakage of a particle and that other variables such as orientation during impact has a much greater influence. A double breakage mechanism was reported during the grindability tests. Surface, as well as volume breakage, occurs for the first 4 minutes while only surface breakage takes place thereafter. Due to this double breakage action, it was found that exposure to temperature does play a role in the amount of breakage and breakage rates during grindability tests. It was also concluded that a particle will break to an optimum size due to impact, after which only its surface will grind away as it is subjected to breakage forces.

Jan 1, 2008

By M. Thurston

This case study shows that for a set of lognormal data with a low coefficient of variation the semi-variogram of the logs has almost the same shape as the semi-variogram of the raw data. This means that the variogram of the logs, which is numerically more stable, can be used to krige the raw data. This technique is tested on samples from a sedimentary gold deposit and the results compared to those obtained from ordinary and simple lognormal kriging.

Jan 1, 1987

By Arvi Parbo

I would like to use the occasion to reflect on how the world environment for the minerals industry is undergoing substantial change, and how this change may affect the industry. I have given my talk the title 'The Quest For Competitive Edge', because the net effect of the changes taking place is that competition is increasing. To set the scene, let us look back at the situation which has existed in our industry in the past.

Jan 1, 1993

By H. M. Wells

The investment decision under uncertainty by H. M. WELLS, Pr. Eng., M.Se. (Fellow) The future outcome of a proposed investment is uncertain at the time the decision must be made to accept it or reject it. This uncertainty can be expressed in the form of a probability distribution. An attempt is made to rationalize the investment decision under these circumstances, especially when the range of possible outcomes extends into both the acceptable and unacceptable domains. A rigorous definition of risk is proposed, and a criterion of risk aversion is developed that forms the boundary between acceptable risk and unacceptable risk (called the loss limitation line). It is shown that this decision criterion can also serve as a quantitative yardstick in the evaluation of various possibilities for 'tailoring' the proposal to mlke it more compatible with the particular financial circumstances of the company concerned.

Jan 4, 1976

By R. E. Gundersen

Hydro-power-the use of high-pressure water as an energy source-offers tremendous benefits for environmental control in deep, hot mines. The extent of these benefits depends on the mining method, the selection of equipment to be hydro-powered, and the efficiency with which the coolth is extracted from the water and into the working environment. The engineering of hydro-power systems continues to receive much attention. However, this paper considers the environmental implications of using hydro-powered equipment, particularly with regard to positional efficiency. The integration of hydro-power with developments such as backfill, mechanization, and higher face-advance rates is discussed. Layouts are proposed that attempt to minimize the quantity of water in circulation by extracting the maximum coolth from the water.

Jan 1, 1990

As a token of their gratitude, former pupils of Professor Lucien Denoel, a lecturer on coal-mining in the University of Liege, over a period of forty years, have founded the LUCIEN DENOEL prize. It is awarded, regardless of nationality and diplomas, to the author of a thesis dealing with coal-mining, ventilation, mine-draining methods, the use of explosives in the mine or coal-preparation. The thesis must show a truly scientific approach and considerable originality, and must not have been dealt with in a previous publication. The prize is 60.000 Belgian francs. The articles must be written in French, Dutch, German or English, and contain not more than 10,000 words, figures included. They must be forwarded, in triplicate, to the 'Jury du Prix Lucien DENOEL, c/o A.I.Lg., 22, rue Forgeur, Liege, Belgium,' before 1st July, 1970. The examining board reserves the right to publish the winning thesis in a Belgian magazine.

By B. M. Van Vliet

SYNOPSIS This paper outlines the principles involved in the regeneration of activated carbon for renewed use in the recovery of precious metals or the purification of water. While chemical methods are effective in restoring the activity of spent activated carbon containing only single or defined adsorbates, thermal methods have to be used when the spent carbon is loaded with a heterogeneous mixture of adsorbates such as those normally present in industrial process streams or effluents. The steps involved in thermal regeneration are described, together with the operating conditions that can be controlled to give the required degree of activation. Finally, an account is given of the structural changes that occur in a new or spent activated carbon during thermal treatment.

Jan 1, 1991

By H. G. M. Rose

Contribution to the above paper by H. G. M. Rose* (Fellow) INTRODUCTION Dr Lawrence is to be congratulated on his most interesting and instructive paper, particularly on his suggestion for a model to increase mining productivity through improved management performance. In view of an experiment initiated in one Union Corporation mine (Mine A) and later extended to a second mine (Mine B), it might be of interest to review the many human factors involved and the initial productivity results achieved.

Jan 7, 1974

By L. M. Falcon

Cassiterite is considered to be the only economically significant tin mineral in the earth's crust. In its purest form, cassiterite contains 76 per cent tin. The mineral is hard and heavy but also extremely brittle. and is therefore ideally suited to gravity recovery techniques. Cassiterite deposits can be categorized into two main types, i.e. alluvial or 'soft' rock deposits, and 'hard' rock deposits. The former are relatively simple to upgrade owing to their relatively coarse nature and their high degree of liberation. Hard-rock deposits, on the other hand, require considerably more sophisticated gravity methods to achieve the required degree of beneficiation. Various types of gravity recovery devices, both old and new, are described, and their respective roles in the flowsheets used are illustrated.

Jan 1, 1982

By M. G. Demmer

South Africa ranks among the top three mineral producing countries in the world, and yet the country's teaching and student population have a very limited knowledge of the mining and metallurgical industry. This is probably one of the major reasons why so few scholars elect to study mining-related disciplines at local universities, or to consider a career in the industry. Small mines Much interest in the development of small mines has been evident in the past few years, with junior companies taking the bull by the horns and moving in where larger companies found it uneconomic to tread or, indeed, where large companies are foresighted enough to see the advantage of smaller operations. Examples of small mines are to be found from Europe to Australia, in the Americas, and in

Jan 1, 1986

By R. M. G. Machunter

The dynamic behaviour of plant circuits and the available instrumentation determine the control strategies that are appropriate for the duty of the mineral separation plant. Although steady state modelling is appropriate to provide the main requirements of grade and throughput capability of a plant, it is the dynamic characteristics that determine the tolerance of the plant to disturbances and also its controller ability. This paper explores these issues with respect to the additional use of dynamic modelling to achieve these objectives.

Jan 1, 2007

By D. Duncanson, R. J. Davidson, C. G. S. Schmidt, G. A. Brown, J. D. Taylor, N. W. Hanf

The development of a cyanidation route for the treatment of gold-plant gravity concentrates is described. This work was carried out as a natural consequence of earlier improvements to the recovery of gold in the gravity sections of existing gold plants. Concern about the environmental aspects of the conventional amalgamation process was further motivation in the development of an alternative procedure. It was found that the partial pressure of oxygen in solution was the most critical reactionrate determining factor. The rate of gold dissolution was shown to be controlled by the reaction rate below approximately 25°C and by diffusion above that temperature. Thus, the efficiency of pulp agitation and oxygen partial pressure permitted a high degree of control over the rate of gold dissolution. The use of oxygen rather than air significantly increased the dissolution rate of both gold and silver. The solubilities of sodium, calcium, and potassium aurocyanide complexes under simulated reaction conditions were studied, and it was established that the values for the sodium and calcium complexes were limited, requiring the use of lower pulp densities and higher reaction temperatures for the treatment of very high-grade concentrates. The presence of excessive amounts of tramp iron in such concentrates of up to 25 per cent by mass was found to result in poor gold dissolution owing to the cementation of gold under certain reaction conditions. The maintenance of high oxygen partial pressures, together with high cyanide concentrations, high pH levels, and the presence of calcium in the system, all aided in passivating the tramp iron. Copper, gold, and iron were shown to be the main cyanide-consuming elements. Optimum gold dissolution was obtained in a closed bench-scale reactor incorporating a flotation-machine type of agitator for effective pulp agitation and oxygenation, the oxygen being recirculated. The reactor was designed to operate under a very small positive pressure. After reaction times of 2 to 6 hours at temperatures in the region of 30°C, both the gold and the silver dissolution averaged 99,S per cent. In the case of very high-grade concentrates, it was shown that gold could be floated in the same reactor by drawing off the flotation concentrate through a port in the reactor. A flotation recovery of 87,4 per cent of the gold in 3,9 per cent by mass was obtained. The recovery of osmiridium from cyanide-leach residues and the electrowinning of gold from the pregnant liquors were also considered as processing aspects in the treatment of gold-plant belt concentrates. Final table tailings with a gold concentration of 10to 12 gft were obtained. The results of the investigation strongly suggested that an alternative cyanidation route for the treatment of gold-plant concentrates was technically feasible, provided the system included effective agitation and oxygenation. In the case of lower-grade concentrates, cyanidation followed by the electrowinning of gold appears to be the simplest route, while, for high-grade concentrates, flotation and smelting of the concentrate followed by cyanidation of the flotation tailings are suggested. The use of oxygen rather than air for sparging the pulp would depend largely on the grade of material to be treated. A preliminary comparison of the costs related to the amalgamation and cyanidation processes for the recovery of gold from such concentrates indicated very similar capital and operating costs. It was concluded that other considerations, e.g. toxicity, safety, and lower labour requirements, were more important than such small cost differences. Furthermore, the 'opening' of the gold-plant gravity circuit, which would be made possible by a cyanidation route, would further reduce the operating costs because of the subsequent decrease in the tonnage to be treated.

Jan 1, 1978

A brief overview is given of the issues regarding the processing of waste electrical and electronic equipment (WEEE). The printed circuit board component of WEEE is an exceptionally complex feed to possible recycling processes. Scrap printed circuit boards were selectively smelted at 1 200°C to produce a metallic alloy. Iron and aluminium were found not to be part of the alloy. The alloy was characterized by SEM-EDS, and three phases were identified: alpha and delta bronzes, and a lead-rich phase. Calculations show that about 56 mass per cent of the alloy is the alpha phase, 35 per cent delta phase and 9 per cent lead phase. A simplified approach using appropriate binary phase diagrams was used to derive a phase composition for the alloy. This was further backed by FactSage calculations, which showed that the simplified approach was appropriate for this alloy. The experimental findings and theory were found to agree well.

Jan 1, 2009

By A. Hinde, M. H. Moys

Tailings from metallurgical plants, when deslimed with hydrocyclones, provide a valuable source of material for the backfilling of mines. The effectiveness of this material as a support medium is a sensitive function of its particle- size distribution and water content. It is therefore important that the hydrocyclone-classification plants used to prepare the backfill are operated efficiently, and that the effects of feed disturbances on the composition of the backfil are minimized. This paper addresses the problem of the design, control, and optimization of classification plants to satisfy this need. The development of a computer program to simulate the dynamic behaviour of a hydrocyclone circuit of any given configuration is described. The use of the simulator to investigate the relative performance of conventional and innovative control strategies for single-stage and two-stage circuits is discussed in depth. The results of simulation studies are presented that indicate there is considerable scope for improving the performance and cost-effectiveness of backfill-classification plants.

Jan 1, 1991

By D. G. Keefe, I. C. Robinson

In this paper the authors present their views on the actual and potential role of commodity analysis in mining industry. Owing to the dominant influence of the economy on all commodity markets, it is essential that individual commodities are studied not only in depth but within the broader context of economic influences. A commodity unit, which monitors market developments in a wide range of commodities, is well placed to provide the broader perspective in the study of commodity markets. This paper describes some of the specific functions of such a unit. Some of the methods used for price forecasting are described, and the results of price forecasts by different forecasting methods are compared.

Jan 1, 1980

The paper discusses some theoretical aspects of Gy's sampling theory and provides reasons as to why it has found limited use in the mining industry, particularly for ores with low concentrations of values such as gold. These types of ores are referred to as low grade ores in the paper. It is shown that the misuse of the a priori liberation factor proposed by Gy is the main reason for the implementation limitation of Gy's model for low-grade ores. In addition, results of a case study done at the Gencor Geostatistics Department based On the new implementation of Gy's theory are provided.

Jan 1, 1996

By C. A. Cousins

Platinoids in the Witwatersrand system C. A. Cousins. (visitor) Study of the composition, nature and mode of occurrence of platinoid minerals in the conglomerates of the Witwatersrand System leads to some interesting conclusions. Genetic evidence strongly favours a placer origin, while comparison with modern alluvial platinoids supports this view but also indicates that they are very mature alluvials. The compositional patterns and distribution of the platinoids in the Witwatersrand basin suggest the water was saline. Study of the mineralogy was greatly facilitated by the electron-probe.

By D. F. Williams

The modelling, simulation, and design of processes for the recovery of gold from solution by absorption on carbon require the combination of a suitable rate expression with a description of the flow conflguration of the system. By the use of a suitable rate expression from the literature, methods are presented for the design of multi-stage countercurrent absorption systems corresponding to the commonly used carbon-in-pulp and carbon-in-column contacting systems. The sensitivity of the recovery to various design parameters is illustrated. These results have important implications in the choice and design of equipment.

Jan 1, 1985

By A. B. Holland-Batt

The application of Reichert spirals and cone concentrators within the South African mineral industry is discussed, and the procedures used in the acquisition of design data are outlined. Computing techniques developed by Mineral Deposits Limited for the processing of test data for use in the design of production circuits are described.

Jan 1, 1982