Search Documents

By H. D. Mtegha

Mining is important to the economies of both Tanzania and Namibia. Recently, both nations revised their national mineral policies to ensure future economic benefit. The main difference in the mineral policy-formulation processes followed by the two countries is identified as the degree and timing of stakeholder involvement during the articulation process. In the case of Namibia, the stakeholders were involved from the start in identifying issues and in suggesting policy solutions. In contrast, the Tanzanian process involved stakeholders after a framework had been developed by a task team. The Tanzanian emphasis was on attracting foreign investment into a traditionally state enterprise system of mineral investment and development. One can argue that the policies developed met the initial requirements, and both are, therefore successful, despite the different processes of policy formulation that were used. However, several fundamental questions arise as a result of the two approaches. This paper attempts to answer these questions by providing a comparison of the processes used for developing and formulating the mineral policies of Tanzania and Namibia. It concludes that the Namibian consultative process is perhaps more sustainable in the long-term because of its wider public support. Time will tell which of these policy-formulation processes provides a basis for sustainable economic growth for developing mineral economies.

Jan 1, 2010

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. STANDARDS FOR ACCEPTANCE To merit consideration papers should be of sufficient high standard and contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Their publication should be of real interest to technical men and of benefit to mining and industry. Authors must realize that because a mine shaft is new or the mine itself is newly established, this in itself does not justify a paper unless significantly new techniques or processes were involved in the opening-up procedure. A few well selected diagrams and illustrations are often more pertinent than an amorphous mass of less well chosen material. Over-statement and dogmatism are jarring and have no place in technical writing. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Papers should be submitted at least three months prior to the intended date of presentation. The text should be typewritten, double-spaced, on one side only of foolscap paper, leaving a left-hand margin of 11/2 inches, and should be submitted in duplicate to facilitate the work of the referees and editors. Galley proofs are sent to the authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. ORTHODOX SEQUENCE Title and author's name together with author's degrees, titles and position Summary, abstract or synopsis Introduction Development of the main substance Conclusions References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H. Authors' & Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarily known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. Generally: Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unamiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parenthesis ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. Abbreviations and symbols are laid down in British Standard 1991 and proof correction symbols in British Standard 1219c. Abbreviations are the same for the singular and plural, e.g. ft for foot and feet, lb for pound and pounds. Percentages are written in the text as per cent; the symbol % is restricted to tables. Likewise ft and in. should be used, x' y" only being permissible in diagrams and plans. Drawings and diagrams are to be in black India ink and should be about 6 in. wide. Numbering of tables should be in Roman numerals: 1, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the margin of the typescript where drawings and diagrams, etc. are to appear in the text. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. SUMMARY ABSTRACT OR SYNOPSIS It is most important that the summary should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be resorted to only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus . . .1 . . . 2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal.

By J. A. Wates

Stope backfilling in South African gold mines uses the coarser cyclone fraction of the gold tailings. The disposal of the overflow from the cyclones, which is finer and of higher moisture content than normal gold tailings, presents some problems. This paper describes an investigation undertaken to define the parameters that are required for a quantitative and qualitative assessment of the operation and stability of slimes dams built of such material. However, seeing the investigation was conducted on the slimes from only one mine, it is recommended that, until a wider range of data becomes available, tests should be conducted for each individual mine.

Jan 1, 1988

A method, based on the macroscopic population balance equation allowing the dynamic simulation of a multistage adsorption plant given an arbitrary rate expression, is described. The partial differential equations resulting from this method are simplified using the method of characteristics. The simplified equations can then be solved using standard ODE integration techniques. The procedure is illustrated by means of data typical of a CIP application. Requirements for data structures which allow the incorporation of the carbon-in-pulp (CIP) model (and other unit models) into a general metallurgical simulator are described. Based on these considerations, it is concluded that more generality in the description of distributed quantities such as loading and particle size is provided by the use of mass density at fixed class boundaries, rather than discrete masses within fixed classes as has hitherto been used by ore-dressing simulators.

Jan 1, 1987

By M. H. Moys, K. S. Liddell

The dynamics of the ball load within a wet-grinding mil are examined, using measurements of torque and load position, The test equipment provided an accurate torque measurement, and the toe and shoulder positions of the load were measured by the use of a conductivity probe mounted in the mill shell. Both the variables tested-mil filing and rotational speed-influence the position of the load, and hence the torque, and have interactive effects on both the torque and the load position, An increase in mil speed and filing causes the torque to increase to a maximum value, after which further increases in speed or filing cause the torque to decrease. The position of the load toe is influenced only by the filing up to speeds of approximately 80 per cent of critical, whereas the speed and filing both cause the load shoulder to rise as their magnitudes are increased, The power drawn by the mill is predicted by the use of published equations, and these values are compared with the measured power draw.

Jan 1, 1988

By J. van Zyl Visser

The advancement in Information Technology has resulted in a change in workflow practice in our Mineral Resource Management (MRM) offices on the mines and at our corporate office. This paper discusses the AngloGold approach in defining an IT strategy for MRM, a brief overview of systems usage and benefits. AngloGold has gone through a transformation phase and has positioned itself as a world-class, low cost producer. To support this objective, an initiative has been launched to provide the MRM division with an integrated MRM technical suite of systems with support of a Management Information System. Technical systems for a tabular orebody are not freely available and hence it took AngloGold almost seven years and a significant amount of capital to develop an integrated suite of technical systems. AngloGold MRM IT adopted the typical Zachman framework (value chain) approach in the analysis process and formulated the final deliverable in terms of AngloGold’s strategy. Major benefits have been realized through the ability to change planning scenarios in a short period of time and hence be able to increase reserves and NPV. The development of MRIS, which will become the flagship in AngloGold’s portfolio of systems is in phase two and this system will allow AngloGold to publish Resources and Reserves as per SAMREC and the JORC Code at will. The availability of information at all levels of the operations has made making decisions easier and hence some specialized reports such as the Basic Mining Equation were developed from the Corporate Data warehouse and from the MRM reporting database. Decision Support Systems(DSS) such as Business Objects and Oracle Express are now being used to assist in the process. The decision to use Business Objects to replace SAS reporting as the core reporting tool has resulted in the empowerment of the user and major cost saving as far as the use of consultants to set up standard reports.

Jan 1, 2003

By G. J. McDougall, M. J. Nicol, O. L. Wellington, R. G. Copperthwaites, R. D. Hancock

X-ray photoelectron spectroscopy showed that the adsorption of gold cyanide on carbon in the presence or absence of electrolytes and acids proceeds by the same mechanism. Although the identity of the gold cyanide adsorbate is not known, the mechanism appears to have an initial adsorption stage that involves the adsorption of an ion pair: Mn+[Au(CN)-2]n where Mn+ is a metal ion (for example Na+, K+ and Ca2+) that has a lower solubility than the Au(CN)-2 anion in the adsorption medium, followed by a reduction step in which either a sub-stoichiometric Au(CN)x surface species or a cluster-type compound of gold is formed.

Jan 1, 1980

Ninth International Symposium TECHNIQUES FOR DECISION MAKING IN THE MINERAL INDUSTRY The Symposium which is to be held in Montreal during the week of 14th to 19th June, 1970, follows the Computer Symposium held in Salt Lake City in September, 1969. The purpose of the Symposium is to define the role of decision-making techniques within the mineral industry and to stimulate the development of specific applications. The subject of the Symposium-mathematics, operations research and computers as applied to the mineral industry-have permitted us to structure it in such a way that a complete picture of the mineral industry in its public policy, corporate, financial and technological environment emerges. Topics for the sessions are: . The Public Policy Environment;. The role of Decision Making Techniques in the Mining Company; . Information Storage and Retrieval; . Markets-Forecasting, Patterns and Strategies;. Search for Mineral Deposits;. Quantification of Geological Variables;. The Mine Development Decision; Production Systems;. Planning, Scheduling and Control Systems. The sessions will be directed energetically by chairmen who have been in continuous contact with the authors, providing them with information about related papers and sessions. This symposium is sponsored by the Canadian Institute of Mining and Metallurgy, McGill University and Ecole Polytechnique. Further information may be obtained from: The 9th International Symposium. W. H. Gauvin, General Chairman, J. Elbrond, Programme Chairman. Department of Mining Engineering, Ecole Poly technique, P.O. Box 501, Snowdon, Montreal 248, Quebec, Canada. ACHEMA 1970 The European meeting of Chemical Engineering and the Achema Congress 1970 is being held at Frankfurt/Maine, from 17th to 24th June, 1970. The programme includes some 110 plenary and specialised lectures, numerous technical films, excursions, and technical discussions in front of the exhibits which form the central feature of the Achema-Exhibition Congress. Further information may be obtained from the honorary representative of Achema in South Africa, Mr F. Schilling, P.O. Box 31274, Braamfontein, Johannesburg. NINTH COMMONWEALTH CONGRESS PROCEEDINGS Publication of the proceedings of the Ninth Commonwealth Mining and Metallurgical Congress, 1969, is being undertaken by the Institution of Mining and Metallurgy, London. There will be four volumes covering papers presented at the Congress together with the discussion and author's replies, and the addresses by Sir Duncan and Sir Ronald Prain. These will be available April-June 1970. Special pre-publication prices apply to orders received before 1st April, 1970. Order forms may be obtained from Secretary S.A.I.M.M., P.O. Box 1183, Johannesburg. 6th World Congress on the Prevention of Occupational Risks This Congress, dealing with industrial accidents and occupational diseases, will be held in Vienna from 10th to 15th May, 1971. Further information may be obtained from: VI Weltkongress für Unfallverhütung, Postfach 745, A-1015 Wien, ÖSTERREICH. International Vacuum Metallurgy Conference 1970 The Vacuum Metallurgy Division of the American Vacuum Society is organizing an international meeting that will be held at the Convention Center in Aanaheim, California from 15th to 19th June, 1970. Enquiries should be directed to the Arrangement's Chairman, L. M. Bianchi, TRW Inc., 23555 Euclid Avenue, Cleveland, Ohio 44117, Tel. No. (216) 383-2111. AIME WORLD LEAD-ZINC SYMPOSIUM This symposium is being held from 21st to 23rd October, 1970, in St. Louis, Missouri, U.S.A., in conjunction with the Fall Meeting of the Society of Mining Engineers, and a Rapid Excavation Conference. In addition to local field trips to smelter and refinery operations there will be a number of extended trips of six to eight days. Information may be obtained from: Mr. John C. Fox, Secretary, Society of Mining Engineers of AI.M.E., 354 East 47th Street, New York, N.Y. 10017, U.S.A. NEW SUBSCRIPTION RATE TO THE JOURNAL As from 1st JANUARY, 1970, the subscription rate for the Journal has been increased from R12.00 to R18.00 per annum, i.e. R1.50 per issue instead of R1.00. The discount to booksellers is 15 per cent. COURSEOF THE THEORYOF THE UNIT OPERATION OF GRINDING The South African Institute of Chemical Engineers is arranging for Prof. L. G. Austen to conduct a course on the above subject in September, 1970. Interested persons should contact Dr G. S. Harrison, S.A. Institution of Chemical Engineers, A.E. & C.I., 15 Anderson Street, Johannesburg. METRICATION The S.A. Bureau of Standards has published a document entitled "Metric Scales and Units for use in the Building and Construction Industry." It has been compiled by the Metrication Committee of the National Building and Construction Advisory Council and is the first of the series of informatory documents relating to the programme for the metrication of the Building Act Construction Industry. This document is obtainable from the South African Bureau of Standards, Private Bag 191, Pretoria at 50c per copy.

By J. J. C. Heynike

The relationship between population growth and steel consumption since the beginning of the twentieth century is indicated, reference being made to the increasing capacity of production units and the resultant increased pollution in the same area. The need for the control of fugitive emissions with its associated high cost is pointed out. There is a direct relationship between energy and pollution, and examples are given of several improvements that have been made to achieve better energy usage and reduced pollution. Several practical examples of air-pollution control systems are described as applicable to the main metallurgical steel processes of today. In conclusion, reference is made to the fact that, with the improvements attained in reducing pollution, the public will not tolerate a decline in the standards already attained. Environmental control and better energy utilization will continue to be important aspects of steel-plant design and operation.

Jan 1, 1978

By H. E. Cross

The conversion of a uranium plant to the recovery of zinc by H. E. CROSS. B.Sc. (Eng.)(Hons.) Rand (Fellow) The conversion of the Vogelstruisbult Uranium Plant into a plant for the production of electrolytic zinc is described. The reasons for the conversion, the preliminary investigations. and the basic design principles are all outlined, and a brief account is given of operating experience.. during the commissioning of the plant, with equipment that had been put to a use for which it was not originally Intended.

Jan 11, 1973

By R. H. O?Connor, B. N. Soutar

The paper reviews the introduction 01mechanical shaft drilling into the sinking 01shafts in the Gold Fields Group. A comparison is made between the operating costs 01the drilling rig and those of conventional hand-held machines, and it is concluded that, despite certain disadvantages, mechanical drilling is preferable.

Jan 1, 1988

By J. J. Van Rensburg

The commissioning of a test facility for the calibration of anemometers by J. J. VAN RENSBURG (Student Member). After the erection of a commercially produced open-jet wind tunnel for the calibration of the anemometers used in mine ventilation, the wind tunnel was calibrated for routine use. There is a choice of five orifice plates. which, together with a variable-speed fan, can give a measurable range of air velocities in the test section from about 0,05 to 35 m/so The orifice plates were calibrated against a standard pitot tube, and it is now necessary only to measure the pressure drop across an orifice plate and to read off, from a set of graphs, the true outlet velocity in the test section. The paper describes the underlying theory and the test results.

Jan 4, 1975

By M. Viljoen

South Africa has produced more than a third of the total gold mined throughout history and remains a major although, until recently, no longer the largest producer of gold. South African gold production peaked in 1970 with an output of 1 000 t, a major component of the western world?s gold production, with the development of the country?s economy having been based largely on this mineral wealth. The costs and difficulties of increasingly deep-level mining, coupled with increasing labour costs and the low gold price until relatively recently, have seen production fall steadily since then, with the closure of many mines including those of the Central Rand Goldfield in the mid seventies. Thus in 1998, only 464 t were produced, with 342 tons being produced in 2004. In 2006, 275 tons of gold were produced and after more than 100 years was the last year as the world?s largest gold producer. In 2008 gold production was 221 tons, making South Africa the third largest gold producer after China (292 t) and the USA (234 t). Gold production would have been lower if it had not been for massive tailings dam retreatment operations that started in the late seventies, including in the Central Rand Goldfield. Mining of a remaining deep and lower grade shallow resources has now also become a major focus and has recently lead to a rebirth of reef mining on the Central Rand Goldfield.

Jan 1, 2009

By F. L. D. Cloete

The Relix process is based on direct contact between an ion-exchange resin and undiluted pulp, thus avoiding prior solid-liquid separation. The resin particles float near the surface of the pulp, forming an inverted fluidized bed with the pulp flowing downwards. The basic idea was demonstrated on a full-scale pachuca tank at Stilfontein Gold Mine in 1970, followed by a small-scale demonstration run in a laboratory at the National Institute for Metallurgy. A pilot plant based on a throughput of 60 tons of ore per day was subsequently operated at West Driefontein Gold Mine for several periods over two years. Although the plant proved operable from a mechanical point of view, the metallurgical performance was not up to expectation. The basic cause of the poor metallurgical performace was shown to be backmixing of both the resin and the pulp between stages. The values obtained for resin losses were inconclusive. Further development of resin-in-pulp processes for the recovery of uranium should be focused on the performance of various techniques for the screening of resin from pulp.

Jan 1, 1981

By P. R. Levey, A. van Bennekom

The effects of nitrogen alloying on the corrosion properties of austenitic stainless steels were investigated by a combination of potentio-dynamic and surface analysis techniques. The results indicate that nitrogen undergoes the phenomenon of anodic segregation, affecting both general and localized corrosion resistance. Nitrogen alloying is found to be beneficial to general corrosion resistance in a de-aerated sulphuric acid solution, but to be detrimental in an aerated solution of sulphuric acid This phenomenon is explained in terms of an ammonium-ion polarization effect. Localized corrosion resistance is found to improve dramatically as a result of nitrogen alloying, the nitrogen improving the formation, maintenance, and stability of the passive film in environments that promote pitting various theories that have been proposed to account for these phenomena are discussed.

Jan 1, 1995

By H. M. Wells

The influence of economics on the design of mine shaft systems by H, M. WEI.LS, Pr. Eng., M.Se. (Fellow) The purpose of this paper is to review some of the more important economic criteria that must be taken into account when planning the number, type, size, and distribution of the shafts, or shaft systems, required to exploit a block of payable ore. The postulated philosophy governing the selection of design parameters is that of optimization of the financial return per rand of venture capital employed for the project as a whole. While this criterion may not necessarily satisfy the investment objective under all circumstances (as, for instance, where risk limitation is important), it does serve to place the relative economic advantages and disadvantages of specific design features, which may sometimes be in opposition, into correct perspective with respect to the overall economics of the project under the prevailing economic climate at the time of the investigation.

The relationships between backfill-transportation parameters (solids concentration, velocity, and pipe diameter) and the wear rate of backfill-transportation pipelines is well understood. However, the degree of wear experienced by a pipeline depends not only on the transportation parameters, but also on the characteristics of the solids making up the backfill, i.e. the particle-size distribution, hardness, shape, and sharpness of the particles. Therefore, unless data corresponding to the specific wear rate of the solids are available, the determination of the wear rate for pipes transporting an uncharacterized backfill is largely guesswork. This paper describes an evaluation of particle characteristics with special reference to particle sharpness so that pipe wear rates can be correlated with solids of different size distributions and sharpnesses.

Jan 1, 1993

By J. A. Ryder, M. U. Ozbay

An ERR-based methodology is presented for use in the re-assessment of the performance of stabilizing pillars, taking into account the effects of fracturing that can occur in pillar foundations under conditions of high stress. It is shown that the damage in the foundations of under-designed pillars can cause up to 30 per cent increases in ERR compared with the ERR for pillars with unfractured foundations. Despite this reduction in assessed performance, stabilizing pillars are still generally found to result in substantially lower ERR levels than alternative methods of reducing ERR, such as the use of stiff backfill or backfill ribs.

Jan 1, 1990

By V. M. Lovell, N. P. Finkelstein

The concepts involved in flotation research are discussed and aims are presented. Three different method. of investigation can be used, all of which are applied at the National Institute for Metallurgy (N.I.M.), and these are the empirical, trial and error method, the chemical engineering method, and the physicochemical approachs This paper is devoted to the last of these. Because of the complexity of the physicochemical interactions involved, the work has, to a large extent, been concentrated on only one aspect, viz. the interaction between the mineral surface and reagents in solution, which was considered of major importance in the understanding of the process. The aspects on which work has been done are the concentration of uranium, the reaction between salt minerals and fatty acids, mixed xanthate-cationic collector systems, and the reaction between sulphide minerals and thiol reagents. Selected problems from the first two of these are discussed in some detail and deal with the agglomeration flotation of uranium and the chemical control of the flotation process for phoscorite. A detailed discussion is also presented of the progress made in the understanding of the interaction between sulphide minerals and thiol reagents, which is of more general application. Finally, an indication is given of the future direction of physicochemical research at the N.I.M.

By M. J. Nicol

The results are reported of experiments on the influence of a number of variables on the rate of loading of gold cyanide onto activated carbon and the equilibrium capacity of the carbon. These variables include the concentrations of gold and free cyanide in solution, the pH value and ionic strength of the solution, the concentration of organic compounds in the solution, the temperature, the particle size of the carbon, and the mixing efficiency. The experiments were carried out under approximately steady-state conditions to simulate the conditions in a countercurrent carbon-in-pulp absorption plant. In addition, the results are reported of experiments to establish whether the absorption of gold cyanide onto activated carbon is a reversible process.

Jan 1, 1983